- 03 Jun, 2016 40 commits
-
-
Catalin Marinas authored
[ Upstream commit 5bb1cc0f ] Currently, pmd_present() only checks for a non-zero value, returning true even after pmd_mknotpresent() (which only clears the type bits). This patch converts pmd_present() to using pte_present(), similar to the other pmd_*() checks. As a side effect, it will return true for PROT_NONE mappings, though they are not yet used by the kernel with transparent huge pages. For consistency, also change pmd_mknotpresent() to only clear the PMD_SECT_VALID bit, even though the PMD_TABLE_BIT is already 0 for block mappings (no functional change). The unused PMD_SECT_PROT_NONE definition is removed as transparent huge pages use the pte page prot values. Fixes: 9c7e535f ("arm64: mm: Route pmd thp functions through pte equivalents") Cc: <stable@vger.kernel.org> # 3.15+ Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Nicolai Stange authored
[ Upstream commit 935244cd ] Currently, in ext4_mb_init(), there's a loop like the following: do { ... offset += 1 << (sb->s_blocksize_bits - i); i++; } while (i <= sb->s_blocksize_bits + 1); Note that the updated offset is used in the loop's next iteration only. However, at the last iteration, that is at i == sb->s_blocksize_bits + 1, the shift count becomes equal to (unsigned)-1 > 31 (c.f. C99 6.5.7(3)) and UBSAN reports UBSAN: Undefined behaviour in fs/ext4/mballoc.c:2621:15 shift exponent 4294967295 is too large for 32-bit type 'int' [...] Call Trace: [<ffffffff818c4d25>] dump_stack+0xbc/0x117 [<ffffffff818c4c69>] ? _atomic_dec_and_lock+0x169/0x169 [<ffffffff819411ab>] ubsan_epilogue+0xd/0x4e [<ffffffff81941cac>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254 [<ffffffff81941ab1>] ? __ubsan_handle_load_invalid_value+0x158/0x158 [<ffffffff814b6dc1>] ? kmem_cache_alloc+0x101/0x390 [<ffffffff816fc13b>] ? ext4_mb_init+0x13b/0xfd0 [<ffffffff814293c7>] ? create_cache+0x57/0x1f0 [<ffffffff8142948a>] ? create_cache+0x11a/0x1f0 [<ffffffff821c2168>] ? mutex_lock+0x38/0x60 [<ffffffff821c23ab>] ? mutex_unlock+0x1b/0x50 [<ffffffff814c26ab>] ? put_online_mems+0x5b/0xc0 [<ffffffff81429677>] ? kmem_cache_create+0x117/0x2c0 [<ffffffff816fcc49>] ext4_mb_init+0xc49/0xfd0 [...] Observe that the mentioned shift exponent, 4294967295, equals (unsigned)-1. Unless compilers start to do some fancy transformations (which at least GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the such calculated value of offset is never used again. Silence UBSAN by introducing another variable, offset_incr, holding the next increment to apply to offset and adjust that one by right shifting it by one position per loop iteration. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161 Cc: stable@vger.kernel.org Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Nicolai Stange authored
[ Upstream commit b5cb316c ] Currently, in mb_find_order_for_block(), there's a loop like the following: while (order <= e4b->bd_blkbits + 1) { ... bb += 1 << (e4b->bd_blkbits - order); } Note that the updated bb is used in the loop's next iteration only. However, at the last iteration, that is at order == e4b->bd_blkbits + 1, the shift count becomes negative (c.f. C99 6.5.7(3)) and UBSAN reports UBSAN: Undefined behaviour in fs/ext4/mballoc.c:1281:11 shift exponent -1 is negative [...] Call Trace: [<ffffffff818c4d35>] dump_stack+0xbc/0x117 [<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169 [<ffffffff819411bb>] ubsan_epilogue+0xd/0x4e [<ffffffff81941cbc>] __ubsan_handle_shift_out_of_bounds+0x1fb/0x254 [<ffffffff81941ac1>] ? __ubsan_handle_load_invalid_value+0x158/0x158 [<ffffffff816e93a0>] ? ext4_mb_generate_from_pa+0x590/0x590 [<ffffffff816502c8>] ? ext4_read_block_bitmap_nowait+0x598/0xe80 [<ffffffff816e7b7e>] mb_find_order_for_block+0x1ce/0x240 [...] Unless compilers start to do some fancy transformations (which at least GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the such calculated value of bb is never used again. Silence UBSAN by introducing another variable, bb_incr, holding the next increment to apply to bb and adjust that one by right shifting it by one position per loop iteration. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=114701 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112161 Cc: stable@vger.kernel.org Signed-off-by: Nicolai Stange <nicstange@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Jan Kara authored
[ Upstream commit 74177f55 ] When filesystem is corrupted in the right way, it can happen ext4_mark_iloc_dirty() in ext4_orphan_add() returns error and we subsequently remove inode from the in-memory orphan list. However this deletion is done with list_del(&EXT4_I(inode)->i_orphan) and thus we leave i_orphan list_head with a stale content. Later we can look at this content causing list corruption, oops, or other issues. The reported trace looked like: WARNING: CPU: 0 PID: 46 at lib/list_debug.c:53 __list_del_entry+0x6b/0x100() list_del corruption, 0000000061c1d6e0->next is LIST_POISON1 0000000000100100) CPU: 0 PID: 46 Comm: ext4.exe Not tainted 4.1.0-rc4+ #250 Stack: 60462947 62219960 602ede24 62219960 602ede24 603ca293 622198f0 602f02eb 62219950 6002c12c 62219900 601b4d6b Call Trace: [<6005769c>] ? vprintk_emit+0x2dc/0x5c0 [<602ede24>] ? printk+0x0/0x94 [<600190bc>] show_stack+0xdc/0x1a0 [<602ede24>] ? printk+0x0/0x94 [<602ede24>] ? printk+0x0/0x94 [<602f02eb>] dump_stack+0x2a/0x2c [<6002c12c>] warn_slowpath_common+0x9c/0xf0 [<601b4d6b>] ? __list_del_entry+0x6b/0x100 [<6002c254>] warn_slowpath_fmt+0x94/0xa0 [<602f4d09>] ? __mutex_lock_slowpath+0x239/0x3a0 [<6002c1c0>] ? warn_slowpath_fmt+0x0/0xa0 [<60023ebf>] ? set_signals+0x3f/0x50 [<600a205a>] ? kmem_cache_free+0x10a/0x180 [<602f4e88>] ? mutex_lock+0x18/0x30 [<601b4d6b>] __list_del_entry+0x6b/0x100 [<601177ec>] ext4_orphan_del+0x22c/0x2f0 [<6012f27c>] ? __ext4_journal_start_sb+0x2c/0xa0 [<6010b973>] ? ext4_truncate+0x383/0x390 [<6010bc8b>] ext4_write_begin+0x30b/0x4b0 [<6001bb50>] ? copy_from_user+0x0/0xb0 [<601aa840>] ? iov_iter_fault_in_readable+0xa0/0xc0 [<60072c4f>] generic_perform_write+0xaf/0x1e0 [<600c4166>] ? file_update_time+0x46/0x110 [<60072f0f>] __generic_file_write_iter+0x18f/0x1b0 [<6010030f>] ext4_file_write_iter+0x15f/0x470 [<60094e10>] ? unlink_file_vma+0x0/0x70 [<6009b180>] ? unlink_anon_vmas+0x0/0x260 [<6008f169>] ? free_pgtables+0xb9/0x100 [<600a6030>] __vfs_write+0xb0/0x130 [<600a61d5>] vfs_write+0xa5/0x170 [<600a63d6>] SyS_write+0x56/0xe0 [<6029fcb0>] ? __libc_waitpid+0x0/0xa0 [<6001b698>] handle_syscall+0x68/0x90 [<6002633d>] userspace+0x4fd/0x600 [<6002274f>] ? save_registers+0x1f/0x40 [<60028bd7>] ? arch_prctl+0x177/0x1b0 [<60017bd5>] fork_handler+0x85/0x90 Fix the problem by using list_del_init() as we always should with i_orphan list. CC: stable@vger.kernel.org Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Konstantin Shkolnyy authored
[ Upstream commit a377f9e9 ] A bug in the CRTSCTS handling caused RTS to alternate between CRTSCTS=0 => "RTS is transmit active signal" and CRTSCTS=1 => "RTS is used for receive flow control" instead of CRTSCTS=0 => "RTS is statically active" and CRTSCTS=1 => "RTS is used for receive flow control" This only happened after first having enabled CRTSCTS. Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Fixes: 39a66b8d ("[PATCH] USB: CP2101 Add support for flow control") Cc: stable <stable@vger.kernel.org> [johan: reword commit message ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Konstantin Shkolnyy authored
[ Upstream commit e2ae67a3 ] This change is preparation for implementing a cp2108 bug workaround. The workaround requires storing some private data. Right now the data is attached to the USB interface and allocated in the attach() callback. The bug detection requires USB I/O which is done easier from port_probe() callback rather than attach(). Since the USB access functions take port as a parameter, and since the private data is used exclusively by these functions, it can be allocated in port_probe(). Also, all cp210x devices have exactly 1 port per USB iterface, so moving private data from the USB interface to port is trivial. Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Lv Zheng authored
[ Upstream commit 30c9bb0d ] The order of the _OSI related functionalities is as follows: acpi_blacklisted() acpi_dmi_osi_linux() acpi_osi_setup() acpi_osi_setup() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< parse_args() __setup("acpi_osi=") acpi_osi_setup_linux() acpi_update_interfaces() if "!*" <<<<<<<<<<<<<<<<<<<<<<<< acpi_early_init() acpi_initialize_subsystem() acpi_ut_initialize_interfaces() ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ acpi_bus_init() acpi_os_initialize1() acpi_install_interface_handler(acpi_osi_handler) acpi_osi_setup_late() acpi_update_interfaces() for "!" >>>>>>>>>>>>>>>>>>>>>>>> acpi_osi_handler() Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command line setting can override the DMI detection. That's why acpi_blacklisted() is put before __setup("acpi_osi="). Then we can notice the following wrong invocation order. There are acpi_update_interfaces() (marked by <<<<) calls invoked before acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible to use acpi_osi=!* correctly from OSI DMI table or from the command line. The use of acpi_osi=!* is meant to disable both ACPICA (acpi_gbl_supported_interfaces) and Linux specific strings (osi_setup_entries) while the ACPICA part should have stopped working because of the order issue. This patch fixes this issue by moving acpi_update_interfaces() to where it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux specific strings are still handled in the original place in order to make the following command line working: acpi_osi=!* acpi_osi="Module Device". Note that since acpi_osi=!* is meant to further disable linux specific string comparing to the acpi_osi=!, there is no such use case in our bug fixing work and hence there is no one using acpi_osi=!* either from the command line or from the DMI quirks, this issue is just a theoretical issue. Fixes: 741d8128 (ACPI: Add facility to remove all _OSI strings) Cc: 3.12+ <stable@vger.kernel.org> # 3.12+ Tested-by: Lukas Wunner <lukas@wunner.de> Tested-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Lei Liu authored
[ Upstream commit 74d2a91a ] Add even more ZTE device ids. Signed-off-by: lei liu <liu.lei78@zte.com.cn> Cc: stable <stable@vger.kernel.org> [johan: rebase and replace commit message ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
lei liu authored
[ Upstream commit f0d09463 ] More ZTE device ids. Signed-off-by: lei liu <liu.lei78@zte.com.cn> Cc: stable <stable@vger.kernel.org> [properly sort them - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Andreas Werner authored
[ Upstream commit f75564d3 ] The bar number is found in reg2 within the gdd. Therefore we need to change the assigment from reg1 to reg2 which is the correct location. Signed-off-by: Andreas Werner <andreas.werner@men.de> Fixes: '3764e82e' drivers: Introduce MEN Chameleon Bus Cc: stable@vger.kernel.org # v3.15+ Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Mathias Nyman authored
[ Upstream commit cdc77c82 ] The current implemenentation restart the sent pattern for each entry in the sg list. The receiving end expects a continuous pattern, and test will fail unless scatterilst entries happen to be aligned with the pattern Fix this by calculating the pattern byte based on total sent size instead of just the current sg entry. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Fixes: 8b524901 ("[PATCH] USB: usbtest: scatterlist OUT data pattern testing") Cc: <stable@vger.kernel.org> # v2.6.18+ Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Alan Stern authored
[ Upstream commit b9a6e8e1 ] With this change, the host and gadget doesn't need to agree with transfer length for comparing the data, since they doesn't know each other's transfer size, but know max packet size. Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> (Fixed the 'line over 80 characters warning' by Peter Chen) Tested-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Alan Stern authored
[ Upstream commit 6fb650d4 ] When a USB driver is bound to an interface (either through probing or by claiming it) or is unbound from an interface, the USB core always disables Link Power Management during the transition and then re-enables it afterward. The reason is because the driver might want to prevent hub-initiated link power transitions, in which case the HCD would have to recalculate the various LPM parameters. This recalculation takes place when LPM is re-enabled and the new parameters are sent to the device and its parent hub. However, if the driver does not want to prevent hub-initiated link power transitions then none of this work is necessary. The parameters don't need to be recalculated, and LPM doesn't need to be disabled and re-enabled. It turns out that disabling and enabling LPM can be time-consuming, enough so that it interferes with user programs that want to claim and release interfaces rapidly via usbfs. Since the usbfs kernel driver doesn't set the disable_hub_initiated_lpm flag, we can speed things up and get the user programs to work by leaving LPM alone whenever the flag isn't set. And while we're improving the way disable_hub_initiated_lpm gets used, let's also fix its kerneldoc. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Matthew Giassa <matthew@giassa.net> CC: Mathias Nyman <mathias.nyman@intel.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Schemmel Hans-Christoph authored
[ Upstream commit 444f94e9 ] Added support for Gemalto's Cinterion PH8 and AHxx products with 2 RmNet Interfaces and products with 1 RmNet + 1 USB Audio interface. In addition some minor renaming and formatting. Signed-off-by: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com> [johan: sort current entries and trim trailing whitespace ] Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Andreas Noever authored
[ Upstream commit 2ffa9a5d ] If tb_drom_read() fails, sw->drom is freed but not set to NULL. sw->drom is then freed again in the error path of tb_switch_alloc(). The bug can be triggered by unplugging a thunderbolt device shortly after it is detected by the thunderbolt driver. Clear sw->drom if tb_drom_read() fails. [bhelgaas: add Fixes:, stable versions of interest] Fixes: 343fcb8c ("thunderbolt: Fix nontrivial endpoint devices.") Signed-off-by: Andreas Noever <andreas.noever@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.17+ CC: Lukas Wunner <lukas@wunner.de> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Zhao Qiang authored
[ Upstream commit 11ca2b7a ] New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart. So add it. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Brian Bloniarz authored
[ Upstream commit 0f40fbbc ] OpenSSH expects the (non-blocking) read() of pty master to return EAGAIN only if it has received all of the slave-side output after it has received SIGCHLD. This used to work on pre-3.12 kernels. This fix effectively forces non-blocking read() and poll() to block for parallel i/o to complete for all ttys. It also unwinds these changes: 1) f8747d4a tty: Fix pty master read() after slave closes 2) 52bce7f8 pty, n_tty: Simplify input processing on final close 3) 1a48632f pty: Fix input race when closing Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net> Reported-by: Volth <openssh@volth.com> Reported-by: Marc Aurele La France <tsi@tuyoix.net> BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52 BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Matthias Schiffer authored
[ Upstream commit f5b556c9 ] This makes the ath79 bootconsole behave the same way as the generic 8250 bootconsole. Also waiting for TEMT (transmit buffer is empty) instead of just THRE (transmit buffer is not full) ensures that all characters have been transmitted before the real serial driver starts reconfiguring the serial controller (which would sometimes result in garbage being transmitted.) This change does not cause a visible performance loss. In addition, this seems to fix a hang observed in certain configurations on many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver. A more complete follow-up patch will disable 8250 autoconfig for ath79 altogether (the serial controller is detected as a 16550A, which is not fully compatible with the ath79 serial, and the autoconfig may lead to undefined behavior on ath79.) Cc: <stable@vger.kernel.org> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Theodore Ts'o authored
[ Upstream commit 7827a7f6 ] Instead of just printing warning messages, if the orphan list is corrupted, declare the file system is corrupted. If there are any reserved inodes in the orphaned inode list, declare the file system corrupted and stop right away to avoid doing more potential damage to the file system. Cc: stable@vger.kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Theodore Ts'o authored
[ Upstream commit c9eb13a9 ] If the orphaned inode list contains inode #5, ext4_iget() returns a bad inode (since the bootloader inode should never be referenced directly). Because of the bad inode, we end up processing the inode repeatedly and this hangs the machine. This can be reproduced via: mke2fs -t ext4 /tmp/foo.img 100 debugfs -w -R "ssv last_orphan 5" /tmp/foo.img mount -o loop /tmp/foo.img /mnt (But don't do this if you are using an unpatched kernel if you care about the system staying functional. :-) This bug was found by the port of American Fuzzy Lop into the kernel to find file system problems[1]. (Since it *only* happens if inode #5 shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not surprising that AFL needed two hours before it found it.) [1] http://events.linuxfoundation.org/sites/events/files/slides/AFL%20filesystem%20fuzzing%2C%20Vault%202016_0.pdf Cc: stable@vger.kernel.org Reported by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Raghava Aditya Renukunta authored
[ Upstream commit 78cbccd3 ] When KDUMP is triggered the driver first talks to the firmware in INTX mode, but the adapter firmware is still in MSIX mode. Therefore the first driver command hangs since the driver is waiting for an INTX response and firmware gives a MSIX response. If when the OS is installed on a RAID drive created by the adapter KDUMP will hang since the driver does not receive a response in sync mode. Fixed by: Change the firmware to INTX mode if it is in MSIX mode before sending the first sync command. Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Raghava Aditya Renukunta authored
[ Upstream commit fc4bf75e ] Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Raghava Aditya Renukunta authored
[ Upstream commit 07beca2b ] aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Cc: stable@vger.kernel.org Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Marc Zyngier authored
[ Upstream commit d4b9e079 ] The ARM architecture mandates that when changing a page table entry from a valid entry to another valid entry, an invalid entry is first written, TLB invalidated, and only then the new entry being written. The current code doesn't respect this, directly writing the new entry and only then invalidating TLBs. Let's fix it up. Cc: <stable@vger.kernel.org> Reported-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
H Hartley Sweeten authored
[ Upstream commit d375278d ] DMA is optional with this driver. If it was not enabled the devpriv->dma pointer will be NULL. Fix the possible NULL pointer dereference when trying to disable the DMA channels in das1800_ai_cancel() and tidy up the comments to fix the checkpatch.pl issues: WARNING: line over 80 characters It's probably harmless in das1800_ai_setup_dma() because the 'desc' pointer will not be used if DMA is disabled but fix it there also. Fixes: 99dfc335 ("staging: comedi: das1800: remove depends on ISA_DMA_API limitation") Cc: <stable@vger.kernel.org> # 4.0+ Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Jiri Slaby authored
[ Upstream commit d175feca ] Dmitry reported, that the current cleanup code in n_gsm can trigger a warning: WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0() ... Call Trace: ... [<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490 [<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048 [<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386 [<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447 [<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567 [< inline >] tiocsetd drivers/tty/tty_io.c:2650 [<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883 ... But this is a legal path when open fails to find a space in the gsm_mux array and tries to clean up. So make it a standard test instead of a warning. Reported-by: "Dmitry Vyukov" <dvyukov@google.com> Cc: Alan Cox <alan@linux.intel.com> Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
David Müller authored
[ Upstream commit 6f210c18 ] Since commit 21947ba6 ("serial: 8250_pci: replace switch-case by formula"), the 8250 driver crashes in the byt_set_termios() function with a divide error. This is caused by the fact that a baud rate of 0 (B0) is not handled properly. Fix it by falling back to B9600 in this case. Signed-off-by: David Müller <d.mueller@elsoft.ch> Fixes: 21947ba6 ("serial: 8250_pci: replace switch-case by formula") Cc: stable@vger.kernel.org Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Chris Bainbridge authored
[ Upstream commit feb26ac3 ] The XHCI controller presents two USB buses to the system - one for USB2 and one for USB3. The hub init code (hub_port_init) is reentrant but only locks one bus per thread, leading to a race condition failure when two threads attempt to simultaneously initialise a USB2 and USB3 device: [ 8.034843] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command [ 13.183701] usb 3-3: device descriptor read/all, error -110 On a test system this failure occurred on 6% of all boots. The call traces at the point of failure are: Call Trace: [<ffffffff81b9bab7>] schedule+0x37/0x90 [<ffffffff817da7cd>] usb_kill_urb+0x8d/0xd0 [<ffffffff8111e5e0>] ? wake_up_atomic_t+0x30/0x30 [<ffffffff817dafbe>] usb_start_wait_urb+0xbe/0x150 [<ffffffff817db10c>] usb_control_msg+0xbc/0xf0 [<ffffffff817d07de>] hub_port_init+0x51e/0xb70 [<ffffffff817d4697>] hub_event+0x817/0x1570 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620 [<ffffffff810f4684>] worker_thread+0x64/0x4b0 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390 [<ffffffff810fa7f5>] kthread+0x105/0x120 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 Call Trace: [<ffffffff817fd36d>] xhci_setup_device+0x53d/0xa40 [<ffffffff817fd87e>] xhci_address_device+0xe/0x10 [<ffffffff817d047f>] hub_port_init+0x1bf/0xb70 [<ffffffff811247ed>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff817d4697>] hub_event+0x817/0x1570 [<ffffffff810f3e6f>] process_one_work+0x1ff/0x620 [<ffffffff810f3dcf>] ? process_one_work+0x15f/0x620 [<ffffffff810f4684>] worker_thread+0x64/0x4b0 [<ffffffff810f4620>] ? rescuer_thread+0x390/0x390 [<ffffffff810fa7f5>] kthread+0x105/0x120 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 [<ffffffff81ba183f>] ret_from_fork+0x3f/0x70 [<ffffffff810fa6f0>] ? kthread_create_on_node+0x200/0x200 Which results from the two call chains: hub_port_init usb_get_device_descriptor usb_get_descriptor usb_control_msg usb_internal_control_msg usb_start_wait_urb usb_submit_urb / wait_for_completion_timeout / usb_kill_urb hub_port_init hub_set_address xhci_address_device xhci_setup_device Mathias Nyman explains the current behaviour violates the XHCI spec: hub_port_reset() will end up moving the corresponding xhci device slot to default state. As hub_port_reset() is called several times in hub_port_init() it sounds reasonable that we could end up with two threads having their xhci device slots in default state at the same time, which according to xhci 4.5.3 specs still is a big no no: "Note: Software shall not transition more than one Device Slot to the Default State at a time" So both threads fail at their next task after this. One fails to read the descriptor, and the other fails addressing the device. Fix this in hub_port_init by locking the USB controller (instead of an individual bus) to prevent simultaneous initialisation of both buses. Fixes: 638139eb ("usb: hub: allow to process more usb hub events in parallel") Link: https://lkml.org/lkml/2016/2/8/312 Link: https://lkml.org/lkml/2016/2/4/748Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Luke Dashjr authored
[ Upstream commit 4c63c245 ] 32-bit ioctl uses these rather than the regular FS_IOC_* versions. They can be handled in btrfs using the same code. Without this, 32-bit {ch,ls}attr fail. Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org> Cc: stable@vger.kernel.org Reviewed-by: Josef Bacik <jbacik@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Andrew Jeffery authored
[ Upstream commit 71324fdc ] The range is registered into a linked list which can be referenced throughout the lifetime of the driver. Ensure the range's memory is useful for the same lifetime by adding it to the driver's private data structure. The bug was introduced in the driver's initial commit, which was present in v3.10. Fixes: f0b9a7e5 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC") Cc: stable@vger.kernel.org Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Vittorio Gambaletta (VittGam) authored
[ Upstream commit 0f9edcdd ] The Wistron DNMA-92 and Compex WLM200NX have inverted LED polarity (active high instead of active low). The same PCI Subsystem ID is used by both cards, which are based on the same Atheros MB92 design. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Cc: <stable@vger.kernel.org> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Vittorio Gambaletta (VittGam) authored
[ Upstream commit cd84042c ] The LED can be active high instead of active low on some hardware. Add the led_active_high module parameter. It defaults to -1 to obey platform data as before. Setting the parameter to 1 or 0 will force the LED respectively active high or active low. Cc: <linux-wireless@vger.kernel.org> Cc: <ath9k-devel@qca.qualcomm.com> Cc: <ath9k-devel@lists.ath9k.org> Cc: <stable@vger.kernel.org> Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Krzysztof Kozlowski authored
[ Upstream commit 79152e8d ] The tcrypt testing module on Exynos5422-based Odroid XU3/4 board failed on testing 8 kB size blocks: $ sudo modprobe tcrypt sec=1 mode=500 testing speed of async ecb(aes) (ecb-aes-s5p) encryption test 0 (128 bit key, 16 byte blocks): 21971 operations in 1 seconds (351536 bytes) test 1 (128 bit key, 64 byte blocks): 21731 operations in 1 seconds (1390784 bytes) test 2 (128 bit key, 256 byte blocks): 21932 operations in 1 seconds (5614592 bytes) test 3 (128 bit key, 1024 byte blocks): 21685 operations in 1 seconds (22205440 bytes) test 4 (128 bit key, 8192 byte blocks): This was caused by a race issue of missed BRDMA_DONE ("Block cipher Receiving DMA") interrupt. Device starts processing the data in DMA mode immediately after setting length of DMA block: receiving (FCBRDMAL) or transmitting (FCBTDMAL). The driver sets these lengths from interrupt handler through s5p_set_dma_indata() function (or xxx_setdata()). However the interrupt handler was first dealing with receive buffer (dma-unmap old, dma-map new, set receive block length which starts the operation), then with transmit buffer and finally was clearing pending interrupts (FCINTPEND). Because of the time window between setting receive buffer length and clearing pending interrupts, the operation on receive buffer could end already and driver would miss new interrupt. User manual for Exynos5422 confirms in example code that setting DMA block lengths should be the last operation. The tcrypt hang could be also observed in following blocked-task dmesg: INFO: task modprobe:258 blocked for more than 120 seconds. Not tainted 4.6.0-rc4-next-20160419-00005-g9eac8b7b7753-dirty #42 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. modprobe D c06b09d8 0 258 256 0x00000000 [<c06b09d8>] (__schedule) from [<c06b0f24>] (schedule+0x40/0xac) [<c06b0f24>] (schedule) from [<c06b49f8>] (schedule_timeout+0x124/0x178) [<c06b49f8>] (schedule_timeout) from [<c06b17fc>] (wait_for_common+0xb8/0x144) [<c06b17fc>] (wait_for_common) from [<bf0013b8>] (test_acipher_speed+0x49c/0x740 [tcrypt]) [<bf0013b8>] (test_acipher_speed [tcrypt]) from [<bf003e8c>] (do_test+0x2240/0x30ec [tcrypt]) [<bf003e8c>] (do_test [tcrypt]) from [<bf008048>] (tcrypt_mod_init+0x48/0xa4 [tcrypt]) [<bf008048>] (tcrypt_mod_init [tcrypt]) from [<c010177c>] (do_one_initcall+0x3c/0x16c) [<c010177c>] (do_one_initcall) from [<c0191ff0>] (do_init_module+0x5c/0x1ac) [<c0191ff0>] (do_init_module) from [<c0185610>] (load_module+0x1a30/0x1d08) [<c0185610>] (load_module) from [<c0185ab0>] (SyS_finit_module+0x8c/0x98) [<c0185ab0>] (SyS_finit_module) from [<c01078c0>] (ret_fast_syscall+0x0/0x3c) Fixes: a49e490c ("crypto: s5p-sss - add S5PV210 advanced crypto engine support") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Krzysztof Kozlowski authored
[ Upstream commit 55124425 ] Beside regular feed control interrupt, the driver requires also hash interrupt for older SoCs (samsung,s5pv210-secss). However after requesting it, the interrupt handler isn't doing anything with it, not even clearing the hash interrupt bit. Driver does not provide hash functions so it is safe to remove the hash interrupt related code and to not require the interrupt in Device Tree. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Ulf Hansson authored
[ Upstream commit 0ae3aeef ] As pm_runtime_set_active() may fail because the device's parent isn't active, we can end up executing the ->runtime_resume() callback for the device when it isn't allowed. Fix this by invoking pm_runtime_set_active() before running the callback and let's also deal with the error code. Fixes: 37f20416 (PM: Add pm_runtime_suspend|resume_force functions) Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: 3.15+ <stable@vger.kernel.org> # 3.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Hari Bathini authored
[ Upstream commit 8ed8ab40 ] Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Cc: stable@vger.kernel.org Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Takashi Iwai authored
[ Upstream commit c7c999cb ] hci_vhci driver creates a hci device object dynamically upon each HCI_VENDOR_PKT write. Although it checks the already created object and returns an error, it's still racy and may build multiple hci_dev objects concurrently when parallel writes are performed, as the device tracks only a single hci_dev object. This patch introduces a mutex to protect against the concurrent device creations. Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Akshay Bhat authored
[ Upstream commit 7a18afe8 ] On ads7828 the internal reference defaults to off upon power up. When using internal reference, it needs to be turned on and the voltage needs to settle before normal conversion cycle can be started. Hence perform a dummy read in the probe to enable the internal reference allowing the voltage to settle before performing a normal read. Without this fix, the first read from the ADC when using internal reference always returns incorrect data. Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Cc: stable@vger.kernel.org # v4.1+ Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Michal Nazarewicz authored
[ Upstream commit f78bbcae ] When binding the function to usb_configuration, check whether the thread is running before starting another one. Without that, when function instance is added to multiple configurations, fsg_bing starts multiple threads with all but the latest one being forgotten by the driver. This leads to obvious thread leaks, possible lockups when trying to halt the machine and possible more issues. This fixes issues with legacy/multi¹ gadget as well as configfs gadgets when mass_storage function is added to multiple configurations. This change also simplifies API since the legacy gadgets no longer need to worry about starting the thread by themselves (which was where bug in legacy/multi was in the first place). N.B., this patch doesn’t address adding single mass_storage function instance to a single configuration twice. Thankfully, there’s no legitimate reason for such setup plus, if I’m not mistaken, configfs gadget doesn’t even allow it to be expressed. ¹ I have no example failure though. Conclusion that legacy/multi has a bug is based purely on me reading the code. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: <stable@vger.kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-
Krzysztof Opasiak authored
[ Upstream commit dd02ea5a ] This patch replace dynamicly allocated luns array with static one. This simplifies the code of mass storage function and modules. Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
-