I2C host controller need to be configured properly in order to meet I2C
timings specified in the I2C protocol specification. Some Intel Broxton
based machines do not have this information in the ACPI namespace (or the
boot firmware does not support ACPI at all) so we use build-in device
properties instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds macros to define masks and bits for imx6sx
PCIe registers. This is based on a patch by Richard Zhu.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The ipaq-micro driver uses SET_SYSTEM_SLEEP_PM_OPS() to
remove the reference to its resume function, but does
not use an #ifdef around the definition, so we get
a build warning:

drivers/mfd/ipaq-micro.c:379:12: error: 'micro_resume' defined but not used [-Werror=unused-function]

This adds a __maybe_unused annotation so the compiler knows
it can silently drop it instead of warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The max77686 MFD driver supports both the Maxim 77686 and Maxim 77802
PMICs but only the OF device table contains entries for both devices.

The max77802 entry is missing in the I2C device ID table which isn't
a problem currently since the driver only supports DT but it will be
needed if the driver is changed to be built as a module since the I2C
core always reports a I2C modalias uevent so auto-load will not work.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When the device is registered via OF, the OF table is used to match the
driver instead of the I2C device ID table but the entries in the latter
are used as aliasses to load the module if the driver was not built-in.

This is because the I2C core always reports an I2C module alias instead
of an OF one but that could change so it is better to always export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The driver's Kconfig symbol is a boolean but nothing prevents the driver
to be built as a module instead of built-in. It is true that most system
integrators will choose the latter but the config should not restrict it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This adds the PWM resources to the STMPE MFD driver, so that
it can properly grab and use them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).

tps65090 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When CONFIG_MFD_SYSCON is disabled, have the function stubs return
ENOTSUPP to indicate the syscon functionality is not available.
There are currently no callers that depend on the ENOSYS return value.

This patchfixes a checkpatch warning:
    WARNING: ENOSYS means 'invalid syscall nr' and nothing else
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).

as3711 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regmap config max_register field should contain number of
device last register, however num_reg_defaults_raw field
should be set to register count instead
(usually one register more than max_register).

rc5t583 driver had both of these fields set to the same value,
fix this by introducing separate defines for max register
number and total count of registers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the TPS65086 PMIC GPOs.

TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The platform bus_type .match callback attempts to match the platform device
name with an entry on the .id_table if provided and fallbacks to match with
the driver's name if a table is not provided.

Using a platform device ID to match is more explicit, allows the driver to
support more than one device and also the MODULE_DEVICE_TABLE macro can be
used to export the module aliases information instead of the MODULE_ALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9063.

These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.

When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.

As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9063 core.

In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

MT6323 has the INT_CON and INT_STATUS located at a different position.
Make the registers locations configurable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9062.

These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.

When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.

As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9062 core.

In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Active-semi ACT8945A PMIC is a Multi-Function Device, it has
two subdevices:
 - Regulator
 - Charger

This patch adds documentation for ACT8945A DT bindings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds support for the Active-semi ACT8945A PMIC.
It is a Multi Function Device with the following subdevices:
 - Regulator
 - Charger

It is interfaced to the host controller using I2C interface,
ACT8945A is a child device of the I2C.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

s/cros_ec_register/cros_ec_query_all
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

MFD_ARIZONA_I2C and MFD_ARIZONA_SPI both select MFD_ARIZONA and all
three of those select MFD_CORE, this makes the selects of MFD_CORE in
MFD_ARIZONA_I2C and MFD_ARIZONA_SPI redundant, so we remove them.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

My automated test is back and now can check defaults against the actual
hardware. This patch updates the defaults array for the differences
detected and removes a couple of completely unused registers.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The help text had a copy and paste error and refers to I2C in the SPI
section. This patch corrects this typo.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

syscon_regmap_config can be made const if syscon_probe() creates a local
copy on the stack, just like syscon_register() does.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Determine the regmap max_register configuration from the io resource size
and the reg-io-width device tree property.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The prcmu_config_clkout() function ensures that the 'clkout' argument
can only be '0' or '1' using an appropriate BUG_ON(), so the compiler
should know that the div_mask, mask, and bits variables are always
initialized later on. However, it doesn't understand this in gcc-5.2
and produces a false positive warning instead:

drivers/mfd/db8500-prcmu.c: In function 'prcmu_config_clkout':
drivers/mfd/db8500-prcmu.c:762:10: error: 'div_mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  if (val & div_mask) {
          ^
drivers/mfd/db8500-prcmu.c:769:13: error: 'mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
    if ((val & mask & ~div_mask) != bits) {
             ^
drivers/mfd/db8500-prcmu.c:757:7: error: 'bits' may be used uninitialized in this function [-Werror=maybe-uninitialized]

Replacing the switch() statement with an equivalent if() lets
gcc figure this out reliably and avoids the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the TPS65912 device. It provides communication
through I2C and contains the following components:

 - Regulators
 - Load switches
 - GPO controller
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The TPS65086 PMIC contains several regulators and a GPO controller.
Add bindings for the TPS65086 PMIC.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add PCI IDs for Intel Broxton B-Step platform, which have same
LPSS devices with A-Step.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
cked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

These drivers can be built as module, so make them depend on I2C rather
than I2C=y.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

We forgot to remove the clock tree if something goes wrong in ->probe(). Add a
call to intel_lpss_unregister_clock() on error path in ->probe() to fix the
potential issue.

Fixes: 4b45efe8 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

tps65010 driver's initcall cannot succeed when the driver is built-in,
because it expects that the I2C probe is completed at initcall time;
this cannot happen as MFD is initialized before I2C. Also on systems
where the chip is not present there is unnecessary 30 ms delay during
the boot.

Instead of waiting for probe to finish, just register the I2C device.
If some boards need retry mechanism for startup glitches, that should be
done in the actual probe function. Also delete the driver banner message.

The patch allows to use tps65010 again with OMAP1 (where it's required
to be built-in) and enables e.g. USB and LED functionality on OMAP5912 OSK.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge branches 'ib-mfd-clk-4.6', 'ib-mfd-input-iio-4.6', 'ib-mfd-regulator-4.6' and 'ib-mfd-regulator-gpio-4.6' into ibs-for-mfd-merged

The newly added driver uses do_div() to device a 32-bit number, which now
provokes a warning:

drivers/iio/adc/fsl-imx25-gcq.c: In function 'mx25_gcq_setup_cfgs':
include/asm-generic/div64.h:207:28: warning: comparison of distinct pointer types lacks a cast
  (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \

This replaces the do_div() call with a straight division operator.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6df2e98c ("iio: adc: Add imx25-gcq ADC driver")
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>