- 30 Nov, 2017 40 commits
-
-
John David Anglin authored
commit 05f016d2 upstream. As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS implementation causes a kernel crash. The attached patch corrects the off by one error in the argument validity check. In reviewing the code, I noticed that we only perform word operations with the pointer size argument. The subi instruction intentionally uses a word condition on 64-bit kernels. Nullification was used instead of a cmpib instruction as the branch should never be taken. The shlw pseudo-operation generates a depw,z instruction and it clears the target before doing a shift left word deposit. Thus, we don't need to clip the upper 32 bits of this argument on 64-bit kernels. Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic code in libgcc is the only direct user of the new CAS implementation that I am aware of. Signed-off-by:
John David Anglin <dave.anglin@bell.net> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Brian King authored
commit 0a9a17e3 upstream. This patch fixes an issue seen on Power systems with ixgbe which results in skb list corruption and an eventual kernel oops. The following is what was observed: CPU 1 CPU2 ============================ ============================ 1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq 2: first->skb = skb eop_desc = tx_buffer->next_to_watch 3: ixgbe_tx_map read_barrier_depends() 4: wmb check adapter written status bit 5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..); 6: writel(i, tx_ring->tail); The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not get loaded prior to tx_buffer->next_to_watch, which then results in loading a stale skb pointer. This patch replaces the read_barrier_depends with smp_rmb to ensure loads are ordered with respect to the load of tx_buffer->next_to_watch. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Acked-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Brian King authored
commit 7b8edcc6 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with fm10k as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit f72271e2 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with i40evf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit ae0c585d upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with ixgbevf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit 1e1f9ca5 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igbvf as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Brian King authored
commit c4cb9918 upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with igb as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Brian King authored
commit 52c6912f upstream. The original issue being fixed in this patch was seen with the ixgbe driver, but the same issue exists with i40e as well, as the code is very similar. read_barrier_depends is not sufficient to ensure loads following it are not speculatively loaded out of order by the CPU, which can result in stale data being loaded, causing potential system crashes. Signed-off-by:
-
Johan Hovold authored
commit c45e3e4c upstream. A recent change fixing NFC device allocation itself introduced an error-handling bug by returning an error pointer in case device-id allocation failed. This is clearly broken as the callers still expected NULL to be returned on errors as detected by Dan's static checker. Fix this up by returning NULL in the event that we've run out of memory when allocating a new device id. Note that the offending commit is marked for stable (3.8) so this fix needs to be backported along with it. Fixes: 20777bc5 ("NFC: fix broken device allocation") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Bart Van Assche authored
commit 8a0d18c6 upstream. This patch fixes the following kernel crash: general protection fault: 0000 [#1] PREEMPT SMP Workqueue: ib_mad2 timeout_sends [ib_core] Call Trace: ib_sa_path_rec_callback+0x1c4/0x1d0 [ib_core] send_handler+0xb2/0xd0 [ib_core] timeout_sends+0x14d/0x220 [ib_core] process_one_work+0x200/0x630 worker_thread+0x4e/0x3b0 kthread+0x113/0x150 Fixes: commit aef9ec39 ("IB: Add SCSI RDMA Protocol (SRP) initiator") Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit c70ca389 upstream. Make srpt_parse_i_port_id() return a negative value if hex2bin() fails. Fixes: commit a42d985b ("ib_srpt: Initial SRP Target merge for v3.3-rc1") Signed-off-by:
-
Dan Williams authored
commit c1fb3542 upstream. For the same reason that /proc/iomem returns 0's for non-root readers and acpi tables are root-only, make the 'resource' attribute for namespace devices only readable by root. Otherwise we disclose physical address information. Fixes: bf9bccc1 ("libnvdimm: pmem label sets and namespace instantiation") Reported-by:
Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Dan Williams authored
commit b18d4b8a upstream. The set of valid sequence numbers is {1,2,3}. The specification indicates that an implementation should consider 0 a sign of a critical error: UEFI 2.7: 13.19 NVDIMM Label Protocol Software never writes the sequence number 00, so a correctly check-summed Index Block with this sequence number probably indicates a critical error. When software discovers this case it treats it as an invalid Index Block indication. While the expectation is that the invalid block is just thrown away, the Robustness Principle says we should fix this to make both sequence numbers valid. Fixes: f524bf27 ("libnvdimm: write pmem label set") Reported-by:
Juston Li <juston.li@intel.com> Signed-off-by:
-
Dan Williams authored
commit 26417ae4 upstream. For the same reason that /proc/iomem returns 0's for non-root readers and acpi tables are root-only, make the 'resource' attribute for pfn devices only readable by root. Otherwise we disclose physical address information. Fixes: f6ed58c7 ("libnvdimm, pfn: 'resource'-address and 'size'...") Reported-by:
-
Johan Hovold authored
commit 33ec6dbc upstream. Fix child node-lookup during probe, which ended up searching the whole device tree depth-first starting at parent rather than just matching on its children. Note that the original premature free of the parent node has already been fixed separately, but that fix was apparently never backported to stable. Fixes: 9ac33b0c ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)") Fixes: 660e1551 ("clk: ti: dra7-atl-clock: Fix of_node reference counting") Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Trond Myklebust authored
commit e9d4bf21 upstream. There is no guarantee that either the request or the svc_xprt exist by the time we get round to printing the trace message. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
commit 15038e14 upstream. For many years some users of assigned devices have reported worse performance on AMD processors with NPT than on AMD without NPT, Intel or bare metal. The reason turned out to be that SVM is discarding the guest PAT setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-, PA3=UC). The guest might be using a different setting, and especially might want write combining but isn't getting it (instead getting slow UC or UC- accesses). Thanks a lot to geoff@hostfission.com for noticing the relation to the g_pat setting. The patch has been tested also by a bunch of people on VFIO users forums. Fixes: 709ddebf Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Reviewed-by:
David Hildenbrand <david@redhat.com> Tested-by:
Nick Sarnie <commendsarnex@gmail.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Ladi Prosek authored
commit 21f2d551 upstream. Intel SDM 27.5.2 Loading Host Segment and Descriptor-Table Registers: "The GDTR and IDTR limits are each set to FFFFH." Signed-off-by:
Ladi Prosek <lprosek@redhat.com> Signed-off-by:
-
Vasily Averin authored
commit dc3033e1 upstream. lockd_up() can call lockd_unregister_notifiers twice: inside lockd_start_svc() when it calls lockd_svc_exit_thread() and then in error path of lockd_up() Patch forces lockd_start_svc() to unregister notifiers in all error cases and removes extra unregister in error path of lockd_up(). Fixes: cb7d224f "lockd: unregister notifier blocks if the service ..." Signed-off-by:
Vasily Averin <vvs@virtuozzo.com> Reviewed-by:
Jeff Layton <jlayton@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 00ee9a1c upstream. Fix child-node lookup during initialisation, which ended up searching the whole device tree depth-first starting at the parent rather than just matching on its children. To make things worse, the parent gic node was prematurely freed, while the ppi-partitions node was leaked. Fixes: e3825ba1 ("irqchip/gic-v3: Add support for partitioned PPIs") Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Bart Van Assche authored
commit 4e9b6f20 upstream. Make sure that if the timeout timer fires after a queue has been marked "dying" that the affected requests are finished. Reported-by:
chenxiang (M) <chenxiang66@hisilicon.com> Fixes: commit 287922eb ("block: defer timeouts to a workqueue") Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Andrey Konovalov authored
commit fc09785d upstream. ieee80211_register_hw() in p54_register_common() may fail and leds won't get initialized. Currently p54_unregister_common() doesn't check that and always calls p54_unregister_leds(). The fix is to check priv->registered flag before calling p54_unregister_leds(). Found by syzkaller. INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 1 PID: 1404 Comm: kworker/1:1 Not tainted 4.14.0-rc1-42251-gebb2c243-dirty #205 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x292/0x395 lib/dump_stack.c:52 register_lock_class+0x6c4/0x1a00 kernel/locking/lockdep.c:769 __lock_acquire+0x27e/0x4550 kernel/locking/lockdep.c:3385 lock_acquire+0x259/0x620 kernel/locking/lockdep.c:4002 flush_work+0xf0/0x8c0 kernel/workqueue.c:2886 __cancel_work_timer+0x51d/0x870 kernel/workqueue.c:2961 cancel_delayed_work_sync+0x1f/0x30 kernel/workqueue.c:3081 p54_unregister_leds+0x6c/0xc0 drivers/net/wireless/intersil/p54/led.c:160 p54_unregister_common+0x3d/0xb0 drivers/net/wireless/intersil/p54/main.c:856 p54u_disconnect+0x86/0x120 drivers/net/wireless/intersil/p54/p54usb.c:1073 usb_unbind_interface+0x21c/0xa90 drivers/usb/core/driver.c:423 __device_release_driver drivers/base/dd.c:861 device_release_driver_internal+0x4f4/0x5c0 drivers/base/dd.c:893 device_release_driver+0x1e/0x30 drivers/base/dd.c:918 bus_remove_device+0x2f4/0x4b0 drivers/base/bus.c:565 device_del+0x5c4/0xab0 drivers/base/core.c:1985 usb_disable_device+0x1e9/0x680 drivers/usb/core/message.c:1170 usb_disconnect+0x260/0x7a0 drivers/usb/core/hub.c:2124 hub_port_connect drivers/usb/core/hub.c:4754 hub_port_connect_change drivers/usb/core/hub.c:5009 port_event drivers/usb/core/hub.c:5115 hub_event+0x1318/0x3740 drivers/usb/core/hub.c:5195 process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119 process_scheduled_works kernel/workqueue.c:2179 worker_thread+0xb2b/0x1850 kernel/workqueue.c:2255 kthread+0x3a1/0x470 kernel/kthread.c:231 ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431 Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Acked-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Xiaolei Li authored
commit 1d2fcdcf upstream. For MT2701 NAND Controller, there may generate infinite ECC decode IRQ during long time burn test on some platforms. Once this issue occurred, the ECC decode IRQ status cannot be cleared in the IRQ handler function, and threads cannot be scheduled. ECC HW generates decode IRQ each sector, so there will have more than one decode IRQ if read one page of large page NAND. Currently, ECC IRQ handle flow is that we will check whether it is decode IRQ at first by reading the register ECC_DECIRQ_STA. This is a read-clear type register. If this IRQ is decode IRQ, then the ECC IRQ signal will be cleared at the same time. Secondly, we will check whether all sectors are decoded by reading the register ECC_DECDONE. This is because the current IRQ may be not dealed in time, and the next sectors have been decoded before reading the register ECC_DECIRQ_STA. Then, the next sectors's decode IRQs will not be generated. Thirdly, if all sectors are decoded by comparing with ecc->sectors, then we will complete ecc->done, set ecc->sectors as 0, and disable ECC IRQ by programming the register ECC_IRQ_REG(op) as 0. Otherwise, wait for the next ECC IRQ. But, there is a timing issue between step one and two. When we read the reigster ECC_DECIRQ_STA, all sectors are decoded except the last sector, and the ECC IRQ signal is cleared. But the last sector is decoded before reading ECC_DECDONE, so the ECC IRQ signal is enabled again by ECC HW, and it means we will receive one extra ECC IRQ later. In step three, we will find that all sectors were decoded, then disable ECC IRQ and return. When deal with the extra ECC IRQ, the ECC IRQ status cannot be cleared anymore. That is because the register ECC_DECIRQ_STA can only be cleared when the register ECC_IRQ_REG(op) is enabled. But actually we have disabled ECC IRQ in the previous ECC IRQ handle. So, there will keep receiving ECC decode IRQ. Now, we read the register ECC_DECIRQ_STA once again before completing the ecc done event. This ensures that there will be no extra ECC decode IRQ. Also, remove writel(0, ecc->regs + ECC_IRQ_REG(op)) from irq handler, because ECC IRQ is disabled in mtk_ecc_disable(). And clear ECC_DECIRQ_STA in mtk_ecc_disable() in case there is a timeout to wait decode IRQ. Fixes: 1d6b1e46 ("mtd: mediatek: driver for MTK Smart Device") Signed-off-by:
Xiaolei Li <xiaolei.li@mediatek.com> Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Brent Taylor authored
commit 30863e38 upstream. When mtdoops calls mtd_panic_write(), it eventually calls panic_nand_write() in nand_base.c. In order to properly wait for the nand chip to be ready in panic_nand_wait(), the chip must first be selected. When using the atmel nand flash controller, a panic would occur due to a NULL pointer exception. Fixes: 2af7c653 ("mtd: Add panic_write for NAND flashes") Signed-off-by:
Brent Taylor <motobud@gmail.com> Signed-off-by:
-
Roger Quadros authored
commit 739c6441 upstream. Since v4.12, NAND subpage writes were causing a NULL pointer dereference on OMAP platforms (omap2-nand) using OMAP_ECC_BCH4_CODE_HW, OMAP_ECC_BCH8_CODE_HW and OMAP_ECC_BCH16_CODE_HW. This is because for those ECC modes, omap_calculate_ecc_bch() generates ECC bytes for the entire (multi-sector) page and this can overflow the ECC buffer provided by nand_write_subpage_hwecc() as it expects ecc.calculate() to return ECC bytes for just one sector. However, the root cause of the problem is present since v3.9 but was not seen then as NAND buffers were being allocated as one big chunk prior to commit 3deb9979 ("mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset"). Fix the issue by providing a OMAP optimized write_subpage() implementation. Fixes: 62116e51 ("mtd: nand: omap2: Support for hardware BCH error correction.") Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 1c79df1f upstream. This patch fixes a bug during QUEUE_FULL where transport_complete_qf() calls transport_complete_task_attr() after it's already been invoked by target_complete_ok_work() or transport_generic_request_failure() during initial completion, preceeding QUEUE_FULL. This will result in se_device->simple_cmds, se_device->dev_cur_ordered_id and/or se_device->dev_ordered_sync being updated multiple times for a single se_cmd. To address this bug, clear SCF_TASK_ATTR_SET after the first call to transport_complete_task_attr(), and avoid updating SCSI task attribute related counters for any subsequent calls. Also, when a se_cmd is deferred due to ordered tags and executed via target_restart_delayed_cmds(), set CMD_T_SENT before execution matching what target_execute_cmd() does. Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com> Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 3fc9fb13 upstream. This patch fixes a se_cmd->cmd_kref reference leak that can occur when a non immediate TMR is proceeded our of command sequence number order, and CMDSN_LOWER_THAN_EXP is returned by iscsit_sequence_cmd(). To address this bug, call target_put_sess_cmd() during this special case following what iscsit_process_scsi_cmd() does upon CMDSN_LOWER_THAN_EXP. Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Tuomas Tynkkynen authored
commit 8ee03163 upstream. Commit fd2421f5 ("fs/9p: When doing inode lookup compare qid details and inode mode bits.") transformed v9fs_qid_iget() to use iget5_locked() instead of iget_locked(). However, the test() callback is not checking fid.path at all, which means that a lookup in the inode cache can now accidentally locate a completely wrong inode from the same inode hash bucket if the other fields (qid.type and qid.version) match. Fixes: fd2421f5 ("fs/9p: When doing inode lookup compare qid details and inode mode bits.") Reviewed-by:
Latchesar Ionkov <lucho@ionkov.net> Signed-off-by:
Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 11d49e9d upstream. we are advancing sg as we go, so the pages we need to drop in case of error are *before* the current sg. Signed-off-by:
-
Kailang Yang authored
commit 2d7fe618 upstream. It maybe the typo for ALC700 support patch. To fix the bit value on this patch. Fixes: 6fbae35a ("ALSA: hda/realtek - Add support for new codecs ALC700/ALC701/ALC703") Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit c2432466 upstream. We got a regression report about the HD-audio HDMI chmap, where some surround channels are reported as UNKNOWN. The git bisection pointed the culprit at the commit 9b3dc8aa ("ALSA: hda - Register chmap obj as priv data instead of codec"). The story behind scene is like this: - While moving the code out of the legacy HDA to the HDA common place, the patch modifies the code to obtain the chmap array indirectly in a byte array, and it expands it to kctl value array. - At the latter operation, the size of the array is wrongly passed by sizeof() to the pointer. - It can be 4 on 32bit arch, thus too short for 6+ channels. (And that's the reason why it didn't hit other persons; it's 8 on 64bit arch, thus it's usually enough.) The code was further changed meanwhile, but the problem persisted. Let's fix it by correctly evaluating the array size. Fixes: 9b3dc8aa ("ALSA: hda - Register chmap obj as priv data instead of codec") Reported-by:
VDR User <user.vdr@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit 3d4e8303 upstream. Some timer compat ioctls have NULL checks of timer instance with snd_BUG_ON() that bring up WARN_ON() when the debug option is set. Actually the condition can be met in the normal situation and it's confusing and bad to spew kernel warnings with stack trace there. Let's remove snd_BUG_ON() invocation and replace with the simple checks. Also, correct the error code to EBADFD to follow the native ioctl error handling. Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Takashi Iwai authored
commit 0a62d6c9 upstream. The helper functions to parse and look for the clock source, selector and multiplier unit may return the descriptor with a too short length than required, while there is no sanity check in the caller side. Add some sanity checks in the parsers, at least, to guarantee the given descriptor size, for avoiding the potential crashes. Fixes: 79f920fb ("ALSA: usb-audio: parse clock topology of UAC2 devices") Reported-by:
-
Takashi Iwai authored
commit f658f17b upstream. The usb-audio driver may trigger an out-of-bound access at parsing a malformed selector unit, as it checks the header length only after evaluating bNrInPins field, which can be already above the given length. Fix it by adding the length check beforehand. Fixes: 99fc8645 ("ALSA: usb-mixer: parse descriptors with structs") Signed-off-by:
-
Takashi Iwai authored
commit d937cd67 upstream. When the usb-audio descriptor contains the malformed feature unit description with a too short length, the driver may access out-of-bounds. Add a sanity check of the header size at the beginning of parse_audio_feature_unit(). Fixes: 23caaf19 ("ALSA: usb-mixer: Add support for Audio Class v2.0") Reported-by:
-
Henrik Eriksson authored
commit 20e3f985 upstream. commit 3179f620 ("ALSA: core: add .get_time_info") had a side effect of changing the behaviour of the PCM runtime tstamp. Prior to this change tstamp was not updated by snd_pcm_update_hw_ptr0() unless the hw_ptr had moved, after this change tstamp was always updated. For an application using alsa-lib, doing snd_pcm_readi() followed by snd_pcm_status() to estimate the age of the read samples by subtracting status->avail * [sample rate] from status->tstamp this change degraded the accuracy of the estimate on devices where the pcm hw does not provide a granular hw_ptr, e.g., devices using soc-generic-dmaengine-pcm.c and a dma-engine with residue_granularity DMA_RESIDUE_GRANULARITY_DESCRIPTOR. The accuracy of the estimate depended on the latency between the PCM hw completing a period and the driver called snd_pcm_period_elapsed() to notify ALSA core, typically determined by interrupt handling latency. After the change the accuracy of the estimate depended on the latency between the PCM hw completing a period and the application calling snd_pcm_status(), determined by the scheduling of the application process. The maximum error of the estimate is one period length in both cases, but the error average and variance is smaller when it depends on interrupt latency. Instead of always updating tstamp, update it only if audio_tstamp changed. Fixes: 3179f620 ("ALSA: core: add .get_time_info") Suggested-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
Henrik Eriksson <henrik.eriksson@axis.com> Signed-off-by:
-
Theodore Ts'o authored
commit 51e3ae81 upstream. If there are pending writes subject to delayed allocation, then i_size will show size after the writes have completed, while i_disksize contains the value of i_size on the disk (since the writes have not been persisted to disk). If fallocate(2) is called with the FALLOC_FL_KEEP_SIZE flag, either with or without the FALLOC_FL_ZERO_RANGE flag set, and the new size after the fallocate(2) is between i_size and i_disksize, then after a crash, if a journal commit has resulted in the changes made by the fallocate() call to be persisted after a crash, but the delayed allocation write has not resolved itself, i_size would not be updated, and this would cause the following e2fsck complaint: Inode 12, end of extent exceeds allowed value (logical block 33, physical block 33441, len 7) This can only take place on a sparse file, where the fallocate(2) call is allocating blocks in a range which is before a pending delayed allocation write which is extending i_size. Since this situation is quite rare, and the window in which the crash must take place is typically < 30 seconds, in practice this condition will rarely happen. Nevertheless, it can be triggered in testing, and in particular by xfstests generic/456. Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reported-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
-
Rameshwar Prasad Sahu authored
commit f1601113 upstream. When tracing ata link error event, the kernel crashes when the disk is removed due to NULL pointer access by trace_ata_eh_link_autopsy API. This occurs as the dev is NULL when the disk disappeared. This patch fixes this crash by calling trace_ata_eh_link_autopsy only if "dev" is not NULL. v2 changes: Removed direct passing "link" pointer instead of "dev" in trace API. Signed-off-by:
Rameshwar Prasad Sahu <rsahu@apm.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Fixes: 255c03d1 ("libata: Add tracepoints") Signed-off-by:
-
Arnd Bergmann authored
commit 3f2a162f upstream. We set rtlhal->last_suspend_sec to an uninitialized stack variable, but unfortunately gcc never warned about this, I only found it while working on another patch. I opened a gcc bug for this. Presumably the value of rtlhal->last_suspend_sec is not all that important, but it does get used, so we probably want the patch backported to stable kernels. Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Larry Finger authored
commit 519ce2f9 upstream. In routine rtl92ee_set_fw_rsvdpagepkt(), the driver allocates an skb, but never calls rtl_cmd_send_packet(), which will free the buffer. All other rtlwifi drivers perform this operation correctly. This problem has been in the driver since it was included in the kernel. Fortunately, each firmware load only leaks 4 buffers, which likely explains why it has not previously been detected. Signed-off-by:
-
