This is a refactoring step to be able and store the hash table which
keeps track of offloaded TC flows in a different location for NIC
vs e-switch rules.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When an e-switch TC rule is offloaded through the egdev (egress
device) mechanism, we treat this as egress, all other cases (NIC
and e-switch) are considred ingress.

This is preparation step that will allow us to  identify "wrong"
stat/del offload calls made by the TC core on egdev based flows and
ignore them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When the merged eswitch capability is supported, allow offloading rules
between VFs which belong to different PFs (and hence have different
eswitch affinity).
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

mlx5-updates-2018-05-17

mlx5 core dirver updates for both net-next and rdma-next branches.

From Christophe JAILLET, first three patches to use kvfree where needed.

From: Or Gerlitz <ogerlitz@mellanox.com>

Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.

This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Set a specific source e-switch when setting a rule that matches on the
ingress port.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.

The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Set a specific destination e-switch when setting a destination vport.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When creating FTE, properly distinguish between destination being vport
or tir. The previous code just worked accidentally b/c of both dest being
in the same offset within a union.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
Under merged eswitch, both the matching on source vport and setting
destination vport can have a 2nd attribute which is the vhca id of the
eswitch owner.

For example:
esw0: {match: <src vport=1 owner=0> action: fwd to <dst vport=7, owner=1>}
is a flow set on eswitch0 matching on source vport=1 from his eswitch
and the action being fwd to dest vport=7 of eswitch1.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz Klein <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Florian Fainelli says:

====================
net: Allow more drivers with COMPILE_TEST

This patch series includes more drivers to be build tested with COMPILE_TEST
enabled. This helps cover some of the issues I just ran into with missing
a driver *sigh*.

Chanves in v3:

- drop the TI Keystone NETCP driver from the COMPILE_TEST additions

Changes in v2:

- allow FEC to build outside of CONFIG_ARM/ARM64 by defining a layout of
  registers, this is not meant to run, so this is not a real issue if we
  are not matching the correct register layout
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Those drivers build just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Freescale FEC driver builds fine with COMPILE_TEST, so make that
possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of the TI drivers build just fine with COMPILE_TEST, cpmac (AR7) is
the exception because it uses a header file from
arch/mips/include/asm/mach-ar7/ar7.h and keystone netcp which requires
help from drivers/soc/ti/ for queue management helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add informative messages for error paths related to adding a
VLAN to a device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.

This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.

Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32

HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec

Average:     CPU    %usr   %nice    %sys %iowait    %irq   %soft  %steal  %guest   %idle
Average:     all    0.59    0.00   32.93    0.00    0.00   43.07    0.00    0.00   23.42

HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec

Average:     CPU    %usr   %nice    %sys %iowait    %irq   %soft  %steal  %guest   %idle
Average:     all    0.70    0.00   31.70    0.00    0.00   25.68    0.00    0.00   41.92

HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec

Average:     CPU    %usr   %nice    %sys %iowait    %irq   %soft  %steal  %guest   %idle
Average:     all    0.86    0.00   24.14    0.00    0.00    6.59    0.00    0.00   68.41

HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec

Average:     CPU    %usr   %nice    %sys %iowait    %irq   %soft  %steal  %guest   %idle
Average:     all    0.87    0.00   23.75    0.00    0.00    6.19    0.00    0.00   69.19
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-05-17

This series contains updates to ixgbe, ixgbevf and ice drivers.

Cathy Zhou resolves sparse warnings by using the force attribute.

Mauro S M Rodrigues fixes a bug where IRQs were not freed if a PCI error
recovery system opts to remove the device which causes
ixgbe_io_error_detected() to return PCI_ERS_RESULT_DISCONNECT before
calling ixgbe_close_suspend() which results in IRQs not freed and
crashing when the remove handler calls pci_disable_device().  Resolved
this by calling ixgbe_close_suspend() before evaluating the PCI channel
state.

Pavel Tatashin releases the rtnl_lock during the call to
ixgbe_close_suspend() to allow scaling if device_shutdown() is
multi-threaded.

Emil modifies ixgbe to not validate the MAC address during a reset,
unless the MAC was set on the host so that the VF will get a new MAC
address every time it reloads.  Also updates ixgbevf to set
hw->mac.perm_addr in order to retain the custom MAC on a reset.

Anirudh updates the ice NVM read/erase/update AQ commands to align with
the latest specification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Vlad Buslov <vladbu@mellanox.com>
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We recently refactored this code and introduced a static checker
warning.  Smatch complains that if cmd->index is zero then we would
underflow the arrays.  That's obviously true.

The question is whether we prevent cmd->index from being zero at a
different level.  I've looked at the code and I don't immediately see
a check for that.

Fixes: 062b3e1b ("net/ncsi: Refactor MAC, VLAN filters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzkaller found that following program crashes the host :

{
  int fd = socket(AF_SMC, SOCK_STREAM, 0);
  int val = 1;

  listen(fd, 0);
  shutdown(fd, SHUT_RDWR);
  setsockopt(fd, 6, TCP_NODELAY, &val, 4);
}

Simply initialize conn.tx_work & conn.send_lock at socket creation,
rather than deeper in the stack.

ODEBUG: assert_init not available (active state 0) object type: timer_list hint:           (null)
WARNING: CPU: 1 PID: 13988 at lib/debugobjects.c:329 debug_print_object+0x16a/0x210 lib/debugobjects.c:326
Kernel panic - not syncing: panic_on_warn set ...

CPU: 1 PID: 13988 Comm: syz-executor0 Not tainted 4.17.0-rc4+ #46
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1b9/0x294 lib/dump_stack.c:113
 panic+0x22f/0x4de kernel/panic.c:184
 __warn.cold.8+0x163/0x1b3 kernel/panic.c:536
 report_bug+0x252/0x2d0 lib/bug.c:186
 fixup_bug arch/x86/kernel/traps.c:178 [inline]
 do_error_trap+0x1de/0x490 arch/x86/kernel/traps.c:296
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:315
 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:992
RIP: 0010:debug_print_object+0x16a/0x210 lib/debugobjects.c:326
RSP: 0018:ffff880197a37880 EFLAGS: 00010086
RAX: 0000000000000061 RBX: 0000000000000005 RCX: ffffc90001ed0000
RDX: 0000000000004aaf RSI: ffffffff8160f6f1 RDI: 0000000000000001
RBP: ffff880197a378c0 R08: ffff8801aa7a0080 R09: ffffed003b5e3eb2
R10: ffffed003b5e3eb2 R11: ffff8801daf1f597 R12: 0000000000000001
R13: ffffffff88d96980 R14: ffffffff87fa19a0 R15: ffffffff81666ec0
 debug_object_assert_init+0x309/0x500 lib/debugobjects.c:692
 debug_timer_assert_init kernel/time/timer.c:724 [inline]
 debug_assert_init kernel/time/timer.c:776 [inline]
 del_timer+0x74/0x140 kernel/time/timer.c:1198
 try_to_grab_pending+0x439/0x9a0 kernel/workqueue.c:1223
 mod_delayed_work_on+0x91/0x250 kernel/workqueue.c:1592
 mod_delayed_work include/linux/workqueue.h:541 [inline]
 smc_setsockopt+0x387/0x6d0 net/smc/af_smc.c:1367
 __sys_setsockopt+0x1bd/0x390 net/socket.c:1903
 __do_sys_setsockopt net/socket.c:1914 [inline]
 __se_sys_setsockopt net/socket.c:1911 [inline]
 __x64_sys_setsockopt+0xbe/0x150 net/socket.c:1911
 do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 01d2f7e2 ("net/smc: sockopts TCP_NODELAY and TCP_CORK")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ursula Braun <ubraun@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't store repr pointer to reprs array until the representor is
successfully created. This avoids message about "representor
destruction" even when it was never created. Also it cleans-up the flow.
Also, check return value after port alloc.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: small improvements

Those 3 patches are small improvements to the Marvell PPv2 driver. The
series does not conflict with the one sent about phylink and
1000/2500baseX support, so the two series can live in parallel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Prevent flood of RX error prints during heavy traffic with weak signal
in link by checking net_ratelimit() before using netdev_err().
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: small rework, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove special stop/start handling from the set_mac_address callback.
All this special care is not needed, and can be removed. It also
simplifies the up/down status in the driver and helps avoiding possible
link status mismatch issues.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid repeating the check for free aggregated descriptors when it
already failed at the beginning of the function.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: phylink conversion

This series convert the Marvell PPv2 driver to phylink (models the MAC
to PHY link).

One important point is the PPv2 driver supports two probe modes: device
tree and ACPI. This series only brings phylink support for the device
tree mode, as the ACPI one will need further work. Still, the driver
should be working as before when using ACPI. This split should be
temporary, and was discussed with Marcin (in Cc.) who added ACPI support
to the driver.

Also as the SFP cages on both DB boards can be considered as non-wired.
We thus chose not to describe those SFP cages and we use fixed-link.

The rest of the series uses phylink to add support for 1000BaseX and
2500BaseX modes in the PPv2 driver. To do this, two patches are needed
in the common PHY framework (patches 3 and 4). The last 4 patches modify
the device tree to use the new PPv2 functionalities.

The series has been tested for the device tree mode on the 7040-db,
8040-db and 8040-mcbin boards, to ensure all the interface where working
as expected.

@Dave: patches 7 to 10 should go through the mvebu tree (Gregory in
Cc.) to avoid any conflict with the other mvebu dt patches taken during
this cycle.

The series is based on today's net-next.

Since v2:
  - Removed the SFP description from the DB boards, as their SFP cages
    are wired properly. We now use fixed-link.
  - Because of this rework, split the series in two, so that the SFP
    part is reviewed separately.
  - Small fixes in the phylink patch.
  - Rebased on the latest net-next branch.

Since v1:
  - Chose a different approach to the SFP changes, as the previous ones
    weren't valid and reworked both BD boards device trees.
  - Misc fixes.
  - Added Kishon's acked-by on one patch.
  - Rebaed on latest net-next branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allow the CP110 comphy to configure some lanes in the
2.5G SGMII mode. This mode is quite close to SGMII and uses nearly the
same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds one more generic PHY mode to the phy_mode enum, to allow
configuring generic PHYs to the 2.5G SGMII mode by using the set_mode
callback.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the PPv2 driver to implement phylink helpers, and use phylink in
DT mode. The other mode supported is ACPI, which will need further work
in order to be entirely compatible with phylink.

The MAC and GoP configuration functions were completely moved to fit
into the phylink helpers. When a PHY is always present between the MAC
and the physical port, phylink only is used, but when this is not the
case (the MAC directly is connected to the physical port) the link IRQ
is used to detect changes in the link state and call phylink_mac_change.

The ACPI mode do not uses phylink as of now, and the changes shouldn't
impact its use.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cosmetic patch to align the ethtool functions to ops definitions. This
patch does not change in any way the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.18

The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.

I also merged wireless-drivers due to an iwlwifi patch dependency.

Major changes:

iwlwifi

* implement Traffic Condition Monitor and use it for scan, BT coex and
  to detect when the AP doesn't support UAPSD properly

* some more work for the 22000 family of devices;

* introduce AMSDU rate control offload

qtnfmac

* DFS offload support

rsi

* roaming enhancements

* increase max supported aggregation subframes

* don't advertise 5 GHz support if the device doesn't support it

brcmfmac

* add support for BCM4366E chipset

* add support for bcm43364 wireless chipset

ath10k

* enable temperature reads for QCA6174 and QCA9377

* add firmware memory dump support for QCA9984

* continue adding WCN3990 support via SNOC bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As documented in Documentation/timers/timers-howto.txt,
replace msleep(1) with usleep_range().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce an new common helper to avoid redundancy.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: default RACK loss recovery

This patch set implements the features correspond to the
draft-ietf-tcpm-rack-03 version of the RACK draft.
https://datatracker.ietf.org/meeting/101/materials/slides-101-tcpm-update-on-tcp-rack-00

1. SACK: implement equivalent DUPACK threshold heuristic in RACK to
   replace existing RFC6675 recovery (tcp_mark_head_lost).

2. Non-SACK: simplify RFC6582 NewReno implementation

3. RTO: apply RACK's time-based approach to avoid spuriouly
   marking very recently sent packets lost.

4. with (1)(2)(3), make RACK the exclusive fast recovery mechanism to
   mark losses based on time on S/ACK. Tail loss probe and F-RTO remain
   enabled by default as complementary mechanisms to send probes in
   CA_Open and CA_Loss states. The probes would solicit S/ACKs to trigger
   RACK time-based loss detection.

All Google web and internal servers have been running RACK-only mode
(4) for a while now. a/b experiments indicate RACK/TLP on average
reduces recovery latency by 10% compared to RFC6675. RFC6675
is default-off now but can be enabled by disabling RACK (sysctl
net.ipv4.tcp_recovery=0) for unseen issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

An RTO event indicates the head has not been acked for a long time
after its last (re)transmission. But the other packets are not
necessarily lost if they have been only sent recently (for example
due to application limit). This patch would prohibit marking packets
sent within an RTT to be lost on RTO event, using similar logic in
TCP RACK detection.

Normally the head (SND.UNA) would be marked lost since RTO should
fire strictly after the head was sent. An exception is when the
most recent RACK RTT measurement is larger than the (previous)
RTO. To address this exception the head is always marked lost.

Congestion control interaction: since we may not mark every packet
lost, the congestion window may be more than 1 (inflight plus 1).
But only one packet will be retransmitted after RTO, since
tcp_retransmit_timer() calls tcp_retransmit_skb(...,segs=1). The
connection still performs slow start from one packet (with Cubic
congestion control).

This commit was tested in an A/B test with Google web servers,
and showed a reduction of 2% in (spurious) retransmits post
timeout (SlowStartRetrans), and correspondingly reduced DSACKs
(DSACKIgnoredOld) by 7%.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create and export a new helper tcp_rack_skb_timeout and move tcp_is_rack
to prepare the final RTO change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously when TCP times out, it first updates cwnd and ssthresh,
marks packets lost, and then updates congestion state again. This
was fine because everything not yet delivered is marked lost,
so the inflight is always 0 and cwnd can be safely set to 1 to
retransmit one packet on timeout.

But the inflight may not always be 0 on timeout if TCP changes to
mark packets lost based on packet sent time. Therefore we must
first mark the packet lost, then set the cwnd based on the
(updated) inflight.

This is not a pure refactor. Congestion control may potentially
break if it uses (not yet updated) inflight to compute ssthresh.
Fortunately all existing congestion control modules does not do that.
Also it changes the inflight when CA_LOSS_EVENT is called, and only
westwood processes such an event but does not use inflight.

This change has two other minor side benefits:
1) consistent with Fast Recovery s.t. the inflight is updated
   first before tcp_enter_recovery flips state to CA_Recovery.

2) avoid intertwining loss marking with state update, making the
   code more readable.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor using a new helper, tcp_timeout_mark_loss(), that marks packets
lost upon RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>