- 08 Jun, 2016 20 commits
-
-
Ville Syrjälä authored
commit 3017cd63 upstream. With netconsole (at least) the pr_err("... disablingn") call can recurse back into the dma-debug code, where it'll try to grab free_entries_lock again. Avoid the problem by doing the printk after dropping the lock. Link: http://lkml.kernel.org/r/1463678421-18683-1-git-send-email-ville.syrjala@linux.intel.comSigned-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicolai Stange authored
commit 935244cd upstream. Currently, in ext4_mb_init(), there's a loop like the following: do { ... offset += 1 << (sb->s_blocksize_bits - i); i++; } while (i <= sb->s_blocksize_bits + 1); Note that the updated offset is used in the loop's next iteration only. However, at the last iteration, that is at i == sb->s_blocksize_bits + 1, the shift count becomes equal to (unsigned)-1 > 31 (c.f. C99 6.5.7(3)) and UBSAN reports UBSAN: Undefined behaviour in fs/ext4/mballoc.c:2621:15 shift exponent 4294967295 is too large for 32-bit type 'int' [...] Call Trace: [<ffffffff818c4d25>] dump_stack+0xbc/0x117 [<ffffffff818c4c69>] ? _atomic_dec_and_lock+0x169/0x169 [<ffffffff819411ab>] ubsan_epilogue+0xd/0x4e [<ffffffff81941cac>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254 [<ffffffff81941ab1>] ? __ubsan_handle_load_invalid_value+0x158/0x158 [<ffffffff814b6dc1>] ? kmem_cache_alloc+0x101/0x390 [<ffffffff816fc13b>] ? ext4_mb_init+0x13b/0xfd0 [<ffffffff814293c7>] ? create_cache+0x57/0x1f0 [<ffffffff8142948a>] ? create_cache+0x11a/0x1f0 [<ffffffff821c2168>] ? mutex_lock+0x38/0x60 [<ffffffff821c23ab>] ? mutex_unlock+0x1b/0x50 [<ffffffff814c26ab>] ? put_online_mems+0x5b/0xc0 [<ffffffff81429677>] ? kmem_cache_create+0x117/0x2c0 [<ffffffff816fcc49>] ext4_mb_init+0xc49/0xfd0 [...] Observe that the mentioned shift exponent, 4294967295, equals (unsigned)-1. Unless compilers start to do some fancy transformations (which at least GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the such calculated value of offset is never used again. Silence UBSAN by introducing another variable, offset_incr, holding the next increment to apply to offset and adjust that one by right shifting it by one position per loop iteration. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161Signed-off-by:
Nicolai Stange <nicstange@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Nicolai Stange authored
commit b5cb316c upstream. Currently, in mb_find_order_for_block(), there's a loop like the following: while (order <= e4b->bd_blkbits + 1) { ... bb += 1 << (e4b->bd_blkbits - order); } Note that the updated bb is used in the loop's next iteration only. However, at the last iteration, that is at order == e4b->bd_blkbits + 1, the shift count becomes negative (c.f. C99 6.5.7(3)) and UBSAN reports UBSAN: Undefined behaviour in fs/ext4/mballoc.c:1281:11 shift exponent -1 is negative [...] Call Trace: [<ffffffff818c4d35>] dump_stack+0xbc/0x117 [<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169 [<ffffffff819411bb>] ubsan_epilogue+0xd/0x4e [<ffffffff81941cbc>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254 [<ffffffff81941ac1>] ? __ubsan_handle_load_invalid_value+0x158/0x158 [<ffffffff816e93a0>] ? ext4_mb_generate_from_pa+0x590/0x590 [<ffffffff816502c8>] ? ext4_read_block_bitmap_nowait+0x598/0xe80 [<ffffffff816e7b7e>] mb_find_order_for_block+0x1ce/0x240 [...] Unless compilers start to do some fancy transformations (which at least GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the such calculated value of bb is never used again. Silence UBSAN by introducing another variable, bb_incr, holding the next increment to apply to bb and adjust that one by right shifting it by one position per loop iteration. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161Signed-off-by:
-
Theodore Ts'o authored
commit c9eb13a9 upstream. If the orphaned inode list contains inode #5, ext4_iget() returns a bad inode (since the bootloader inode should never be referenced directly). Because of the bad inode, we end up processing the inode repeatedly and this hangs the machine. This can be reproduced via: mke2fs -t ext4 /tmp/foo.img 100 debugfs -w -R "ssv last_orphan 5" /tmp/foo.img mount -o loop /tmp/foo.img /mnt (But don't do this if you are using an unpatched kernel if you care about the system staying functional. :-) This bug was found by the port of American Fuzzy Lop into the kernel to find file system problems[1]. (Since it *only* happens if inode #5 shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not surprising that AFL needed two hours before it found it.) [1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf Reported by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
-
Lyude authored
commit 255f0e7c upstream. During boot, MST hotplugs are generally expected (even if no physical hotplugging occurs) and result in DRM's connector topology changing. This means that using num_connector from the current mode configuration can lead to the number of connectors changing under us. This can lead to some nasty scenarios in fbcon: - We allocate an array to the size of dev->mode_config.num_connectors. - MST hotplug occurs, dev->mode_config.num_connectors gets incremented. - We try to loop through each element in the array using the new value of dev->mode_config.num_connectors, and end up going out of bounds since dev->mode_config.num_connectors is now larger then the array we allocated. fb_helper->connector_count however, will always remain consistent while we do a modeset in fb_helper. Note: This is just polish for 4.7, Dave Airlie's drm_connector refcounting fixed these bugs for real. But it's good enough duct-tape for stable kernel backporting, since backporting the refcounting changes is way too invasive. Signed-off-by:
Lyude <cpaul@redhat.com> [danvet: Clarify why we need this. Also remove the now unused "dev" local variable to appease gcc.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.comSigned-off-by:
-
Itai Handler authored
commit 7ccca1d5 upstream. Fix possible out of bounds read, by adding missing comma. The code may read pass the end of the dsi_errors array when the most significant bit (bit #31) in the intr_stat register is set. This bug has been detected using CppCheck (static analysis tool). Signed-off-by:
Itai Handler <itai_handler@hotmail.com> Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by:
-
Tomáš Trnka authored
commit c0cb8bf3 upstream. The length of the GSS MIC token need not be a multiple of four bytes. It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data() would previously only trim mic.len + 4 B. The remaining up to three bytes would then trigger a check in nfs4svc_decode_compoundargs(), leading to a "garbage args" error and mount failure: nfs4svc_decode_compoundargs: compound not properly padded! nfsd: failed to decode arguments! This would prevent older clients using the pre-RFC 4121 MIC format (37-byte MIC including a 9-byte OID) from mounting exports from v3.9+ servers using krb5i. The trimming was introduced by commit 4c190e2f ("sunrpc: trim off trailing checksum before returning decrypted or integrity authenticated buffer"). Fixes: 4c190e2f "unrpc: trim off trailing checksum..." Signed-off-by:
Tomáš Trnka <ttrnka@mail.muni.cz> Acked-by:
Jeff Layton <jlayton@poochiereds.net> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Ross Lagerwall authored
commit f0f39387 upstream. Commit ff1e22e7 ("xen/events: Mask a moving irq") open-coded irq_move_irq() but left out checking if the IRQ is disabled. This broke resuming from suspend since it tries to move a (disabled) irq without holding the IRQ's desc->lock. Fix it by adding in a check for disabled IRQs. The resulting stacktrace was: kernel BUG at /build/linux-UbQGH5/linux-4.4.0/kernel/irq/migration.c:31! invalid opcode: 0000 [#1] SMP Modules linked in: xenfs xen_privcmd ... CPU: 0 PID: 9 Comm: migration/0 Not tainted 4.4.0-22-generic #39-Ubuntu Hardware name: Xen HVM domU, BIOS 4.6.1-xs125180 05/04/2016 task: ffff88003d75ee00 ti: ffff88003d7bc000 task.ti: ffff88003d7bc000 RIP: 0010:[<ffffffff810e26e2>] [<ffffffff810e26e2>] irq_move_masked_irq+0xd2/0xe0 RSP: 0018:ffff88003d7bfc50 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffff88003d40ba00 RCX: 0000000000000001 RDX: 0000000000000001 RSI: 0000000000000100 RDI: ffff88003d40bad8 RBP: ffff88003d7bfc68 R08: 0000000000000000 R09: ffff88003d000000 R10: 0000000000000000 R11: 000000000000023c R12: ffff88003d40bad0 R13: ffffffff81f3a4a0 R14: 0000000000000010 R15: 00000000ffffffff FS: 0000000000000000(0000) GS:ffff88003da00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fd4264de624 CR3: 0000000037922000 CR4: 00000000003406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Stack: ffff88003d40ba38 0000000000000024 0000000000000000 ffff88003d7bfca0 ffffffff814c8d92 00000010813ef89d 00000000805ea732 0000000000000009 0000000000000024 ffff88003cc39b80 ffff88003d7bfce0 ffffffff814c8f66 Call Trace: [<ffffffff814c8d92>] eoi_pirq+0xb2/0xf0 [<ffffffff814c8f66>] __startup_pirq+0xe6/0x150 [<ffffffff814ca659>] xen_irq_resume+0x319/0x360 [<ffffffff814c7e75>] xen_suspend+0xb5/0x180 [<ffffffff81120155>] multi_cpu_stop+0xb5/0xe0 [<ffffffff811200a0>] ? cpu_stop_queue_work+0x80/0x80 [<ffffffff811203d0>] cpu_stopper_thread+0xb0/0x140 [<ffffffff810a94e6>] ? finish_task_switch+0x76/0x220 [<ffffffff810ca731>] ? __raw_callee_save___pv_queued_spin_unlock+0x11/0x20 [<ffffffff810a3935>] smpboot_thread_fn+0x105/0x160 [<ffffffff810a3830>] ? sort_range+0x30/0x30 [<ffffffff810a0588>] kthread+0xd8/0xf0 [<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0 [<ffffffff8182568f>] ret_from_fork+0x3f/0x70 [<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0 Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Hari Bathini authored
commit 8ed8ab40 upstream. Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Signed-off-by:
Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Ben Hutchings authored
commit feae3ca2 upstream. Quoting the RHEL advisory: > It was found that the fix for CVE-2015-1805 incorrectly kept buffer > offset and buffer length in sync on a failed atomic read, potentially > resulting in a pipe buffer state corruption. A local, unprivileged user > could use this flaw to crash the system or leak kernel memory to user > space. (CVE-2016-0774, Moderate) The same flawed fix was applied to stable branches from 2.6.32.y to 3.14.y inclusive, and I was able to reproduce the issue on 3.2.y. We need to give pipe_iov_copy_to_user() a separate offset variable and only update the buffer offset if it succeeds. References: https://rhn.redhat.com/errata/RHSA-2016-0103.htmlSigned-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
-
wang yanqing authored
commit 873ffe15 upstream. In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), the tests for enter/exit power-save mode were inverted. With this change applied, the wifi connection becomes much more stable. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by:
Wang YanQing <udknight@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Prarit Bhargava authored
commit ad67b437 upstream. b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with the PCI spec. But it didn't do anything for expansion ROM BARs, so we still try to size them, resulting in warnings like this on Broadwell-EP: pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref] Move the non-compliant BAR check from __pci_read_base() up to pci_read_bases() so it applies to the expansion ROM BAR as well as to BARs 0-5. Note that direct callers of __pci_read_base(), like sriov_init(), will now bypass this check. We haven't had reports of devices with broken SR-IOV BARs yet. [bhelgaas: changelog] Fixes: b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Ricky Liang authored
commit affa80bd upstream. When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS ioctl needs to be treated with special care, as it has the pointer size encoded in the command. Signed-off-by:
Ricky Liang <jcliang@chromium.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Matthias Schiffer authored
commit f5b556c9 upstream. This makes the ath79 bootconsole behave the same way as the generic 8250 bootconsole. Also waiting for TEMT (transmit buffer is empty) instead of just THRE (transmit buffer is not full) ensures that all characters have been transmitted before the real serial driver starts reconfiguring the serial controller (which would sometimes result in garbage being transmitted.) This change does not cause a visible performance loss. In addition, this seems to fix a hang observed in certain configurations on many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver. A more complete follow-up patch will disable 8250 autoconfig for ath79 altogether (the serial controller is detected as a 16550A, which is not fully compatible with the ath79 serial, and the autoconfig may lead to undefined behavior on ath79.) Signed-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by:
-
James Hogan authored
commit 5daebc47 upstream. Commit 85efde6f ("make exported headers use strict posix types") changed the asm-generic siginfo.h to use the __kernel_* types, and commit 3a471cbc ("remove __KERNEL_STRICT_NAMES") make the internal types accessible only to the kernel, but the MIPS implementation hasn't been updated to match. Switch to proper types now so that the exported asm/siginfo.h won't produce quite so many compiler errors when included alone by a user program. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Christopher Ferris <cferris@google.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/12477/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Paul Burton authored
commit ab4a92e6 upstream. When emulating a jalr instruction with rd == $0, the code in isBranchInstr was incorrectly writing to GPR $0 which should actually always remain zeroed. This would lead to any further instructions emulated which use $0 operating on a bogus value until the task is next context switched, at which point the value of $0 in the task context would be restored to the correct zero by a store in SAVE_SOME. Fix this by not writing to rd if it is $0. Fixes: 102cedc3 ("MIPS: microMIPS: Floating point support.") Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13160/Signed-off-by:
-
- 01 Jun, 2016 20 commits
-
-
Greg Kroah-Hartman authored
-
Chanwoo Choi authored
commit b8995f52 upstream. This patch fixes the broken serial log when changing the clock source of uart device. Before disabling the original clock source, this patch enables the new clock source to protect the clock off state for a split second. Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com>
-
Jiri Slaby authored
commit 6798df4c upstream. When csw->con_startup() fails in do_register_con_driver, we return no error (i.e. 0). This was changed back in 2006 by commit 3e795de7. Before that we used to return -ENODEV. So fix the return value to be -ENODEV in that case again. Fixes: 3e795de7 ("VT binding: Add binding/unbinding support for the VT console") Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Reported-by:
"Dan Carpenter" <dan.carpenter@oracle.com> Signed-off-by:
-
Schemmel Hans-Christoph authored
commit 444f94e9 upstream. Added support for Gemalto's Cinterion PH8 and AHxx products with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface. In addition some minor renaming and formatting. Signed-off-by:
Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> [johan: sort current entries and trim trailing whitespace ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit c8d62957 upstream. URBs and buffers allocated in attach for Epic devices would never be deallocated in case of a later probe error (e.g. failure to allocate minor numbers) as disconnect is then never called. Fix by moving deallocation to release and making sure that the URBs are first unlinked. Fixes: f9c99bb8 ("USB: usb-serial: replace shutdown with disconnect, release") Signed-off-by:
-
Johan Hovold authored
commit c5c0c555 upstream. Private data, URBs and buffers allocated for Epic devices during attach were never released on errors (e.g. missing endpoints). Fixes: 6e8cf775 ("USB: add EPIC support to the io_edgeport driver") Signed-off-by:
-
Johan Hovold authored
commit 028c49f5 upstream. The interface read URB is submitted in attach, but was only unlinked by the driver at disconnect. In case of a late probe error (e.g. due to failed minor allocation), disconnect is never called and we would end up with active URBs for an unbound interface. This in turn could lead to deallocated memory being dereferenced in the completion callback. Fixes: f7a33e60 ("USB: serial: add quatech2 usb to serial driver") Signed-off-by:
-
Johan Hovold authored
commit 35be1a71 upstream. The interface instat and indat URBs were submitted in attach, but never unlinked in release before deallocating the corresponding transfer buffers. In the case of a late probe error (e.g. due to failed minor allocation), disconnect would not have been called before release, causing the buffers to be freed while the URBs are still in use. We'd also end up with active URBs for an unbound interface. Fixes: f9c99bb8 ("USB: usb-serial: replace shutdown with disconnect, release") Signed-off-by:
-
Johan Hovold authored
commit 9e452849 upstream. The interface read and event URBs are submitted in attach, but were never explicitly unlinked by the driver. Instead the URBs would have been killed by usb-serial core on disconnect. In case of a late probe error (e.g. due to failed minor allocation), disconnect is never called and we could end up with active URBs for an unbound interface. This in turn could lead to deallocated memory being dereferenced in the completion callbacks. Fixes: ee467a1f ("USB: serial: add Moxa UPORT 12XX/14XX/16XX driver") Signed-off-by:
-
Jiri Slaby authored
commit 13407376 upstream. The write handler allocates skbs and queues them into data->readq. Read side should read them, if there is any. If there is none, skbs should be dropped by hdev->flush. But this happens only if the device is HCI_UP, i.e. hdev->power_on work was triggered already. When it was not, skbs stay allocated in the queue when /dev/vhci is closed. So purge the queue in ->release. Program to reproduce: #include <err.h> #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/stat.h> #include <sys/types.h> #include <sys/uio.h> int main() { char buf[] = { 0xff, 0 }; struct iovec iov = { .iov_base = buf, .iov_len = sizeof(buf), }; int fd; while (1) { fd = open("/dev/vhci", O_RDWR); if (fd < 0) err(1, "open"); usleep(50); if (writev(fd, &iov, 1) < 0) err(1, "writev"); usleep(50); close(fd); } return 0; } Result: kmemleak: 4609 new suspected memory leaks unreferenced object 0xffff88059f4d5440 (size 232): comm "vhci", pid 1084, jiffies 4294912542 (age 37569.296s) hex dump (first 32 bytes): 20 f0 23 87 05 88 ff ff 20 f0 23 87 05 88 ff ff .#..... .#..... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: ... [<ffffffff81ece010>] __alloc_skb+0x0/0x5a0 [<ffffffffa021886c>] vhci_create_device+0x5c/0x580 [hci_vhci] [<ffffffffa0219436>] vhci_write+0x306/0x4c8 [hci_vhci] Fixes: 23424c0d (Bluetooth: Add support creating virtual AMP controllers) Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Matt Gumbel authored
commit 32ecd320 upstream. 008GE0 Toshiba mmc in some Intel Baytrail tablets responds to MMC_SEND_EXT_CSD in 450-600ms. This patch will... () Increase the long read time quirk timeout from 300ms to 600ms. Original author of that quirk says 300ms was only a guess and that the number may need to be raised in the future. () Add this specific MMC to the quirk Signed-off-by:
Matt Gumbel <matthew.k.gumbel@intel.com> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Lv Zheng authored
commit 30c9bb0d upstream. The order of the _OSI related functionalities is as follows: acpi_blacklisted() acpi_dmi_osi_linux() acpi_osi_setup() acpi_osi_setup() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< parse_args() __setup("acpi_osi=") acpi_osi_setup_linux() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< acpi_early_init() acpi_initialize_subsystem() acpi_ut_initialize_interfaces() ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ acpi_bus_init() acpi_os_initialize1() acpi_install_interface_handler(acpi_osi_handler) acpi_osi_setup_late() acpi_update_interfaces() for "!" >>>>>>>>>>>>>>>>>>>>>>>> acpi_osi_handler() Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command line setting can override the DMI detection. That's why acpi_blacklisted() is put before __setup("acpi_osi="). Then we can notice the following wrong invocation order. There are acpi_update_interfaces() (marked by <<<<) calls invoked before acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible to use acpi_osi=!* correctly from OSI DMI table or from the command line. The use of acpi_osi=!* is meant to disable both ACPICA (acpi_gbl_supported_interfaces) and Linux specific strings (osi_setup_entries) while the ACPICA part should have stopped working because of the order issue. This patch fixes this issue by moving acpi_update_interfaces() to where it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux specific strings are still handled in the original place in order to make the following command line working: acpi_osi=!* acpi_osi="Module Device". Note that since acpi_osi=!* is meant to further disable linux specific string comparing to the acpi_osi=!, there is no such use case in our bug fixing work and hence there is no one using acpi_osi=!* either from the command line or from the DMI quirks, this issue is just a theoretical issue. Fixes: 741d8128 (ACPI: Add facility to remove all _OSI strings) Tested-by:
Lukas Wunner <lukas@wunner.de> Tested-by:
Chen Yu <yu.c.chen@intel.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
-
Adrian Hunter authored
commit 1c447116 upstream. Some eMMCs set the partition switch timeout too low. Now typically eMMCs are considered a critical component (e.g. because they store the root file system) and consequently are expected to be reliable. Thus we can neglect the use case where eMMCs can't switch reliably and we might want a lower timeout to facilitate speedy recovery. Although we could employ a quirk for the cards that are affected (if we could identify them all), as described above, there is little benefit to having a low timeout, so instead simply set a minimum timeout. The minimum is set to 300ms somewhat arbitrarily - the examples that have been seen had a timeout of 10ms but were sometimes taking 60-70ms. Signed-off-by:
-
Roger Quadros authored
commit b49b927f upstream. We shouldn't be calling clk_prepare_enable()/clk_prepare_disable() in an atomic context. Fixes the following issue: [ 5.830970] ehci-omap: OMAP-EHCI Host Controller driver [ 5.830974] driver_register 'ehci-omap' [ 5.895849] driver_register 'wl1271_sdio' [ 5.896870] BUG: scheduling while atomic: udevd/994/0x00000002 [ 5.896876] 4 locks held by udevd/994: [ 5.896904] #0: (&dev->mutex){......}, at: [<c049597c>] __driver_attach+0x60/0xac [ 5.896923] #1: (&dev->mutex){......}, at: [<c049598c>] __driver_attach+0x70/0xac [ 5.896946] #2: (tll_lock){+.+...}, at: [<c04c2630>] omap_tll_enable+0x2c/0xd0 [ 5.896966] #3: (prepare_lock){+.+...}, at: [<c05ce9c8>] clk_prepare_lock+0x48/0xe0 [ 5.897042] Modules linked in: wlcore_sdio(+) ehci_omap(+) dwc3_omap snd_soc_ts3a225e leds_is31fl319x bq27xxx_battery_i2c tsc2007 bq27xxx_battery bq2429x_charger ina2xx tca8418_keypad as5013 leds_tca6507 twl6040_vibra gpio_twl6040 bmp085_i2c(+) palmas_gpadc usb3503 palmas_pwrbutton bmg160_i2c(+) bmp085 bma150(+) bmg160_core bmp280 input_polldev snd_soc_omap_mcbsp snd_soc_omap_mcpdm snd_soc_omap snd_pcm_dmaengine [ 5.897048] Preemption disabled at:[< (null)>] (null) [ 5.897051] [ 5.897059] CPU: 0 PID: 994 Comm: udevd Not tainted 4.6.0-rc5-letux+ #233 [ 5.897062] Hardware name: Generic OMAP5 (Flattened Device Tree) [ 5.897076] [<c010e714>] (unwind_backtrace) from [<c010af34>] (show_stack+0x10/0x14) [ 5.897087] [<c010af34>] (show_stack) from [<c040aa7c>] (dump_stack+0x88/0xc0) [ 5.897099] [<c040aa7c>] (dump_stack) from [<c020c558>] (__schedule_bug+0xac/0xd0) [ 5.897111] [<c020c558>] (__schedule_bug) from [<c06f3d44>] (__schedule+0x88/0x7e4) [ 5.897120] [<c06f3d44>] (__schedule) from [<c06f46d8>] (schedule+0x9c/0xc0) [ 5.897129] [<c06f46d8>] (schedule) from [<c06f4904>] (schedule_preempt_disabled+0x14/0x20) [ 5.897140] [<c06f4904>] (schedule_preempt_disabled) from [<c06f64e4>] (mutex_lock_nested+0x258/0x43c) [ 5.897150] [<c06f64e4>] (mutex_lock_nested) from [<c05ce9c8>] (clk_prepare_lock+0x48/0xe0) [ 5.897160] [<c05ce9c8>] (clk_prepare_lock) from [<c05d0e7c>] (clk_prepare+0x10/0x28) [ 5.897169] [<c05d0e7c>] (clk_prepare) from [<c04c2668>] (omap_tll_enable+0x64/0xd0) [ 5.897180] [<c04c2668>] (omap_tll_enable) from [<c04c1728>] (usbhs_runtime_resume+0x18/0x17c) [ 5.897192] [<c04c1728>] (usbhs_runtime_resume) from [<c049d404>] (pm_generic_runtime_resume+0x2c/0x40) [ 5.897202] [<c049d404>] (pm_generic_runtime_resume) from [<c049f180>] (__rpm_callback+0x38/0x68) [ 5.897210] [<c049f180>] (__rpm_callback) from [<c049f220>] (rpm_callback+0x70/0x88) [ 5.897218] [<c049f220>] (rpm_callback) from [<c04a0a00>] (rpm_resume+0x4ec/0x7ec) [ 5.897227] [<c04a0a00>] (rpm_resume) from [<c04a0f48>] (__pm_runtime_resume+0x4c/0x64) [ 5.897236] [<c04a0f48>] (__pm_runtime_resume) from [<c04958dc>] (driver_probe_device+0x30/0x70) [ 5.897246] [<c04958dc>] (driver_probe_device) from [<c04959a4>] (__driver_attach+0x88/0xac) [ 5.897256] [<c04959a4>] (__driver_attach) from [<c04940f8>] (bus_for_each_dev+0x50/0x84) [ 5.897267] [<c04940f8>] (bus_for_each_dev) from [<c0494e40>] (bus_add_driver+0xcc/0x1e4) [ 5.897276] [<c0494e40>] (bus_add_driver) from [<c0496914>] (driver_register+0xac/0xf4) [ 5.897286] [<c0496914>] (driver_register) from [<c01018e0>] (do_one_initcall+0x100/0x1b8) [ 5.897296] [<c01018e0>] (do_one_initcall) from [<c01c7a54>] (do_init_module+0x58/0x1c0) [ 5.897304] [<c01c7a54>] (do_init_module) from [<c01c8a3c>] (SyS_finit_module+0x88/0x90) [ 5.897313] [<c01c8a3c>] (SyS_finit_module) from [<c0107120>] (ret_fast_syscall+0x0/0x1c) [ 5.912697] ------------[ cut here ]------------ [ 5.912711] WARNING: CPU: 0 PID: 994 at kernel/sched/core.c:2996 _raw_spin_unlock+0x28/0x58 [ 5.912717] DEBUG_LOCKS_WARN_ON(val > preempt_count()) Reported-by:
H. Nikolaus Schaller <hns@goldelico.com> Tested-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Catalin Vasile authored
commit e930c765 upstream. caam_jr_alloc() used to return NULL if a JR device could not be allocated for a session. In turn, every user of this function used IS_ERR() function to verify if anything went wrong, which does NOT look for NULL values. This made the kernel crash if the sanity check failed, because the driver continued to think it had allocated a valid JR dev instance to the session and at some point it tries to do a caam_jr_free() on a NULL JR dev pointer. This patch is a fix for this issue. Signed-off-by:
Catalin Vasile <cata.vasile@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 59643d15 upstream. If the size passed to ring_buffer_resize() is greater than MAX_LONG - BUF_PAGE_SIZE then the DIV_ROUND_UP() will return zero. Here's the details: # echo 18014398509481980 > /sys/kernel/debug/tracing/buffer_size_kb tracing_entries_write() processes this and converts kb to bytes. 18014398509481980 << 10 = 18446744073709547520 and this is passed to ring_buffer_resize() as unsigned long size. size = DIV_ROUND_UP(size, BUF_PAGE_SIZE); Where DIV_ROUND_UP(a, b) is (a + b - 1)/b BUF_PAGE_SIZE is 4080 and here 18446744073709547520 + 4080 - 1 = 18446744073709551599 where 18446744073709551599 is still smaller than 2^64 2^64 - 18446744073709551599 = 17 But now 18446744073709551599 / 4080 = 4521260802379792 and size = size * 4080 = 18446744073709551360 This is checked to make sure its still greater than 2 * 4080, which it is. Then we convert to the number of buffer pages needed. nr_page = DIV_ROUND_UP(size, BUF_PAGE_SIZE) but this time size is 18446744073709551360 and 2^64 - (18446744073709551360 + 4080 - 1) = -3823 Thus it overflows and the resulting number is less than 4080, which makes 3823 / 4080 = 0 an nr_pages is set to this. As we already checked against the minimum that nr_pages may be, this causes the logic to fail as well, and we crash the kernel. There's no reason to have the two DIV_ROUND_UP() (that's just result of historical code changes), clean up the code and fix this bug. Fixes: 83f40318 ("ring-buffer: Make removal of ring buffer pages atomic") Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit 9b94a8fb upstream. The size variable to change the ring buffer in ftrace is a long. The nr_pages used to update the ring buffer based on the size is int. On 64 bit machines this can cause an overflow problem. For example, the following will cause the ring buffer to crash: # cd /sys/kernel/debug/tracing # echo 10 > buffer_size_kb # echo 8556384240 > buffer_size_kb Then you get the warning of: WARNING: CPU: 1 PID: 318 at kernel/trace/ring_buffer.c:1527 rb_update_pages+0x22f/0x260 Which is: RB_WARN_ON(cpu_buffer, nr_removed); Note each ring buffer page holds 4080 bytes. This is because: 1) 10 causes the ring buffer to have 3 pages. (10kb requires 3 * 4080 pages to hold) 2) (2^31 / 2^10 + 1) * 4080 = 8556384240 The value written into buffer_size_kb is shifted by 10 and then passed to ring_buffer_resize(). 8556384240 * 2^10 = 8761737461760 3) The size passed to ring_buffer_resize() is then divided by BUF_PAGE_SIZE which is 4080. 8761737461760 / 4080 = 2147484672 4) nr_pages is subtracted from the current nr_pages (3) and we get: 2147484669. This value is saved in a signed integer nr_pages_to_update 5) 2147484669 is greater than 2^31 but smaller than 2^32, a signed int turns into the value of -2147482627 6) As the value is a negative number, in update_pages_handler() it is negated and passed to rb_remove_pages() and 2147482627 pages will be removed, which is much larger than 3 and it causes the warning because not all the pages asked to be removed were removed. Link: https://bugzilla.kernel.org/show_bug.cgi?id=118001 Fixes: 7a8e76a3 ("tracing: unified trace buffer") Reported-by:
Hao Qin <QEver.cn@gmail.com> Signed-off-by:
-
Stefan Metzmacher authored
commit cfda35d9 upstream. See [MS-NLMP] 3.2.5.1.2 Server Receives an AUTHENTICATE_MESSAGE from the Client: ... Set NullSession to FALSE If (AUTHENTICATE_MESSAGE.UserNameLen == 0 AND AUTHENTICATE_MESSAGE.NtChallengeResponse.Length == 0 AND (AUTHENTICATE_MESSAGE.LmChallengeResponse == Z(1) OR AUTHENTICATE_MESSAGE.LmChallengeResponse.Length == 0)) -- Special case: client requested anonymous authentication Set NullSession to TRUE ... Only server which map unknown users to guest will allow access using a non-null NTChallengeResponse. For Samba it's the "map to guest = bad user" option. BUG: https://bugzilla.samba.org/show_bug.cgi?id=11913Signed-off-by:
Stefan Metzmacher <metze@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Steve French authored
commit 897fba11 upstream. Wrong return code was being returned on SMB3 rmdir of non-empty directory. For SMB3 (unlike for cifs), we attempt to delete a directory by set of delete on close flag on the open. Windows clients set this flag via a set info (SET_FILE_DISPOSITION to set this flag) which properly checks if the directory is empty. With this patch on smb3 mounts we correctly return "DIRECTORY NOT EMPTY" on attempts to remove a non-empty directory. Signed-off-by:
Steve French <steve.french@primarydata.com> Acked-by:
Sachin Prabhu <sprabhu@redhat.com> Signed-off-by:
-
Marc Zyngier authored
commit d4b9e079 upstream. The ARM architecture mandates that when changing a page table entry from a valid entry to another valid entry, an invalid entry is first written, TLB invalidated, and only then the new entry being written. The current code doesn't respect this, directly writing the new entry and only then invalidating TLBs. Let's fix it up. Reported-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
