Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.

Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.

Remove the suspend/resume callback to avoid using the power down mode
completely.

[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf

Fixes: 1a5465f5 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Coverity complains of a possible dereference of a null return value.

   	5. returned_null: kzalloc returns NULL. [show details]
   	6. var_assigned: Assigning: si_data = NULL return value from kzalloc.
488        si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL);
489        cbd.length = cpu_to_le16(data_size);
490
491        dma = dma_map_single(&priv->si->pdev->dev, si_data,
492                             data_size, DMA_FROM_DEVICE);

While this kzalloc() is unlikely to fail, I did notice that the function
returned without unmapping si_data.

Fix this by refactoring the error paths and checking for kzalloc()
failure.

Fixes: 888ae5a3 ("net: enetc: add tc flower psfp offload driver")
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While loading a driver and changing the number of queues, I noticed this
message in the kernel log:

"[253489.070080] Number of in use tx queues changed invalidating tc
mappings. Priority traffic classification disabled!"

But I had no idea what interface was being talked about because this
message used pr_warn().

After investigating, it appears we can use the netdev_* helpers already
defined to create predictably formatted messages, and that already handle
<unknown netdev> cases, in more of the messages in dev.c.

After this change, this message (and others) will look like this:
"[  170.181093] ice 0000:3b:00.0 ens785f0: Number of in use tx queues
changed invalidating tc mappings. Priority traffic classification
disabled!"

One goal here was not to change the message significantly from the
original format so as to not break user's expectations, so I just
changed messages that used pr_* and generally started with %s ==
dev->name.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Convert batman from ether_addr_copy() to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - ether_addr_copy(dev->dev_addr, np)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev->dev_addr will be constant soon, make sure
the qualifier is propagated thru batman-adv.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Coverity complains of unsigned compare against 0. There are 2 cases in
this function:

1821        itp = (irq_holdoff * 1000) / p->desc->qman_256_cycles_per_ns;

CID 121131 (#1 of 1): Unsigned compared against 0 (NO_EFFECT)
unsigned_compare: This less-than-zero comparison of an unsigned value is never true. itp < 0U.
1822        if (itp < 0 || itp > 4096) {
1823                max_holdoff = (p->desc->qman_256_cycles_per_ns * 4096) / 1000;
1824                pr_err("irq_holdoff must be between 0..%dus\n", max_holdoff);
1825                return -EINVAL;
1826        }
1827
    	unsigned_compare: This less-than-zero comparison of an unsigned value is never true. irq_threshold < 0U.
1828        if (irq_threshold >= p->dqrr.dqrr_size || irq_threshold < 0) {
1829                pr_err("irq_threshold must be between 0..%d\n",
1830                       p->dqrr.dqrr_size - 1);
1831                return -EINVAL;
1832        }

Fix this by removing the comparisons altogether as they are incorrect. Zero is
a possible value in either case. Also fix a minor comment typo and update the
2 pr_err() calls to use %u formatting as well as be more precise regarding
the exact error.

Fixes: ed1d2143 ("soc: fsl: dpio: add support for irq coalescing per software portal")
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Roy Pledge <Roy.Pledge@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tidy and organize qca8k setup function from multiple for loop.
Change for loop in bridge leave/join to scan all port and skip cpu port.
No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-10-19

This series contains updates to ice driver only.

Brett implements support for ndo_set_vf_rate allowing for min_tx_rate
and max_tx_rate to be set for a VF.

Jesse updates DIM moderation to improve latency and resolves problems
with reported rate limit and extra software generated interrupts.

Wojciech moves a check for trusted VFs to the correct function,
disables lb_en for switchdev offloads, and refactors ethtool ops due
to differences in support for PF and port representor support.

Cai Huoqing utilizes the helper function devm_add_action_or_reset().

Gustavo A. R. Silva replaces uses of allocation to devm_kcalloc() as
applicable.

Dan Carpenter propagates an error instead of returning success.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
ethernet: manual netdev->dev_addr conversions (part 3)

Manual conversions of Ethernet drivers writing directly
to netdev->dev_addr (part 3 out of 3).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, do the swapping, then
call eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
New RGMII delay DT bindings for the SJA1105 DSA driver

During recent reviews I've been telling people that new MAC drivers
should adopt a certain DT binding format for RGMII delays in order to
avoid conflicting interpretations. Some suggestions were better received
than others, and it appears we are still far from a consensus.

Part of the problem seems to be that there are still drivers that apply
RGMII delays based on an incorrect interpretation of the device tree,
and these serve as a bad example for others.
I happen to maintain one of those drivers and I am able to test it, so I
figure that one of the ways in which I can make a change is to stop
providing a bad example.

Therefore, this series adds support for the "rx-internal-delay-ps" and
"tx-internal-delay-ps" properties inside sja1105 switch port DT nodes,
and if these are present, they will decide what RGMII delays will the
driver apply.

The in-tree device trees are also updated to follow the new format, as
well as the schema validator.

I assume it's okay to get all changes merged in through the same tree
(net-next). Although the DTS changes could be split, if needed - the
driver works with or without them. There is one more DTS which should be
changed, which is in Shawn's tree but not in net-next:
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git/tree/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts?h=for-next
For that, I'd have to send a separate patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change does not fix any functional issue or address any real life
use case that wasn't possible before. It is just a small step in the
process of standardizing the way in which Ethernet MAC drivers may apply
RGMII delays (traditionally these have been applied by PHYs, with no
clear definition of what to do in the case of a fixed-link).

The sja1105 driver used to apply MAC-level RGMII delays on the RX data
lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or
"rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id".
But the standard definitions don't say anything about behaving
differently when the port is in fixed-link vs when it isn't, and the new
device tree bindings are about having a way of applying the delays in a
way that is independent of the phy-mode and of the fixed-link property.

When the {rx,tx}-internal-delay-ps properties are present, use them,
otherwise fall back to the old behavior and warn.

One other thing to note is that the SJA1105 hardware applies a delay
value in degrees rather than in picoseconds (the delay in ps changes
depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at
100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase
shift of the internal delay lines assuming that the device tree meant
gigabit, and we let the hardware scale those according to the link speed.

Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/
Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a schema validator to nxp,sja1105.yaml and to dsa.yaml for explicit
MAC-level RGMII delays. These properties must be per port and must be
present only for a phy-mode that represents RGMII.

We tell dsa.yaml that these port properties might be present, we also
define their valid values for SJA1105. We create a common definition for
the RX and TX valid range, since it's quite a mouthful.

We also modify the example to include the explicit RGMII delay properties.
On the fixed-link ports (in the example, port 4), having these explicit
delays is actually mandatory, since with the new behavior, the driver
shouts that it is interpreting what delays to apply based on phy-mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since a switch is basically a bunch of Ethernet controllers, just
inherit the common schema for one to get stronger type validation of the
properties of a port.

For example, before this change it was valid to have a phy-mode = "xfi"
even if "xfi" is not part of ethernet-controller.yaml, now it is not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All ports require either a phy-handle or a fixed-link, and port 3 in the
example didn't have one. Add it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: sched: fixes after recent qdisc->running changes

First patch fixes a plain bug in qdisc_run_begin().
Second patch removes a pair of atomic operations, increasing performance.
====================

Link: https://lore.kernel.org/r/20211019003402.2110017-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

__QDISC_STATE_RUNNING is only set/cleared from contexts owning qdisc lock.

Thus we can use less expensive bit operations, as we were doing
before commit f9eb8aea ("net_sched: transform qdisc running bit into a seqcount")

Fixes: 29cbcd85 ("net: sched: Remove Qdisc::running sequence counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For non TCQ_F_NOLOCK qdisc, qdisc_run_begin() tries to set
__QDISC_STATE_RUNNING and should return true if the bit was not set.

test_and_set_bit() returns old bit value, therefore we need to invert.

Fixes: 29cbcd85 ("net: sched: Remove Qdisc::running sequence counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Return the error code if ice_eswitch_configure() fails.  Don't return
success.

Fixes: 1c54c839 ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

This patch improves a few things:

- it fixes issue where ethtool -i reports that PR supports
  priv-flags and tests when in fact it does not support them
- instead of using the same functions for both PF and PR ethtool ops,
  this patch introduces separate ops for both cases and internal
  functions with core logic.
- prevent accessing VF VSI while VF is not ready by calling
  ice_check_vf_ready_for_cfg
- all PR specific functions in ethtool.c were moved to one place in
  file
- instead overwriting n_priv_flags in ice_repr_get_drvinfo,
  priv-flags code was moved from __ice_get_drvinfo to ice_get_drvinfo
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently it is not possible to set/unset lb_en and lan_en flags
for advanced rules during their creation. Both flags are enabled
by default. In case of switchdev offloads for egress traffic we
need lb_en to be disabled. Because of that, we work around it by
updating the rule immediately after its creation.

This change allows us to set/unset those flags right away and it
gets rid of old workaround as well. Using ice_adv_rule_flags_info
structure we can pass info about flags we want to be set for
a given advanced rule. Flags are stored in flags_info.act.
Values from act would be used only if act_valid was set to true,
otherwise default values would be used.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Merge issues caused the check for switchdev mode has been inserted
in wrong place. It should be in ice_set_vf_trust not in ice_set_vf_mac.

Trusted VFs are forbidden in switchdev mode because they should
be configured only from the host side.

Fixes: 1c54c839 ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The driver tried to work around missing completion events that occurred
while interrupts are disabled, by triggering a software interrupt
whenever we exit polling (but we had to have polled at least once).

This was causing a *lot* of extra interrupts for some workloads like
NVMe over TCP, which resulted in regressions in performance. It was also
visible when polling didn't prevent interrupts when busy_poll was
enabled.

Fix the extra interrupts by utilizing our previously unused 3rd ITR
(interrupt throttle) index and set it to 20K interrupts per second, and
then trigger a software interrupt within that rate limit.

While here, slightly refactor the code to avoid an overwrite of a local
variable in the case of wb_en = true.

Fixes: b7306b42 ("ice: manage interrupts during poll exit")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

If the adaptive settings are changed with
ethtool -C ethx adaptive-rx off adaptive-tx off
then the interrupt rate limit should be maintained as a user set value,
but only if BOTH adaptive settings are off. Fix a bug where the rate
limit that was being used in adaptive mode was staying set in the
register but was not reported correctly by ethtool -c ethx. Due to long
lines include a small refactor of q_vector variable.

Fixes: b8b47723 ("ice: refactor interrupt moderation writes")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.

In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.

This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).

The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.

Add a new helper for setting rate limit, which will be used more
in a followup patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Replacing dma_pool_alloc/memset() with dma_pool_zalloc()
to simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.

Remove the redundant 'flush_workqueue()' calls.

This was generated with coccinelle:

@@
expression E;
@@
- 	flush_workqueue(E);
	destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCI core code in the pci_call_probe() has a path that doesn't hold
device_lock. It happens because the ->probe() is called through the
workqueue mechanism.

   349 static int pci_call_probe(struct pci_driver *drv, struct pci_dev *dev,
   350                           const struct pci_device_id *id)
   351 {
   352
....
   377         if (cpu < nr_cpu_ids)
   378                 error = work_on_cpu(cpu, local_pci_probe, &ddi);

Luckily enough, the core still ensures that only single flow is executed,
so it safe to remove the assert checks that anyway were added for annotations
purposes.

Fixes: b88f7b12 ("devlink: Annotate devlink API calls")
Reported-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable will be assigned again later in the if condition,
there is no meaning there.

drivers/net/ethernet/broadcom/tg3.c:5750:2 warning:

Value stored to 'current_link_up' is never read.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>