- 19 Jul, 2023 1 commit
-
-
Dave Marchevsky authored
Structs bpf_rb_node and bpf_list_node are opaquely defined in uapi/linux/bpf.h, as BPF program writers are not expected to touch their fields - nor does the verifier allow them to do so. Currently these structs are simple wrappers around structs rb_node and list_head and linked_list / rbtree implementation just casts and passes to library functions for those data structures. Later patches in this series, though, will add an "owner" field to bpf_{rb,list}_node, such that they're not just wrapping an underlying node type. Moreover, the bpf linked_list and rbtree implementations will deal with these owner pointers directly in a few different places. To avoid having to do void *owner = (void*)bpf_list_node + sizeof(struct list_head) with opaque UAPI node types, add bpf_{list,rb}_node_kern struct definitions to internal headers and modify linked_list and rbtree to use the internal types where appropriate. Signed-off-by:Dave Marchevsky <davemarchevsky@fb.com> Link: https://lore.kernel.org/r/20230718083813.3416104-3-davemarchevsky@fb.comSigned-off-by:
Alexei Starovoitov <ast@kernel.org>
-
- 17 Jul, 2023 24 commits
-
-
David S. Miller authored
Luo Jie says: ==================== net: phy: at803x: support qca8081 1G version chip This patch series add supporting qca8081 1G version chip, the 1G version chip can be identified by the register mmd7.0x901d bit0. In addition, qca8081 does not support 1000BaseX mode and the sgmii fifo reset is added on the link changed, which assert the fifo on the link down, deassert the fifo on the link up. Changes in v1: * switch to use genphy_c45_pma_read_abilities. * remove the patch [remove 1000BaseX mode of qca8081]. * move the sgmii fifo reset to link_change_notify. Changes in v2: * split the qca8081 1G chip support patch. * improve the slave seed config, disable it if master preferred. Changes in v3: * fix the comments. * add the help function qca808x_has_fast_retrain_or_slave_seed. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Luo Jie authored
The qca8081 sgmii fifo needs to be reset on link down and released on the link up in case of any abnormal issue such as the packet blocked on the PHY. Signed-off-by:
Luo Jie <quic_luoj@quicinc.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Luo Jie authored
The fast retrain and slave seed configs are only applicable when the 2.5G ability is supported. Signed-off-by:
-
Luo Jie authored
The qca8081 1G chip version does not support 2.5 capability, which is distinguished from qca8081 2.5G chip according to the bit0 of register mmd7.0x901d, the 1G version chip also has the same PHY ID as the normal qca8081 2.5G chip. Signed-off-by:
-
Luo Jie authored
qca8081 is the single port PHY, the slave prefer mode is used by default. if the phy master perfer mode is configured, the slave seed configuration should not be enabled, since the slave seed enablement is for making PHY linked as slave mode easily. disable slave seed if the master mode is preferred. Signed-off-by:
-
Luo Jie authored
merge the seed enablement and seed value configuration into one function, since the random seed value is needed to be configured when the seed is enabled. Signed-off-by:
-
Luo Jie authored
qca8081 PHY supports to use genphy_c45_pma_read_abilities for getting the PHY features supported except for the autoneg ability but autoneg ability exists in MDIO_STAT1 instead of MMD7.1, add it manually after calling genphy_c45_pma_read_abilities. Signed-off-by:
-
David S. Miller authored
Vignesh Viswanathan says: ==================== net: qrtr: Few fixes in QRTR Add fixes in QRTR ns to change server and nodes radix tree to xarray to avoid a use-after-free while iterating through the server or nodes radix tree. Also fix the destination port value for IPCR control buffer on older targets. ==================== Signed-off-by: -
Vignesh Viswanathan authored
The destination port value in the IPCR control buffer on older targets is 0xFFFF. Handle the same by updating the dst_port to QRTR_PORT_CTRL. Signed-off-by:
Vignesh Viswanathan <quic_viswanat@quicinc.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Vignesh Viswanathan authored
There is a use after free scenario while iterating through the nodes radix tree despite the ns being a single threaded process. This can happen when the radix tree APIs are not synchronized with the rcu_read_lock() APIs. Convert the radix tree for nodes to xarray to take advantage of the built in rcu lock usage provided by xarray. Signed-off-by:
Chris Lew <quic_clew@quicinc.com> Signed-off-by:
-
Vignesh Viswanathan authored
There is a use after free scenario while iterating through the servers radix tree despite the ns being a single threaded process. This can happen when the radix tree APIs are not synchronized with the rcu_read_lock() APIs. Convert the radix tree for servers to xarray to take advantage of the built in rcu lock usage provided by xarray. Signed-off-by:
-
David S. Miller authored
Justin Chen says: ==================== Brcm ASP 2.0 Ethernet Controller Add support for the Broadcom ASP 2.0 Ethernet controller which is first introduced with 72165. ==================== Signed-off-by: -
Justin Chen authored
Add maintainers entry for ASP 2.0 Ethernet driver. Reviewed-by:
Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by:
Justin Chen <justin.chen@broadcom.com> Signed-off-by:
-
Florian Fainelli authored
74165 is a 16nm process SoC with a 10/100 integrated Ethernet PHY, utilize the recently defined 16nm EPHY macro to configure that PHY. Reviewed-by:
-
Justin Chen authored
Add mdio compat string for ASP 2.0 ethernet driver. Reviewed-by:
-
Justin Chen authored
Add support for ethernet driver specific stats. Signed-off-by:
-
Justin Chen authored
Add support for eth_mac_stats, rmon_stats, and eth_ctrl_stats. Signed-off-by:
-
Justin Chen authored
Add support for eee mode. Signed-off-by:
-
Justin Chen authored
Add support for wake on network filters. The max match is 256 bytes. Signed-off-by:
-
Justin Chen authored
Add support for Wake-On-Lan magic packet and magic packet with password. Signed-off-by:
-
Justin Chen authored
Add support for the Broadcom ASP 2.0 Ethernet controller which is first introduced with 72165. This controller features two distinct Ethernet ports that can be independently operated. Reviewed-by:
-
Florian Fainelli authored
Add a binding document for the Broadcom ASP 2.0 Ethernet controller. Reviewed-by:
Conor Dooley <conor.dooley@microchip.com> Signed-off-by:
-
Justin Chen authored
The ASP 2.0 Ethernet controller uses a brcm unimac. Reviewed-by:
-
Csókás Bence authored
Rename local `struct fec_enet_private *adapter` to `fep` in `fec_ptp_gettime()` to match the rest of the driver Signed-off-by:
Csókás Bence <csokas.bence@prolan.hu> Reviewed-by:
-
- 14 Jul, 2023 15 commits
-
-
Jesper Dangaard Brouer authored
Spotted this trivial spell mistake while casually reading the google GVE driver code. Signed-off-by:
Jesper Dangaard Brouer <hawk@kernel.org> Signed-off-by:
-
David S. Miller authored
Petr Machata says: ==================== mlxsw: Manage RIF across PVID changes The mlxsw driver currently makes the assumption that the user applies configuration in a bottom-up manner. Thus netdevices need to be added to the bridge before IP addresses are configured on that bridge or SVI added on top of it. Enslaving a netdevice to another netdevice that already has uppers is in fact forbidden by mlxsw for this reason. Despite this safety, it is rather easy to get into situations where the offloaded configuration is just plain wrong. As an example, take a front panel port, configure an IP address: it gets a RIF. Now enslave the port to the bridge, and the RIF is gone. Remove the port from the bridge again, but the RIF never comes back. There is a number of similar situations, where changing the configuration there and back utterly breaks the offload. The situation is going to be made better by implementing a range of replays and post-hoc offloads. In this patch set, address the ordering issues related to creation of bridge RIFs. Currently, mlxsw has several shortcomings with regards to RIF handling due to PVID changes: - In order to cause RIF for a bridge device to be created, the user is expected first to set PVID, then to add an IP address. The reverse ordering is disallowed, which is not very user-friendly. - When such bridge gets a VLAN upper whose VID was the same as the existing PVID, and this VLAN netdevice gets an IP address, a RIF is created for this netdevice. The new RIF is then assigned to the 802.1Q FID for the given VID. This results in a working configuration. However, then, when the VLAN netdevice is removed again, the RIF for the bridge itself is never reassociated to the PVID. - PVID cannot be changed once the bridge has uppers. Presumably this is because the driver does not manage RIFs properly in face of PVID changes. However, as the previous point shows, it is still possible to get into invalid configurations. This patch set addresses these issues and relaxes some of the ordering requirements that mlxsw had. The patch set proceeds as follows: - In patch #1, pass extack to mlxsw_sp_br_ban_rif_pvid_change() - To relax ordering between setting PVID and adding an IP address to a bridge, mlxsw must be able to request that a RIF is created with a given VLAN ID, instead of trying to deduce it from the current netdevice settings, which do not reflect the user-requested values yet. This is done in patches #2 and #3. - Similarly, mlxsw_sp_inetaddr_bridge_event() will need to make decisions based on the user-requested value of PVID, not the current value. Thus in patches #4 and #5, add a new argument which carries the requested PVID value. - Finally in patch #6 relax the ban on PVID changes when a bridge has uppers. Instead, add the logic necessary for creation of a RIF as a result of PVID change. - Relevant selftests are presented afterwards. In patch #7 a preparatory helper is added to lib.sh. Patches #8, #9, #10 and #11 include selftests themselves. ==================== Signed-off-by: -
Petr Machata authored
This tests whether addition and deletion of a VLAN upper that coincides with the current PVID setting throws off forwarding. This selftests is specifically geared towards offloading drivers. In particular, mlxsw used to fail this selftest, and an earlier patch in this patchset fixes the issue. However, there's nothing HW-specific in the test itself (it absolutely is supposed to pass on SW datapath), and therefore it is put into the generic forwarding directory. Signed-off-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
Danielle Ratson <danieller@nvidia.com> Signed-off-by:
-
Petr Machata authored
This tests whether changes to PVID that coincide with an existing VLAN upper throw off forwarding. This selftests is specifically geared towards offloading drivers, but since there's nothing HW-specific in the test itself (it absolutely is supposed to pass on SW datapath), it is put into the generic forwarding directory. Signed-off-by:
-
Petr Machata authored
Add an alternative path involving VLAN 777 instead of the current 555. Then add tests that verify that marking 777 as PVID makes the 555 path not work, and the 777 path work. Signed-off-by:
-
Petr Machata authored
This test relies on PVID being configured on the bridge itself. Thus when it is deconfigured, the system should lose the ability to forward traffic. Later when it is added again, the ability to forward traffic should be regained. Add tests to exercise these configuration changes and verify results. Signed-off-by:
-
Petr Machata authored
Add two helpers to run a ping test that succeeds when the pings themselves fail. Signed-off-by:
-
Petr Machata authored
Currently, mlxsw has several shortcomings with regards to RIF handling due to PVID changes: - In order to cause RIF for a bridge device to be created, the user is expected first to set PVID, then to add an IP address. The reverse ordering is disallowed, which is not very user-friendly. - When such bridge gets a VLAN upper whose VID was the same as the existing PVID, and this VLAN netdevice gets an IP address, a RIF is created for this netdevice. The new RIF is then assigned to the 802.1Q FID for the given VID. This results in a working configuration. However, then, when the VLAN netdevice is removed again, the RIF for the bridge itself is never reassociated to the VLAN. - PVID cannot be changed once the bridge has uppers. Presumably this is because the driver does not manage RIFs properly in face of PVID changes. However, as the previous point shows, it is still possible to get into invalid configurations. In this patch, add the logic necessary for creation of a RIF as a result of PVID change. Moreover, when a VLAN upper is created whose VID matches lower PVID, do not create RIF for this netdevice. These changes obviate the need for ordering of IP address additions and PVID configuration, so stop forbidding addition of an IP address to a PVID-less bridge. Instead, bail out quietly. Also stop preventing PVID changes when the bridge has uppers. Signed-off-by:
-
Petr Machata authored
For purposes of replay, mlxsw_sp_inetaddr_bridge_event() will need to make decisions based on the proposed value of PVID. Querying PVID reveals the current settings, not the in-flight values that the user requested and that the notifiers are acting upon. Add a parameter, lower_pvid, which carries the proposed PVID of the lower bridge, or -1 if the lower is not a bridge. Signed-off-by:
-
Petr Machata authored
The bridge branch of the dispatch in this function is going to get more code and will need curly braces. Per the doctrine, that means the whole if-else chain should get them. Signed-off-by:
-
Petr Machata authored
Currently, when an IP address is added to a bridge that has no PVID, the operation is rejected. An IP address addition is interpreted as a request to create a RIF for the bridge device, but without a PVID there is no VLAN for which the RIF should be created. Thus the correct way to create a RIF for a bridge as a user is to first add a PVID, and then add the IP address. Ideally this ordering requirement would not exist. RIF would be created either because an IP address is added, or because a PVID is added, depending on which comes last. For that, the switchdev code (which notices the PVID change request) must be able to request that a RIF is created with a given VLAN ID, because at the time that the PVID notification is distributed, the PVID setting is not yet visible for querying. Therefore when creating a VLAN-based RIF, use mlxsw_sp_rif_params.vid to communicate the VID, and do not determine it ad-hoc in the fid_get callback. Signed-off-by:
-
Petr Machata authored
The fid_get callback is called to allocate a FID for the newly-created RIF. In a following patch, the fid_get implementation for VLANs will be modified to take the VLAN ID from the parameters instead of deducing it from the netdevice. To that end, propagate the RIF parameters to the fid_get callback. Signed-off-by:
-
Petr Machata authored
Currently the reason for rejection of PVID manipulation is dumped to syslog, and a generic -EBUSY is returned to the userspace. But switchdev_handle_port_obj_add(), through which we get to mlxsw_sp_port_vlans_add(), handles extack just fine, and we can pass the message this way. This improves visibility into reasons why the request to change PVID was rejected. Before the change: # bridge vlan add dev br vid 2 self pvid untagged RTNETLINK answers: Device or resource busy (plus a syslog line) After the change: # bridge vlan add dev br vid 2 self pvid untagged Error: mlxsw_spectrum: Can't change PVID, it's used by router interface. Note that this particular error message is going away in the following patches. However the ability to pass error messages through extack will be useful more broadly for communicating in particular reasons why a RIF failed to be created. Signed-off-by:
-
David S. Miller authored
Sabrina Dubroca says: ==================== net: add MACsec offload selftests Patch 1 adds MACsec offload to netdevsim (unchanged from v2). Patch 2 adds a corresponding selftest to the rtnetlink testsuite. ==================== Signed-off-by: -
Sabrina Dubroca authored
Like the IPsec offload test, this requires netdevsim. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
