Currently, ASPM is disabled for all WLAN+BT combo chipsets
when BTCOEX is enabled. This is incorrect since the workaround
is required only for WB195, which is a AR9285+AR3011 combo
solution. Fix this by checking for the HW version when enabling
the workaround.

Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

So says Samuel Ortiz <sameo@linux.intel.com>:

This is the first NFC pull request for the 3.7 merge window.

With this one we get:

- HCI and LLC layers separation. We now can support various LLC
  protocols for HCI drivers, SHDLC being one of them. This will be needed as
  we're planning to support raw HCI chipsets that do the SHDLC encapsulation
  in firmware. So for now we have an SHDLC and a NOP LLC layers.

- pn533 command queueing implementation. This simplifies the pn533 locking
  logic and fixes a kernel warning.

- NCI p2p initiator mode implementation.

- Replace custom workqueues with system ones, for HCI and LLCP.

- Raw pn544 driver removal, as scheduled on the features-removal.txt file.

- A few HCI, SHDLC and LLCP fixes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current regulatory code on cfg80211 performs a check to
see if a regulatory rule belongs to an IEEE band so that if
a Country IE is received and no rules are specified for a
band (which is allowed by IEEE) those bands are left intact.
The current band check assumes a rule is bound to a band
if the rule's start or end frequency is less than 2 GHz
apart from the center of frequency being inspected.

In order to support 60 GHz for 802.11ad we need to increase
this to account for the channel spacing of 2160 MHz whereby
a channel somewhere in the middle of a regulatory rule may
be more than 2 GHz apart from either the beginning or
end of the frequency rule.

Without a fix for this even though channels 1-3 are allowed world
wide on the rule (57240 - 63720 @ 2160), channel 2 at 60480 MHz
will end up getting disabled given that it is 3240 MHz from
both the frequency rule start and end frequency. Fix this by
using 2 GHz separation assumption for the 2.4 and 5 GHz bands
but for 60 GHz use a 10 GHz separation before assuming a rule
is not part of the band.

Since we have no 802.11ad drivers yet merged this change has
no impact to existing Linux upstream device drivers.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

During processing incoming RSET frame chip, possibly due to
its internal timout, can retrnasmit an another RSET which
is next queued for processing in shdlc layer.

In case when we accept processed RSET skip those remaining on
the rcv queue until chip will send it's first S or I frame.
This will mean the chip completed connection as well.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As queue_work() does not guarantee immediate execution of sm_work it
can happen in crossover RSET usecase that connect timer will constantly
change the shdlc state from NEGOTIATING to CONNECTING before shdlc has
chance to handle incoming frame.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Acked-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

xmit callback provided by a driver encapsulates upper layers
data and sends it to the hardware. So, HCI does not know the
exact amount of data being sent and thus can't handle partially
sent frames properly.

Therefore, the driver must return 0 for completely sent frame or
negative for failure.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Acked-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

linux-nfc@lists.01.org is where all the Linux NFC related discussions take
place, and one can also send kernel patches there.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This was scheduled for 3.6, we're late.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The dereference should be moved below the NULL test.

spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

After fixing the LLC Makefile, we no longer need those exports.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The previous shdlc HCI driver and its header are removed from the tree.
PN544 now registers directly with HCI and passes the name of the llc it
requires (shdlc).
HCI instantiation now allocates the required llc instance. The llc is
started when the HCI device is brought up.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is used by HCI drivers such as the one for the pn544 which require
communications between HCI and the chip to use shdlc.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This is a passthrough llc. It can be used by HCI drivers that don't
need link layer control. HCI will then write directly to the driver, and
driver will deliver incoming frames directly to HCI without any
processing.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The LLC layer manages modules that control the link layer protocol (such
as shdlc) between HCI and an HCI driver. The driver must simply specify
the required llc when it registers with HCI.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This enables the completion callback to be called from a different
context, preventing a possible deadlock if the callback resulted in the
invocation of a nested call to the currently locked nfc_dev.
This is also more in line with the im_transceive nfc_ops for NFC Core or
NCI drivers which already behave asynchronously.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This method initiates execution of an HCI cmd. Result will be delivered
through an asynchronous callback.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Make it match the data_exchange_cb_t so that it can be used directly in
the implementation of an asynchronous hci_transceive
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Driver must handle its data added to the frame, so at this point
removeing control field of shdlc frame is enough.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Acked-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Checksum is specific for a chip spcification and it varies
(in size and type) between different hardware. It should be
handled in the driver then.

Moreover, shdlc spec doesn't mention crc as a part of the frame.

Update pn544_hci driver as well.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Acked-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

nfc_llcp_build_tlv() malloced the memory and should be free in
nfc_llcp_build_gb() after used, and the same in the error handling
case, otherwise it will cause memory leak.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As we don't have a primary handler but only a threaded one, __setup_irq()
ends up failing if we don't set this flag.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC driver doesn't sit in memory reclaim path and has no reason to use
WQ_MEM_RECLAIM.  Drop WQ_MEM_RECLAIM from pn533->wq and use
alloc_ordered_workqueue() instead of WQ_UNBOUND w/ max_active == 1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC is using a number of custom ordered workqueues w/ WQ_MEM_RECLAIM.
WQ_MEM_RECLAIM is unnecessary unless NFC is gonna be used as transport
for storage device, and all use cases match one work item to one
ordered workqueue - IOW, there's no actual ordering going on at all
and using system_nrt_wq gives the same behavior.

There's nothing to be gained by using custom workqueues.  Use
system_nrt_wq instead and drop all the custom ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch remove the repeated code for checking llcp_sock &
llcp_sock->dev against NULL.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Simplify the code by make use of module_platform_driver macro.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

During NFC-DEP target activation, store the remote
general bytes to be used later in dep_link_up.
When dep_link_up is called, activate the NFC-DEP target,
and forward the remote general bytes.
When dep_link_down is called, deactivate the target.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If initiator protocol is NFC-DEP, set the local general bytes
in nci_start_poll.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Instead of returning EBUSY when getting a command while another one is
running, we queue them. Upon completion of the pending command, the next
one is processed.
Besides the fact that it simplifies the pn533 locking scheme, it also
comes with the nice side effect of fixing the following warning:

[   82.274297] =====================================
[   82.274297] [ BUG: bad unlock balance detected! ]
[   82.274298] 3.5.0-rc1+ #1 Not tainted
[   82.274299] -------------------------------------
[   82.274300] kworker/u:1/16 is trying to release lock (&dev->cmd_lock) at:
[   82.274305] [<ffffffff8144f246>] mutex_unlock+0x9/0xb
[   82.274305] but there are no more locks to release!
[   82.274306]
[   82.274306] other info that might help us debug this:
[   82.274306] 2 locks held by kworker/u:1/16:
[   82.274311]  #0:  (pn533){.+.+..}, at: [<ffffffff8103a67d>]
+process_one_work+0x145/0x2e2
[   82.274314]  #1:  ((&dev->cmd_work)){+.+...}, at: [<ffffffff8103a67d>]
+process_one_work+0x145/0x2e2
[   82.274314]
[   82.274314] stack backtrace:
[   82.274315] Pid: 16, comm: kworker/u:1 Not tainted 3.5.0-rc1+ #1
[   82.274315] Call Trace:
[   82.274317]  [<ffffffff8144f246>] ? mutex_unlock+0x9/0xb
[   82.274321]  [<ffffffff81059841>] print_unlock_inbalance_bug+0xda/0xe4
[   82.274323]  [<ffffffff8105c74c>] lock_release_non_nested+0xb2/0x232
[   82.274325]  [<ffffffff8105a61e>] ? mark_held_locks+0x6d/0x95
[   82.274326]  [<ffffffff8144f246>] ? mutex_unlock+0x9/0xb
[   82.274328]  [<ffffffff81451105>] ? _raw_spin_unlock_irqrestore+0x40/0x5c
[   82.274329]  [<ffffffff8144f246>] ? mutex_unlock+0x9/0xb
[   82.274330]  [<ffffffff8105ca42>] lock_release+0x176/0x1ac
[   82.274333]  [<ffffffff8123de14>] ? pn533_send_complete+0xa8/0xa8
[   82.274334]  [<ffffffff8144f1d6>] __mutex_unlock_slowpath+0xb0/0x117
[   82.274336]  [<ffffffff8144f246>] mutex_unlock+0x9/0xb
[   82.274337]  [<ffffffff8123de65>] pn533_wq_cmd_complete+0x51/0x55
[   82.274338]  [<ffffffff8103a6db>] process_one_work+0x1a3/0x2e2
[   82.274340]  [<ffffffff8103a67d>] ? process_one_work+0x145/0x2e2
[   82.274341]  [<ffffffff8103b119>] worker_thread+0xcf/0x153
[   82.274343]  [<ffffffff8103b04a>] ? manage_workers.isra.22+0x16b/0x16b
[   82.274344]  [<ffffffff8103b04a>] ? manage_workers.isra.22+0x16b/0x16b
[   82.274346]  [<ffffffff8103eb11>] kthread+0x95/0x9d
[   82.274348]  [<ffffffff81452ef4>] kernel_thread_helper+0x4/0x10
[   82.274351]  [<ffffffff81046561>] ? finish_task_switch+0x45/0xc3
[   82.274352]  [<ffffffff814514f0>] ? retint_restore_args+0x13/0x13
[   82.274353]  [<ffffffff8103ea7c>] ? __init_kthread_worker+0x55/0x55
[   82.274354]  [<ffffffff81452ef0>] ? gs_change+0x13/0x13
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Hardware support for MFP is not available in ath5k. Thus,
this implementation allows the mac80211 stack to do the
actuall crypto operation.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.

While the documentation hints that there's some
hardware support for offloading MFP "decryption",
this simple implementation relies on the mac80211
stack to do the actual crypto operations.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.

Note:

As all current (and old) firmwares corrupt
incoming, protected management frames, the
decryption offloading needs to be disabled.
This will be done automatically if needed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of copying from a constant array
(which is still needed for other purposes)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>