Potentially overflowing expression 1000000 * data->timeout_clks with
type unsigned int is evaluated using 32-bit arithmetic, and then used
in a context that expects an expression of type unsigned long long.

To avoid overflow, cast 1000000U to type unsigned long long.
Special thanks to Coverity.

Fixes: 7f05538a ("mmc: sdhci: fix data timeout (part 2)")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

- The DMA error interrupt bit is in a different position as
   compared to the sdhci standard.  This is accounted for in
   many cases, but not handled in the case of clearing the
   INT_STATUS register by writing a 1 to that location.
 - The HOST_CONTROL register is very different as compared to
   the sdhci standard.  This is accounted for in the write
   case, but not when read back out (which it is in the sdhci
   code).
Signed-off-by: Dave Russell <david.russell@datasoft.com>
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some Intel controllers (e.g. BXT) might fail to set bus power after a
D3 -> D0 transition due to the present state not yet having propagated.
Retry for up to 2 milliseconds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Let devices define their own sdhci_ops so that device-specific variations
can be implemented without adding quirks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Multi-block data transfers can specify the number of blocks either using a
Set Block Count command (CMD23) or by sending a STOP command (CMD12) after
the required number of blocks has transferred. CMD23 is preferred, but some
cards don't support it. CMD12 with R1b response is used for writes, and
R1 response for reads.

Some SDHCI host controllers give a Transfer Complete (TC) interrupt for the
STOP command (CMD12) whether or not a R1b response has been specified. The
quirk SDHCI_QUIRK2_STOP_WITH_TC identifies those host controllers, but the
implementation only considers the case where the TC interrupt arrives at
the same time as the Command Complete (CC) interrupt. However,
occasionally TC arrives before CC. That is harmless, but does generate an
error message "Got data interrupt 0x00000002 even though no data operation
was in progress".

A simpler approach is to force R1b response onto all STOP commands, because
SDHCI will handle TC before CC in the general case, so do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Commit f68381a7 (mmc: block: fix packed command header endianness)
correctly fixed endianness handling of packed_cmd_hdr in
mmc_blk_packed_hdr_wrq_prep.

But now, sparse complains about incorrect types:
drivers/mmc/card/block.c:1613:27: sparse: incorrect type in assignment (different base types)
drivers/mmc/card/block.c:1613:27:    expected unsigned int [unsigned] [usertype] <noident>
drivers/mmc/card/block.c:1613:27:    got restricted __le32 [usertype] <noident>
...

So annotate cmd_hdr properly using __le32 to make everyone happy.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: f68381a7 (mmc: block: fix packed command header endianness)
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Per the vendor's requirement, we shouldn't do any setting for
1.8V Signaling Enable, otherwise the interaction/behaviour between
phy and controller will be undefined. Mostly it works fine if we do
that, but we still see failures. Anyway, let's fix it to meet the
vendor's requirement. The error log looks like:

 [   93.405085] mmc1: unexpected status 0x800900 after switch
 [   93.408474] mmc1: switch to bus width 1 failed
 [   93.408482] mmc1: mmc_select_hs200 failed, error -110
 [   93.408492] mmc1: error -110 during resume (card was removed?)
 [   93.408705] PM: resume of devices complete after 213.453 msecs
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Per JESD84-B51 P49, Host need to change frequency to <=52MHz
after setting HS_TIMING to 0x1, and host may changes frequency
to <= 200MHz after setting HS_TIMING to 0x3. That means the card
expects the clock rate to increase from the current used f_init
(which is less than 400KHz, but still being less than 52MHz) to
52MHz, otherwise we find some eMMC devices significantly report
failure when sending status.
Reported-by: Xiao Yao <xiaoyao@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When introducing hs400es, I didn't notice that we haven't
switched voltage to 1V2 or 1V8 for it. That happens to work
as the first controller claiming to support hs400es, arasan(5.1),
which is designed to only support 1V8. So the voltage is fixed to 1V8.
But it actually is wrong, and will not fit for other host controllers.
Let's fix it.

Fixes: commit 81ac2af6 ("mmc: core: implement enhanced strobe support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We get 1 warning when building kernel with W=1:
drivers/mmc/card/block.c:2147:5: warning: no previous prototype for
'mmc_blk_issue_rq' [-Wmissing-prototypes]

In fact, this function is declared in drivers/mmc/card/block.h, so this
patch adds missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fixes the following sparse warning:

drivers/mmc/host/sdhci-of-arasan.c:253:6: warning:
 symbol 'sdhci_arasan_reset' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull blk-mq CPU hotplug update from Jens Axboe:
 "This is the conversion of blk-mq to the new hotplug state machine"

* 'for-4.9/block-smp' of git://git.kernel.dk/linux-block:
  blk-mq: fixup "Convert to new hotplug state machine"
  blk-mq: Convert to new hotplug state machine
  blk-mq/cpu-notif: Convert to new hotplug state machine

Pull blk-mq irq/cpu mapping updates from Jens Axboe:
 "This is the block-irq topic branch for 4.9-rc. It's mostly from
  Christoph, and it allows drivers to specify their own mappings, and
  more importantly, to share the blk-mq mappings with the IRQ affinity
  mappings. It's a good step towards making this work better out of the
  box"

* 'for-4.9/block-irq' of git://git.kernel.dk/linux-block:
  blk_mq: linux/blk-mq.h does not include all the headers it depends on
  blk-mq: kill unused blk_mq_create_mq_map()
  blk-mq: get rid of the cpumask in struct blk_mq_tags
  nvme: remove the post_scan callout
  nvme: switch to use pci_alloc_irq_vectors
  blk-mq: provide a default queue mapping for PCI device
  blk-mq: allow the driver to pass in a queue mapping
  blk-mq: remove ->map_queue
  blk-mq: only allocate a single mq_map per tag_set
  blk-mq: don't redistribute hardware queues on a CPU hotplug event

Pull device mapper updates from Mike Snitzer:

 - various fixes and cleanups for request-based DM core

 - add support for delaying the requeue of requests; used by DM
   multipath when all paths have failed and 'queue_if_no_path' is
   enabled

 - DM cache improvements to speedup the loading metadata and the writing
   of the hint array

 - fix potential for a dm-crypt crash on device teardown

 - remove dm_bufio_cond_resched() and just using cond_resched()

 - change DM multipath to return a reservation conflict error
   immediately; rather than failing the path and retrying (potentially
   indefinitely)

* tag 'dm-4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (24 commits)
  dm mpath: always return reservation conflict without failing over
  dm bufio: remove dm_bufio_cond_resched()
  dm crypt: fix crash on exit
  dm cache metadata: switch to using the new cursor api for loading metadata
  dm array: introduce cursor api
  dm btree: introduce cursor api
  dm cache policy smq: distribute entries to random levels when switching to smq
  dm cache: speed up writing of the hint array
  dm array: add dm_array_new()
  dm mpath: delay the requeue of blk-mq requests while all paths down
  dm mpath: use dm_mq_kick_requeue_list()
  dm rq: introduce dm_mq_kick_requeue_list()
  dm rq: reduce arguments passed to map_request() and dm_requeue_original_request()
  dm rq: add DM_MAPIO_DELAY_REQUEUE to delay requeue of blk-mq requests
  dm: convert wait loops to use autoremove_wake_function()
  dm: use signal_pending_state() in dm_wait_for_completion()
  dm: rename task state function arguments
  dm: add two lockdep_assert_held() statements
  dm rq: simplify dm_old_stop_queue()
  dm mpath: check if path's request_queue is dying in activate_path()
  ...

Pull main rdma updates from Doug Ledford:
 "This is the main pull request for the rdma stack this release.  The
  code has been through 0day and I had it tagged for linux-next testing
  for a couple days.

  Summary:

   - updates to mlx5

   - updates to mlx4 (two conflicts, both minor and easily resolved)

   - updates to iw_cxgb4 (one conflict, not so obvious to resolve,
     proper resolution is to keep the code in cxgb4_main.c as it is in
     Linus' tree as attach_uld was refactored and moved into
     cxgb4_uld.c)

   - improvements to uAPI (moved vendor specific API elements to uAPI
     area)

   - add hns-roce driver and hns and hns-roce ACPI reset support

   - conversion of all rdma code away from deprecated
     create_singlethread_workqueue

   - security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
     staging)"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (75 commits)
  staging/lustre: Disable InfiniBand support
  iw_cxgb4: add fast-path for small REG_MR operations
  cxgb4: advertise support for FR_NSMR_TPTE_WR
  IB/core: correctly handle rdma_rw_init_mrs() failure
  IB/srp: Fix infinite loop when FMR sg[0].offset != 0
  IB/srp: Remove an unused argument
  IB/core: Improve ib_map_mr_sg() documentation
  IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets
  IB/mthca: Move user vendor structures
  IB/nes: Move user vendor structures
  IB/ocrdma: Move user vendor structures
  IB/mlx4: Move user vendor structures
  IB/cxgb4: Move user vendor structures
  IB/cxgb3: Move user vendor structures
  IB/mlx5: Move and decouple user vendor structures
  IB/{core,hw}: Add constant for node_desc
  ipoib: Make ipoib_warn ratelimited
  IB/mlx4/alias_GUID: Remove deprecated create_singlethread_workqueue
  IB/ipoib_verbs: Remove deprecated create_singlethread_workqueue
  IB/ipoib: Remove deprecated create_singlethread_workqueue
  ...

Pull more rdma updates from Doug Ledford:
 "Minor updates for rxe driver"

[ Starting to do merge window pulls again - the current -git tree does
  appear to have some netfilter use-after-free issues, but I've sent
  off the report to the proper channels, and I don't want to delay merge
  window activity any more ]

* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/rxe: improved debug prints & code cleanup
  rdma_rxe: Ensure rdma_rxe init occurs at correct time
  IB/rxe: Properly honor max IRD value for rd/atomic.
  IB/{rxe,core,rdmavt}: Fix kernel crash for reg MR
  IB/rxe: Fix sending out loopback packet on netdev interface.
  IB/rxe: Avoid scheduling tasklet for userspace QP

Merge updates from Andrew Morton:

 - fsnotify updates

 - ocfs2 updates

 - all of MM

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (127 commits)
  console: don't prefer first registered if DT specifies stdout-path
  cred: simpler, 1D supplementary groups
  CREDITS: update Pavel's information, add GPG key, remove snail mail address
  mailmap: add Johan Hovold
  .gitattributes: set git diff driver for C source code files
  uprobes: remove function declarations from arch/{mips,s390}
  spelling.txt: "modeled" is spelt correctly
  nmi_backtrace: generate one-line reports for idle cpus
  arch/tile: adopt the new nmi_backtrace framework
  nmi_backtrace: do a local dump_stack() instead of a self-NMI
  nmi_backtrace: add more trigger_*_cpu_backtrace() methods
  min/max: remove sparse warnings when they're nested
  Documentation/filesystems/proc.txt: add more description for maps/smaps
  mm, proc: fix region lost in /proc/self/smaps
  proc: fix timerslack_ns CAP_SYS_NICE check when adjusting self
  proc: add LSM hook checks to /proc/<tid>/timerslack_ns
  proc: relax /proc/<tid>/timerslack_ns capability requirements
  meminfo: break apart a very long seq_printf with #ifdefs
  seq/proc: modify seq_put_decimal_[u]ll to take a const char *, not char
  proc: faster /proc/*/status
  ...

Pull ARM SoC late DT updates from Arnd Bergmann:
 "These updates have been kept in a separate branch mostly because they
  rely on updates to the respective clk drivers to keep the shared
  header files in sync.

   - The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
     automotive SoC similar to the ⅹ8a7795 chip we already support, but
     the dts changes rely on a clock driver change that has been merged
     for v4.9 through the clk tree.

   - The Amlogic meson-gxbb (S905) platform gains support for a few
     drivers merged through our tree, in particular the network and usb
     driver changes are required and included here, and also the clk
     tree changes.

   - The Allwinner platforms have seen a large-scale change to their clk
     drivers and the dts file updates must come after that. This
     includes the newly added Nextthing GR8 platform, which is derived
     from sun5i/A13.

   - Some integrator (arm32) changes rely on clk driver changes.

   - A single patch for lpc32xx has no such dependency but wasn't added
     until just before the merge window"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  ARM: dts: lpc32xx: add device node for IRAM on-chip memory
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ...

Pull ARM 64-bit DT updates from Arnd Bergmann:
 "The 64-bit DT changes are surprisingly small this time, we only add
  two SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
  UniPhier LD11 TV SoC, each with their reference boards.

  There are three new machines added for existing SoC platforms:

   - The Marvell Armada 8040 development board is an impressive
     quad-core Cortex-A72 machine with three 10gbit ethernet interfaces

   - Qualcomms DragonBoard 820c single-board computer is their current
     high-end phone platform in the 96boards form factor

   - Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
     Android box based on the 8-core rk3368 SoC"

* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (91 commits)
  arm64: dts: berlin4ct: Add L2 cache topology
  arm64: dts: berlin4ct: enable all wdt nodes unconditionally
  arm64: dts: berlin4ct: switch to Cortex-A53 specific pmu nodes
  arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
  arm64: dts: apm: Add DT node for APM X-Gene 2 CPU clocks
  arm64: dts: apm: Add X-Gene SoC hwmon to device tree
  arm64: dts: apm: Fix interrupt polarity for X-Gene PCIe legacy interrupts
  arm64: dts: apm: Add APM X-Gene v2 SoC PMU DTS entries
  arm64: dts: apm: Add APM X-Gene SoC PMU DTS entries
  arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
  arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
  arm64: dts: rockchip: add Type-C phy for RK3399
  arm64: dts: rockchip: enable the gmac for rk3399 evb board
  arm64: dts: rockchip: add the gmac needed node for rk3399
  arm64: dts: rockchip: support the pmu node for rk3399
  arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
  arm64: dts: rockchip: add the tcpc for rk3399 power domain
  arm64: dts: rockchip: add efuse0 device node for rk3399
  arm64: dts: rockchip: configure PCIe support for rk3399-evb
  arm64: dts: rockchip: add the PCIe controller support for RK3399
  ...

Pull ARM DT updates from Arnd Bergmann:
 "These are as usual a very large number of mostly boring updates to
  enable devices in existing machines, or to fix minor bugs. Notably, an
  ongoing treewide effort to fix warnings caused by an update to the
  device tree compiler. These are enabled with "make W=1" at the moment
  but can hopefully become the default once all issues have been
  addressed.

  No new SoC platform is added this time around (Armada 395 and Orion
  mv88f5181 are slight variations of existing ones), but a significant
  number of new dts files are added, which I list by platform:

   - Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
     Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
     Olimex A33-Olinuxino, and Nano Pi Neo single-board computers

   - ARM Realview: all supported machines (ported from board files)

   - Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
     BCM958622hr reference boards for Northstar platform, Raspberry Pi
     Zero single-board computer

   - Marvell EBU: Netgear WNR854T router (ported from board file),
     Armada 395 SoC platform and GP board Armada 390 DB development
     board

   - NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
     single-board computer, Technologic Systems TS-4900 and Engicam
     IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board

   - Qualcomm: LG Nexus 5 Phone

   - Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards

   - Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
     Reload platform

   - ST Microelectronics STi: B2260 (96boards) single-board computer

   - TI Davinci: OMAP-L138 LCDK Development kit

   - TI OMAP: beagleboard-x15 rev B1 single-board computer"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
  ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
  ARM: dts: chromecast: add missing unit name to /memory node
  ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
  ARM: dts: berlin2: Add missing unit name to /soc node
  ARM: dts: berlin2cd: Add missing unit name to /soc node
  ARM: dts: berlin2q: Add missing unit name to /soc node
  ARM: dts: berlin2: Remove skeleton.dtsi inclusion
  ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
  ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
  arm: dts: berlin2q: enable all wdt nodes unconditionally
  arm: dts: berlin2: enable all wdt nodes unconditionally
  ARM: dts: omap5-igep0050.dts: Use tabs for indentation
  ARM: dts: Fix igepv5 power button GPIO direction
  ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
  ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
  ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
  ARM: dts: s3c64xx: Use macros for pinctrl configuration
  ARM: dts: s3c2416: Use macros for pinctrl configuration
  ARM: dts: s5pv210: Use macros for pinctrl configuration
  ARM: dts: s3c64xx: Use common macros for pinctrl configuration
  ...

Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, including a couple of newly added
  drivers:

   - The Qualcomm external bus interface 2 (EBI2), used in some of their
     mobile phone chips for connecting flash memory, LCD displays or
     other peripherals

   - Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
     the EFUSE based on that firmware interface.

   - Perf support for the AppliedMicro X-Gene performance monitor unit

   - Reset driver for STMicroelectronics STM32

   - Reset driver for SocioNext UniPhier SoCs

  Aside from these, there are minor updates to SoC-specific bus,
  clocksource, firmware, pinctrl, reset, rtc and pmic drivers"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  bus: qcom-ebi2: depend on HAS_IOMEM
  pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
  clk: mvebu: Add clk support for the orion5x SoC mv88f5181
  dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
  clocksource: exynos_mct: Add the support for ARM64
  perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
  Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
  MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
  bus: qcom: add EBI2 driver
  bus: qcom: add EBI2 device tree bindings
  rtc: rtc-pm8xxx: Add support for pm8018 rtc
  nvmem: amlogic: Add Amlogic Meson EFUSE driver
  firmware: Amlogic: Add secure monitor driver
  soc: qcom: smd: Reset rx tail rather than tx
  memory: atmel-sdramc: fix a possible NULL dereference
  reset: hi6220: allow to compile test driver on other architectures
  reset: zynq: add driver Kconfig option
  reset: sunxi: add driver Kconfig option
  reset: stm32: add driver Kconfig option
  reset: socfpga: add driver Kconfig option
  ...

Pull ARM SoC 64-bit updates from Arnd Bergmann:
 "Changes to platform code for 64-bit ARM platforms.

  Nearly all of these are defconfig updates to enable new drivers or old
  drivers still used on these 64-bit platforms.

  Aside from that, we gain initial support for two set-top-box
  platforms, both of which already have 32-bit support in arch/arm:

   - Broadcom adds abstract support for the bcm7xxx/brcmstb platform,
     presumably the respective dts files and more information will
     follow at a later point.

   - The ZTE ZX296718 SoC for set-top-boxes, a relative of the 32-bit
     ZX296702 SoC that we already support"

* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: add ZTE ZX SoC family
  arm64: defconfig: enable ZTE ZX related config
  arm64: defconfig: enable common modules for power management
  arm64: defconfig: enable meson I2C
  arm64: defconfig: enable meson SPI as module
  arm64: defconfig: enable meson WDT as modules
  arm64: defconfig: enable HW random as module
  arm64: defconfig: Enable SDHI and GPIO_REGULATOR
  arm64: configs: enable PCIe driver for Aardvark
  Kconfig: ARCH_HISI: Add PINCTRL to HISI platform
  arm64: defconfig: enable bluetooth supports as modules
  arm64: defconfig: enable CONFIG_INPUT_HISI_POWERKEY for HiKey
  arm64: defconfig: Enable HiSilicon kirin drm, adv7533 for HiKey
  arm64: defconfig: Enable Hisi SAS and HNS
  arm64: defconfig: Enable QDF2432 config options
  arm64: sunxi: Kconfig: add essential pinctrl driver
  arm64: defconfig: Add Renesas R-Car HSUSB driver support as module
  arm64: Add Broadcom Set Top Box Kconfig entry point
  arm64: defconfig: enable xhci-platform

Pull ARM SoC defconfig updates from Arnd Bergmann:
 "Defconfig additions, removals, etc. Most of these are small changes
  adding the options for newly upstreamed drivers, or drivers needed for
  new board support. Nothing specifically sticks out this time"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
  ARM: multi_v7_defconfig: enable CONFIG_EFI
  ARM: multi_v7_defconfig: Build Atmel maXTouch driver as a module
  ARM: defconfig: update the Integrator defconfig
  ARM: keystone: defconfig: Fix USB configuration
  ARM: imx_v6_v7_defconfig: Select the wm8960 codec driver
  ARM: omap2plus_defconfig: switch to the IIO BMP085 driver
  ARM: mvebu_v5_defconfig: use MV88E6XXX
  ARM: davinci_all_defconfig: Enable some UBI modules
  ARM: davinci_all_defconfig: Enable AEMIF as a module
  ARM: multi_v7_defconfig: Enable SECCOMP
  ARM: exynos_defconfig: Enable SECCOMP
  ARM: imx_v6_v7_defconfig: Add CONFIG_MPL3115
  ARM: imx_v6_v7_defconfig: Enable GPU support
  ARM: s3c2410_defconfig: Remove CONFIG_IPV6_PRIVACY
  ARM: exynos_defconfig: Enable PM_DEBUG
  ARM: exynos_defconfig: Enable bus frequency scaling with devfreq
  ARM: imx_v6_v7_defconfig: enable more USB configurations
  ARM: davinci_all_defconfig: enable SMSC ethernet PHY
  ARM: davinci_all_defconfig: enable RTC driver as module
  ARM: multi_v7_defconfig: Enable ARM_IMX6Q_CPUFREQ
  ...

Pull ARM SoC platform updates from Arnd Bergmann:
 "These are updates for platform specific code on 32-bit ARM machines,
  essentially anything that can not (yet) be expressed using DT files.

  Noteworthy changes include:

   - We get support for running in big-endian mode on two platforms:
     sunxi (Allwinner) and s3c24xx (old Samsung).

   - The recently added Uniphier platform now uses standard PSCI methods
     for SMP booting and we remove support for old bootloader versions
     that did not support it yet.

   - In sunxi, we gain support for the "Nextthing GR8" SoC, which is a
     close relative of the Allwinner A13 and R8 chips.

   - PXA completes its move over to the generic dmaengine framework and
     removes its old private API

   - mach-bcm gains support for BCM47189/BCM53573, their first ARM SoC
     with integrated 802.11ac wireless networking"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  ARM: imx legacy: pca100: move peripheral initialization to .init_late
  ARM: imx legacy: mx27ads: move peripheral initialization to .init_late
  ARM: imx legacy: mx21ads: move peripheral initialization to .init_late
  ARM: imx legacy: pcm043: move peripheral initialization to .init_late
  ARM: imx legacy: mx35-3ds: move peripheral initialization to .init_late
  ARM: imx legacy: mx27-3ds: move peripheral initialization to .init_late
  ARM: imx legacy: imx27-visstrim-m10: move peripheral initialization to .init_late
  ARM: imx legacy: vpr200: move peripheral initialization to .init_late
  ARM: imx legacy: mx31moboard: move peripheral initialization to .init_late
  ARM: imx legacy: armadillo5x0: move peripheral initialization to .init_late
  ARM: imx legacy: qong: move peripheral initialization to .init_late
  ARM: imx legacy: mx31-3ds: move peripheral initialization to .init_late
  ARM: imx legacy: pcm037: move peripheral initialization to .init_late
  ARM: imx legacy: mx31lilly: move peripheral initialization to .init_late
  ARM: imx legacy: mx31ads: move peripheral initialization to .init_late
  ARM: imx legacy: mx31lite: move peripheral initialization to .init_late
  ARM: imx legacy: kzm: move peripheral initialization to .init_late
  MAINTAINERS: update list of Oxnas maintainers
  ARM: orion5x: remove extraneous NO_IRQ
  ARM: orion: simplify orion_ge00_switch_init
  ...

Pull ARM SoC cleanups from Arnd Bergmann:
 "The cleanups for v4.9 are a little larger that usual, but thankfully
  that is almost exclusively due to removing a significant number of
  files that have become obsolete after the still ongoing conversion of
  old board files to devicetree.

   - for mach-omap2, which is still the largest platform in arch/arm/,
     the conversion to DT is finally complete after the Nokia N900 is
     now fully supported there, along with the omap3 LDP, and we can
     remove those two board files. If no regressions are found, another
     large cleanup for the platform will happen as a follow-up, removing
     dead code and restructuring the platform based on being DT-only.

   - In mach-imx, similar work is ongoing, but has not come that far.
     This time, we remove the obsolete board file for the i.MX1
     generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
     DT-only. The remaining board files are for i.MX2 and i.MX3 machines
     based on old ARM926 or ARM1136 cores that should work with DT in
     principle.

   - realview has just been converted from board files to DT, and a lot
     of code gets removed in the process. This is the last
     ARM/Keil/Versatile derived platform that was still using board
     files, the other ones being integrator, versatile and vexpress. We
     can probably merge the remaining code into a single directory in
     the near future.

   - clps711x had completed the conversion in v4.8, but we accidentally
     left the files in place that should have been deleted then"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
  ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
  ARM: imx: (trivial) fix typo and grammar
  ARM: clps711x: remove extraneous files
  ARM: imx: use IS_ENABLED() instead of checking for built-in or module
  ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
  ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
  ARM: imx: remove platform-mxc_rnga
  ARM: realview: imply device tree boot
  ARM: realview: no need to select SMP_ON_UP explicitly
  ARM: realview: delete the RealView board files
  ARM: imx: no need to select SMP_ON_UP explicitly
  ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
  ARM: i.MX: Remove i.MX1 non-DT support
  ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
  ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
  ARM: mxs: remove obsolete startup code for TX28
  ARM: i.MX31 iomux: remove duplicates with alternate name
  ARM: i.MX31 iomux: remove plain duplicates
  ARM: OMAP2+: Drop legacy board file for LDP
  ...

Pull parisc updates from Helge Deller:
 "Changes include:

   - Fix boot of 32bit SMP kernel (initial kernel mapping was too small)

   - Added hardened usercopy checks

   - Drop bootmem and switch to memblock and NO_BOOTMEM implementation

   - Drop the BROKEN_RODATA config option (and thus remove the relevant
     code from the generic headers and files because parisc was the last
     architecture which used this config option)

   - Improve segfault reporting by printing human readable error strings

   - Various smaller changes, e.g. dwarf debug support for assembly
     code, update comments regarding copy_user_page_asm, switch to
     kmalloc_array()"

* 'parisc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Increase KERNEL_INITIAL_SIZE for 32-bit SMP kernels
  parisc: Drop bootmem and switch to memblock
  parisc: Add hardened usercopy feature
  parisc: Add cfi_startproc and cfi_endproc to assembly code
  parisc: Move hpmc stack into page aligned bss section
  parisc: Fix self-detected CPU stall warnings on Mako machines
  parisc: Report trap type as human readable string
  parisc: Update comment regarding implementation of copy_user_page_asm
  parisc: Use kmalloc_array() in add_system_map_addresses()
  parisc: Check return value of smp_boot_one_cpu()
  parisc: Drop BROKEN_RODATA config option

Pull avr32 update from Hans-Christian Noren Egtvedt.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
  avr32: migrate exception table users off module.h and onto extable.h

Pull powerpc updates from Michael Ellerman:
 "Highlights:
   - Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
   - Use gas sections for arranging exception vectors et. al.
   - Large set of TM cleanups and selftests (Cyril Bur)
   - Enable transactional memory (TM) lazily for userspace (Cyril Bur)
   - Support for XZ compression in the zImage wrapper (Oliver
     O'Halloran)
   - Add support for bpf constant blinding (Naveen N. Rao)
   - Beginnings of upstream support for PA Semi Nemo motherboards
     (Darren Stevens)

  Fixes:
   - Ensure .mem(init|exit).text are within _stext/_etext (Michael
     Ellerman)
   - xmon: Don't use ld on 32-bit (Michael Ellerman)
   - vdso64: Use double word compare on pointers (Anton Blanchard)
   - powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
   - powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
   - powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K
     (Aneesh Kumar K.V)
   - Fix memory leak in queue_hotplug_event() error path (Andrew
     Donnellan)
   - Replay hypervisor maintenance interrupt first (Nicholas Piggin)

  Various performance optimisations (Anton Blanchard):
   - Align hot loops of memset() and backwards_memcpy()
   - During context switch, check before setting mm_cpumask
   - Remove static branch prediction in atomic{, 64}_add_unless
   - Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little
     endian
   - Set default CPU type to POWER8 for little endian builds

  Cleanups & features:
   - Sparse fixes/cleanups (Daniel Axtens)
   - Preserve CFAR value on SLB miss caused by access to bogus address
     (Paul Mackerras)
   - Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
   - Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU)
     (Simon Guo)
   - Optimise syscall entry for virtual, relocatable case (Nicholas
     Piggin)
   - Optimise MSR handling in exception handling (Nicholas Piggin)
   - Support for kexec with Radix MMU (Benjamin Herrenschmidt)
   - powernv EEH fixes (Russell Currey)
   - Suprise PCI hotplug support for powernv (Gavin Shan)
   - Endian/sparse fixes for powernv PCI (Gavin Shan)
   - Defconfig updates (Anton Blanchard)
   - KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
   - cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
   - cxl: replace loop with for_each_child_of_node(), remove unneeded
     of_node_put() (Andrew Donnellan)
   - Fix HV facility unavailable to use correct handler (Nicholas
     Piggin)
   - Remove unnecessary syscall trampoline (Nicholas Piggin)
   - fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael
     Ellerman)
   - Quieten EEH message when no adapters are found (Anton Blanchard)
   - powernv: Add PHB register dump debugfs handle (Russell Currey)
   - Use kprobe blacklist for exception handlers & asm functions
     (Nicholas Piggin)
   - Document the syscall ABI (Nicholas Piggin)
   - MAINTAINERS: Update cxl maintainers (Michael Neuling)
   - powerpc: Remove all usages of NO_IRQ (Michael Ellerman)

  Minor cleanups:
   - Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur,
     Frederic Barrat, Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng,
     Simon Guo"

* tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (156 commits)
  powerpc/bpf: Add support for bpf constant blinding
  powerpc/bpf: Implement support for tail calls
  powerpc/bpf: Introduce accessors for using the tmp local stack space
  powerpc/fadump: Fix build break when CONFIG_PROC_VMCORE=n
  powerpc: tm: Enable transactional memory (TM) lazily for userspace
  powerpc/tm: Add TM Unavailable Exception
  powerpc: Remove do_load_up_transact_{fpu,altivec}
  powerpc: tm: Rename transct_(*) to ck(\1)_state
  powerpc: tm: Always use fp_state and vr_state to store live registers
  selftests/powerpc: Add checks for transactional VSXs in signal contexts
  selftests/powerpc: Add checks for transactional VMXs in signal contexts
  selftests/powerpc: Add checks for transactional FPUs in signal contexts
  selftests/powerpc: Add checks for transactional GPRs in signal contexts
  selftests/powerpc: Check that signals always get delivered
  selftests/powerpc: Add TM tcheck helpers in C
  selftests/powerpc: Allow tests to extend their kill timeout
  selftests/powerpc: Introduce GPR asm helper header file
  selftests/powerpc: Move VMX stack frame macros to header file
  selftests/powerpc: Rework FPU stack placement macros and move to header file
  selftests/powerpc: Check for VSX preservation across userspace preemption
  ...

If a device tree specifies a preferred device for kernel console output
via the stdout-path or linux,stdout-path chosen node properties or the
stdout alias then the kernel ought to honor it & output the kernel
console to that device.  As it stands, this isn't the case.  Whilst we
parse the stdout-path properties & set an of_stdout variable from
of_alias_scan(), and use that from of_console_check() to determine
whether to add a console device as a preferred console whilst
registering it, we also prefer the first registered console if no other
has been selected at the time of its registration.

This means that if a console other than the one the device tree selects
via stdout-path is registered first, we will switch to using it & when
the stdout-path console is later registered the call to
add_preferred_console() via of_console_check() is too late to do
anything useful.  In practice this seems to mean that we switch to the
dummy console device fairly early & see no further console output:

    Console: colour dummy device 80x25
    console [tty0] enabled
    bootconsole [ns16550a0] disabled

Fix this by not automatically preferring the first registered console if
one is specified by the device tree.  This allows consoles to be
registered but not enabled, and once the driver for the console selected
by stdout-path calls of_console_check() the driver will be added to the
list of preferred consoles before any other console has been enabled.
When that console is then registered via register_console() it will be
enabled as expected.

Link: http://lkml.kernel.org/r/20160809151937.26118-1-paul.burton@imgtec.comSigned-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ivan Delalande <colona@arista.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Jan Kara <jack@suse.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Current supplementary groups code can massively overallocate memory and
is implemented in a way so that access to individual gid is done via 2D
array.

If number of gids is <= 32, memory allocation is more or less tolerable
(140/148 bytes).  But if it is not, code allocates full page (!)
regardless and, what's even more fun, doesn't reuse small 32-entry
array.

2D array means dependent shifts, loads and LEAs without possibility to
optimize them (gid is never known at compile time).

All of the above is unnecessary.  Switch to the usual
trailing-zero-len-array scheme.  Memory is allocated with
kmalloc/vmalloc() and only as much as needed.  Accesses become simpler
(LEA 8(gi,idx,4) or even without displacement).

Maximum number of gids is 65536 which translates to 256KB+8 bytes.  I
think kernel can handle such allocation.

On my usual desktop system with whole 9 (nine) aux groups, struct
group_info shrinks from 148 bytes to 44 bytes, yay!

Nice side effects:

 - "gi->gid[i]" is shorter than "GROUP_AT(gi, i)", less typing,

 - fix little mess in net/ipv4/ping.c
   should have been using GROUP_AT macro but this point becomes moot,

 - aux group allocation is persistent and should be accounted as such.

Link: http://lkml.kernel.org/r/20160817201927.GA2096@p183.telecom.bySigned-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Vasily Kulikov <segoon@openwall.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Link: http://lkml.kernel.org/r/20161003082312.GA20634@amdSigned-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add two entries to map to my primary address.

Link: http://lkml.kernel.org/r/1473850348-19177-1-git-send-email-johan@kernel.orgSigned-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Git can be told to apply language-specific rules when generating diffs.
Enable this for C source code files (*.c and *.h) so that function names
are printed right.  Specifically, doing so prevents "git diff" from
mistakenly considering unindented goto labels as function names.

Link: http://lkml.kernel.org/r/20160907143403.1449324f@endymionSigned-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Joe Perches <joe@perches.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The declarations of arch-specific functions have been moved to a common
header in commit 3820b4d2 ('uprobes: Move function declarations out
of arch'), but MIPS and S390 has added them to their own trees later.
Remove the unnecessary duplicates.

Link: http://lkml.kernel.org/r/1472804384-17830-1-git-send-email-marcin.nowakowski@imgtec.comSigned-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

No need to correct the correct.

Link: http://lkml.kernel.org/r/1472490791.3425.38.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative.  Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".

We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.

This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.

Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.comSigned-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Previously tile was rolling its own method of capturing backtrace data
in the NMI handlers, but it was relying on running printk() from the NMI
handler, which is not always safe.  So adopt the nmi_backtrace model
(with the new cpumask extension) instead.

So we can call the nmi_backtrace code directly from the nmi handler,
move the nmi_enter()/exit() into the top-level tile NMI handler.

The semantics of the routine change slightly since it is now synchronous
with the remote cores completing the backtraces.  Previously it was
asynchronous, but with protection to avoid starting a new remote
backtrace if the old one was still in progress.

Link: http://lkml.kernel.org/r/1472487169-14923-4-git-send-email-cmetcalf@mellanox.comSigned-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Cc: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently on arm there is code that checks whether it should call
dump_stack() explicitly, to avoid trying to raise an NMI when the
current context is not preemptible by the backtrace IPI.  Similarly, the
forthcoming arch/tile support uses an IPI mechanism that does not
support generating an NMI to self.

Accordingly, move the code that guards this case into the generic
mechanism, and invoke it unconditionally whenever we want a backtrace of
the current cpu.  It seems plausible that in all cases, dump_stack()
will generate better information than generating a stack from the NMI
handler.  The register state will be missing, but that state is likely
not particularly helpful in any case.

Or, if we think it is helpful, we should be capturing and emitting the
current register state in all cases when regs == NULL is passed to
nmi_cpu_backtrace().

Link: http://lkml.kernel.org/r/1472487169-14923-3-git-send-email-cmetcalf@mellanox.comSigned-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Aaron Tomlin <atomlin@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Patch series "improvements to the nmi_backtrace code" v9.

This patch series modifies the trigger_xxx_backtrace() NMI-based remote
backtracing code to make it more flexible, and makes a few small
improvements along the way.

The motivation comes from the task isolation code, where there are
scenarios where we want to be able to diagnose a case where some cpu is
about to interrupt a task-isolated cpu.  It can be helpful to see both
where the interrupting cpu is, and also an approximation of where the
cpu that is being interrupted is.  The nmi_backtrace framework allows us
to discover the stack of the interrupted cpu.

I've tested that the change works as desired on tile, and build-tested
x86, arm, mips, and sparc64.  For x86 I confirmed that the generic
cpuidle stuff as well as the architecture-specific routines are in the
new cpuidle section.  For arm, mips, and sparc I just build-tested it
and made sure the generic cpuidle routines were in the new cpuidle
section, but I didn't attempt to figure out which the platform-specific
idle routines might be.  That might be more usefully done by someone
with platform experience in follow-up patches.

This patch (of 4):

Currently you can only request a backtrace of either all cpus, or all
cpus but yourself.  It can also be helpful to request a remote backtrace
of a single cpu, and since we want that, the logical extension is to
support a cpumask as the underlying primitive.

This change modifies the existing lib/nmi_backtrace.c code to take a
cpumask as its basic primitive, and modifies the linux/nmi.h code to use
the new "cpumask" method instead.

The existing clients of nmi_backtrace (arm and x86) are converted to
using the new cpumask approach in this change.

The other users of the backtracing API (sparc64 and mips) are converted
to use the cpumask approach rather than the all/allbutself approach.
The mips code ignored the "include_self" boolean but with this change it
will now also dump a local backtrace if requested.

Link: http://lkml.kernel.org/r/1472487169-14923-2-git-send-email-cmetcalf@mellanox.comSigned-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>