Fix the format string for serio device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the format string for input device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's automatically set EV_ABS bit in device's event type list when calling
input_set_abs_params() so that drivers do not have to do it explicitly.

These calls are never in a hot paths so we won't lose much time by setting
the same bit several times.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In case we start with the device not fully quiesced we should make sure we
cancel the workqueue after freeing interrupt.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change switch to managed resources to simplifies error handling
and module unloading and does away with platform_driver remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 'max' size passed into the function is measured in number of bits
(KEY_MAX, LED_MAX, etc) so we need to convert it accordingly before trying
to copy the data out, otherwise we will try copying too much and end up
with up with a page fault.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

ACPI device enumeration mechanism changed a lot since 3.16-rc1.
ACPI device objects with _HID will be enumerated to platform bus by default.
For the existing PNP drivers that probe the PNPACPI devices, the device ids
are listed explicitly in drivers/acpi/acpi_pnp.c.
But ACPI folks will continue their effort on shrinking this id list by
converting the PNP drivers to platform drivers, for the devices that don't
belong to PNP bus in nature.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Follow the license string convention indicated in include/linux/module.h
(don't capitalize v).

This fixes following randconfig warning:
FATAL: modpost: GPL-incompatible module palmas-pwrbutton.ko uses GPL-only symbol 'platform_driver_unregister'

Fixes: adff5962 ("Input: introduce palmas-pwrbutton")
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

make C=2 CHECK="scripts/coccicheck" MODE=report COCCI=scripts/coccinelle/misc/irqf_oneshot.cocci ./drivers/input/misc/palmas-pwrbutton.o
Reports:
drivers/input/misc/palmas-pwrbutton.c:213:9-29: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT

Palmas power button just needs threaded IRQ handler since I2C operations
are involved and there is nothing in non-threaded primary handler we could
do.

So mark the request with ONESHOT as it should have been done in these
cases.

Fixes: adff5962 ("Input: introduce palmas-pwrbutton")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Asus X450 and X550 laptops use a PS/2 touchpad from a new
manufacturer called FocalTech:

https://bugzilla.kernel.org/show_bug.cgi?id=77391
https://bugzilla.redhat.com/show_bug.cgi?id=1110011

The protocol for these devices is not known at this time, but even
without knowing the protocol they need some special handling. They get
upset by some of our other PS/2 device probing, and once upset generate
random mouse events making things unusable even with an external mouse.

This patch adds detection of these devices based on their pnp ids, and
when they are detected, treats them as a bare ps/2 mouse. Doing things
this way they at least work in their ps/2 mouse emulation mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The matches_pnp_id function from the synaptics driver is useful for other
drivers too. Make it a generic psmouse helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current codes in gameport and analog joystick drivers for the time
accounting have a long-standing problem when the system is running
with CPU freq; since the timing is measured via TSC or sample counter,
the calculation isn't reliable.

In this patch, as a simple fix, use the standard ktime to measure the
timing.  In case where no high resolution timer is available,
use_ktime bool option is provided to both modules.  Setting
use_ktime=false switches to the old methods.
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver to supports the haptic controller on MAX77693 Multifunction
device with PMIC, CHARGER, LED, MUIC, HAPTIC.

This driver supports external pwm and LRA (Linear Resonant Actuator) motor.
User can control the haptic device via force feedback framework.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Many palmas family of PMICs have support for interrupt based power button.
This allows the device to notify the processor of external push button
events over the shared palmas interrupt. However, this event is generated
only during a "press" operation. Software is supposed to poll(sigh!) for
detecting a release event.

The PMIC also supports ability to power off independent of the software
decisions when the button is pressed for a long duration if the PMIC is
appropriately configured on the platform.

Even though the function is similar to twl4030_pwrbutton, it is
substantially different in operation to belong to a new driver of it's own.

Based on original work done by Girish S Ghongdemath <girishsg@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Adding support for the DRV2667 haptic driver.  This device has the ability
to store vibration patterns in RAM and execute them once the GO bit is set.

The initial driver sets a basic waveform in the first waveform sequence and
will play the waveform when the GO bit is set and will continously play the
waveform until the GO bit is unset.

Data sheet is here: http://www.ti.com/product/drv2667Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The userspace xboxdrv driver knows some more device ids than the kernel.
This patch adds the missing xbox gamepads from [1] to xpad.c

[1] https://github.com/Grumbel/xboxdrv/blob/master/src/xpad_device.cppSigned-off-by: Benjamin Valentin <benpicco@zedat.fu-berlin.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The xpad driver recognizes Razer Sabertooth controllers as generic xbox
controller, while it is really a 360 controller.  This patch adds pid/vid
mappings for the controller so that it is correctly recognized.
Signed-off-by: Frank Razenberg <frank@zzattack.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Previous algorithm was a bit conservative and complicating with respect to
identifying key ghosting.  This CL uses the bitops hamming weight function
(hweight8) to count the number of matching rows for colM & colN.  If that
number is > 1 ghosting is present.

Additionally it removes NULL keys and our one virtual keypress KEY_BATTERY
from consideration as these inputs are never physical keypresses.
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Luigi Semenzato <semenzato@chromium.org>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync with mainline to bring in Chrome EC changes.

Pull Xtensa updates from Chris Zankel:
 "Xtensa improvements for 3.17:
   - support highmem on cores with aliasing data cache.  Enable highmem
     on kc705 by default
   - simplify addition of new core variants (no need to modify Kconfig /
     Makefiles)
   - improve robustness of unaligned access handler and its interaction
     with window overflow/underflow exception handlers
   - deprecate atomic and spill registers syscalls
   - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
     statements
   - wire up renameat2 syscall.

  Various fixes:
   - fix address checks in dma_{alloc,free}_coherent (runtime BUG)
   - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
   - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
     (runtime unrecoverable exception)
   - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
     register clobbering)
   - fix kernel/user jump out of fast_unaligned (potential runtime
     unrecoverabl exception)
   - replace termios IOCTL code definitions with constants (userspace
     build breakage)"

* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
  xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
  xtensa: don't allow overflow/underflow on unaligned stack
  xtensa: fix a6 and a7 handling in fast_syscall_xtensa
  xtensa: allow single-stepping through unaligned load/store
  xtensa: move invalid unaligned instruction handler closer to its users
  xtensa: make fast_unaligned store restartable
  xtensa: add double exception fixup handler for fast_unaligned
  xtensa: fix kernel/user jump out of fast_unaligned
  xtensa: configure kc705 for highmem
  xtensa: support highmem in aliasing cache flushing code
  xtensa: support aliasing cache in kmap
  xtensa: support aliasing cache in k[un]map_atomic
  xtensa: implement clear_user_highpage and copy_user_highpage
  xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
  xtensa: allow fixmap and kmap span more than one page table
  xtensa: make fixmap region addressing grow with index
  xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
  xtensa: add renameat2 syscall
  xtensa: fix address checks in dma_{alloc,free}_coherent
  xtensa: replace IOCTL code definitions with constants
  ...

unicore32 builds fail with

  arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
  arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
  arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
  arch/unicore32/kernel/signal.c: In function ‘do_signal’:
  arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
  make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
  make: *** [arch/unicore32/kernel/signal.o] Error 2

Bisect points to commit 649671c9 ("unicore32: Use get_signal()
signal_setup_done()").

This code never even compiled.  Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up.  Compile
tested only.

Fixes: 649671c9 ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations

Pull ARM SoC fixes from Olof Johansson:
 "Here's the weekly batch of fixes from arm-soc.

  The delta is a largeish negative delta, due to revert of SMP support
  for Broadcom's STB SoC -- it was accidentally merged before some
  issues had been addressed, so they will make a new attempt for 3.18.
  I didn't see a need for a full revert of the whole platform due to
  this, we're keeping the rest enabled.

  The rest is mostly:

   - a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
   - some MTD/NAND fixes for OMAP
   - minor DT fixes for shmobile
   - warning fix for UP builds on vexpress/spc

  There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
  so it can boot.  Drivers and the rest had landed for 3.17, and it's
  small and isolated so it made sense to pick up now even if it's not a
  bugfix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  vexpress/spc: fix a build warning on array bounds
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
  MAINTAINERS: catch special Rockchip code locations
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: brcmstb: revert SMP support
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ...

With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:

Add basic subarchitecture support for the DRA72x and DRA74x.  These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
platforms.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/

* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull spi bugfixes from Mark Brown:
 "A smattering of bug fixes for the SPI subsystem, all in driver code
  which has seen active work recently and none of them with any great
  global impact.

  There's also a new ACPI ID for the pxa2xx driver which required no
  code changes and the addition of kerneldoc for some structure fields
  that were missing it and generating warnings during documentation
  builds as a result"

* tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sh-msiof: Fix transmit-only DMA transfers
  spi/rockchip: Avoid accidentally turning off the clock
  spi: dw: fix kernel crash due to NULL pointer dereference
  spi: dw-pci: fix bug when regs left uninitialized
  spi: davinci: fix SPI_NO_CS functionality
  spi/rockchip: fixup incorrect dma direction setting
  spi/pxa2xx: Add ACPI ID for Intel Braswell
  spi: spi-au1550: fix build failure
  spi: rspi: Fix leaking of unused DMA descriptors
  spi: sh-msiof: Fix leaking of unused DMA descriptors
  spi: Add missing kerneldoc bits
  spi/omap-mcspi: Fix the spi task hangs waiting dma_rx

spi: Bug fixes for v3.17

A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.

There's also a new ACPI ID for the pxa2xx driver which required no code
changes and the addition of kerneldoc for some structure fields that
were missing it and generating warnings during documentation builds as a
result.

# gpg: Signature made Sun 31 Aug 2014 13:19:12 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Fix tx/rx mixup, which broke transmit-only transfers.

Introduced by commit 4240305f7cbdc7782aa8bc40cc702775d9ac0839
("spi: sh-msiof: Fix leaking of unused DMA descriptors").
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull file locking bugfx from Jeff Layton:
 "Just a bugfix for a bug that crept in to v3.15.  It's in a rather rare
  error path, and I'm not aware of anyone having hit it, but it's worth
  fixing for v3.17"

* tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux:
  locks: pass correct "before" pointer to locks_unlink_lock in generic_add_lease

Merge remote-tracking branches 'spi/fix/au1550', 'spi/fix/davinci', 'spi/fix/doc', 'spi/fix/dw', 'spi/fix/omap-mcspi', 'spi/fix/pxa2xx', 'spi/fix/rockchip' and 'spi/fix/rspi' into spi-linus

Pull x86 fixes from Peter Anvin:
 "One patch to avoid assigning interrupts we don't actually have on
  non-PC platforms, and two patches that addresses bugs in the new
  IOAPIC assignment code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, irq, PCI: Keep IRQ assignment for runtime power management
  x86: irq: Fix bug in setting IOAPIC pin attributes
  x86: Fix non-PC platform kernel crash on boot due to NULL dereference

Pull ACPI and power management fixes from Rafael Wysocki:

 - Fix for an ACPI regression related to the handling of fixed events
   that caused netlink routines to be (incorrectly) run in interrupt
   context from Lan Tianyu

 - Fix for an ACPI EC driver regression on Acer Aspire V5-573G that
   caused AC/battery plug/unplug and video brightness change
   notifications to be delayed on that machine from Lv Zheng

 - Fix for an ACPI device enumeration regression that caused ACPI driver
   probe to fail for some devices where it succeeded before (Rafael J
   Wysocki)

 - intel_pstate driver fix to prevent it from printing an information
   message for every CPU in the system on every boot from Andi Kleen

 - s5pv210 cpufreq driver fix to remove an __init annotation from a
   routine that in fact can be called at any time after init too from
   Mark Brown

 - New Intel Braswell device ID for the ACPI LPSS (Low-Power Subsystem)
   driver from Alan Cox

 - New Intel Braswell CPU ID for intel_pstate from Mika Westerberg

* tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: s5pv210: Remove spurious __init annotation
  cpufreq: intel_pstate: Add CPU ID for Braswell processor
  intel_pstate: Turn per cpu printk into pr_debug
  ACPI / LPSS: Add ACPI IDs for Intel Braswell
  ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
  ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
  ACPI: Run fixed event device notifications in process context
  ACPI / scan: Allow ACPI drivers to bind to PNP device objects

Merge patches from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  kexec: purgatory: add clean-up for purgatory directory
  Documentation/kdump/kdump.txt: add ARM description
  flush_icache_range: export symbol to fix build errors
  tools: selftests: fix build issue with make kselftests target
  ocfs2: quorum: add a log for node not fenced
  ocfs2: o2net: set tcp user timeout to max value
  ocfs2: o2net: don't shutdown connection when idle timeout
  ocfs2: do not write error flag to user structure we cannot copy from/to
  x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
  drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
  xattr: fix check for simultaneous glibc header inclusion
  kexec: remove CONFIG_KEXEC dependency on crypto
  kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
  x86,mm: fix pte_special versus pte_numa
  hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
  mm/zpool: use prefixed module loading
  zram: fix incorrect stat with failed_reads
  lib: turn CONFIG_STACKTRACE into an actual option.
  mm: actually clear pmd_numa before invalidating
  memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
  ...

Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add arm specific parts to kdump kernel documentation.
Signed-off-by: Hu Keping <hukeping@huawei.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix building errors occuring due to a missing export of
flush_icache_range() in

kisskb.ellerman.id.au/kisskb/buildresult/11677809/

ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined!
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>	[arc]
Acked-by: Richard Kuo <rkuo@codeaurora.org>	[hexagon]
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>	[xtensa]
Cc: Noam Camus <noamc@ezchip.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Zhigang Lu <zlu@tilera.com>		[tile]
Cc: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the typo of ARCH when running 'make kselftests'.  Change the 'X86'
to 'x86'.  Test by compilation.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>