- 08 May, 2014 8 commits
-
-
Gregory CLEMENT authored
In order to boot the secondary CPUs on Armada 375, we need to set the boot address of these CPUs, through a register part of the System Controller (this deviates from the Armada XP design, where the boot address was defined using a register part of the PMSU unit). Therefore, this commit adds a new helper function in the System Controller driver to set the secondary CPU boot address. Moreover, it moves the System Controller initialization as an early_initcall(), since arch_initcall() is too late for an SMP-related initialization. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Link: https://lkml.kernel.org/r/1397483648-26611-7-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: https://lkml.kernel.org/r/1397483648-26611-7-git-send-email-thomas.petazzoni@free-electrons.comSigned-off-by:
Jason Cooper <jason@lakedaemon.net>
-
Jason Cooper authored
-
Thomas Petazzoni authored
This commit adds the CPU_METHOD_OF_DECLARE declaration for the Armada XP SMP operations. Note that the .smp_ops field of Armada XP DT_MACHINE structure is kept, in order to ensure we remain compatible with older Device Trees that do not include the "enable-method" property for the CPUs. Signed-off-by:
-
Thomas Petazzoni authored
The pmsu.c driver contained an armada_xp_boot_cpu() function that sets the boot address of a secondary CPUs and deasserts the reset. However, the Armada 375 needs a slightly different logic, so it makes more sense to move this code into the Armada XP specific platsmp.c. In order to achieve this, the mvebu_pmsu_set_cpu_boot_addr() function is exported. It will be needed for both the Armada XP and Armada 38x SMP implementations. Signed-off-by:
-
Jason Cooper authored
-
Sebastian Hesselbarth authored
Non-DT irq handlers were working through irq causes from most-significant to least-significant bit, while DT irqchip driver does it the other way round. This revealed some more HW issues on Kirkwood peripheral IP, where spurious sdio irqs can happen although irqs are masked. Also, the generated binaries show that original non-DT order compared to DT order save two instructions for each bit count check: irqchip DT order with ffs(): 60: e3a06001 mov r6, #1 64: e2643000 rsb r3, r4, #0 68: e0033004 and r3, r3, r4 6c: e16f3f13 clz r3, r3 70: e263301f rsb r3, r3, #31 74: e1c44316 bic r4, r4, r6, lsl r3 78: e5971004 ldr r1, [r7, #4] Original non-DT order with fls(): 60: e3a07001 mov r7, #1 64: e16f3f14 clz r3, r4 68: e263301f rsb r3, r3, #31 6c: e1c44317 bic r4, r4, r7, lsl r3 70: e5951004 ldr r1, [r5, #4] Therefore, reverse irq bit handling back to original order by replacing ffs() with fls(). Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Link: https://lkml.kernel.org/r/1398719528-23607-1-git-send-email-sebastian.hesselbarth@gmail.comAcked-by:
-
Thomas Petazzoni authored
Some irqchip initialization must be done on secondary CPUs. On mvebu platforms, this is currently achieved by having the arch/arm/mach-mvebu/platsmp.c code directly call into a function exported by the irqchip driver, which isn't really nice. This commit changes this by using the same solution as the one used in the GIC driver: the irqchip driver registers a CPU notifier, which is used to do the secondary CPU IRQ initialization. This way, the irqchip driver is completely autonomous, and the function no longer needs to be exposed from the irqchip driver to the SoC code. Signed-off-by:
-
Thomas Petazzoni authored
Instead of having the SoC code in arch/arm/mach-mvebu/platsmp.c do the set_smp_cross_call() to register the IPI-triggering function, it makes more sense to do exactly what the GIC driver is doing: let the irqchip driver do it. This way, it avoids having to expose the armada_mpic_send_doorbell() function between the irqchip driver and the SoC code. Signed-off-by:
-
- 24 Apr, 2014 14 commits
-
-
Gregory CLEMENT authored
Setting the start (or boot) address of a CPU is no more used only during SMP bring up on Armada 370/XP, but it will also be used by the CPU idle function of Armada XP, and by the Armada 38x SMP support. Therefore this commit creates a separate PMSU function to set the boot address of a CPU with the PMSU. Signed-off-by:
-
Gregory CLEMENT authored
The initial binding for PMSU was wrong, as it didn't take into account all the registers from the PMSU and moreover it referred to the CPU reset registers which are not part of PMSU. The Power Management Unit Service block also controls the Coherency Fabric subsystem. These registers are needed for the CPU idle implementation for the Armada 370/XP, it allows to enter a deep CPU idle state where the Coherency Fabric and the L2 cache are powered down. This commit adds support for a new compatible for the PMSU node which includes the registers related to the coherency fabric. It also keeps compatibility with the old compatible string. Signed-off-by:
-
Thomas Petazzoni authored
Until now, the PMSU driver was using of_iomap() to map its registers, but of_iomap() doesn't call request_mem_region(). This commit fixes the memory mapping code of the PMSU to do so, which will also be useful for a later commit since we will need to adjust the resource base address and size for Device Tree backward compatibility. Signed-off-by:
-
Thomas Petazzoni authored
This commit changes the PMSU driver to no longer map itself the CPU reset registers, and instead call into the CPU reset driver to deassert the secondary CPUs for SMP booting. In order to provide Device Tree backward compatibility, the CPU reset driver is extended to not only support its official compatible string "marvell,armada-370-cpu-reset", but to also look at the PMSU compatible string "marvell,armada-370-xp-pmsu" to find the CPU reset registers address. This allows old Device Tree to work correctly with newer kernel versions. Therefore, the CPU reset driver implements the following logic: * If one of the normal compatible strings "marvell,armada-370-cpu-reset" is found, then we map its first memory resource as the CPU reset registers. * Otherwise, if none of the normal compatible strings have been found, we look for the "marvell,armada-370-xp-pmsu" compatible string, and we map the second memory as the CPU reset registers. Signed-off-by:
-
Thomas Petazzoni authored
The Armada 370 and Armada XP have registers that allow to reset the CPUs, which is particularly useful to take the secondary CPUs out of reset in the context of the SMP support. Unfortunately, an implementation mistake was originally made and the support for these registers was integrated into the PMSU driver, which is in fact completely unrelated. And it turns out that the Armada 375 has the same CPU reset registers, but does not have the PMSU registers. Therefore, this commit creates a small CPU reset driver. All it does is provide a simple mvebu_cpu_reset_deassert() function that the SMP support code can call to take secondary CPUs out of reset. As of this commit, the driver isn't being used, it will be used through changes in the following commits. Note that we initially planned to use the 'reset controller' framework, but it requires the addition of "resets" properties in the Device Tree, which are causing too many problems if we want to keep the Device Tree backward compatibility. Moreover, the 'reset controller' framework is mainly useful when a device driver needs to request a reset of its device from a separate reset controller. In our case, the CPU reset handling and the SMP core code are both located in arch/arm/mach-mvebu/ and are tightly linked together, so there's no real benefit in going through a separate framework. Signed-off-by:
-
Thomas Petazzoni authored
The Armada 38x has a coherency unit that is similar to the one of the Armada 375 SoC, except that it does not have the bug of the Armada 375 coherency unit that requires the XOR based workaround. This commit therefore extends the Marvell EBU coherency code with a new compatible string to support the Armada 38x coherency unit. Signed-off-by:
-
Thomas Petazzoni authored
The early revisions of Armada 375 SOCs (Z1 stepping) have a bug in the I/O coherency unit that prevents using the normal method for the I/O coherency barrier. The recommended workaround is to use a XOR memset transfer to act as the I/O coherency barrier. This involves "borrowing" a XOR engine, which gets disabled in the Device Tree so the normal XOR driver doesn't use it. Signed-off-by:
-
Thomas Petazzoni authored
The Armada 375, like the Armada 370 and Armada XP, has a coherency unit. However, unlike the coherency unit of 370/XP which does both CPU and I/O coherency, the one on Armada 735 only does I/O coherency. Therefore, instead of having two sets of registers (the first one being used mainly to register each CPU in the coherency fabric, the second one being used for the I/O coherency barrier), it has only one set of register (for the I/O coherency barrier). This commit adds a new "marvell,armada-375-coherency-fabric" compatible string for this variant of the coherency fabric. The custom DMA operations, and the way of triggering an I/O barrier is the same as Armada 370/XP, so the code changes are minimal. However, the set_cpu_coherent() function is not needed on Armada 375 and will not work. Signed-off-by:
-
Thomas Petazzoni authored
Contrary to the Armada 370 and XP that used the PJ4B Marvell cores, the Armada 375 and Armada 38x use the ARM Cortex-A9. A consequence of this is that the unit responsible for the coherency between CPUs is now the ARM SCU, and not the Marvell coherency unit (which is still present to do coherency with I/O devices). Therefore this commit: * Ensures that the selection of the Armada 375 or Armada 38x SoC support enables the ARM SCU support in the kernel. * Make sure to initialize the SCU at boot time. Signed-off-by:
-
Thomas Petazzoni authored
In the mach-mvebu coherency code, instead of using of_find_matching_node() and then of_match_node(), directly use the of_find_matching_node_and_match() which does both at once. We take this opportunity to also simplify the initialization of the "type" variable. Signed-off-by:
-
Thomas Petazzoni authored
Until now, the mvebu-mbus was guessing by itself whether hardware I/O coherency was available or not by poking into the Device Tree to see if the coherency fabric Device Tree node was present or not. However, on some upcoming SoCs, the presence or absence of the coherency fabric DT node isn't sufficient: in CONFIG_SMP, the coherency can be enabled, but not in !CONFIG_SMP. In order to clean this up, the mvebu_mbus_dt_init() function is extended to get a boolean argument telling whether coherency is enabled or not. Therefore, the logic to decide whether coherency is available or not now belongs to the core SoC code instead of the mvebu-mbus driver itself, which is much better. Signed-off-by:
-
Thomas Petazzoni authored
This commit extends the coherency fabric code to provide a coherency_available()function that the SoC code can call to be told whether coherency support is available or not. On Armada 370/XP, coherency support is available as soon as the relevant DT node is present. On some upcoming SoCs, the DT node needs to be present *and* the system running with CONFIG_SMP enabled. Signed-off-by:
-
Thomas Petazzoni authored
The code that handles the coherency fabric of Armada 370 and Armada XP in arch/arm/mach-mvebu/coherency.c made the assumption that there was only one type of coherency fabric. Unfortunately, it turns out that upcoming SoCs have a slightly different coherency unit. In preparation to the introduction of the coherency support for more SoCs, this commit: * Introduces a data associated to the compatible string in the compatible string match table, so that the code can differantiate the variant of coherency unit being used. * Separates the coherency unit initialization code into its own function. Signed-off-by:
-
Andrew Lunn authored
Add the SoC Family, device ID and revision to /sys/bus/soc. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lkml.kernel.org/r/1393955507-26436-1-git-send-email-andrew@lunn.chSigned-off-by:
-
- 13 Apr, 2014 12 commits
-
-
Linus Torvalds authored
-
Geert Uytterhoeven authored
Some versions of gcc even warn about it: mm/shmem.c: In function ‘shmem_file_aio_read’: mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function If the loop is aborted during the first iteration by one of the two first break statements, error will be uninitialized. Introduced by commit 6e58e79d ("introduce copy_page_to_iter, kill loop over iovec in generic_file_aio_read()"). Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Geert Uytterhoeven authored
On 32 bit, size_t is "unsigned int", not "unsigned long", causing the following warning when comparing with PAGE_SIZE, which is always "unsigned long": fs/cifs/file.c: In function ‘cifs_readdata_to_iov’: fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast Introduced by commit 7f25bba8 ("cifs_iovec_read: keep iov_iter between the calls of cifs_readdata_to_iov()"), which changed the signedness of "remaining" and the code from min_t() to min(). Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linuxLinus Torvalds authored
Pull slab changes from Pekka Enberg: "The biggest change is byte-sized freelist indices which reduces slab freelist memory usage: https://lkml.org/lkml/2013/12/2/64" * 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: mm: slab/slub: use page->list consistently instead of page->lru mm/slab.c: cleanup outdated comments and unify variables naming slab: fix wrongly used macro slub: fix high order page allocation problem with __GFP_NOFAIL slab: Make allocations with GFP_ZERO slightly more efficient slab: make more slab management structure off the slab slab: introduce byte sized index for the freelist of a slab slab: restrict the number of objects in a slab slab: introduce helper functions to get/set free object slab: factor out calculate nr objects in cache_estimate -
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuildLinus Torvalds authored
Pull misc kbuild changes from Michal Marek: "Here is the non-critical part of kbuild: - One bogus coccinelle check removed, one check fixed not to suggest the obsolete PTR_RET macro - scripts/tags.sh does not index the generated *.mod.c files - new objdiff tool to list differences between two versions of an object file - A fix for scripts/bootgraph.pl" * 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: scripts/coccinelle: Use PTR_ERR_OR_ZERO scripts/bootgraph.pl: Add graphic header scripts: objdiff: detect object code changes between two commits Coccicheck: Remove memcpy to struct assignment test scripts/tags.sh: Ignore *.mod.c -
Mikulas Patocka authored
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk returns QUEUE FULL status. When the controller encounters an error (including QUEUE FULL or BUSY status), it aborts all not yet submitted requests in the function sym_dequeue_from_squeue. This function aborts them with DID_SOFT_ERROR. If the disk has full tag queue, the request that caused the overflow is aborted with QUEUE FULL status (and the scsi midlayer properly retries it until it is accepted by the disk), but the sym53c8xx_2 driver aborts the following requests with DID_SOFT_ERROR --- for them, the midlayer does just a few retries and then signals the error up to sd. The result is that disk returning QUEUE FULL causes request failures. The error was reproduced on 53c895 with COMPAQ BD03685A24 disk (rebranded ST336607LC) with command queue 48 or 64 tags. The disk has 64 tags, but under some access patterns it return QUEUE FULL when there are less than 64 pending tags. The SCSI specification allows returning QUEUE FULL anytime and it is up to the host to retry. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Cc: Matthew Wilcox <matthew@wil.cx> Cc: James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Paul Mackerras authored
Commit 8f619b54 ("powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early") added code to set the AIL bit in the LPCR without checking whether the kernel is running in hypervisor mode. The result is that when the kernel is running as a guest (i.e., under PowerKVM or PowerVM), the processor takes a privileged instruction interrupt at that point, causing a panic. The visible result is that the kernel hangs after printing "returning from prom_init". This fixes it by checking for hypervisor mode being available before setting LPCR. If we are not in hypervisor mode, we enable relocation-on interrupts later in pSeries_setup_arch using the H_SET_MODE hcall. Signed-off-by:
Paul Mackerras <paulus@samba.org> Acked-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Davidlohr Bueso authored
Commits 11d4616b ("futex: revert back to the explicit waiter counting code") and 69cd9eba ("futex: avoid race between requeue and wake") changed some of the finer details of how we think about futexes. One was a late fix and the other a consequence of overlooking the whole requeuing logic. The first change caused our documentation to be incorrect, and the second made us aware that we need to explicitly add more details to it. Signed-off-by:
Davidlohr Bueso <davidlohr@hp.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull yet more networking updates from David Miller: 1) Various fixes to the new Redpine Signals wireless driver, from Fariya Fatima. 2) L2TP PPP connect code takes PMTU from the wrong socket, fix from Dmitry Petukhov. 3) UFO and TSO packets differ in whether they include the protocol header in gso_size, account for that in skb_gso_transport_seglen(). From Florian Westphal. 4) If VLAN untagging fails, we double free the SKB in the bridging output path. From Toshiaki Makita. 5) Several call sites of sk->sk_data_ready() were referencing an SKB just added to the socket receive queue in order to calculate the second argument via skb->len. This is dangerous because the moment the skb is added to the receive queue it can be consumed in another context and freed up. It turns out also that none of the sk->sk_data_ready() implementations even care about this second argument. So just kill it off and thus fix all these use-after-free bugs as a side effect. 6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti. 7) pktgen needs to do locking properly for LLTX devices, from Daniel Borkmann. 8) xen-netfront driver initializes TX array entries in RX loop :-) From Vincenzo Maffione. 9) After refactoring, some tunnel drivers allow a tunnel to be configured on top itself. Fix from Nicolas Dichtel. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits) vti: don't allow to add the same tunnel twice gre: don't allow to add the same tunnel twice drivers: net: xen-netfront: fix array initialization bug pktgen: be friendly to LLTX devices r8152: check RTL8152_UNPLUG net: sun4i-emac: add promiscuous support net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO net: ipv6: Fix oif in TCP SYN+ACK route lookup. drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts drivers: net: cpsw: discard all packets received when interface is down net: Fix use after free by removing length arg from sk_data_ready callbacks. Drivers: net: hyperv: Address UDP checksum issues Drivers: net: hyperv: Negotiate suitable ndis version for offload support Drivers: net: hyperv: Allocate memory for all possible per-pecket information bridge: Fix double free and memory leak around br_allowed_ingress bonding: Remove debug_fs files when module init fails i40evf: program RSS LUT correctly i40evf: remove open-coded skb_cow_head ixgb: remove open-coded skb_cow_head igbvf: remove open-coded skb_cow_head ... -
Linus Torvalds authored
Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux Pull blackfin updates from Steven Miao: "Code cleanup, some previously ignored patches, and bug fixes" * tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux: blackfin: cleanup board files bf609: clock: drop unused clock bit set/clear functions Blackfin: bf537: rename "CONFIG_ADT75" Blackfin: bf537: rename "CONFIG_AD7314" Blackfin: bf537: rename ad2s120x ->ad2s1200 blackfin: bf537: fix typo "CONFIG_SND_SOC_ADV80X_MODULE" blackfin: dma: current count mmr is read only bfin_crc: Move architecture independant crc header file out of the blackfin folder. bf54x: drop unuesd HOST status,control,timeout registers bit define macros blackfin: portmux: cleanup head file Blackfin: remove "config IP_CHECKSUM_L1" blackfin: Remove GENERIC_GPIO config option again blackfin:Use generic /proc/interrupts implementation blackfin: bf60x: fix typo "CONFIG_PM_BFIN_WAKE_PA15_POL"
-
Linus Torvalds authored
Merge tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc Pull remoteproc cleanups from Ohad Ben-Cohen: "Several remoteproc cleanup patches coming from Jingoo Han, Julia Lawall and Uwe Kleine-König" * tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc: remoteproc/ste_modem: staticize local symbols remoteproc/davinci: simplify use of devm_ioremap_resource remoteproc/davinci: drop needless devm_clk_put
-
git://git.linuxfoundation.org/llvmlinux/kernelLinus Torvalds authored
Pull llvm patches from Behan Webster: "These are some initial updates to support compiling the kernel with clang. These patches have been through the proper reviews to the best of my ability, and have been soaking in linux-next for a few weeks. These patches by themselves still do not completely allow clang to be used with the kernel code, but lay the foundation for other patches which are still under review. Several other of the LLVMLinux patches have been already added via maintainer trees" * tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel: x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id" x86 kbuild: LLVMLinux: More cc-options added for clang x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI LLVMLinux: Add support for clang to compiler.h and new compiler-clang.h LLVMLinux: Remove warning about returning an uninitialized variable kbuild: LLVMLinux: Fix LINUX_COMPILER definition script for compilation with clang Documentation: LLVMLinux: Update Documentation/dontdiff kbuild: LLVMLinux: Adapt warnings for compilation with clang kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang
-
- 12 Apr, 2014 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pendingLinus Torvalds authored
Pull SCSI target updates from Nicholas Bellinger: "Here are the target pending updates for v3.15-rc1. Apologies in advance for waiting until the second to last day of the merge window to send these out. The highlights this round include: - iser-target support for T10 PI (DIF) offloads (Sagi + Or) - Fix Task Aborted Status (TAS) handling in target-core (Alex Leung) - Pass in transport supported PI at session initialization (Sagi + MKP + nab) - Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi) - Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab) - Fix tcm_fc use-after-free of ft_tpg (Andy Grover) - Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn) Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI metadata into KVM guest have been left-out for now, as there where a few comments from MST + Paolo that where not able to be addressed in time for v3.15. Please expect this feature for v3.16-rc1" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits) ib_srpt: Use correct ib_sg_dma primitives target/tcm_fc: Rename ft_tport_create to ft_tport_get target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn target/tcm_fc: Rename structs and list members for clarity target/tcm_fc: Limit to 1 TPG per wwn target/tcm_fc: Don't export ft_lport_list target/tcm_fc: Fix use-after-free of ft_tpg target: Add check to prevent Abort Task from aborting itself target: Enable READ_STRIP emulation in target_complete_ok_work target/sbc: Add sbc_dif_read_strip software emulation target: Enable WRITE_INSERT emulation in target_execute_cmd target/sbc: Add sbc_dif_generate software emulation target/sbc: Only expose PI read_cap16 bits when supported by fabric target/spc: Only expose PI mode page bits when supported by fabric target/spc: Only expose PI inquiry bits when supported by fabric target: Pass in transport supported PI at session initialization target/iblock: Fix double bioset_integrity_free bug Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist target/rd: T10-Dif: RAM disk is allocating more space than required. iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media fixes from Mauro Carvalho Chehab: "A series of bug fix patches for v3.15-rc1. Most are just driver fixes. There are some changes at remote controller core level, fixing some definitions on a new API added for Kernel v3.15. It also adds the missing include at include/uapi/linux/v4l2-common.h, to allow its compilation on userspace, as pointed by you" * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (24 commits) [media] gpsca: remove the risk of a division by zero [media] stk1160: warrant a NUL terminated string [media] v4l: ti-vpe: retain v4l2_buffer flags for captured buffers [media] v4l: ti-vpe: Set correct field parameter for output and capture buffers [media] v4l: ti-vpe: zero out reserved fields in try_fmt [media] v4l: ti-vpe: Fix initial configuration queue data [media] v4l: ti-vpe: Use correct bus_info name for the device in querycap [media] v4l: ti-vpe: report correct capabilities in querycap [media] v4l: ti-vpe: Allow usage of smaller images [media] v4l: ti-vpe: Use video_device_release_empty [media] v4l: ti-vpe: Make sure in job_ready that we have the needed number of dst_bufs [media] lgdt3305: include sleep functionality in lgdt3304_ops [media] drx-j: use customise option correctly [media] m88rs2000: fix sparse static warnings [media] r820t: fix size and init values [media] rc-core: remove generic scancode filter [media] rc-core: split dev->s_filter [media] rc-core: do not change 32bit NEC scancode format for now [media] rtl28xxu: remove duplicate ID 0458:707f Genius TVGo DVB-T03 [media] xc2028: add missing break to switch ...
-
git://github.com/jonmason/ntbLinus Torvalds authored
Pull PCIe non-transparent bridge fixes and features from Jon Mason: "NTB driver bug fixes to address issues in list traversal, skb leak in ntb_netdev, a typo, and a leak of msix entries in the error path. Clean ups of the event handling logic, as well as a overall style cleanup. Finally, the driver was converted to use the new pci_enable_msix_range logic (and the refactoring to go along with it)" * tag 'ntb-3.15' of git://github.com/jonmason/ntb: ntb: Use pci_enable_msix_range() instead of pci_enable_msix() ntb: Split ntb_setup_msix() into separate BWD/SNB routines ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs NTB: Code Style Clean-up NTB: client event cleanup ntb: Fix leakage of ntb_device::msix_entries[] array NTB: Fix typo in setting one translation register ntb_netdev: Fix skb free issue in open ntb_netdev: Fix list_for_each_entry exit issue
-
Linus Torvalds authored
The vfs merge caused a latent bug to show up: In file included from fs/ceph/super.h:4:0, from fs/ceph/ioctl.c:3: include/linux/ceph/ceph_debug.h:4:0: warning: "pr_fmt" redefined [enabled by default] #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt ^ In file included from include/linux/kernel.h:13:0, from include/linux/uio.h:12, from include/linux/socket.h:7, from include/uapi/linux/in.h:22, from include/linux/in.h:23, from fs/ceph/ioctl.c:1: include/linux/printk.h:214:0: note: this is the location of the previous definition #define pr_fmt(fmt) fmt ^ where the reason is that <linux/ceph_debug.h> is included much too late for the "pr_fmt()" define. The include of <linux/ceph_debug.h> needs to be the first include in the file, but fs/ceph/ioctl.c had for some reason missed that, and it wasn't noticeable until some unrelated header file changes brought in an indirect earlier include of <linux/kernel.h>. Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs updates from Al Viro: "The first vfs pile, with deep apologies for being very late in this window. Assorted cleanups and fixes, plus a large preparatory part of iov_iter work. There's a lot more of that, but it'll probably go into the next merge window - it *does* shape up nicely, removes a lot of boilerplate, gets rid of locking inconsistencie between aio_write and splice_write and I hope to get Kent's direct-io rewrite merged into the same queue, but some of the stuff after this point is having (mostly trivial) conflicts with the things already merged into mainline and with some I want more testing. This one passes LTP and xfstests without regressions, in addition to usual beating. BTW, readahead02 in ltp syscalls testsuite has started giving failures since "mm/readahead.c: fix readahead failure for memoryless NUMA nodes and limit readahead pages" - might be a false positive, might be a real regression..." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits) missing bits of "splice: fix racy pipe->buffers uses" cifs: fix the race in cifs_writev() ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure kill generic_file_buffered_write() ocfs2_file_aio_write(): switch to generic_perform_write() ceph_aio_write(): switch to generic_perform_write() xfs_file_buffered_aio_write(): switch to generic_perform_write() export generic_perform_write(), start getting rid of generic_file_buffer_write() generic_file_direct_write(): get rid of ppos argument btrfs_file_aio_write(): get rid of ppos kill the 5th argument of generic_file_buffered_write() kill the 4th argument of __generic_file_aio_write() lustre: don't open-code kernel_recvmsg() ocfs2: don't open-code kernel_recvmsg() drbd: don't open-code kernel_recvmsg() constify blk_rq_map_user_iov() and friends lustre: switch to kernel_sendmsg() ocfs2: don't open-code kernel_sendmsg() take iov_iter stuff to mm/iov_iter.c process_vm_access: tidy up a bit ...
-
David S. Miller authored
Nicolas Dichtel says: ==================== tunnels: don't allow to add the same tunnel twice This series fixes the check of an existing tunnel with the same parameters when a new tunnel is added. I've checked all users of ip_tunnel_newlink(): gre, gretap, ipip and vti. The bug exists only for gre and vti. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
