- simplify the driver
- there are a lot of quirky racy conditions not handled
- causes more aborts/resets when the number of commands to be aborted is
  large, such as in multi-path fail-overs.
- has been turned off in our internal driver since 8/31/2015
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

- Block I/O requests with 0 length transfers which go down the ioaccel
  path. This causes lockup issues down in the basecode.
- These issues have been fixed, but there are customers who are
  experiencing the issues when running older firmware.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

create new worker thread to monitor controller events
 - both the rescan and event monitor workers can cause a rescan to occur
   however for multipath we have found that we need to respond faster
   than the normal scheduled rescan interval for path fail-overs.
 - getting controller events only involves reading a register, but the
   rescan worker can obtain an updated LUN list when there is a PTRAID
   device present.
 - move common code to a separate function.
advantages:
 - detect controller events more frequently.
 - leave rescan thread interval at 30 seconds.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

- queue depth assignment not in correct place, had no effect.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

- mark device state sooner.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

- call scsi_done when the command completes.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

- schedule another scan.
- mark current scan as completed.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Prevent enclosure resets.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.tell@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Use the return from TUR as a check for the device state.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.tell@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

external shelves do not support BMICs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

- align with latest spec.
- added __attribute((aligned(512)))
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Update the driver version to 50834
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Remove reference to Series-9 HBA and created arc ctrl check function.
Signed-off-by: Prasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Added info and error messages in controller reset function to log
information about the status of the IOP/SOFT reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Make sure that IOP and SOFT reset are enabled for both for both arc and
hba1000 controllers.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Made sure that ioctl commands return in case of a controller reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The command thread checks the ctrl health periodically before sending
updates to the controller. The function that it uses is aac_check_health
which does more than get the health status.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Removed switch case and replaced with if mask checks. Moved KERNEL_PANIC
check to when bled is less than 0.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Now the driver issues a soft reset and waits for the controller to be up
and running by periodically checking on the status of the controller
health registers. Also prevents ARC adapters from issuing soft reset if
IOP resets failed.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Added function that waits with a timeout for the ctrl to be up and running
after triggering an IOP reset. Also removed 30 sec sleep as it is not
needed.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Reworked IOP reset to remove unneeded variable and created a helper
function to notify fw of an imminent IOP reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The driver can now trigger IOP reset with a single reset mask. Removed
code that retrieves a reset_mask from the firmware.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Log the status of the controller before issuing a reset.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Log the location of the scsi cmds before triggering a reset. This
information is useful for debugging.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Change the completion wait time for the fibs in the reset and abort
callback from 2 minutes to 15 seconds.

2 minutes is too long for waiting for completion.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Check health does not need to reset the ctrl but just return the
controller health status.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The default queue depth for non NATIVE RAW disks is calculated from the
number of fibs and number of disks or a max of 256. This causes poor disk
IO performance.

The fix is to set default qd based on the type of disks
(SATA -32 and SAS -64)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The qd for ARC Native disks is calculated by dividing the max IO 1024
by the number of disks or 256 which ever is lower. This causes poor
disk IO performance.

The fix is set the qd based on the type of disk (SAS - 64 and SATA -
32).
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The driver changed the DMA consistent map after consistent memory was
allocated, this invalidated the IOMMU identity mapping. The fix was to
make sure that we set the DMA consistent mask setting once depending on
the controller card.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The raw srb commands do not requires memory that in the ZONE_DMA memory
space. For 32bit srb commands use GFP_DMA32 to limit the memory to 32bit
memory range (4GB).
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull key subsystem fixes from James Morris:
 "Here are a bunch of fixes for Linux keyrings, including:

   - Fix up the refcount handling now that key structs use the
     refcount_t type and the refcount_t ops don't allow a 0->1
     transition.

   - Fix a potential NULL deref after error in x509_cert_parse().

   - Don't put data for the crypto algorithms to use on the stack.

   - Fix the handling of a null payload being passed to add_key().

   - Fix incorrect cleanup an uninitialised key_preparsed_payload in
     key_update().

   - Explicit sanitisation of potentially secure data before freeing.

   - Fixes for the Diffie-Helman code"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (23 commits)
  KEYS: fix refcount_inc() on zero
  KEYS: Convert KEYCTL_DH_COMPUTE to use the crypto KPP API
  crypto : asymmetric_keys : verify_pefile:zero memory content before freeing
  KEYS: DH: add __user annotations to keyctl_kdf_params
  KEYS: DH: ensure the KDF counter is properly aligned
  KEYS: DH: don't feed uninitialized "otherinfo" into KDF
  KEYS: DH: forbid using digest_null as the KDF hash
  KEYS: sanitize key structs before freeing
  KEYS: trusted: sanitize all key material
  KEYS: encrypted: sanitize all key material
  KEYS: user_defined: sanitize key payloads
  KEYS: sanitize add_key() and keyctl() key payloads
  KEYS: fix freeing uninitialized memory in key_update()
  KEYS: fix dereferencing NULL payload with nonzero length
  KEYS: encrypted: use constant-time HMAC comparison
  KEYS: encrypted: fix race causing incorrect HMAC calculations
  KEYS: encrypted: fix buffer overread in valid_master_desc()
  KEYS: encrypted: avoid encrypting/decrypting stack buffers
  KEYS: put keyring if install_session_keyring_to_cred() fails
  KEYS: Delete an error message for a failed memory allocation in get_derived_key()
  ...

Commit abb2ea7d ("compiler, clang: suppress warning for unused
static inline functions") just caused more warnings due to re-defining
the 'inline' macro.

So undef it before re-defining it, and also add the 'notrace' attribute
like the gcc version that this is overriding does.

Maybe this makes clang happier.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull randomness fixes from Ted Ts'o:
 "Improve performance by using a lockless update mechanism suggested by
  Linus, and make sure we refresh per-CPU entropy returned get_random_*
  as soon as the CRNG is initialized"

* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: invalidate batched entropy after crng init
  random: use lockless method of accessing and updating f->reg_idx

Pull ext4 fixes from Ted Ts'o:
 "Fix various bug fixes in ext4 caused by races and memory allocation
  failures"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix fdatasync(2) after extent manipulation operations
  ext4: fix data corruption for mmap writes
  ext4: fix data corruption with EXT4_GET_BLOCKS_ZERO
  ext4: fix quota charging for shared xattr blocks
  ext4: remove redundant check for encrypted file on dio write path
  ext4: remove unused d_name argument from ext4_search_dir() et al.
  ext4: fix off-by-one error when writing back pages before dio read
  ext4: fix off-by-one on max nr_pages in ext4_find_unwritten_pgoff()
  ext4: keep existing extra fields when inode expands
  ext4: handle the rest of ext4_mb_load_buddy() ENOMEM errors
  ext4: fix off-by-in in loop termination in ext4_find_unwritten_pgoff()
  ext4: fix SEEK_HOLE
  jbd2: preserve original nofs flag during journal restart
  ext4: clear lockdep subtype for quota files on quota off

Pull GPIO fixes from Linus Walleij:
 "A few overdue GPIO patches for the v4.12 kernel.

   - Fix debounce logic on the Aspeed platform.

   - Fix the "virtual gpio" things on the Intel Crystal Cove.

   - Fix the blink counter selection on the MVEBU platform"

* tag 'gpio-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mvebu: fix gpio bank registration when pwm is used
  gpio: mvebu: fix blink counter register selection
  MAINTAINERS: remove self from GPIO maintainers
  gpio: crystalcove: Do not write regular gpio registers for virtual GPIOs
  gpio: aspeed: Don't attempt to debounce if disabled

Pull char/misc driver fixes from Greg KH:
 "Here are some small driver fixes for 4.12-rc5. Nothing major here,
  just some small bugfixes found by people testing, and a MAINTAINERS
  file update for the genwqe driver.

  All have been in linux-next with no reported issues"

[ The cxl driver fix came in through the powerpc tree earlier ]

* tag 'char-misc-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  cxl: Avoid double free_irq() for psl,slice interrupts
  mei: make sysfs modalias format similar as uevent modalias
  drivers: char: mem: Fix wraparound check to allow mappings up to the end
  MAINTAINERS: Change maintainer of genwqe driver
  goldfish_pipe: use GFP_ATOMIC under spin lock
  firmware: vpd: do not leak kobjects
  firmware: vpd: avoid potential use-after-free when destroying section
  firmware: vpd: do not leave freed section attributes to the list

Pull staging/IIO fixes from Greg KH:
 "These are mostly all IIO driver fixes, resolving a number of tiny
  issues. There's also a ccree and lustre fix in here as well, both fix
  problems found in those codebases.

  All have been in linux-next with no reported issues"

* tag 'staging-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: ccree: fix buffer copy
  staging/lustre/lov: remove set_fs() call from lov_getstripe()
  staging: ccree: add CRYPTO dependency
  iio: adc: sun4i-gpadc-iio: fix parent device being used in devm function
  iio: light: ltr501 Fix interchanged als/ps register field
  iio: adc: bcm_iproc_adc: swap primary and secondary isr handler's
  iio: trigger: fix NULL pointer dereference in iio_trigger_write_current()
  iio: adc: max9611: Fix attribute measure unit
  iio: adc: ti_am335x_adc: allocating too much in probe
  iio: adc: sun4i-gpadc-iio: Fix module autoload when OF devices are registered
  iio: adc: sun4i-gpadc-iio: Fix module autoload when PLATFORM devices are registered
  iio: proximity: as3935: fix iio_trigger_poll issue
  iio: proximity: as3935: fix AS3935_INT mask
  iio: adc: Max9611: checking for ERR_PTR instead of NULL in probe
  iio: proximity: as3935: recalibrate RCO after resume

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 4.12-rc5

  They are for some reported issues in the chipidea and gadget drivers.
  Nothing major. All have been in linux-next for a while with no
  reported issues"

* tag 'usb-4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: gadget: udc: renesas_usb3: Fix PN_INT_ENA disabling timing
  usb: gadget: udc: renesas_usb3: lock for PN_ registers access
  usb: gadget: udc: renesas_usb3: fix deadlock by spinlock
  usb: gadget: udc: renesas_usb3: fix pm_runtime functions calling
  usb: gadget: f_mass_storage: Serialize wake and sleep execution
  usb: dwc2: add support for the DWC2 controller on Meson8 SoCs
  phy: qualcomm: phy-qcom-qmp: fix application of sizeof to pointer
  usb: musb: dsps: keep VBUS on for host-only mode
  usb: chipidea: core: check before accessing ci_role in ci_role_show
  usb: chipidea: debug: check before accessing ci_role
  phy: qcom-qmp: fix return value check in qcom_qmp_phy_create()
  usb: chipidea: udc: fix NULL pointer dereference if udc_start failed
  usb: chipidea: imx: Do not access CLKONOFF on i.MX51

Pull SCSI fixes from James Bottomley:
 "This is a set of user visible fixes (excepting one format string
  change).

  Four of the qla2xxx fixes only affect the firmware dump path, but it's
  still important to the enterprise. The rest are various NULL pointer
  crash conditions or outright driver hangs"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: cxgb4i: libcxgbi: in error case RST tcp conn
  scsi: scsi_debug: Avoid PI being disabled when TPGS is enabled
  scsi: qla2xxx: Fix extraneous ref on sp's after adapter break
  scsi: lpfc: prevent potential null pointer dereference
  scsi: lpfc: Avoid NULL pointer dereference in lpfc_els_abort()
  scsi: lpfc: nvmet_fc: fix format string
  scsi: qla2xxx: Fix crash due to NULL pointer dereference of ctx
  scsi: qla2xxx: Fix mailbox pointer error in fwdump capture
  scsi: qla2xxx: Set bit 15 for DIAG_ECHO_TEST MBC
  scsi: qla2xxx: Modify T262 FW dump template to specify same start/end to debug customer issues
  scsi: qla2xxx: Fix crash due to mismatch mumber of Q-pair creation for Multi queue
  scsi: qla2xxx: Fix NULL pointer access due to redundant fc_host_port_name call
  scsi: qla2xxx: Fix recursive loop during target mode configuration for ISP25XX leaving system unresponsive
  scsi: bnx2fc: fix race condition in bnx2fc_get_host_stats()
  scsi: qla2xxx: don't disable a not previously enabled PCI device