- 31 Dec, 2019 13 commits
-
-
Sasha Neftin authored
The function description for igc_alloc_rx_buffers has not reflected the function meaning. Add meaningful description. Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
The function description for igc_is_non_eop includes an extra @skb parameter description. This parameter doesn't exist on the function, so remove it. Suggested-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
-
Sasha Neftin authored
Use the pci_release_mem_regions method instead of the pci_release_selected_regions method Signed-off-by:
-
Sasha Neftin authored
Improve the probe flow and set both the DMA mask and the coherent to the same thing. Make the flow optimized and cleared. Signed-off-by:
-
Sasha Neftin authored
Scatter gather is used to do DMA data transfers of data that is written to noncontiguous areas of memory. This patch enables scatter gather support. Signed-off-by:
-
Robert Beckett authored
If Rx flow control has been enabled (via autoneg or forced), packets should not be dropped due to Rx descriptor ring exhaustion. Instead pause frames should be used to apply back pressure. This only applies if VFs are not in use. Move SRRCTL setup to its own function for easy reuse and only set drop enable bit if Rx flow control is not enabled. Since v1: always enable dropping of packets if VFs in use. Signed-off-by:
Robert Beckett <bob.beckett@collabora.com> Tested-by:
-
Vijay Khemka authored
gma_flag was set at the time of GMA command request but it should only be set after getting successful response. Movinng this flag setting in GMA response handler. This flag is used mainly for not repeating GMA command once received MAC address. Signed-off-by:
Vijay Khemka <vijaykhemka@fb.com> Reviewed-by:
Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kevin Kou authored
sctp_outq_sack is the main function handles SACK, it is called very frequently. As the commit "move trace_sctp_probe_path into sctp_outq_sack" added below code to this function, sctp tracepoint is disabled most of time, but the loop of transport list will be always called even though the tracepoint is disabled, this is unnecessary. + /* SCTP path tracepoint for congestion control debugging. */ + list_for_each_entry(transport, transport_list, transports) { + trace_sctp_probe_path(transport, asoc); + } This patch is to add tracepoint enabled check at outside of the loop of transport list, and avoid traversing the loop when trace is disabled, it is a small optimization. Signed-off-by:Kevin Kou <qdkevin.kou@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Improvements to SJA1105 DSA RX timestamping This series makes the sja1105 DSA driver use a dedicated kernel thread for RX timestamping, a process which is time-sensitive and otherwise a bit fragile. This allows users to customize their system (probabil an embedded PTP switch) fully and allocate the CPU bandwidth for the driver to expedite the RX timestamps as quickly as possible. While doing this conversion, add a function to the PTP core for cancelling this kernel thread (function which I found rather strange to be missing). ==================== Signed-off-by: -
Vladimir Oltean authored
When disabling PTP timestamping, don't reset the switch with the new static config until all existing PTP frames have been timestamped on the RX path or dropped. There's nothing we can do with these afterwards. Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
And move the queue of skb's waiting for RX timestamps into the ptp_data structure, since it isn't needed if PTP is not compiled. Signed-off-by:
-
Vladimir Oltean authored
In order to effectively use the PTP kernel thread for tasks such as timestamping packets, allow the user control over stopping it, which is needed e.g. when the timestamping queues must be drained. Signed-off-by:
-
Christophe JAILLET authored
'eth_zero_addr()' is already called in the error handling path. This is harmless, but there is no point in calling it twice, so remove one. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
- 30 Dec, 2019 2 commits
-
-
Eric Dumazet authored
Neal Cardwell suggested to not change ca->delay_min and apply the ack delay cushion only when Hystart ACK train is still under consideration. This should avoid a 64bit divide unless needed. Tested: 40Gbit(mlx4) testbed (with sch_fq as packet scheduler) $ echo -n 'file tcp_cubic.c +p' >/sys/kernel/debug/dynamic_debug/control $ nstat -n;for f in {1..10}; do ./super_netperf 1 -H lpaa24 -l -4000000; done;nstat|egrep "Hystart" 14815 16280 15293 15563 11574 15145 14789 18548 16972 12520 TcpExtTCPHystartTrainDetect 10 0.0 TcpExtTCPHystartTrainCwnd 1396 0.0 $ dmesg | tail -10 [ 4873.951350] hystart_ack_train (116 > 93) delay_min 24 (+ ack_delay 69) cwnd 80 [ 4875.155379] hystart_ack_train (55 > 50) delay_min 21 (+ ack_delay 29) cwnd 160 [ 4876.333921] hystart_ack_train (69 > 62) delay_min 23 (+ ack_delay 39) cwnd 130 [ 4877.519037] hystart_ack_train (69 > 60) delay_min 22 (+ ack_delay 38) cwnd 130 [ 4878.701559] hystart_ack_train (87 > 63) delay_min 24 (+ ack_delay 39) cwnd 160 [ 4879.844597] hystart_ack_train (93 > 50) delay_min 21 (+ ack_delay 29) cwnd 216 [ 4880.956650] hystart_ack_train (74 > 67) delay_min 20 (+ ack_delay 47) cwnd 108 [ 4882.098500] hystart_ack_train (61 > 57) delay_min 23 (+ ack_delay 34) cwnd 130 [ 4883.262056] hystart_ack_train (72 > 67) delay_min 21 (+ ack_delay 46) cwnd 130 [ 4884.418760] hystart_ack_train (74 > 67) delay_min 29 (+ ack_delay 38) cwnd 152 10Gbit(bnx2x) testbed (with sch_fq as packet scheduler) $ echo -n 'file tcp_cubic.c +p' >/sys/kernel/debug/dynamic_debug/control $ nstat -n;for f in {1..10}; do ./super_netperf 1 -H lpk52 -l -4000000; done;nstat|egrep "Hystart" 7050 7065 7100 6900 7202 7263 7189 6869 7463 7034 TcpExtTCPHystartTrainDetect 10 0.0 TcpExtTCPHystartTrainCwnd 3199 0.0 $ dmesg | tail -10 [ 176.920012] hystart_ack_train (161 > 141) delay_min 83 (+ ack_delay 58) cwnd 264 [ 179.144645] hystart_ack_train (164 > 159) delay_min 120 (+ ack_delay 39) cwnd 444 [ 181.354527] hystart_ack_train (214 > 168) delay_min 125 (+ ack_delay 43) cwnd 436 [ 183.539565] hystart_ack_train (170 > 147) delay_min 96 (+ ack_delay 51) cwnd 326 [ 185.727309] hystart_ack_train (177 > 160) delay_min 61 (+ ack_delay 99) cwnd 128 [ 187.947142] hystart_ack_train (184 > 167) delay_min 123 (+ ack_delay 44) cwnd 367 [ 190.166680] hystart_ack_train (230 > 153) delay_min 116 (+ ack_delay 37) cwnd 444 [ 192.327285] hystart_ack_train (210 > 206) delay_min 86 (+ ack_delay 120) cwnd 152 [ 194.511392] hystart_ack_train (173 > 151) delay_min 94 (+ ack_delay 57) cwnd 239 [ 196.736023] hystart_ack_train (149 > 146) delay_min 105 (+ ack_delay 41) cwnd 399 Fixes: 42f3a8aa ("tcp_cubic: tweak Hystart detection for short RTT flows") Signed-off-by:Eric Dumazet <edumazet@google.com> Reported-by:
Neal Cardwell <ncardwell@google.com> Link: https://www.spinics.net/lists/netdev/msg621886.html Link: https://www.spinics.net/lists/netdev/msg621797.htmlAcked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter updates for net-next The following patchset contains Netfilter updates for net-next: 1) Remove #ifdef pollution around nf_ingress(), from Lukas Wunner. 2) Document ingress hook in netdevice, also from Lukas. 3) Remove htons() in tunnel metadata port netlink attributes, from Xin Long. 4) Missing erspan netlink attribute validation also from Xin Long. 5) Missing erspan version in tunnel, from Xin Long. 6) Missing attribute nest in NFTA_TUNNEL_KEY_OPTS_{VXLAN,ERSPAN} Patch from Xin Long. 7) Missing nla_nest_cancel() in tunnel netlink dump path, from Xin Long. 8) Remove two exported conntrack symbols with no clients, from Florian Westphal. 9) Add nft_meta_get_eval_time() helper to nft_meta, from Florian. 10) Add nft_meta_pkttype helper for loopback, also from Florian. 11) Add nft_meta_socket uid helper, from Florian Westphal. 12) Add nft_meta_cgroup helper, from Florian. 13) Add nft_meta_ifkind helper, from Florian. 14) Group all interface related meta selector, from Florian. 15) Add nft_prandom_u32() helper, from Florian. 16) Add nft_meta_rtclassid helper, from Florian. 17) Add support for matching on the slave device index, from Florian. This batch, among other things, contains updates for the netfilter tunnel netlink interface: This extension is still incomplete and lacking proper userspace support which is actually my fault, I did not find the time to go back and finish this. This update is breaking tunnel UAPI in some aspects to fix it but do it better sooner than never. ==================== Signed-off-by:
-
- 28 Dec, 2019 25 commits
-
-
David S. Miller authored
Vladimir Oltean says: ==================== The DSA TX timestamping situation This series is the moral v2 of "[PATCH net] net: dsa: sja1105: Fix double delivery of TX timestamps to socket error queue" [0] which did not manage to convince public opinion (actually it didn't convince me neither). This fixes PTP timestamping on one particular board, where the DSA switch is sja1105 and the master is gianfar. Unfortunately there is no way to make the fix more general without committing logical inaccuracies: the SKBTX_IN_PROGRESS flag does serve a purpose, even if the sja1105 driver is not using it now: it prevents delivering a SW timestamp to the app socket when the HW timestamp will be provided. So not setting this flag (the approach from v1) might create avoidable complications in the future (not to mention that there isn't any satisfactory explanation on why that would be the correct solution). So the goal of this change set is to create a more strict framework for DSA master devices when attached to PTP switches, and to fix the first master driver that is overstepping its duties and is delivering unsolicited TX timestamps. [0]: https://www.spinics.net/lists/netdev/msg619699.html ==================== Signed-off-by:
-
Vladimir Oltean authored
It is possible to kill PTP on a DSA switch completely and absolutely, until a reboot, with a simple command: tcpdump -i eth2 -j adapter_unsynced where eth2 is the switch's DSA master. Why? Well, in short, the PTP API in place today is a bit rudimentary and relies on applications to retrieve the TX timestamps by polling the error queue and looking at the cmsg structure. But there is no timestamp identification of any sorts (except whether it's HW or SW), you don't know how many more timestamps are there to come, which one is this one, from whom it is, etc. In other words, the SO_TIMESTAMPING API is fundamentally limited in that you can get a single HW timestamp from the stack. And the "-j adapter_unsynced" flag of tcpdump enables hardware timestamping. So let's imagine what happens when the DSA master decides it wants to deliver TX timestamps to the skb's socket too: - The timestamp that the user space sees is taken by the DSA master. Whereas the RX timestamp will eventually be overwritten by the DSA switch. So the RX and TX timestamps will be in different time bases (aka garbage). - The user space applications have no way to deal with the second (real) TX timestamp finally delivered by the DSA switch, or even to know to wait for it. Take ptp4l from the linuxptp project, for example. This is its behavior after running tcpdump, before the patch: ptp4l[172]: [6469.594] Unexpected data on socket err queue: ptp4l[172]: [6469.693] rms 8 max 16 freq -21257 +/- 11 delay 748 +/- 0 ptp4l[172]: [6469.711] Unexpected data on socket err queue: ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 05 00 fd ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: [6469.721] Unexpected data on socket err queue: ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02 ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b1 00 fd ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: [6469.838] Unexpected data on socket err queue: ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02 ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 06 00 fd ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: [6469.848] Unexpected data on socket err queue: ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 13 02 ptp4l[172]: 0010 00 36 00 00 02 00 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 04 1a 45 05 7f ptp4l[172]: 0030 00 00 5e 05 41 32 27 c2 1a 68 00 04 9f ff fe 05 ptp4l[172]: 0040 de 06 00 01 ptp4l[172]: [6469.855] Unexpected data on socket err queue: ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02 ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b2 00 fd ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: [6469.974] Unexpected data on socket err queue: ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02 ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00 ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 07 00 fd ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00 The ptp4l program itself is heavily patched to show this (more details here [0]). Otherwise, by default it just hangs. On the other hand, with the DSA patch to disallow HW timestamping applied: tcpdump -i eth2 -j adapter_unsynced tcpdump: SIOCSHWTSTAMP failed: Device or resource busy So it is a fact of life that PTP timestamping on the DSA master is incompatible with timestamping on the switch MAC, at least with the current API. And if the switch supports PTP, taking the timestamps from the switch MAC is highly preferable anyway, due to the fact that those don't contain the queuing latencies of the switch. So just disallow PTP on the DSA master if there is any PTP-capable switch attached. [0]: https://sourceforge.net/p/linuxptp/mailman/message/36880648/ Fixes: 0336369d ("net: dsa: forward hardware timestamping ioctls to switch driver") Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
The driver wrongly assumes that it is the only entity that can set the SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the gfar_clean_tx_ring function, where the TX timestamp is collected if necessary, the aforementioned bit is used to discriminate whether or not the TX timestamp should be delivered to the socket's error queue. But a stacked driver such as a DSA switch can also set the SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in order to denote that the hardware timestamping process is undergoing. Therefore, gianfar would misinterpret the "in progress" bit as being its own, and deliver a second skb clone in the socket's error queue, completely throwing off a PTP process which is not expecting to receive it, _even though_ TX timestamping is not enabled for gianfar. There have been discussions [0] as to whether non-MAC drivers need or not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2 timestamps, a sw and a hw one, to applications which only expect one). But as of this patch, there are at least 2 PTP drivers that would break in conjunction with gianfar: the sja1105 DSA switch and the felix switch, by way of its ocelot core driver. So regardless of that conclusion, fix the gianfar driver to not do stuff based on flags set by others and not intended for it. [0]: https://www.spinics.net/lists/netdev/msg619699.html Fixes: f0ee7acf ("gianfar: Add hardware TX timestamping support") Signed-off-by:
-
Chen Zhou authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wan/fsl_ucc_hdlc.c: In function ucc_hdlc_irq_handler: drivers/net/wan/fsl_ucc_hdlc.c:643:23: warning: variable ut_info set but not used [-Wunused-but-set-variable] drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_suspend: drivers/net/wan/fsl_ucc_hdlc.c:880:23: warning: variable ut_info set but not used [-Wunused-but-set-variable] drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_resume: drivers/net/wan/fsl_ucc_hdlc.c:925:6: warning: variable ret set but not used [-Wunused-but-set-variable] Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Chen Zhou <chenzhou10@huawei.com> Signed-off-by:
-
David S. Miller authored
Michal Kubecek says: ==================== ethtool netlink interface, part 1 This is first part of netlink based alternative userspace interface for ethtool. It aims to address some long known issues with the ioctl interface, mainly lack of extensibility, raciness, limited error reporting and absence of notifications. The goal is to allow userspace ethtool utility to provide all features it currently does but without using the ioctl interface. However, some features provided by ethtool ioctl API will be available through other netlink interfaces (rtnetlink, devlink) if it's more appropriate. The interface uses generic netlink family "ethtool" and provides multicast group "monitor" which is used for notifications. Documentation for the interface is in Documentation/networking/ethtool-netlink.rst file. The netlink interface is optional, it is built when CONFIG_ETHTOOL_NETLINK (bool) option is enabled. There are three types of request messages distinguished by suffix "_GET" (query for information), "_SET" (modify parameters) and "_ACT" (perform an action). Kernel reply messages have name with additional suffix "_REPLY" (e.g. ETHTOOL_MSG_SETTINGS_GET_REPLY). Most "_SET" and "_ACT" message types do not have matching reply type as only some of them need additional reply data beyond numeric error code and extack. Kernel also broadcasts notification messages ("_NTF" suffix) on changes. Basic concepts: - make extensions easier not only by allowing new attributes but also by imposing as few artificial limits as possible, e.g. by using arbitrary size bit sets for most bitmap attributes or by not using fixed size strings - use extack for error reporting and warnings - send netlink notifications on changes (even if they were done using the ioctl interface) and actions - avoid the racy read/modify/write cycle between kernel and userspace by sending only attributes which userspace wants to change; there is still a read/modify/write cycle between generic kernel code and ethtool_ops handler in NIC driver but it is only in kernel and under RTNL lock - reduce the number of name lists that need to be kept in sync between kernel and userspace (e.g. recognized link modes) - where feasible, allow dump requests to query specific information for all network devices - as parsing and generating netlink messages is more complicated than simply copying data structures between userspace API and ethtool_ops handlers (which most ioctl commands do), split the code into multiple files in net/ethtool directory; move net/core/ethtool.c also to this directory and rename it to ioctl.c Changes between v8 and v9: - fix ethnl_update_u8() - fix description of ETHTOOL_A_LINKSTATE_LINK in rst file - add explanation of verbose vs. compact bitset usage to documentation - link ethtool-netlink.rst into toctree Main changes between v7 and v8: - preliminary patches sent as a separate series (already in net-next) - split notification related changes out of _SET patches - drop request specific flags from common header - use FLAG/flag rather than GFLAG/gflag for global flags (as there are only global flags now) - allow device names up to ALTIFNAMSIZ characters - rename ETHTOOL_A_BITSET_LIST to ETHTOOL_A_BITSET_NOMASK - rename ETHTOOL_A_BIT{,S}_* to ETHTOOL_A_BITSET_BIT{,S}_* - use standard bitset helpers for link modes (rather than in-place conversion) - use "default" rather than "standard" for unified _GET handlers - fixed 64-bit big endian bitset code Main changes between v6 and v7: - split complex messages into small single purpose ones (drop info and request masks and one level of nesting) - separate request information and reply data into two structures - refactor bitset handling (no simultaneous u32/ulong handling but avoid kmalloc() except for long bitmaps on 64-bit big endian architectures) - use only fixed size strings internally (will be replaced by char * eventually but that will require rewriting also existing ioctl code) - rework ethnl_update_* helpers to return error code - rename request flag constants (to ETHTOOL_[GR]FLAG_ prefix) - convert documentation to rst Main changes between v5 and v6: - use ETHTOOL_MSG_ prefix for message types - replace ETHA_ prefix for netlink attributes by ETHTOOL_A_ - replace ETH_x_IM_y for infomask bits by ETHTOOL_IM_x_y - split GET reply types from SET requests and notifications - split kernel and userspace message types into different enums - remove INFO_GET requests from submitted part - drop EVENT notifications (use rtnetlink and on-demand string set load) - reorganize patches to reduce the number of intermitent warnings - unify request/reply header and its processing - another nest around strings in a string set for consistency - more consistent identifier naming - coding style cleanup - get rid of some of the helpers - set bad attribute in extack where applicable - various bug fixes - improve documentation and code comments, more kerneldoc comments - more verbose commit messages Changes between v4 and v5: - do not panic on failed initialization, only WARN() Main changes between RFC v3 and v4: - use more kerneldoc style comments - strict attribute policy checking - use macros for tables of link mode names and parameters - provide permanent hardware address in rtnetlink - coding style cleanup - split too long patches, reorder - wrap more ETHA_SETTINGS_* attributes in nests - add also some SET_* implementation into submitted part Main changes between RFC v2 and RFC v3: - do not allow building as a module (no netdev notifiers needed) - drop some obsolete fields - add permanent hw address, timestamping and private flags support - rework bitset handling to get rid of variable length arrays - notify monitor on device renames - restructure GET_SETTINGS/SET_SETTINGS messages - split too long patches and submit only first part of the series Main changes between RFC v1 and RFC v2: - support dumps for all "get" requests - provide notifications for changes related to supported request types - support getting string sets (both global and per device) - support getting/setting device features - get rid of family specific header, everything passed as attributes - split netlink code into multiple files in net/ethtool/ directory ==================== Signed-off-by: -
Michal Kubecek authored
Implement LINKSTATE_GET netlink request to get link state information. At the moment, only link up flag as provided by ETHTOOL_GLINK ioctl command is returned. LINKSTATE_GET request can be used with NLM_F_DUMP (without device identification) to request the information for all devices in current network namespace providing the data. Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Michal Kubecek authored
Send ETHTOOL_MSG_LINKMODES_NTF notification message whenever device link settings or advertised modes are modified using ETHTOOL_MSG_LINKMODES_SET netlink message or ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands. The notification message has the same format as reply to LINKMODES_GET request. ETHTOOL_MSG_LINKMODES_SET netlink request only triggers the notification if there is a change but the ioctl command handlers do not check if there is an actual change and trigger the notification whenever the commands are executed. As all work is done by ethnl_default_notify() handler and callback functions introduced to handle LINKMODES_GET requests, all that remains is adding entries for ETHTOOL_MSG_LINKMODES_NTF into ethnl_notify_handlers and ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where needed. Signed-off-by:
-
Michal Kubecek authored
Implement LINKMODES_SET netlink request to set advertised linkmodes and related attributes as ETHTOOL_SLINKSETTINGS and ETHTOOL_SSET commands do. The request allows setting autonegotiation flag, speed, duplex and advertised link modes. Signed-off-by:
-
Michal Kubecek authored
Implement LINKMODES_GET netlink request to get link modes related information provided by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl commands. This request provides supported, advertised and peer advertised link modes, autonegotiation flag, speed and duplex. LINKMODES_GET request can be used with NLM_F_DUMP (without device identification) to request the information for all devices in current network namespace providing the data. Signed-off-by:
-
Michal Kubecek authored
Send ETHTOOL_MSG_LINKINFO_NTF notification message whenever device link settings are modified using ETHTOOL_MSG_LINKINFO_SET netlink message or ETHTOOL_SLINKSETTINGS or ETHTOOL_SSET ioctl commands. The notification message has the same format as reply to LINKINFO_GET request. ETHTOOL_MSG_LINKINFO_SET netlink request only triggers the notification if there is a change but the ioctl command handlers do not check if there is an actual change and trigger the notification whenever the commands are executed. As all work is done by ethnl_default_notify() handler and callback functions introduced to handle LINKINFO_GET requests, all that remains is adding entries for ETHTOOL_MSG_LINKINFO_NTF into ethnl_notify_handlers and ethnl_default_notify_ops lookup tables and calls to ethtool_notify() where needed. Signed-off-by:
-
Michal Kubecek authored
The ethtool netlink notifications have the same format as related GET replies so that if generic GET handling framework is used to process GET requests, its callbacks and instance of struct get_request_ops can be also used to compose corresponding notification message. Provide function ethnl_std_notify() to be used as notification handler in ethnl_notify_handlers table. Signed-off-by:
-
Michal Kubecek authored
Implement LINKINFO_SET netlink request to set link settings queried by LINKINFO_GET message. Only physical port, phy MDIO address and MDI(-X) control can be set, attempt to modify MDI(-X) status and transceiver is rejected. Signed-off-by:
-
Michal Kubecek authored
Implement LINKINFO_GET netlink request to get basic link settings provided by ETHTOOL_GLINKSETTINGS and ETHTOOL_GSET ioctl commands. This request provides settings not directly related to autonegotiation and link mode selection: physical port, phy MDIO address, MDI(-X) status, MDI(-X) control and transceiver. LINKINFO_GET request can be used with NLM_F_DUMP (without device identification) to request the information for all devices in current network namespace providing the data. Signed-off-by:
-
Michal Kubecek authored
Requests a contents of one or more string sets, i.e. indexed arrays of strings; this information is provided by ETHTOOL_GSSET_INFO and ETHTOOL_GSTRINGS commands of ioctl interface. Unlike ioctl interface, all information can be retrieved with one request and mulitple string sets can be requested at once. There are three types of requests: - no NLM_F_DUMP, no device: get "global" stringsets - no NLM_F_DUMP, with device: get string sets related to the device - NLM_F_DUMP, no device: get device related string sets for all devices Client can request either all string sets of given type (global or device related) or only specific sets. With ETHTOOL_A_STRSET_COUNTS flag set, only set sizes (numbers of strings) are returned. Signed-off-by:
-
Michal Kubecek authored
Significant part of GET request processing is common for most request types but unfortunately it cannot be easily separated from type specific code as we need to alternate between common actions (parsing common request header, allocating message and filling netlink/genetlink headers etc.) and specific actions (querying the device, composing the reply). The processing also happens in three different situations: "do" request, "dump" request and notification, each doing things in slightly different way. The request specific code is implemented in four or five callbacks defined in an instance of struct get_request_ops: parse_request() - parse incoming message prepare_data() - retrieve data from driver or NIC reply_size() - estimate reply message size fill_reply() - compose reply message cleanup_data() - (optional) clean up additional data Other members of struct get_request_ops describe the data structure holding information from client request and data used to compose the message. The default handlers ethnl_default_doit(), ethnl_default_dumpit(), ethnl_default_start() and ethnl_default_done() can be then used in genl_ops handler. Notification handler will be introduced in a later patch. Signed-off-by:
-
Michal Kubecek authored
Add infrastructure for ethtool netlink notifications. There is only one multicast group "monitor" which is used to notify userspace about changes and actions performed. Notification messages (types using suffix _NTF) share the format with replies to GET requests. Notifications are supposed to be broadcasted on every configuration change, whether it is done using the netlink interface or ioctl one. Netlink SET requests only trigger a notification if some data is actually changed. To trigger an ethtool notification, both ethtool netlink and external code use ethtool_notify() helper. This helper requires RTNL to be held and may sleep. Handlers sending messages for specific notification message types are registered in ethnl_notify_handlers array. As notifications can be triggered from other code, ethnl_ok flag is used to prevent an attempt to send notification before genetlink family is registered. Signed-off-by:
-
Michal Kubecek authored
The ethtool netlink code uses common framework for passing arbitrary length bit sets to allow future extensions. A bitset can be a list (only one bitmap) or can consist of value and mask pair (used e.g. when client want to modify only some bits). A bitset can use one of two formats: verbose (bit by bit) or compact. Verbose format consists of bitset size (number of bits), list flag and an array of bit nests, telling which bits are part of the list or which bits are in the mask and which of them are to be set. In requests, bits can be identified by index (position) or by name. In replies, kernel provides both index and name. Verbose format is suitable for "one shot" applications like standard ethtool command as it avoids the need to either keep bit names (e.g. link modes) in sync with kernel or having to add an extra roundtrip for string set request (e.g. for private flags). Compact format uses one (list) or two (value/mask) arrays of 32-bit words to store the bitmap(s). It is more suitable for long running applications (ethtool in monitor mode or network management daemons) which can retrieve the names once and then pass only compact bitmaps to save space. Userspace requests can use either format; ETHTOOL_FLAG_COMPACT_BITSETS flag in request header tells kernel which format to use in reply. Notifications always use compact format. As some code uses arrays of unsigned long for internal representation and some arrays of u32 (or even a single u32), two sets of parse/compose helpers are introduced. To avoid code duplication, helpers for unsigned long arrays are implemented as wrappers around helpers for u32 arrays. There are two reasons for this choice: (1) u32 arrays are more frequent in ethtool code and (2) unsigned long array can be always interpreted as an u32 array on little endian 64-bit and all 32-bit architectures while we would need special handling for odd number of u32 words in the opposite direction. Signed-off-by:
-
Michal Kubecek authored
Add common request/reply header definition and helpers to parse request header and fill reply header. Provide ethnl_update_* helpers to update structure members from request attributes (to be used for *_SET requests). Signed-off-by:
-
Michal Kubecek authored
Basic genetlink and init infrastructure for the netlink interface, register genetlink family "ethtool". Add CONFIG_ETHTOOL_NETLINK Kconfig option to make the build optional. Add initial overall interface description into Documentation/networking/ethtool-netlink.rst, further patches will add more detailed information. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Kevin Kou authored
The function sctp_sf_eat_sack_6_2 now performs the Verification Tag validation, Chunk length validation, Bogu check, and also the detection of out-of-order SACK based on the RFC2960 Section 6.2 at the beginning, and finally performs the further processing of SACK. The trace_sctp_probe now triggered before the above necessary validation and check. this patch is to do the trace_sctp_probe after the chunk sanity tests, but keep doing trace if the SACK received is out of order, for the out-of-order SACK is valuable to congestion control debugging. v1->v2: - keep doing SCTP trace if the SACK is out of order as Marcelo's suggestion. v2->v3: - regenerate the patch as v2 generated on top of v1, and add 'net-next' tag to the new one as Marcelo's comments. Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Nikita Yushchenko authored
If packet checker is enabled in the serdes, then Rx counter registers start working, and no side effects have been detected. This patch enables packet checker automatically when powering serdes on, and exposes Rx counter registers via ethtool statistics interface. Code partially basded by older attempt by Andrew Lunn. Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by:
-
YueHaibing authored
drivers/net/ethernet/amazon/ena/ena_netdev.c: In function ena_xdp_xmit_buff: drivers/net/ethernet/amazon/ena/ena_netdev.c:316:19: warning: variable rx_ring set but not used [-Wunused-but-set-variable] commit 548c4940 ("net: ena: Implement XDP_TX action") left behind this unused variable. Reported-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Mao Wenan authored
There is no need to set variable 'mbus' static since new value always be assigned before use it. Signed-off-by:
Mao Wenan <maowenan@huawei.com> Reviewed-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
-
Xu Wang authored
Passing NULL to ppp_pernet causes a crash via BUG_ON. Dereferencing net in net_generic() also has the same effect. This patch removes the redundant BUG_ON check on the same parameter. Signed-off-by:
Xu Wang <vulab@iscas.ac.cn> Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== tcp_cubic: various fixes This patch series converts tcp_cubic to usec clock resolution for Hystart logic. This makes Hystart more relevant for data-center flows. Prior to this series, Hystart was not kicking, or was kicking without good reason, since the 1ms clock was too coarse. Last patch also fixes an issue with Hystart vs TCP pacing. v2: removed a last-minute debug chunk from last patch ==================== Signed-off-by:
-
