- 22 Mar, 2016 2 commits
-
-
Johannes Berg authored
commit cb150b9d upstream. Since cfg80211 frequently takes actions from its netdev notifier call, wireless extensions messages could still be ordered badly since the wext netdev notifier, since wext is built into the kernel, runs before the cfg80211 netdev notifier. For example, the following can happen: 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff 5: wlan1: <BROADCAST,MULTICAST,UP> link/ether when setting the interface down causes the wext message. To also fix this, export the wireless_nlevent_flush() function and also call it from the cfg80211 notifier. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [ kamal: backport to 3.13-stable: context ] Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Johannes Berg authored
commit 8bf86273 upstream. Beniamino reported that he was getting an RTM_NEWLINK message for a given interface, after the RTM_DELLINK for it. It turns out that the message is a wireless extensions message, which was sent because the interface had been connected and disconnection while it was deleted caused a wext message. For its netlink messages, wext uses RTM_NEWLINK, but the message is without all the regular rtnetlink attributes, so "ip monitor link" prints just rudimentary information: 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff 5: wlan1: <BROADCAST,MULTICAST,UP> link/ether (from my hwsim reproduction) This can cause userspace to get confused since it doesn't expect an RTM_NEWLINK message after RTM_DELLINK. The reason for this is that wext schedules a worker to send out the messages, and the scheduling delay can cause the messages to get out to userspace in different order. To fix this, have wext register a netdevice notifier and flush out any pending messages when netdevice state changes. This fixes any ordering whenever the original message wasn't sent by a notifier itself. Reported-by:
Beniamino Galvani <bgalvani@redhat.com> Signed-off-by:
-
- 15 Mar, 2016 2 commits
-
-
Vladis Dronov authored
commit 8e20cf2b upstream. The aiptek driver crashes in aiptek_probe() when a specially crafted USB device without endpoints is detected. This fix adds a check that the device has proper configuration expected by the driver. Also an error return value is changed to more matching one in one of the error paths. Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Greg Kroah-Hartman authored
In Linus's tree, the iovec code has been reworked massively, but in older kernels the AIO layer should be checking this before passing the request on to other layers. Many thanks to Ben Hawkes of Google Project Zero for pointing out the issue. Reported-by:
Ben Hawkes <hawkes@google.com> Acked-by:
Benjamin LaHaise <bcrl@kvack.org> Tested-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Moritz Muehlenhoff <jmm@inutil.org> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
- 14 Mar, 2016 1 commit
-
-
Kamal Mostafa authored
Signed-off-by:
-
- 10 Mar, 2016 35 commits
-
-
Willy Tarreau authored
commit 759c0114 upstream. On no-so-small systems, it is possible for a single process to cause an OOM condition by filling large pipes with data that are never read. A typical process filling 4000 pipes with 1 MB of data will use 4 GB of memory. On small systems it may be tricky to set the pipe max size to prevent this from happening. This patch makes it possible to enforce a per-user soft limit above which new pipes will be limited to a single page, effectively limiting them to 4 kB each, as well as a hard limit above which no new pipes may be created for this user. This has the effect of protecting the system against memory abuse without hurting other users, and still allowing pipes to work correctly though with less data at once. The limit are controlled by two new sysctls : pipe-user-pages-soft, and pipe-user-pages-hard. Both may be disabled by setting them to zero. The default soft limit allows the default number of FDs per process (1024) to create pipes of the default size (64kB), thus reaching a limit of 64MB before starting to create only smaller pipes. With 256 processes limited to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB = 1084 MB of memory allocated for a user. The hard limit is disabled by default to avoid breaking existing applications that make intensive use of pipes (eg: for splicing). Reported-by: socketpair@gmail.com Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Mitigates: CVE-2013-4312 (Linux 2.0+) Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Rainer Weikusat authored
commit 1b92ee3d upstream. The present unix_stream_read_generic contains various code sequences of the form err = -EDISASTER; if (<test>) goto out; This has the unfortunate side effect of possibly causing the error code to bleed through to the final out: return copied ? : err; and then to be wrongly returned if no data was copied because the caller didn't supply a data buffer, as demonstrated by the program available at http://pad.lv/1540731 Change it such that err is only set if an error condition was detected. Fixes: 3822b5c2 ("af_unix: Revert 'lock_interruptible' in stream receive code") Reported-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [ luis: backported to 3.16: - modify unix_stream_recvmsg() instead of unix_stream_read_generic() - adjusted context ] Signed-off-by:
-
Eugenia Emantayev authored
commit 31c128b6 upstream. Previously, the shift value used for time-stamping was constant and didn't depend on the HW chip frequency. Change that to take the frequency into account and calculate the maximal value in cycles per wraparound of ten seconds. This time slot was chosen since it gives a good accuracy in time synchronization. Algorithm for shift value calculation: * Round up the maximal value in cycles to nearest power of two * Calculate maximal multiplier by division of all 64 bits set to above result * Then, invert the function clocksource_khz2mult() to get the shift from maximal mult value Fixes: ec693d47 ('net/mlx4_en: Add HW timestamping (TS) support') Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Reviewed-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Eric Dumazet authored
commit 91948309 upstream. Dmitry reported memory leaks of IP options allocated in ip_cmsg_send() when/if this function returns an error. Callers are responsible for the freeing. Many thanks to Dmitry for the report and diagnostic. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Jay Vosburgh authored
commit 21a75f09 upstream. The current logic in bond_arp_rcv will accept an incoming ARP for validation if (a) the receiving slave is either "active" (which includes the currently active slave, or the current ARP slave) or, (b) there is a currently active slave, and it has received an ARP since it became active. For case (b), the receiving slave isn't the currently active slave, and is receiving the original broadcast ARP request, not an ARP reply from the target. This logic can fail if there is no currently active slave. In this situation, the ARP probe logic cycles through all slaves, assigning each in turn as the "current_arp_slave" for one arp_interval, then setting that one as "active," and sending an ARP probe from that slave. The current logic expects the ARP reply to arrive on the sending current_arp_slave, however, due to switch FDB updating delays, the reply may be directed to another slave. This can arise if the bonding slaves and switch are working, but the ARP target is not responding. When the ARP target recovers, a condition may result wherein the ARP target host replies faster than the switch can update its forwarding table, causing each ARP reply to be sent to the previous current_arp_slave. This will never pass the logic in bond_arp_rcv, as neither of the above conditions (a) or (b) are met. Some experimentation on a LAN shows ARP reply round trips in the 200 usec range, but my available switches never update their FDB in less than 4000 usec. This patch changes the logic in bond_arp_rcv to additionally accept an ARP reply for validation on any slave if there is a current ARP slave and it sent an ARP probe during the previous arp_interval. Fixes: aeea64ac ("bonding: don't trust arp requests unless active slave really works") Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Neil Horman authored
commit d9749fb5 upstream. Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in its size computation, observing that the current method never guaranteed that the hashsize (measured in number of entries) would be a power of two, which the input hash function for that table requires. The root cause of the problem is that two values need to be computed (one, the allocation order of the storage requries, as passed to __get_free_pages, and two the number of entries for the hash table). Both need to be ^2, but for different reasons, and the existing code is simply computing one order value, and using it as the basis for both, which is wrong (i.e. it assumes that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not). To fix this, we change the logic slightly. We start by computing a goal allocation order (which is limited by the maximum size hash table we want to support. Then we attempt to allocate that size table, decreasing the order until a successful allocation is made. Then, with the resultant successful order we compute the number of buckets that hash table supports, which we then round down to the nearest power of two, giving us the number of entries the table actually supports. I've tested this locally here, using non-debug and spinlock-debug kernels, and the number of entries in the hashtable consistently work out to be powers of two in all cases. Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Reported-by:
-
Dmitry V. Levin authored
commit b5f05492 upstream. The value passed by unix_diag_get_exact to unix_lookup_by_ino has type __u32, but unix_lookup_by_ino's argument ino has type int, which is not a problem yet. However, when ino is compared with sock_i_ino return value of type unsigned long, ino is sign extended to signed long, and this results to incorrect comparison on 64-bit architectures for inode numbers greater than INT_MAX. This bug was found by strace test suite. Fixes: 5d3cae8b ("unix_diag: Dumping exact socket core") Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Anton Protopopov authored
commit a97eb33f upstream. An error response from a RTM_GETNETCONF request can return the positive error value EINVAL in the struct nlmsgerr that can mislead userspace. Signed-off-by:
Anton Protopopov <a.s.protopopov@gmail.com> Acked-by:
-
Guillaume Nault authored
commit 29e73269 upstream. Drop reference on the relay_po socket when __pppoe_xmit() succeeds. This is already handled correctly in the error path. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Amir Vadai authored
commit 281e8b2f upstream. RdropOvflw counts overrun of HW buffer, therefore should be used for rx_fifo_errors only. Currently RdropOvflw counter is mistakenly also set into rx_missed_errors and rx_over_errors too, which makes the device total dropped packets accounting to show wrong results. Fix that. Use it for rx_fifo_errors only. Fixes: c27a02cd ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC') Signed-off-by:
Amir Vadai <amir@vadai.me> Signed-off-by:
-
Bjørn Mork authored
commit aac8d3c2 upstream. Thomas reports: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05c6 ProdID=6001 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Rainer Weikusat authored
commit a5527dda upstream. The unix_dgram_sendmsg routine use the following test if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) { to determine if sk and other are in an n:1 association (either established via connect or by using sendto to send messages to an unrelated socket identified by address). This isn't correct as the specified address could have been bound to the sending socket itself or because this socket could have been connected to itself by the time of the unix_peer_get but disconnected before the unix_state_lock(other). In both cases, the if-block would be entered despite other == sk which might either block the sender unintentionally or lead to trying to unlock the same spin lock twice for a non-blocking send. Add a other != sk check to guard against this. Fixes: 7d267278 ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By:
Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by:
-
Xin Long authored
commit 7a84bd46 upstream. Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid") corrected the hmacid byte-order when setting a hmacid. but the same issue also exists on getting a hmacid. We fix it by changing hmacids to host order when users get them with getsockopt. Fixes: Commit ed5a377d ("sctp: translate host order to network order when setting a hmacid") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Hans Westgaard Ry authored
commit 5f74f82e upstream. Devices may have limits on the number of fragments in an skb they support. Current codebase uses a constant as maximum for number of fragments one skb can hold and use. When enabling scatter/gather and running traffic with many small messages the codebase uses the maximum number of fragments and may thereby violate the max for certain devices. The patch introduces a global variable as max number of fragments. Signed-off-by:
Hans Westgaard Ry <hans.westgaard.ry@oracle.com> Reviewed-by:
Håkon Bugge <haakon.bugge@oracle.com> Acked-by:
-
Hannes Frederic Sowa authored
commit 415e3d3e upstream. The commit referenced in the Fixes tag incorrectly accounted the number of in-flight fds over a unix domain socket to the original opener of the file-descriptor. This allows another process to arbitrary deplete the original file-openers resource limit for the maximum of open files. Instead the sending processes and its struct cred should be credited. To do so, we add a reference counted struct user_struct pointer to the scm_fp_list and use it to account for the number of inflight unix fds. Fixes: 712f4aad ("unix: properly account for FDs passed over unix sockets") Reported-by:
David Herrmann <dh.herrmann@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Eric Dumazet authored
commit 44c3d0c1 upstream. Silence lockdep false positive about rcu_dereference() being used in the wrong context. First one should use rcu_dereference_protected() as we own the spinlock. Second one should be a normal assignation, as no barrier is needed. Fixes: 18367681 ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.") Reported-by:
Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
-
Hangbin Liu authored
commit 8013d1d7 upstream. Commit 6fd99094 ("ipv6: Don't reduce hop limit for an interface") disabled accept hop limit from RA if it is smaller than the current hop limit for security stuff. But this behavior kind of break the RFC definition. RFC 4861, 6.3.4. Processing Received Router Advertisements A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time, and Retrans Timer) may contain a value denoting that it is unspecified. In such cases, the parameter should be ignored and the host should continue using whatever value it is already using. If the received Cur Hop Limit value is non-zero, the host SHOULD set its CurHopLimit variable to the received value. So add sysctl option accept_ra_min_hop_limit to let user choose the minimum hop limit value they can accept from RA. And set default to 1 to meet RFC standards. Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Acked-by:
YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com> Signed-off-by:
-
Paolo Abeni authored
commit 1cdda918 upstream. Currently, the egress interface index specified via IPV6_PKTINFO is ignored by __ip6_datagram_connect(), so that RFC 3542 section 6.7 can be subverted when the user space application calls connect() before sendmsg(). Fix it by initializing properly flowi6_oif in connect() before performing the route lookup. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
-
Marcelo Ricardo Leitner authored
commit 27f7ed2b upstream. This patch extends commit b93d6471 ("sctp: implement the sender side for SACK-IMMEDIATELY extension") as it didn't white list SCTP_SACK_IMMEDIATELY on sctp_msghdr_parse(), causing it to be understood as an invalid flag and returning -EINVAL to the application. Note that the actual handling of the flag is already there in sctp_datamsg_from_user(). https://tools.ietf.org/html/rfc7053#section-7 Fixes: b93d6471 ("sctp: implement the sender side for SACK-IMMEDIATELY extension") Signed-off-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
commit 9a368aff upstream. Several times already this has been reported as kasan reports caused by syzkaller and trinity and people always looked at RCU races, but it is much more simple. :) In case we bind a pptp socket multiple times, we simply add it to the callid_sock list but don't remove the old binding. Thus the old socket stays in the bucket with unused call_id indexes and doesn't get cleaned up. This causes various forms of kasan reports which were hard to pinpoint. Simply don't allow multiple binds and correct error handling in pptp_bind. Also keep sk_state bits in place in pptp_connect. Fixes: 00959ade ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)") Cc: Dmitry Kozlov <xeb@mail.ru> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Dmitry Vyukov <dvyukov@google.com> Reported-by:
-
Eric Dumazet authored
commit fa0dc04d upstream. Dmitry reported a struct pid leak detected by a syzkaller program. Bug happens in unix_stream_recvmsg() when we break the loop when a signal is pending, without properly releasing scm. Fixes: b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines") Reported-by:
-
Eric Dumazet authored
commit e62a123b upstream. Neal reported crashes with this stack trace : RIP: 0010:[<ffffffff8c57231b>] tcp_v4_send_ack+0x41/0x20f ... CR2: 0000000000000018 CR3: 000000044005c000 CR4: 00000000001427e0 ... [<ffffffff8c57258e>] tcp_v4_reqsk_send_ack+0xa5/0xb4 [<ffffffff8c1a7caa>] tcp_check_req+0x2ea/0x3e0 [<ffffffff8c19e420>] tcp_rcv_state_process+0x850/0x2500 [<ffffffff8c1a6d21>] tcp_v4_do_rcv+0x141/0x330 [<ffffffff8c56cdb2>] sk_backlog_rcv+0x21/0x30 [<ffffffff8c098bbd>] tcp_recvmsg+0x75d/0xf90 [<ffffffff8c0a8700>] inet_recvmsg+0x80/0xa0 [<ffffffff8c17623e>] sock_aio_read+0xee/0x110 [<ffffffff8c066fcf>] do_sync_read+0x6f/0xa0 [<ffffffff8c0673a1>] SyS_read+0x1e1/0x290 [<ffffffff8c5ca262>] system_call_fastpath+0x16/0x1b The problem here is the skb we provide to tcp_v4_send_ack() had to be parked in the backlog of a new TCP fastopen child because this child was owned by the user at the time an out of window packet arrived. Before queuing a packet, TCP has to set skb->dev to NULL as the device could disappear before packet is removed from the queue. Fix this issue by using the net pointer provided by the socket (being a timewait or a request socket). IPv6 is immune to the bug : tcp_v6_send_response() already gets the net pointer from the socket if provided. Fixes: 168a8f58 ("tcp: TCP Fast Open Server - main code path") Reported-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Manfred Rudigier authored
commit 81e8f2e9 upstream. PHY status frames are not reliable, the PHY may not be able to send them during heavy receive traffic. This overflow condition is signaled by the PHY in the next status frame, but the driver did not make use of it. Instead it always reported wrong tx timestamps to user space after an overflow happened because it assigned newly received tx timestamps to old packets in the queue. This commit fixes this issue by clearing the tx timestamp queue every time an overflow happens, so that no timestamps are delivered for overflow packets. This way time stamping will continue correctly after an overflow. Signed-off-by:
Manfred Rudigier <manfred.rudigier@omicron.at> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Ursula Braun authored
commit 52a82e23 upstream. Signed-off-by:
Ursula Braun <ursula.braun@de.ibm.com> Reported-by:
Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com> Signed-off-by:
-
Al Viro authored
commit c80567c8 upstream. ... into returning a positive to path_openat(), which would interpret that as "symlink had been encountered" and proceed to corrupt memory, etc. It can only happen due to a bug in some ->open() instance or in some LSM hook, etc., so we report any such event *and* make sure it doesn't trick us into further unpleasantness. Signed-off-by:
-
Mikulas Patocka authored
commit b6853f78 upstream. The delete opration can allocate additional space on the HPFS filesystem due to btree split. The HPFS driver checks in advance if there is available space, so that it won't corrupt the btree if we run out of space during splitting. If there is not enough available space, the HPFS driver attempted to truncate the file, but this results in a deadlock since the commit 7dd29d8d ("HPFS: Introduce a global mutex and lock it on every callback from VFS"). This patch removes the code that tries to truncate the file and -ENOSPC is returned instead. If the user hits -ENOSPC on delete, he should try to delete other files (that are stored in a leaf btree node), so that the delete operation will make some space for deleting the file stored in non-leaf btree node. Reported-by:
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Signed-off-by:
-
Mike Krinkin authored
commit 17e4bce0 upstream. Ubsan reports the following warning due to a typo in update_accessed_dirty_bits template, the patch fixes the typo: [ 168.791851] ================================================================================ [ 168.791862] UBSAN: Undefined behaviour in arch/x86/kvm/paging_tmpl.h:252:15 [ 168.791866] index 4 is out of range for type 'u64 [4]' [ 168.791871] CPU: 0 PID: 2950 Comm: qemu-system-x86 Tainted: G O L 4.5.0-rc5-next-20160222 #7 [ 168.791873] Hardware name: LENOVO 23205NG/23205NG, BIOS G2ET95WW (2.55 ) 07/09/2013 [ 168.791876] 0000000000000000 ffff8801cfcaf208 ffffffff81c9f780 0000000041b58ab3 [ 168.791882] ffffffff82eb2cc1 ffffffff81c9f6b4 ffff8801cfcaf230 ffff8801cfcaf1e0 [ 168.791886] 0000000000000004 0000000000000001 0000000000000000 ffffffffa1981600 [ 168.791891] Call Trace: [ 168.791899] [<ffffffff81c9f780>] dump_stack+0xcc/0x12c [ 168.791904] [<ffffffff81c9f6b4>] ? _atomic_dec_and_lock+0xc4/0xc4 [ 168.791910] [<ffffffff81da9e81>] ubsan_epilogue+0xd/0x8a [ 168.791914] [<ffffffff81daafa2>] __ubsan_handle_out_of_bounds+0x15c/0x1a3 [ 168.791918] [<ffffffff81daae46>] ? __ubsan_handle_shift_out_of_bounds+0x2bd/0x2bd [ 168.791922] [<ffffffff811287ef>] ? get_user_pages_fast+0x2bf/0x360 [ 168.791954] [<ffffffffa1794050>] ? kvm_largepages_enabled+0x30/0x30 [kvm] [ 168.791958] [<ffffffff81128530>] ? __get_user_pages_fast+0x360/0x360 [ 168.791987] [<ffffffffa181b818>] paging64_walk_addr_generic+0x1b28/0x2600 [kvm] [ 168.792014] [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm] [ 168.792019] [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350 [ 168.792044] [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm] [ 168.792076] [<ffffffffa181c36d>] paging64_gva_to_gpa+0x7d/0x110 [kvm] [ 168.792121] [<ffffffffa181c2f0>] ? paging64_walk_addr_generic+0x2600/0x2600 [kvm] [ 168.792130] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792178] [<ffffffffa17d9a4a>] emulator_read_write_onepage+0x27a/0x1150 [kvm] [ 168.792208] [<ffffffffa1794d44>] ? __kvm_read_guest_page+0x54/0x70 [kvm] [ 168.792234] [<ffffffffa17d97d0>] ? kvm_task_switch+0x160/0x160 [kvm] [ 168.792238] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792263] [<ffffffffa17daa07>] emulator_read_write+0xe7/0x6d0 [kvm] [ 168.792290] [<ffffffffa183b620>] ? em_cr_write+0x230/0x230 [kvm] [ 168.792314] [<ffffffffa17db005>] emulator_write_emulated+0x15/0x20 [kvm] [ 168.792340] [<ffffffffa18465f8>] segmented_write+0xf8/0x130 [kvm] [ 168.792367] [<ffffffffa1846500>] ? em_lgdt+0x20/0x20 [kvm] [ 168.792374] [<ffffffffa14db512>] ? vmx_read_guest_seg_ar+0x42/0x1e0 [kvm_intel] [ 168.792400] [<ffffffffa1846d82>] writeback+0x3f2/0x700 [kvm] [ 168.792424] [<ffffffffa1846990>] ? em_sidt+0xa0/0xa0 [kvm] [ 168.792449] [<ffffffffa185554d>] ? x86_decode_insn+0x1b3d/0x4f70 [kvm] [ 168.792474] [<ffffffffa1859032>] x86_emulate_insn+0x572/0x3010 [kvm] [ 168.792499] [<ffffffffa17e71dd>] x86_emulate_instruction+0x3bd/0x2110 [kvm] [ 168.792524] [<ffffffffa17e6e20>] ? reexecute_instruction.part.110+0x2e0/0x2e0 [kvm] [ 168.792532] [<ffffffffa14e9a81>] handle_ept_misconfig+0x61/0x460 [kvm_intel] [ 168.792539] [<ffffffffa14e9a20>] ? handle_pause+0x450/0x450 [kvm_intel] [ 168.792546] [<ffffffffa15130ea>] vmx_handle_exit+0xd6a/0x1ad0 [kvm_intel] [ 168.792572] [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm] [ 168.792597] [<ffffffffa17f6bcd>] kvm_arch_vcpu_ioctl_run+0xd3d/0x6090 [kvm] [ 168.792621] [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm] [ 168.792627] [<ffffffff8293b530>] ? __ww_mutex_lock_interruptible+0x1630/0x1630 [ 168.792651] [<ffffffffa17f5e90>] ? kvm_arch_vcpu_runnable+0x4f0/0x4f0 [kvm] [ 168.792656] [<ffffffff811eeb30>] ? preempt_notifier_unregister+0x190/0x190 [ 168.792681] [<ffffffffa17e0447>] ? kvm_arch_vcpu_load+0x127/0x650 [kvm] [ 168.792704] [<ffffffffa178e9a3>] kvm_vcpu_ioctl+0x553/0xda0 [kvm] [ 168.792727] [<ffffffffa178e450>] ? vcpu_put+0x40/0x40 [kvm] [ 168.792732] [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350 [ 168.792735] [<ffffffff82946087>] ? _raw_spin_unlock+0x27/0x40 [ 168.792740] [<ffffffff8163a943>] ? handle_mm_fault+0x1673/0x2e40 [ 168.792744] [<ffffffff8129daa8>] ? trace_hardirqs_on_caller+0x478/0x6c0 [ 168.792747] [<ffffffff8129dcfd>] ? trace_hardirqs_on+0xd/0x10 [ 168.792751] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792756] [<ffffffff81725a80>] do_vfs_ioctl+0x1b0/0x12b0 [ 168.792759] [<ffffffff817258d0>] ? ioctl_preallocate+0x210/0x210 [ 168.792763] [<ffffffff8174aef3>] ? __fget+0x273/0x4a0 [ 168.792766] [<ffffffff8174acd0>] ? __fget+0x50/0x4a0 [ 168.792770] [<ffffffff8174b1f6>] ? __fget_light+0x96/0x2b0 [ 168.792773] [<ffffffff81726bf9>] SyS_ioctl+0x79/0x90 [ 168.792777] [<ffffffff82946880>] entry_SYSCALL_64_fastpath+0x23/0xc1 [ 168.792780] ================================================================================ Signed-off-by:
Mike Krinkin <krinkin.m.u@gmail.com> Reviewed-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Ilya Dryomov authored
commit e7a88e82 upstream. The contract between try_read() and try_write() is that when called each processes as much data as possible. When instructed by osd_client to skip a message, try_read() is violating this contract by returning after receiving and discarding a single message instead of checking for more. try_write() then gets a chance to write out more requests, generating more replies/skips for try_read() to handle, forcing the messenger into a starvation loop. Reported-by:
Varada Kari <Varada.Kari@sandisk.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Tested-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit d045437a upstream. The ftrace:function event is only displayed for parsing the function tracer data. It is not used to enable function tracing, and does not include an "enable" file in its event directory. Originally, this event was kept separate from other events because it did not have a ->reg parameter. But perf added a "reg" parameter for its use which caused issues, because it made the event available to functions where it was not compatible for. Commit 9b63776f "tracing: Do not enable function event with enable" added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event from being enabled by normal trace events. But this commit missed keeping the function event from being displayed by the "available_events" directory, which is used to show what events can be enabled by set_event. One documented way to enable all events is to: cat available_events > set_event But because the function event is displayed in the available_events, this now causes an INVALID error: cat: write error: Invalid argument Reported-by:
Chunyu Hu <chuhu@redhat.com> Fixes: 9b63776f "tracing: Do not enable function event with enable" Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Christian Borntraeger authored
commit d7444794 upstream. In async_pf we try to allocate with NOWAIT to get an element quickly or fail. This code also handle failures gracefully. Lets silence potential page allocation failures under load. qemu-system-s39: page allocation failure: order:0,mode:0x2200000 [...] Call Trace: ([<00000000001146b8>] show_trace+0xf8/0x148) [<000000000011476a>] show_stack+0x62/0xe8 [<00000000004a36b8>] dump_stack+0x70/0x98 [<0000000000272c3a>] warn_alloc_failed+0xd2/0x148 [<000000000027709e>] __alloc_pages_nodemask+0x94e/0xb38 [<00000000002cd36a>] new_slab+0x382/0x400 [<00000000002cf7ac>] ___slab_alloc.constprop.30+0x2dc/0x378 [<00000000002d03d0>] kmem_cache_alloc+0x160/0x1d0 [<0000000000133db4>] kvm_setup_async_pf+0x6c/0x198 [<000000000013dee8>] kvm_arch_vcpu_ioctl_run+0xd48/0xd58 [<000000000012fcaa>] kvm_vcpu_ioctl+0x372/0x690 [<00000000002f66f6>] do_vfs_ioctl+0x3be/0x510 [<00000000002f68ec>] SyS_ioctl+0xa4/0xb8 [<0000000000781c5e>] system_call+0xd6/0x264 [<000003ffa24fa06a>] 0x3ffa24fa06a Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Signed-off-by:
-
Stefan Hajnoczi authored
commit b7052cd7 upstream. The qword_get() function NUL-terminates its output buffer. If the input string is in hex format \xXXXX... and the same length as the output buffer, there is an off-by-one: int qword_get(char **bpp, char *dest, int bufsize) { ... while (len < bufsize) { ... *dest++ = (h << 4) | l; len++; } ... *dest = '\0'; return len; } This patch ensures the NUL terminator doesn't fall outside the output buffer. Signed-off-by:
Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Gerhard Uttenthaler authored
commit 90cfde46 upstream. This patch fixes the problem that more CAN messages could be sent to the interface as could be send on the CAN bus. This was more likely for slow baud rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under heavy TX load this produced another bulk transfer without checking the free_slots variable and hence caused the overflow in the interface. Signed-off-by:
Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Lisa Du authored
commit 7a64cd88 upstream. There's one point was missed in the patch commit da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes."). When configure BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of void * is 64bit on 64bit system. Correct it here. Signed-off-by:
Lisa Du <cldu@marvell.com> Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Fixes: da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes.") Acked-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Simon Guinot authored
commit 59ceeaaf upstream. In __request_region, if a conflict with a BUSY and MUXED resource is detected, then the caller goes to sleep and waits for the resource to be released. A pointer on the conflicting resource is kept. At wake-up this pointer is used as a parent to retry to request the region. A first problem is that this pointer might well be invalid (if for example the conflicting resource have already been freed). Another problem is that the next call to __request_region() fails to detect a remaining conflict. The previously conflicting resource is passed as a parameter and __request_region() will look for a conflict among the children of this resource and not at the resource itself. It is likely to succeed anyway, even if there is still a conflict. Instead, the parent of the conflicting resource should be passed to __request_region(). As a fix, this patch doesn't update the parent resource pointer in the case we have to wait for a muxed region right after. Reported-and-tested-by:
Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by:
Simon Guinot <simon.guinot@sequanux.org> Tested-by:
Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by:
-
Jan Kara authored
commit 74dae427 upstream. Competing overwrite DIO in dioread_nolock mode will just overwrite pointer to io_end in the inode. This may result in data corruption or extent conversion happening from IO completion interrupt because we don't properly set buffer_defer_completion() when unlocked DIO races with locked DIO to unwritten extent. Since unlocked DIO doesn't need io_end for anything, just avoid allocating it and corrupting pointer from inode for locked DIO. A cleaner fix would be to avoid these games with io_end pointer from the inode but that requires more intrusive changes so we leave that for later. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
