- 10 Aug, 2021 1 commit
-
-
Rob Clark authored
Combine adreno_is_a640() and adreno_is_a680(). Signed-off-by:
Rob Clark <robdclark@chromium.org> Link: https://lore.kernel.org/r/20210807163019.379003-1-robdclark@gmail.comSigned-off-by:
-
- 07 Aug, 2021 37 commits
-
-
Dmitry Baryshkov authored
Restore the assgined-clocks and assigned-clock-parents properties that were lost during the txt -> YAML conversion. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210709210729.953114-2-dmitry.baryshkov@linaro.orgSigned-off-by:
-
Dmitry Baryshkov authored
dpu_hw_ctl_clear_all_blendstages() clears settings for the few first LMs instead of mixers actually used for the CTL. Change it to clear necessary data, using provided mixer ids. Fixes: 25fdd593 ("drm/msm: Add SDM845 DPU support") Signed-off-by:
-
Dmitry Baryshkov authored
Add support for alpha blending properties. Setup the plane blend state according to those properties. Signed-off-by:
-
Kuogee Hsieh authored
Currently at dp_pm_resume() is_connected state is decided base on hpd connection status only. This will put is_connected in wrongly "true" state at the scenario that dongle attached to DUT but without hmdi cable connecting to it. Fix this problem by adding read sink count from dongle and decided is_connected state base on both sink count and hpd connection status. Changes in v2: -- remove dp_get_sink_count() cand call drm_dp_read_sink_count() Changes in v3: -- delete status local variable from dp_pm_resume() Changes in v4: -- delete un necessary comment at dp_pm_resume() Fixes: d9aa6571 ("drm/msm/dp: check sink_count before update is_connected status") Signed-off-by:
Kuogee Hsieh <khsieh@codeaurora.org> Link: https://lore.kernel.org/r/1628092261-32346-1-git-send-email-khsieh@codeaurora.orgTested-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
-
Kalyan Thota authored
Add safe lut configuration for all the targets in dpu driver as per QOS recommendation. Issue reported on SC7280: With wait-for-safe feature in smmu enabled, RT client buffer levels are checked to be safe before smmu invalidation. Since display was always set to unsafe it was delaying the invalidaiton process thus impacting the performance on NRT clients such as eMMC and NVMe. Validated this change on SC7280, With this change eMMC performance has improved significantly. Changes in v2: - Add fixes tag (Sai) - CC stable kernel (Dimtry) Changes in v3: - Correct fixes tag with appropriate hash (stephen) - Resend patch adding reviewed by tag - Resend patch adding correct format for pushing into stable tree (Greg) Fixes: 591e34a0 ("drm/msm/disp/dpu1: add support for display for SC7280 target") Cc: stable@vger.kernel.org Signed-off-by:
Kalyan Thota <kalyan_t@codeaurora.org> Reviewed-by:
-
Souptick Joarder authored
Kernel test roobot throws below warning -> drivers/gpu/drm/msm/dp/dp_display.c:1017:21: warning: variable 'drm' set but not used [-Wunused-but-set-variable] Removed unused variable drm. Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Souptick Joarder <jrdr.linux@gmail.com> Link: https://lore.kernel.org/r/20210709024834.29680-1-jrdr.linux@gmail.comReviewed-by:
Abhinav Kumar <abhinavk@codeaurora.org> Reviewed-by:
-
Konrad Dybcio authored
VDDA is not present and the specified load value is wrong. Fix it. Signed-off-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20210728222057.52641-1-konrad.dybcio@somainline.orgReviewed-by:
-
Guo Zhengkui authored
Remove a repeated "#include <linux/debugfs.h>" in line 19 of the original file. Signed-off-by:
Guo Zhengkui <guozhengkui@vivo.com> Link: https://lore.kernel.org/r/20210729030140.99500-1-guozhengkui@vivo.comSigned-off-by:
-
Maitreyee Rao authored
Add trace points across the MSM DP driver to help debug interop issues. Changes in v2: - Got rid of redundant log messages. - Added %#x instead of 0x%x wherever required. - Got rid of __func__ calls in debug messages. - Added newline wherever missing. Changes in v3: - Got rid of redundant log messages. - Unstuck colon from printf specifier in various places. Changes in v4: - Changed goto statement and used if else-if Changes in v5: - Changed if else if statement, to not overwrite the ret variable multiple times. Changes in v6: - Changed a wrong log message. Signed-off-by:
Maitreyee Rao <maitreye@codeaurora.org> Link: https://lore.kernel.org/r/1627346298-11528-1-git-send-email-maitreye@codeaurora.orgReviewed-by:
-
Dmitry Baryshkov authored
set_encoder_mode callback is completely unused now. Drop it from msm_kms_func(). Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Dmitry Baryshkov authored
None of the display drivers now implement set_encoder_mode callback. Stop calling it from the modeset init code. Signed-off-by:
-
Dmitry Baryshkov authored
None of the display drivers now implement set_encoder_mode callback. Stop calling it from the modeset init code. Signed-off-by:
-
Dmitry Baryshkov authored
Move a call to mdp5_encoder_set_intf_mode() after msm_dsi_modeset_init(), removing set_encoder_mode callback. Signed-off-by:
-
Dmitry Baryshkov authored
Move setting up encoders from set_encoder_mode to _dpu_kms_initialize_dsi() / _dpu_kms_initialize_displayport(). This allows us to support not only "single DSI" and "bonded DSI" but also "two independent DSI" configurations. In future this would also help adding support for multiple DP connectors. Signed-off-by:
-
Dmitry Baryshkov authored
Add three helper functions to be used by display drivers for setting up encoders. Signed-off-by:
-
Dmitry Baryshkov authored
We are preparing to support two independent DSI hosts in the DSI/DPU code. To remove possible confusion (as both configurations can be referenced as dual DSI) let's rename old "dual DSI" (two DSI hosts driving single device, with clocks being locked) to "bonded DSI". Signed-off-by:
-
Abhinav Kumar authored
During board bringups its useful to have a DSI test pattern generator to isolate a DPU vs a DSI issue and focus on the relevant hardware block. To facilitate this, add an API which triggers the DSI controller test pattern. The expected output is a rectangular checkered pattern. This has been validated on a single DSI video mode panel by calling it right after drm_panel_enable() which is also the ideal location to use this as the DSI host and the panel have been initialized by then. Further validation on dual DSI and command mode panel is pending. If there are any fix ups needed for those, it shall be applied on top of this change. Changes in v2: - generate the new dsi.xml.h and update the bitfield names Signed-off-by:
-
Abhinav Kumar authored
Update the DSI controller header XML file to add registers and bitfields to support rectangular checkered pattern generator. Signed-off-by:
-
Rajeev Nandan authored
Add support for v2.5.0 DSI block in the SC7280 SoC. Signed-off-by:
Rajeev Nandan <rajeevny@codeaurora.org> Reviewed-by:
-
Rajeev Nandan authored
The SC7280 SoC uses the 7nm (V4.1) DSI PHY driver with different enable|disable regulator loads. Signed-off-by:
-
Rajeev Nandan authored
The SC7280 SoC uses the 7nm (V4.1) DSI PHY driver. Signed-off-by:
Rob Herring <robh+dt@kernel.org> Reviewed-by:
-
Dmitry Baryshkov authored
Instead of fetching shared timing through an extra function call, get them directly from msm_dsi_phy_enable. Signed-off-by:
-
Dmitry Baryshkov authored
Use of_device_get_match-data() instead of of_match_node(). Signed-off-by:
-
Stephen Boyd authored
Add some missing newlines to the various DRM printks in this file. Noticed while looking at logs. While we're here unbreak quoted strings so grepping them is easier. Signed-off-by:
-
David Heidelberg authored
msm_atomic is doing vblank get/put's already, currently there no need to duplicate the effort in MDP4 Fix warning: ... WARNING: CPU: 3 PID: 79 at drivers/gpu/drm/drm_vblank.c:1194 drm_vblank_put+0x1cc/0x1d4 ... and multiple vblank time-outs: ... msm 5100000.mdp: vblank time out, crtc=1 ... Tested on Nexus 7 2013 (deb), LTS 5.10.50. Introduced by: 119ecb7f ("drm/msm/mdp4: request vblank during modeset") Signed-off-by:
David Heidelberg <david@ixit.cz> Link: https://lore.kernel.org/r/20210715060925.7880-1-david@ixit.czSigned-off-by:
-
David Heidelberg authored
Fixes if condition, which never worked inside mdp4_kms_init, since HW detection has been done later in mdp4_hw_init. Fixes: eb2b47bb ("drm/msm/mdp4: only use lut_clk on mdp4.2+") Signed-off-by:
-
David Heidelberg authored
Inspired by MDP5 code. Also use DRM_DEV_INFO for MDP version as MDP5 does. Cosmetic change: uint32_t -> u32 - checkpatch suggestion. Signed-off-by:
-
Wei Li authored
When it fail to create crtc_event kthread, it just jump to err_msm_uninit, while the 'ret' is not updated. So assign the return code before that. Fixes: 25fdd593 ("drm/msm: Add SDM845 DPU support") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wei Li <liwei391@huawei.com> Reviewed-by:
-
Dmitry Baryshkov authored
None of supported devies uses "gdsc" regulator for DSI. GDSC support is now implemented as a power domain. Drop old code and config handling gdsc regulator requesting and enabling. Signed-off-by:
-
Jonathan Marek authored
Add the required changes to support 7nm pll/phy in CPHY mode. This adds a "qcom,dsi-phy-cphy-mode" property for the PHY node to enable the CPHY mode. Signed-off-by:
Jonathan Marek <jonathan@marek.ca> Reviewed-by:
-
Jonathan Marek authored
Document a new phy-type property which will be used to determine whether the phy should operate in D-PHY or C-PHY mode. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://lore.kernel.org/r/20210617144349.28448-3-jonathan@marek.caAcked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Jonathan Marek authored
These got lost when going from .txt to .yaml bindings, add them back. Signed-off-by:
-
Baokun Li authored
Using list_move_tail() instead of list_del() + list_add_tail() in msm_gem.c. Reported-by:
Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20210609072838.1369371-1-libaokun1@huawei.comReviewed-by:
-
Douglas Anderson authored
Let's use the newly-added nvmem_cell_read_variable_le_u32() to future proof ourselves a little bit. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210521134516.v2.1.Id496c6fea0cb92ff6ea8ef1faf5d468eb09465e3@changeidReviewed-by:
-
Rob Clark authored
On a5xx and a6xx devices that are using CP_WHERE_AM_I to update a ringbuffer read-ptr shadow value, periodically emit a CP_WHERE_AM_I every 32 commands, so that a later submit waiting for ringbuffer space to become available sees partial progress, rather than not seeing rptr advance at all until the GPU gets to the end of the submit that it is currently chewing on. Signed-off-by:
Jordan Crouse <jordan@cosmicpenguin.net> Link: https://lore.kernel.org/r/20210428193654.1498482-3-robdclark@gmail.comSigned-off-by:
-
Thomas Zimmermann authored
Moving the driver-specific mmap code into a GEM object function allows for using DRM helpers for various mmap callbacks. The respective msm functions are being removed. The file_operations structure fops is now being created by the helper macro DEFINE_DRM_GEM_FOPS(). v2: * rebase onto latest upstream * remove declaration of msm_gem_mmap_obj() from msm_fbdev.c Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Link: https://lore.kernel.org/r/20210706084753.8194-1-tzimmermann@suse.de [squash in missing VM_DONTEXPAND flag] Signed-off-by:
-
Bjorn Andersson authored
This patch adds a Adreno 680 entry to the gpulist. Signed-off-by:
-
- 31 Jul, 2021 2 commits
-
-
Akhil P Oommen authored
This patch adds support for the gpu found in the Snapdragon 7c Gen 3 compute platform. This gpu is similar to the exisiting a660 gpu with minor delta in the programing sequence. As the Adreno GPUs are moving away from a numeric chipid based naming scheme to a string, it was decided to use 0x06030500 as the chip id of this gpu to communicate to the userspace driver. Signed-off-by:
Akhil P Oommen <akhilpo@codeaurora.org> Link: https://lore.kernel.org/r/20210730011945.v4.3.I610377db0934b6b7deda532ec2bf786a02c38c01@changeidSigned-off-by:
-
Akhil P Oommen authored
Use rev instead of revn to identify the SKU. This is in preparation to the introduction of 7c3 gpu which won't have a revn. Signed-off-by:
-
