Skip to content

L
linux
Switch branch/tag
  1. 25 Jul, 2013 7 commits
    • Greg Kroah-Hartman's avatar
      Merge tag 'for-usb-linus-2013-07-25' of... · 00c5ec28
      Greg Kroah-Hartman authored 
      Merge tag 'for-usb-linus-2013-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:

xhci: Bug fixes, now with more tags!

Hi Greg,

Here's five bug fixes for 3.12.

The three patches are marked for stable.  Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.

The other two patches fix build warnings.

Sarah Sharp
      00c5ec28
    • Oleksij Rempel's avatar
      xhci: fix null pointer dereference on ring_doorbell_for_active_rings · d66eaf9f
      Oleksij Rempel authored 
      in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.

This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: default avatarOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      d66eaf9f
    • George Cherian's avatar
      usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0 · 07f3cb7c
      George Cherian authored 
      Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.

Note from Sarah:

The xHCI 1.0 spec changed how hardware handles short packets.  The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set).  On the second successful status, that warning will be
triggered in the driver.

Software is now supposed to not assume the TD is not completed until it
gets that last successful status.  That means we have a slight race
condition, although it should have little practical impact.  This patch
papers over that issue.

It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable.  This
patch is needed for stable to avoid serious log spam.

This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333 "Intel xhci:
Ignore spurious successful event."

The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: default avatarGeorge Cherian <george.cherian@ti.com>
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      07f3cb7c
    • Randy Dunlap's avatar
      usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled · c4d949b7
      Randy Dunlap authored 
      Fix warning when CONFIG_PCI is not enabled
(from commit 29636578).

drivers/usb/host/pci-quirks.h: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: default avatarRandy Dunlap <rdunlap@infradead.org>
Reported-by: default avatarGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
      c4d949b7
    • Olof Johansson's avatar
      usb: xhci: Mark two functions __maybe_unused · d5c82feb
      Olof Johansson authored 
      Resolves the following build warnings:
drivers/usb/host/xhci.c:332:13: warning: 'xhci_msix_sync_irqs' defined but not used [-Wunused-function]
drivers/usb/host/xhci.c:3901:12: warning: 'xhci_change_max_exit_latency' defined but not used [-Wunused-function]

These functions are not always used, and since they're marked static
they will produce build warnings:
- xhci_msix_sync_irqs is only used with CONFIG_PCI.
- xhci_change_max_exit_latency is a little more complicated with
  dependencies on CONFIG_PM and CONFIG_PM_RUNTIME.

Instead of building a bigger maze of ifdefs in this code, I've just
marked both with __maybe_unused.
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
      d5c82feb
    • Sarah Sharp's avatar
      xhci: Avoid NULL pointer deref when host dies. · 203a8661
      Sarah Sharp authored 
      When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().

The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL.  The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.

However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory.  xhci_free_dev checks the return value from the generic
xhci_check_args function.  If the return value is -ENODEV, it carries on
trying to free the virtual device.

The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer.  It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.

The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.

See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details.  This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.

This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b40 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: default avatarSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: default avatarVincent Thiele <vincentthiele@gmail.com>
Cc: stable@vger.kernel.org
      203a8661
    • Enrico Mioso's avatar
      usb: serial: option: Add ONYX 3G device support · 63b5df96
      Enrico Mioso authored 
      This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: default avatarEnrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      63b5df96
  3. 24 Jul, 2013 1 commit
  5. 23 Jul, 2013 2 commits
    • Bjørn Mork's avatar
      usb: option: add TP-LINK MA260 · 94190301
      Bjørn Mork authored 
      Signed-off-by: default avatarBjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      94190301
    • Alexandr \"Sky\" Ivanov's avatar
      USB: option: add D-Link DWM-152/C1 and DWM-156/C1 · ca247635
      Alexandr \"Sky\" Ivanov authored 
      Adding support for D-Link DWM-152/C1 and DWM-156/C1 devices.

DWM-152/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e01 Rev= 0.00
S:  Product=USB Configuration
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

DWM-156/C1:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  8 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=07d1 ProdID=3e02 Rev= 0.00
S:  Product=DataCard Device
S:  SerialNumber=1234567890ABCDEF
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: default avatarAlexandr Ivanov <alexandr.sky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      ca247635
  7. 22 Jul, 2013 7 commits
  9. 16 Jul, 2013 3 commits
    • Alan Stern's avatar
      USB: global suspend and remote wakeup don't mix · e583d9db
      Alan Stern authored 
      The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses.  This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets.  The idea was to save
time and to avoid certain kinds of wakeup races.

Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).

We can't have hubs dropping wakeup requests.  Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup.  People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.

In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup.  A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.

This should be applied to the 3.10 stable kernel.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: default avatarToralf Förster <toralf.foerster@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      e583d9db
    • Alan Stern's avatar
      USB: move the definition of USB_MAXCHILDREN · 36ff66db
      Alan Stern authored 
      The USB_MAXCHILDREN symbol is used in include/uapi/linux/usb/ch11.h, a
user-mode header, even though it is defined in include/linux/usb.h,
which is kernel-only.  This causes compile-time errors when user
programs try to #include linux/usb/ch11.h.

This patch fixes the problem by moving the definition of USB_MAXCHILDREN
into ch11.h.  It also gets rid of unneeded parentheses.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      36ff66db
    • Greg Kroah-Hartman's avatar
      Merge tag 'fixes-for-v3.11-rc1' of... · 39c24270
      Greg Kroah-Hartman authored 
      Merge tag 'fixes-for-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.11-rc1

Quite a few changes going on here. They have been
boot tested on OMAP5 and compile tested on ARM and x86
with different defconfigs.

Many gadget drivers got a depends on HAS_DMA in order
to prevent build failures on !HAS_DMA architectures.

DWC3 learned how to allow a gadget driver to be modprobed
after an unsuccessful modprobe of another gadget driver. It
also got a fix to a wrong bit mask in dwc3_event_type, and
learns to return proper error codes from failed usb3_phy
initialization.

RNDIS function driver can now be built with configfs.

at91_udc now knows that we need to prepare the clock
before enabling it.

renesas_usbhs now lets gadget drivers be modprobed
multiple times.

phy-omap-usb3 got a fix for the DPLL settings.

mv_u3d_core now passes the correct cookie to free_irq().

fotg210-udc got Section mismatch fixes.
Signed-of-by: default avatarFelipe Balbi <balbi@ti.com>
      39c24270
  11. 15 Jul, 2013 16 commits
  13. 14 Jul, 2013 4 commits
    • Linus Torvalds's avatar
      Linux 3.11-rc1 · ad81f054
      Linus Torvalds authored
      ad81f054
    • Linus Torvalds's avatar
      Merge branch 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux · 54be8200
      Linus Torvalds authored 
      Pull slab update from Pekka Enberg:
 "Highlights:

  - Fix for boot-time problems on some architectures due to
    init_lock_keys() not respecting kmalloc_caches boundaries
    (Christoph Lameter)

  - CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)

  - Fix for excessive slab freelist draining (Wanpeng Li)

  - SLUB and SLOB cleanups and fixes (various people)"

I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.

* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
  slub: Check for page NULL before doing the node_match check
  mm/slab: Give s_next and s_stop slab-specific names
  slob: Check for NULL pointer before calling ctor()
  slub: Make cpu partial slab support configurable
  slab: add kmalloc() to kernel API documentation
  slab: fix init_lock_keys
  slob: use DIV_ROUND_UP where possible
  slub: do not put a slab to cpu partial list when cpu_partial is 0
  mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
  mm/slub: Drop unnecessary nr_partials
  mm/slab: Fix /proc/slabinfo unwriteable for slab
  mm/slab: Sharing s_next and s_stop between slab and slub
  mm/slab: Fix drain freelist excessively
  slob: Rework #ifdeffery in slab.h
  mm, slab: moved kmem_cache_alloc_node comment to correct place
      54be8200
    • Steven Rostedt's avatar
      slub: Check for page NULL before doing the node_match check · c25f195e
      Steven Rostedt authored 
      In the -rt kernel (mrg), we hit the following dump:

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
PGD a2d39067 PUD b1641067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: sunrpc cpufreq_ondemand ipv6 tg3 joydev sg serio_raw pcspkr k8temp amd64_edac_mod edac_core i2c_piix4 e100 mii shpchp ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom sata_svw ata_generic pata_acpi pata_serverworks radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod
CPU 3
Pid: 20878, comm: hackbench Not tainted 3.6.11-rt25.14.el6rt.x86_64 #1 empty empty/Tyan Transport GT24-B3992
RIP: 0010:[<ffffffff811573f1>]  [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
RSP: 0018:ffff8800a9b17d70  EFLAGS: 00010213
RAX: 0000000000000000 RBX: 0000000001200011 RCX: ffff8800a06d8000
RDX: 0000000004d92a03 RSI: 00000000000000d0 RDI: ffff88013b805500
RBP: ffff8800a9b17dc0 R08: ffff88023fd14d10 R09: ffffffff81041cbd
R10: 00007f4e3f06e9d0 R11: 0000000000000246 R12: ffff88013b805500
R13: ffff8801ff46af40 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f4e3f06e700(0000) GS:ffff88023fd00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000000a2d3a000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process hackbench (pid: 20878, threadinfo ffff8800a9b16000, task ffff8800a06d8000)
Stack:
 ffff8800a9b17da0 ffffffff81202e08 ffff8800a9b17de0 000000d001200011
 0000000001200011 0000000001200011 0000000000000000 0000000000000000
 00007f4e3f06e9d0 0000000000000000 ffff8800a9b17e60 ffffffff81041cbd
Call Trace:
 [<ffffffff81202e08>] ? current_has_perm+0x68/0x80
 [<ffffffff81041cbd>] copy_process+0xdd/0x15b0
 [<ffffffff810a2125>] ? rt_up_read+0x25/0x30
 [<ffffffff8104369a>] do_fork+0x5a/0x360
 [<ffffffff8107c66b>] ? migrate_enable+0xeb/0x220
 [<ffffffff8100b068>] sys_clone+0x28/0x30
 [<ffffffff81527423>] stub_clone+0x13/0x20
 [<ffffffff81527152>] ? system_call_fastpath+0x16/0x1b
Code: 89 fc 89 75 cc 41 89 d6 4d 8b 04 24 65 4c 03 04 25 48 ae 00 00 49 8b 50 08 4d 8b 28 49 8b 40 10 4d 85 ed 74 12 41 83 fe ff 74 27 <48> 8b 00 48 c1 e8 3a 41 39 c6 74 1b 8b 75 cc 4c 89 c9 44 89 f2
RIP  [<ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
 RSP <ffff8800a9b17d70>
CR2: 0000000000000000
---[ end trace 0000000000000002 ]---

Now, this uses SLUB pretty much unmodified, but as it is the -rt kernel
with CONFIG_PREEMPT_RT set, spinlocks are mutexes, although they do
disable migration. But the SLUB code is relatively lockless, and the
spin_locks there are raw_spin_locks (not converted to mutexes), thus I
believe this bug can happen in mainline without -rt features. The -rt
patch is just good at triggering mainline bugs ;-)

Anyway, looking at where this crashed, it seems that the page variable
can be NULL when passed to the node_match() function (which does not
check if it is NULL). When this happens we get the above panic.

As page is only used in slab_alloc() to check if the node matches, if
it's NULL I'm assuming that we can say it doesn't and call the
__slab_alloc() code. Is this a correct assumption?
Acked-by: default avatarChristoph Lameter <cl@linux.com>
Signed-off-by: default avatarSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: default avatarPekka Enberg <penberg@kernel.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      c25f195e
    • Linus Torvalds's avatar
      Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs · 41d9884c
      Linus Torvalds authored 
      Pull more vfs stuff from Al Viro:
 "O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
  making simple_lookup() usable for filesystems with non-NULL s_d_op,
  which allows us to get rid of quite a bit of ugliness"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  sunrpc: now we can just set ->s_d_op
  cgroup: we can use simple_lookup() now
  efivarfs: we can use simple_lookup() now
  make simple_lookup() usable for filesystems that set ->s_d_op
  configfs: don't open-code d_alloc_name()
  __rpc_lookup_create_exclusive: pass string instead of qstr
  rpc_create_*_dir: don't bother with qstr
  llist: llist_add() can use llist_add_batch()
  llist: fix/simplify llist_add() and llist_add_batch()
  fput: turn "list_head delayed_fput_list" into llist_head
  fs/file_table.c:fput(): add comment
  Safer ABI for O_TMPFILE
      41d9884c
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7