The writing of the data should implicitly truncate
the data to 8bits, so do not bother with the ands
in the code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove the cal_CRC as this is basically wrappering the
ether_crc_le function, and is only being used by the
multicast hash table functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The code was using a delay of 8ms, when it should have been
using the EEPROM status flag from the device to indicate the
EEPROM transaction had finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use the netif_msg_*() macros to enable the debugging based
on the board's msg_enable field. The output still goes via
the dev_dbg() macros, so will be tagged and output as
appropriate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

We have a perfectly good version control system, so we do not
need to duplicate change comments in the header for this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Ensure we hold the spinlock whilst the registers and being
modified even though we hold the overall lock. This should
protect against an interrupt happening whilst we are using
the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove the old hack to program an initial EEPROM setting
into the DM9000 as we now have ethtool support for reading
and writing the EEPROM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Allow the msg_enable value to be read and written by
the ethtool interface.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add ethtool support to access the configuration EEPROM
connected to the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add a mutex to serialise access to the chip functions from
entries such as the ethtool and the MII code. This should
reduce the amount of time the spinlock is held to protect
the address register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.

As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

We can use sleeping functions when reading and writing the
PHY registers, so let us sleep instead of busy waiting for
the PHY.

Note, this also fixes a bug reading the PHY where only 100uS
was being used instead of 150uS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The phy read and write routines call udelay() with the board
lock held, and with the posibility of IRQs being disabled. Since
these delays can be up to 500usec, and are only required as we
have to save the chip's address register.

To improve the behaviour, hold the lock whilst we are writing
and then restore the state before the delay and then repeat
the process once the delay has happened.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add support for ethtool operations for the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove the timer based MII phy polling, as this is
currently broken with the new EEPROM code that now
uses mutexes to protect the phy access.

This will need to be replaced in the future by some
form of mutex safe mechanism for reading the MII
phy status.

The replacement has not been done here as changing
this patch, which is early in the sequence has quite
a knock-on effect. Once this series is merged, then
a new presentation of an patch to poll the MII link
status can be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use the flags in the IRQ resource to specify the type of
IRQ being requested, so that systems which do not have
level-based interrupts, or change the interrupt in some
other way can specify this without making an #ifdef mess
in the driver.

This is specifically designed to undo the change in commit
4e4fc05a which hardwires the
type for everyone but blackfin to IRQT_RISING, which breaks
all a number of Simtec boards which use (and setup in the
bootloader) active low IRQs.

Note, although there where originally objections due to
the use of IORESOURCE_IRQ and IRQT_ flags not sharing the
same definition, at least <include/linux/interrupt.h> notes
these are the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Daniel Mack <daniel@caiaq.de>
CC: Bryan Wu <bryan.wu@analog.com>
CC: Alex Landau <landau.alex@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Move to using dev_dbg() and friends for the output of
information to the user.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>

This patch adds a flag to the DM9000 platform data which, when set,
configures the device to use an external PHY.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linuy@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>

This patch splits the receive status in 8bit wide fields and convert the
packet length from little endian to CPU byte order.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	1. Add common code for stopping queue.
	2. No need to call netif_stop_queue followed by netif_wake_queue (and
	   infact a netif_start_queue could have been used instead), instead
	   call stop_queue if required, and remove code under USE_GTS macro.
	3. There is no need to check for netif_queue_stopped, as the network
	   core guarantees that for us (I am sure every driver could remove
	   that check, eg e1000 - I have tested that path a few billion times
	   with about a few hundred thousand qstops but the condition never
	   hit even once).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The e1000 driver stores the content of the PCI resources into
unsigned long's before ioremapping. This breaks on 32 bits
platforms that support 64 bits MMIO resources such as ppc 44x.

This fixes it by removing those temporary variables and passing
directly the result of pci_resource_start/len to ioremap.

The side effect is that I removed the assignments to the netdev
fields mem_start, mem_end and base_addr, which are totally useless
for PCI devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--

 drivers/net/e1000/e1000_main.c |   18 +++++-------------
 1 file changed, 5 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add support for dual network (net_device) interface so that ethernet
and wireless can own separate ethX interfaces.

V2
  - Fix the bug that bringing down and up the interface keeps rx
    disabled.
  - Make 'gelic_net_poll_controller()' extern , as David Woodhouse
    pointed out at the previous submission.
  - Fix weird usage of member names for the rx descriptor chain
V1
  - Export functions which are convenient for both interfaces
  - Move irq allocation/release code to driver probe/remove handlers
    because interfaces share interrupts.
  - Allocate skbs by using dev_alloc_skb() instead of netdev_alloc_skb()
    as the interfaces share the hardware rx queue.
  - Add gelic_port struct in order to abstract dual interface handling
  - Change handlers for hardware queues so that they can handle dual
    {source,destination} interfaces.
  - Use new NAPI functions
This is a prerequisite for the new PS3 wireless support.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add support for interrupt driven port link status detection.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove some ethtool handlers, which duplicate functionality that was already
provided by the common ethtool handlers.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Code cleanup:
 - Use appropriate prefixes for names instead of fixed 'gelic_net'
   so that objects of the functions, variables and constants can be estimated.
 - Remove definitions for IPSec offload to the gelic hardware.  This
   functionality is never supported on PS3.
 - Group constants with enum.
 - Use bitwise constants for interrupt status, instead of bit numbers to
   eliminate shift operations.
 - Style fixes.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Mark the members of the structure for DMA descriptors with proper endian
annotations and use the appropriate accessor macros.
As the gelic driver works only on PS3, all these macros will be
expanded to null.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The device id for lv1_net_set_interrupt_status_indicator() is wrong.
This path would be invoked only in the case of an initialization failure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Updates the 8139too driver to work with recently added
(a724605c) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

To kill the volatiles also switch it to stop poking ISA memory directly
without going through readb and friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Change hard coded 2 to NET_IP_ALIGN.  Added new #define with comments.
Tested amd_64
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

.. and I really need to call it something else.  Maybe it is time to
bring back the weasel series, since weasels always make me feel good
about a kernel.

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
  [ARM] constify function pointer tables
  [ARM] 4823/1: AT91 section fix
  [ARM] 4824/1: pxa: clear RDH bit after any reset
  [ARM] pxa: remove debugging PM: printk
  ARM: OMAP1: Misc clean-up
  ARM: OMAP1: Update defconfigs for omap1
  ARM: OMAP1: Palm Tungsten E board clean-up
  ARM: OMAP1: Use I2C bus registration helper for omap1
  ARM: OMAP1: Remove omap_sram_idle()
  ARM: OMAP1: PM fixes for OMAP1
  ARM: OMAP1: Use MMC multislot structures for Siemens SX1 board
  ARM: OMAP1: Make omap1 use MMC multislot structures
  ARM: OMAP1: Change the comments to C style
  ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
  ARM: OMAP: Add helper module for board specific I2C bus registration
  ARM: OMAP: Add dmtimer support for OMAP3
  ARM: OMAP: Pre-3430 clean-up for dmtimer.c
  ARM: OMAP: Add DMA support for chaining and 3430
  ARM: OMAP: Add 24xx GPIO debounce support
  ARM: OMAP: Get rid of unnecessary ifdefs in GPIO code
  ...

We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86.  Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Thanks to Loic Prylli <loic@myri.com>, who originally proposed
this idea.

Always using legacy configuration mechanism for the legacy config space
and extended mechanism (mmconf) for the extended config space is
a simple and very logical approach. It's supposed to resolve all
known mmconf problems. It still allows per-device quirks (tweaking
dev->cfg_size). It also allows to get rid of mmconf fallback code.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [PKT_SCHED] ematch: Fix build warning.

* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
  hrtimer: don't modify restart_block->fn in restart functions
  hrtimer: fix *rmtp/restarts handling in compat_sys_nanosleep()
  hrtimer: fix *rmtp handling in hrtimer_nanosleep()
  ntp: correct inconsistent interval/tick_length usage

Commit 8811930d ("splice: missing user
pointer access verification") added the proper access_ok() calls to
copy_from_user_mmap_sem() which ensures we can copy the struct iovecs
from userspace to the kernel.

But we also must check whether we can access the actual memory region
pointed to by the struct iovec to fix the access checks properly.
Signed-off-by: Bastian Blank <waldi@debian.org>
Acked-by: Oliver Pinter <oliver.pntr@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>