This patch implements ni_ao_cmd much more closely organized like NI MHDDK
examples and DAQ-STC pseudo-code.  Adds comments with some more specific
references to the DAQ-STC.

For stop_src==TRIG_NONE (continuous output mode of entire buffer), the
count for the UC counter was corrected to represent the maximum count
possible (0xffffff).  Prior behavior for stop_src=TRIG_NONE did not
actually follow the DAQ-STC.  Furthermore, stop_src==TRIG_NONE now
correctly uses code specialized for either m-series or e-series devices.

It should be noted that stop_src==TRIG_NONE does _not_ with this patch
(or with prior behavior in ni_mio_common) actually implement true
continuous output.  Rather, the output is simply configured to operate as a
single buffer output, but where the buffer is as large as is possible with
NI-STC hardware.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bits NISTC_AO_CMD1_DAC0_UPDATE_MODE and NISTC_AO_CMD1_DAC1_UPDATE_MODE are
now saved in the local copy of the AO_CMD1 register.  This is more
appropriate than prior methods of setting these bits specifically _both_
in the ni_ao_cmd configuration function _and_ the ni_ao_inttrig trigger
function.  With this patch, the bits are only specifically called out now
in the ni_ao_cmd configuration function.  In the ni_ao_inttrig trigger
function, only the UI_ARM, UC_ARM, BC_ARM bits of the ao_cmd1 register are
specifically called out.  Each of these bits is a strobe bit, while the
DAC[0-1]_UPDATE_MODE bits are simple write bits.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch implements ni_ao_reset much more closely organized like NI MHDDK
examples and DAQ-STC pseudo-code.  Adds comments with some more specific
references to the DAQ-STC.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This change enables the mite DMA controller to only transfer the amount of
data needed by a command.  By default, the old behavior of transferring the
entire comedi DMA data buffer is still in effect.  These changes allow a
command to only transmit a limited portion of that data buffer as needed.

This patch begins to reinterprets stop_arg when stop_src == TRIG_NONE to
allow the user to specify the length of the buffer that should be repeated.
The intent is to allow a user to have a specific buffer repeated as-is
indefinitely.  The contents of the DMA buffer can be left static or changed
by the user via mmap access to the DMA buffer.  If the contents are changed
by the user, additional munging is not performed by the driver and only a
single call to comedi_mark_buffer_written should be done.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Generally, the CR_CHAN macro is/should be used to access the relevant bits
for channel identification in cmd->*_arg when the corresponding
cmd->*_src==TRIG_EXT, including cmd->convert_arg in this case.

This patch does not fix a bug per se, as NISTC_AI_MODE1_CONVERT_SRC() already
masks the value sufficiently, but using CR_CHAN() here makes the code clearer as
it avoids passing some irrelevant bits to NISTC_AI_MODE1_CONVERT_SRC() in the
first place.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes a bug in function ni_tio_input_inttrig().  The trigger number
should be compared to cmd->start_arg, not cmd->start_src.

Fixes: 6a760394 ("staging: comedi: ni_tiocmd: clarify the cmd->start_arg validation and use")
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As suggested by checkpatch.pl, this patch replaces bit shifting on 1 with the
BIT(x) macro.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are race condition B/T ion_client_destroy and debugfs callbacks.
Let's use a mutex to synchronize them.
Signed-off-by: Neil Zhang <neilzhang1123@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently we can only import dma buf fd's to get ion_handle.
Adding support to import dma buf handles to support kernel
specific use cases.

An example use case is in linux platforms such as Tizen, in which
DRM-GEM is used for buffer management for graphics. It has gem_handle
corresponding to a buffer and uses gem_name for sharing the buffer
with other processes. However,it also uses dma_buf fd for 3d operations.
For wayland, there are multiple calls for gem_handle to dma_buf fd
conversion. So, we store dma_buf associated with buffer. But, there is
no api for getting ion_handle from dma_buf. This patch exposes api to
retrieve the ion handle from dma_buf for similar use cases. With this
patch, we can integrate ION within DRM-GEM for buffer management and
dma_buf sharing.
Signed-off-by: Rohit kumar <rohit.kr@samsung.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After removing driver_data struct sync_fence_info has now a fixed size,
thus it doesn't need any field to tell its size, it is already known.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is unclear in what situations driver_data should be used thus better do
not upstream it for now. If a need arises in the future a discussion can
be started to re-add it.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

info_data is a bit redundant, let's keep it as only sync_file_info. It is
also smaller.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As struct sync_pt doesn't exist anymore it is a good idea remove any
reference to it in the sync_framework. sync_pts were replaced directly by
fences and here we rename it to sync_fence_info to let the fence namespace
clean.

v2: rename fence_info to sync_fence_info (Maarten)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This ioctl is replicating the work of poll() syscall so let's take the
opportunity that this is still on staging tree and remove the duplication
and force new users to use the poll() standard interface.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a patch to ion_page_pool.c that changes a memory allocation
style issue as found by checkpatch.pl.
Signed-off-by: Ben Marsh <bmarsh94@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the removal of struct sync_pt sync_fence_create_dma() now takes
the same arguments as sync_fence_create() so let's keep only
sync_fence_create().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All changes to timeline value come through the user via
sync_timeline_signal() calls. When sync_timeline_destroy() is called no
changes on timeline->value happens hence call sync_timeline_signal() with
no increment is pointless.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

signaled_pts is not used in this function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

struct sync_pt was just wrapping around struct fence and creating an
extra abstraction layer. The only two members of struct sync_pt, child_list
and active_list, were moved to struct fence in an earlier commit. After
removing those two members struct sync_pt is nothing more than struct
fence, so remove it all and use struct fence directly.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

'sync_pt' is actually declared as struct fence so to make the name means
its type we rename it to 'fence'.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sync_file has a more close meaning to what a sync_fence really, a struct
that represent a file that can be used by userspace to get information on
a fence, or wait for it to be signaled.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This remove CONFIG_SW_SYNC_USER and instead compile the sw_sync file into
debugpfs under <debugfs>/sync/sw_sync.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Creates the 'sync' dir on debugfs root dir and move the 'sync' file
to sync/info. This is the preparation to add more debug info and control.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

.dup and .compare are not used by the sync framework, so remove them
from sw_sync.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These interfaces are not used nor have plans to be used in the near
future so remove them for a cleaner solution before de-staging the sync
framework.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Updates comments about functions and structures.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sanity check at binder ioctl function,
Only allow the shared mm_struct to use the same binder-object
to do binder operate.

And add proc->vma_vm_mm = current->mm at the open function.
The libbinder do ioctl before mmap called.

V2: Fix compile error for error commit
V3: Change the condition to proc->vma_vm_mm
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Wei  Dong <weidong2@hisilicon.com>
Signed-off-by: Junmin Zhao <zhaojunmin@huawei.com>
Reviewed-by: Zhuangluan Su <suzhuangluan@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ion_buffer_create() will allocate a buffer and then create a DMA
mapping for it, but it forgot to set the length of the page entries.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since ion alloc can be called by userspace,eg gralloc.
When it is called frequently, the efficiency of kswapd is
to low. And the reclaimed memory is too lower. In this way,
the kswapd can use to much cpu resources.

With 3.5GB DMA Zone and 0.5 Normal Zone.

pgsteal_kswapd_dma 9364140
pgsteal_kswapd_normal 7071043
pgscan_kswapd_dma 10428250
pgscan_kswapd_normal 37840094

With this change the reclaim ratio has greatly improved
18.9% -> 72.5%
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Lu bing <albert.lubing@hisilicon.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a patch to the sync_debug.c file that rectifies a brace warning
that was found with the checkpatch.pl tool
Signed-off-by: Bopamo Osaisai <bopamo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In carveout heap, change minimum allocation order from 12 to
PAGE_SHIFT. After this change each bit in bitmap (genalloc -
General purpose special memory pool) represents one page size
memory.

Cc: sprd-ind-kernel-group@googlegroups.com
Cc: sanjeev.yadav@spreadtrum.com
Cc: Colin Cross <ccross@android.com>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Rajmal Menariya <rajmal.menariya@spreadtrum.com>
[jstultz: Reworked commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lowmemorykiller debug messages are inscrutable and mostly useful
for debugging the lowmemorykiller, not explaining why a process
was killed.  Make the messages more useful by prefixing them
with "lowmemorykiller: " and explaining in more readable terms
what was killed, who it was killed for, and why it was killed.

The messages now look like:
[   76.997631] lowmemorykiller: Killing 'droid.gallery3d' (2172), adj 1000,
[   76.997635]    to free 27436kB on behalf of 'kswapd0' (29) because
[   76.997638]    cache 122624kB is below limit 122880kB for oom_score_adj 1000
[   76.997641]    Free memory is -53356kB above reserved

A negative number for free memory above reserved means some of the
reserved memory has been used and is being regenerated by kswapd,
which is likely what called the shrinkers.

Cc: Android Kernel Team <kernel-team@android.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Colin Cross <ccross@android.com>
[jstultz: Minor checkpatch tweaks]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Include <linux/types.h> into ashmem.h to ensure referenced types
are defined

Cc: Android Kernel Team <kernel-team@android.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Rom Lemarchand <romlem@android.com>
[jstultz: Minor commit message tweaks]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Both ashmem_mmap and ashmem_shrink take the ashmem_lock. It may
be possible for ashmem_mmap to invoke ashmem_shrink:

-000|mutex_lock(lock = 0x0)
-001|ashmem_shrink(?, sc = 0x0) <--- try to take ashmem_mutex again
-002|shrink_slab(shrink = 0xDA5F1CC0, nr_pages_scanned = 0, lru_pages
-002|=
-002|124)
-003|try_to_free_pages(zonelist = 0x0, ?, ?, ?)
-004|__alloc_pages_nodemask(gfp_mask = 21200, order = 1, zonelist =
-004|0xC11D0940,
-005|new_slab(s = 0xE4841E80, ?, node = -1)
-006|__slab_alloc.isra.43.constprop.50(s = 0xE4841E80, gfpflags =
-006|2148925462, ad
-007|kmem_cache_alloc(s = 0xE4841E80, gfpflags = 208)
-008|shmem_alloc_inode(?)
-009|alloc_inode(sb = 0xE480E800)
-010|new_inode_pseudo(?)
-011|new_inode(?)
-012|shmem_get_inode(sb = 0xE480E800, dir = 0x0, ?, dev = 0, flags =
-012|187)
-013|shmem_file_setup(?, ?, flags = 187)
-014|ashmem_mmap(?, vma = 0xC5D64210) <---- Acquire ashmem_mutex
-015|mmap_region(file = 0xDF8E2C00, addr = 1772974080, len = 233472,
-015|flags = 57,
-016|sys_mmap_pgoff(addr = 0, len = 230400, prot = 3, flags = 1, fd =
-016|157, pgoff
-017|ret_fast_syscall(asm)
-->|exception
-018|NUR:0x40097508(asm)
---|end of frame

Avoid this deadlock by using mutex_trylock in ashmem_shrink; if the mutex
is already held, do not attempt to shrink.

Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Android Kernel Team <kernel-team@android.com>
Reported-by: Matt Wagantall <mattw@codeaurora.org>
Reported-by: Syed Rameez Mustafa <rameezmustafa@codeaurora.org>
Reported-by: Osvaldo Banuelos <osvaldob@codeaurora.org>
Reported-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
[jstultz: Minor commit message tweaks]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This removes a few Sparse warnings.
Signed-off-by: Hugo Camboulive <hugo.camboulive@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace multiple if..else if..statements with simple table lookup in two
functions.
Signed-off-by: Hari Prasath Gujulan Elango <hgujulan@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

device_create() returns ERR_PTR on error, it does not return NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes the second forwared declaration of struct most_aim.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a counter for dropped packets. It needed for statistical
analysis.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>