Convert the messages in this function to dev_err().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code that would disable the irq after getting a number of D/A errors
is disabled. Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This blank line message is not needed. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this printk message into a dev_err().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These messages are just added noise. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An irq is only needed by this driver in order to support async commands.
Since it is optional, modify the attach so that if the request_irq() fails
the attach does not fail.

Remove the printk noise about the irq.

Only hookup the async command support if the request_irq() was successful.

Also, only call dt282x_grab_dma() if we have an irq since interrupt support
is needed to support dma.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These messages don't appear to be important enough to warrent KERN_INFO
and KERN_WARNING levels. Convert them dev_dbg().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert the printk(KERN_WARNING messages in this function to dev_dbg().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An irq is only needed by this driver in order to support async commands.
Since it is optional, modify the attach so that if the request_irq() fails
the attach does not fail.

Remove the printk noise about the irq.

Only hookup the async command support if the request_irq() was successful.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this printk message into a dev_dev().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This printk could spew a lot of noise while waiting for the ai conversion
to complete. Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ai read timeout will return -ETIMEDOUT. The printk is just added
noise. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The interrupt support in this driver is incomplete due to the missing
comedi functions to support async commands.

Since the interrupt code is already disable just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function is not used by the driver. It's also suffering from bitrot
since COMEDI_MDEMAND and COMEDI_MCONTS are not defined anywhere. Just
remove the code.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert all the printk() messages in this driver to dev_dbg().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This printk is just added noise. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code that checks the DT_S_READY status is disabled. Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert this printk message to a dev_err() message.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An irq is only needed by this driver in order to support async commands.
Since it is optional, modify the attach so that if the request_irq() fails
the attach does not fail.

Remove the printk noise about the irq.

Only hookup the async command support if the request_irq() was successful.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These printk messages are just added noise. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A timeout will return -ETIMEDOUT. The printks are just added noise.
Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An irq is only needed by this driver in order to support async commands.
Since it is optional, modify the attach so that if an invalid irq is
selected by the user, or the request_irq() fails, the attach does not
fail.

Remove all the printk noise about the irq.

Only hookup the async command support if the request_irq() was successful.

Tidy up das16m1_irq_bits() a bit. This helper returns the value that needs
to be written to the DAS16M1_INTR_CONTROL register to setup the irq routing.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ai read timeout will return -ETIMEDOUT. The printk is just added
noise. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver does not have interrupt support. Remove the commented out
code that requests the irq.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These commented out messages are just added noise. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code to initialize subdevice[2] is commented out and incomplete.
Just remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the commented out message, it would just be added noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert these messages to dev_dbg() and tidy them up a bit.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert these warning messages to dev_dbg() to minimize the noise.
Also, tidy them up a bit.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert these debug messages to dev_dbg() and tidy them up a bit.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The "success" message after an attach is just added noise. Remove it.

The normal return value for "success" is 0.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert these debug messages to dev_dbg().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An allocation failure will have already displayed a message.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Line 921: Removed the space before the semicolon.
Signed-off-by: Aldo Iljazi <mail@aldo.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: staging: ft1000: ft1000-usb: ft1000_debug.c: check return value of get_user() in ft1000_ioctl()

get_user() may fail and cause 'msgsz' uninitialized, so need give a
check. The related warning (with allmodconfig under hexagon):

    CC [M]  drivers/staging/ft1000/ft1000-usb/ft1000_debug.o
  drivers/staging/ft1000/ft1000-usb/ft1000_debug.c: In function 'ft1000_ioctl':
  include/uapi/linux/swab.h:53:9: warning: 'msgsz' may be used uninitialized in this function [-Wuninitialized]
  drivers/staging/ft1000/ft1000-usb/ft1000_debug.c:533:17: note: 'msgsz' was declared here
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The rest of the code seem to imply that rmf_dumper may indeed be
NULL.  Change the code so that dumping is not even considered if
rmf_dumper callback is not set.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bus_info field of struct ethtool_drvinfo is an array thus it always
evaluates to true in a boolean context.  Therefore operation
depending on it being false will never be executed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed the following coding style issues:

Lines 66-70: Replaced spaced with tabs.
Lines 75, 98, 182: Inserted space before the open parenthesis.
Line 89: Inserted spaces around that '='
Signed-off-by: Aldo Iljazi <mail@aldo.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix to return -ENOMEM instead of 0 when the memory alloc fail
in probe error handling path.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed a coding style issue, specifically:

Line 1798: Removed parentheses since return is not a function.
Signed-off-by: Aldo Iljazi <mail@aldo.io>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>