- 19 Jan, 2023 9 commits
-
-
Randy Dunlap authored
Building the kernel documentation causes this warning 7 times. Fix it by adding a " *" line instead of a blank line. drivers/gpu/drm/drm_connector.c:1849: warning: bad line: Fixes: 7d63cd85 ("drm/connector: Add TV standard property") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> CC: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
Simon Ser <contact@emersion.fr> Signed-off-by:
Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20230117070224.30751-1-rdunlap@infradead.org
-
Randy Dunlap authored
Fix a kernel-doc warning and other kernel-doc formatting for drm_atomic_helper_connect_tv_check(). drivers/gpu/drm/drm_atomic_state_helper.c:560: warning: Cannot understand * @drm_atomic_helper_connector_tv_check: Validate an analog TV connector state on line 560 - I thought it was a doc line Fixes: 5a28cefd ("drm/atomic-helper: Add an analog TV atomic_check implementation") Signed-off-by:
-
Alexander Stein authored
The LDB clock needs to be exactly 7-times the pixel clock used by the display. Signed-off-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
-
Biju Das authored
Document RZ/V2L DSI bindings. RZ/V2L MIPI DSI is identical to one found on the RZ/G2L SoC. No driver changes are required as generic compatible string "renesas,rzg2l-mipi-dsi" will be used as a fallback. Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Alexander Stein authored
This helps figuring out why the device probe is deferred. Signed-off-by:
Andrzej Hajda <andrzej.hajda@intel.com> Signed-off-by:
-
Wadim Egorov authored
Switch to gpiod_set_value_cansleep() in sii902x_reset(). This is relevant if the reset line is tied to a I2C GPIO controller. Signed-off-by:
Wadim Egorov <w.egorov@phytec.de> Reviewed-by:
-
Richard Acayan authored
This panel communicates brightness in big endian. This is not a quirk of the panels themselves, but rather, a part of the MIPI standard. Use the new mipi_dsi_dcs_set_display_brightness_large() function that properly handles 16-bit brightness instead of bypassing the brightness functions entirely. Signed-off-by:
Richard Acayan <mailingradian@gmail.com> Reviewed-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
Richard Acayan authored
These panels communicate brightness in big endian. This is not a quirk of the panels themselves, but rather, a part of the MIPI standard. Use the new mipi_dsi_dcs_set_display_brightness_large() function that properly handles 16-bit brightness instead of doing special processing of the brightness values. Signed-off-by:
Caleb Connolly <caleb@connolly.tech> Reviewed-by:
-
Daniel Mentz authored
The MIPI DCS specification demands that brightness values are sent in big endian byte order. It also states that one parameter (i.e. one byte) shall be sent/received for 8 bit wide values, and two parameters shall be used for values that are between 9 and 16 bits wide. Add new functions to properly handle 16-bit brightness in big endian, since the two 8- and 16-bit cases are distinct from each other. [richard: use separate functions instead of switch/case] [richard: split into 16-bit component] Fixes: 1a9d7593 ("drm/dsi: Implement DCS set/get display brightness") Signed-off-by:
Daniel Mentz <danielmentz@google.com> Link: https://android.googlesource.com/kernel/msm/+/754affd62d0ee268c686c53169b1dbb7deac8550 [richard: fix 16-bit brightness_get] Signed-off-by:
-
- 18 Jan, 2023 31 commits
-
-
Christian König authored
Not used anymore by other drivers or TTM itself. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Zack Rusin <zackr@vmware.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221125102137.1801-9-christian.koenig@amd.com
-
Christian König authored
TTM is just wrapping core DMA functionality here, remove the mid-layer. No functional change. Signed-off-by:
Karol Herbst <kherbst@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221125102137.1801-5-christian.koenig@amd.com
-
Dmitry Baryshkov authored
If the bridge is connected using both DSI ports, the driver should use both of them all the time. Correct programming sequence to always use dual-port mode if both dsi0 and dsi1 are connected. Reviewed-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
-
Dmitry Baryshkov authored
The lt9611 bridge can support different modes, it makes no sense to list them in the table. Drop the table and check the number of interfaces using the fixed value. Signed-off-by:
-
Dmitry Baryshkov authored
Rework handling infoframes: - Write full HDMI AVI infoframe instead of just fixing the VIC value - Also send the HDMI Vendor Specific infoframe, as recommended by the HDMI spec. Reviewed-by:
-
Dmitry Baryshkov authored
Inline calculated values to simplify the calculation in lt9611_mipi_video_setup(). Reviewed-by:
-
Dmitry Baryshkov authored
Attaching DVI sink to the lt9611 requires different setup. Fix the register write to make the DVI displays sync onto the correct sync pulse. Reviewed-by:
-
Dmitry Baryshkov authored
The bindings require that there is a next bridge after the lt9611. If nothing else it can be the hdmi-connector (as used on the RB3 platform, see sdm845-db845c.dts). Bring in the next bridge into the drm bridges chain and attach to it. Since lt9611 is not anymore the last bridge in the chain, this also allows us to drop all the !DRM_BRIDGE_ATTACH_NO_CONNECTOR functionality. Reviewed-by:
-
Dmitry Baryshkov authored
The mode_set callback is deprectated for drm_bridges in favour of using atomic_enable callback. Move corresponding code into the function lt9611_bridge_atomic_enable() and turn lt9611_bridge_pre_enable() into the proper atomic_pre_enable callback. Reviewed-by:
-
Dmitry Baryshkov authored
Pass a pointer to the OF node while registering lt9611 MIPI device. Fixes: 23278bf5 ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by:
-
Dmitry Baryshkov authored
Instead of having several fixed values for the pcr register, calculate it before programming. This allows the bridge to support most of the display modes. Fixes: 23278bf5 ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by:
-
Dmitry Baryshkov authored
Program the upper part of the hfront_porch into the proper register. Fixes: 23278bf5 ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by:
-
Dmitry Baryshkov authored
Fix programming of hsync and vsync polarities Fixes: 23278bf5 ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by:
-
Dmitry Baryshkov authored
The driver will reset the bridge in the atomic_pre_enable(). However this will also drop the HPD interrupt state. Instead of resetting the bridge, properly wake it up. This fixes the HPD interrupt delivery after the disable/enable cycle. Fixes: 23278bf5 ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by:
-
Dmitry Baryshkov authored
On atomic_post_disable the bridge goes to the low power state. However the code disables too much of the chip, so the HPD event is not being detected and delivered to the host. Reduce the power saving in order to get the HPD event. Fixes: 23278bf5 ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by:
-
Christian König authored
This interface is not working as it should. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221109095010.141189-5-christian.koenig@amd.com
-
Christian König authored
Remove some not implemented function define Signed-off-by:
-
Nirmoy Das authored
There are no current users of DRM_DEBUG_KMS_RATELIMITED() so remove it. Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
Nirmoy Das <nirmoy.das@intel.com> Reviewed-by:
-
Nirmoy Das authored
Replace deprecated DRM_DEBUG_KMS_RATELIMITED() and DRM_ERROR() with proper APIs. v2: replace pr_err with dev_err(Alex). Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Christian König <christian.koenig@amd.com> Signed-off-by:
-
Thomas Zimmermann authored
Remove most include statements from crm_crtc_helper.h and forward- declare the contained types in drm_crtc_helper.h. Only keep <linux/types.h> for the definition of 'bool'. Suggested-by:
Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Acked-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. v2: * keep includes sorted (Sam) Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Drop drm_crtc_helper.h where possible. v2: * update commit message (Sam) Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Drop drm_crtc_helper.h where possible. v2: * update commit message (Sam) Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Directly include required headers and drop drm_crtc_helper.h where possible. Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Drop drm_crtc_helper.h where possible. v2: * update commit message (Sam) Signed-off-by:
-
Thomas Zimmermann authored
Several source files include drm_crtc_helper.h without needing it or only to get its transitive include statements; leading to unnecessary compile-time dependencies. Drop drm_crtc_helper.h where possible. v2: * update commit message (Sam) Signed-off-by:
-
