Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2019-02-21

This series adds some misc updates to mlx5 driver,

1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.

2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.

3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
   VEPA/VEB E-Switch legacy mode configurations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add support for new port types and speeds for Spectrum-2

Shalom says:

This patchset adds support for new port types and speeds for Spectrum-2.

Patch #1 + #2 removes an unsupported PTYS field and a duplicate link
mode entry.

Patch #3 queries port's connector type from firmware instead of deriving
it from port admin state.

Patch #4 renames functions which relate to port type-speed to be
Spectrum-1 specific.

Patch #5 defines port type-speed operations and applies it for
Spectrum-1.

Patch #6 + #7 are small renaming and cosmetic changes.

Patch #8 adds new port type-speed fields for PTYS register. These new
fields extend the existing ones in order to support more types and
speeds.

Patch #9 adds Spectrum-2 support for port type-speed operations.

Patch #10 adds Spectrum-2 new port types and speeds.

For Spectrum-2, the user must configure all the types per speed if he /
she wants a specific speed to be advertised. For example, if the user
wants to advertise 100Gbps 4-lanes speed, the following ethtool bits
should be advertised:

  Supported ethtool bits for 100Gbps 4-lanes:
      0x1000000000      100000baseKR4 Full
      0x2000000000      100000baseSR4 Full
      0x4000000000      100000baseCR4 Full
      0x8000000000      100000baseLR4_ER4 Full

  Command for advertising 100Gbps 4-lanes:
      ethtool -s enp3s0np1 advertise 0xF000000000
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Spectrum-2 ASIC support for the following new port types and speeds:
  * 50Gbps 1-lane
  * 100Gbps 2-lanes
  * 200Gbps 4-lanes
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Spectrum-2 ASIC port type-speed operations.

Since multiple ethtool link modes are represented using a single bit in the
ASIC, the driver forces the user to configure all types per a specific
speed. For example, if the user wants to advertise 100Gbps 4-lanes speed,
he should advertise all the types of 100Gbps 4-lanes speed that are
supported by the ASIC as shown below:

  Supported ethtool bits for 100Gbps 4-lanes:
      0x1000000000      100000baseKR4 Full
      0x2000000000      100000baseSR4 Full
      0x4000000000      100000baseCR4 Full
      0x8000000000      100000baseLR4_ER4 Full

  Command for advertising 100Gbps 4-lanes:
      ethtool -s enp3s0np1 advertise 0xF000000000
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PTYS register introduces a new layout for port type-speed fields. These
fields extend the existing ones in order to handle more types and speeds.
For example, the new 200Gbps speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

80 columns wrapping change in mlxsw_reg_ptys_eth_unpack function.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename p_eth_proto_adm to p_eth_proto_admin in mlxsw_reg_ptys_eth_unpack
function.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add port type-speed operations in order to have different operations for
different ASICs. For now, both ASICs use the same pointer.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename port speed-type functions to be Spectrum-1 ASIC specific.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of deriving the port connector type from port admin state, query it
from firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove eth_proto_lp_advertise field in PTYS register since it is not
supported by the firmware.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicate port link mode entry from mlxsw_sp_port_link_mode.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There has check NULL on kmem_cache_create on failure in kcm_init,
no need use SLAB_PANIC to panic the system.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
-Wformat fixes

This is a collection of some -Wformat fixes found during build, nothing
critical, but nice to have for people turning on more warnings with
their builds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide a precision hint to snprintf() in order to eliminate a
-Wformat-truncation warning provided below. A maximum of 11 characters
is allowed to reach a maximum of 32 - 1 characters given a possible
maximum value of queues using up to UINT_MAX which occupies 10
characters. Incidentally 11 is the number of characters for
"xdp_packets" which is the largest string we append.

drivers/net/veth.c: In function 'veth_get_strings':
drivers/net/veth.c:118:47: warning: '%s' directive output may be
truncated writing up to 31 bytes into a region of size between 12 and 21
[-Wformat-truncation=]
     snprintf(p, ETH_GSTRING_LEN, "rx_queue_%u_%s",
                                               ^~
drivers/net/veth.c:118:5: note: 'snprintf' output between 12 and 52
bytes into a destination of size 32
     snprintf(p, ETH_GSTRING_LEN, "rx_queue_%u_%s",
     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
       i, veth_rq_stats_desc[j].desc);
       ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:

drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
     "%s-rx-0", netdev->name);
             ^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
   snprintf(adapter->rx_ring->name,
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     sizeof(adapter->rx_ring->name) - 1,
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     "%s-rx-0", netdev->name);
     ~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
     "%s-tx-0", netdev->name);
             ^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
   snprintf(adapter->tx_ring->name,
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     sizeof(adapter->tx_ring->name) - 1,
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     "%s-tx-0", netdev->name);
     ~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:

drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
  chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
  ^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
    dev_name(chip->dev));
    ^~~~~~~~
  LD [M]  drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:

drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
                                     ^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     mlxsw_sp_port_hw_prio_stats[i].str, prio);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
                                     ^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     mlxsw_sp_port_hw_tc_stats[i].str, tc);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I thought header search paths to tools/include(/uapi) were unneeded,
but it looks like a build error occurs depending on the compiler.

Commit 303a339f ("bpfilter: remove extra header search paths for
bpfilter_umh") reintroduced the build error fixed by commit ae40832e
("bpfilter: fix a build err").

Apology for the breakage, and thanks to Guenter for reporting this.

Fixes: 303a339f ("bpfilter: remove extra header search paths for bpfilter_umh")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vinod Koul says:

====================
net: phy: at803x: Update delays for RGMII modes

Peter[1] reported that patch cd28d1d6: ("net: phy: at803x: Disable
phy delay for RGMII mode") caused regression on am335x-evmsk board.
This board expects the Phy delay to be enabled but specified RGMII mode
which refers to delays being disabled. So fix this by disabling delay only
for RGMII mode and enable for RGMII_ID and RGMII_TXID/RXID modes.

While at it, as pointed by Dave, don't inline the helpers.

[1]: https://www.spinics.net/lists/netdev/msg550749.html

Changes in v4:
 - fix log & comments nbased on Marc's feedback
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.

So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.

Fixes: cd28d1d6: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For tcindex filter, it is too late to initialize the
net pointer in tcf_exts_validate(), as tcf_exts_get_net()
requires a non-NULL net pointer. We can just move its
initialization into tcf_exts_init(), which just requires
an additional parameter.

This makes the code in tcindex_alloc_perfect_hash()
prettier.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow enabling VEPA mode on the HCA's port in legacy devlink mode.

Example:
bridge link set dev ens1f0 hwmode vepa
will turn on VEPA mode on the netdev ens1f0.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In Virtual Ethernet Port Aggregator (VEPA) mode, the packet skips
the system internal virtual switch and forwards to external network
switch. In Mellanox HCA case, the virtual switch is the HCA's Eswitch.

To support this, an new FDB flow table are created with level 0 and
linked to the existing FDB flow table in legacy mode. By default,
VEPA is turned off and this FDB flow table is empty. When VEPA is
turned on, two rules are created. One rule to forward on uplink vport
traffic to the legacy FDB. The other rule forward all other traffic
to uplink vport.

Other design alternatives were not chosen as explained below:
1. Create a forward rule in ACL flow table (most efficient design).
This approach is the not chosen because firmware does not support
forward rule to uplink vport (0xffff) for ACL flow table.
2. Add additional source port criteria in all the FDB rules to make the
FDB rules to be received rules only. This approach is not chosen because
it is not efficient as there can many rules in the FDB and VEPA mode
cannot be controlled per vport.
3. Add a highest prioirty flow group in the existing legacy FDB Flow
Table instead of a new flow table. This approoach does not work because the
new flow group has the same match criteria as the promiscuous flow group
and mlx5_add_flow_rules does not allow specifying flow group.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

If reporter is ERR_PTR or NULL, error code shall be returned. At all other
cases it shall return success. Fix that.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In case of lost interrupt recover, we shall return success. Fix that.

Fixes: 7d91126b ("net/mlx5e: Add tx timeout support for mlx5e tx reporter")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When TX reporter was introduced, it took ownership over TX timeout error
handling. this introduced a regression in case TX reporter is not valid
(NET_DEVLINK is not set, or devlink_health_reporter_create failure).

Fix mlx5e_tx_reporter_timeout function so it can be called at all times.

In addition, remove a warning print that indicates that a TX timeout won't
be handled in case of no valid TX reporter.

Fixes: 7d91126b ("net/mlx5e: Add tx timeout support for mlx5e tx reporter")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Print warning message in case of TX reporter creation failure, only if the
return value is ERR_PTR type. NULL pointer return indicates that
NET_DEVLINK is not set, and the warning print can be skipped.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bf ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.

Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).

Fixes: df2ef3bf ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.

Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.

As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently changing a PCMR field is done by setting the field in a
zeroed buffer, zeroing other unrelated fields.
Fix this behaviour by modifying only the required field after first
reading the current register values, as a pre-step towards using more
fields in PCMR register.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.1

Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.

wireless-drivers was merged due to dependency in mt76.

Major changes:

iwlwifi

* HE radiotap

* FTM (Fine Timing Measurement) initiator and responder implementation

* bump supported firmware API to 46

* VHT extended NSS support

* new PCI IDs for 9260 and 22000 series

ath10k

* change QMI interface to support the new (and backwards incompatible)
  interface from HL3.1 and used in recent HL2.0 branch firmware
  releases

* support WPA3 with WCN3990

* support for mac80211 airtime fairness based on transmit rate
  estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
  enable this

* report transmit airtime to mac80211 with firmwares having
  WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
  airtime fairness based on real transmit time (instead of just
  estimated from transmit rate)

* support Fine Timing Measurement (FTM) responder role

* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT

* switch to use SPDX license identifiers

ath

* add new country codes for US

brcmfmac

* support monitor frames with the hardware/ucode header

qtnfmac

* enable WPA3 SAE and OWE support

mt76

* beacon support for USB devices (mesh+ad-hoc only)

rtlwifi

* convert to use SPDX license identifiers

libertas_tf

* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Maxim Mikityanskiy says:

====================
AF_PACKET transport_offset fix

This patch series contains the implementation of the RFC that was posted
on this mailing list previously:
https://www.spinics.net/lists/netdev/msg541709.html

It fixes having incorrect skb->transport_header values in cases when
dissect fails. Having correct values set by the kernel fixes mlx5
operation and allows to remove some unnecessary code flows in mlx5.

v2 changes:

- Rebase against the fresh net-next.
- Don't return bool from skb_probe_transport_header (and don't rename
  the function).
- WARN_ON_ONCE and error path in case of GSO without the L4 header.
====================
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After AF_PACKET is fixed to calculate the transport header offset
correctly, trust the value set by the kernel. If the offset wasn't set,
it means there is no transport header in the packet.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_transport_offset() == 0 is not a special value. The only special
value is when skb->transport_header is ~0U, and it's checked by
skb_transport_header_was_set().
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

c72219b7 introduced tpacket_set_protocol that parses the Ethernet L2
header and sets skb->protocol if it's unset. It is no longer needed
since the introduction of packet_parse_headers. In case of SOCK_RAW and
unset skb->protocol, packet_parse_headers asks the driver to tell the
protocol number, and it's implemented for all Ethernet devices. As the
old function supported only Ethernet, no functionality is lost.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a socket was created with socket(AF_PACKET, SOCK_RAW, 0), the
protocol number is unavailable. Try to ask the driver to extract it from
the L2 header in order for skb_try_probe_transport_header to succeed.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>