- 08 Jan, 2021 28 commits
-
-
James Smart authored
While testing recent discovery node rework, several items were seen that could be done better with respect to the new trace event logic. 1) in the following msg: kernel: lpfc 0000:44:00.0: start 35 end 35 cnt 0 If cnt is zero in the 1st message, there is no reason to display the 1st message, which is just giving start/end positioning. Fix by not displaying message if cnt is 0. 2) If the driver is loaded with module log verbosity off, and later a single NPIV host instance verbosity is enabled via sysfs, it enables messages on all instances. This is due to the trace log verbosity checks (lpfc_dmp_dbg) looking at the phba only. It should look at the phba and the vport. Fix by enabling a check on both phba and vport. 3) in the following messages: 2904 Firmware Dump Image Present on Adapter 2887 Reset Needed: Attempting Port Recovery... These messages are not necessary for the trace event log, which is primarily for discovery. Fix by changing log level on these 2 messages to LOG_SLI. Link: https://lore.kernel.org/r/20210104180240.46824-15-jsmart2021@gmail.comCo-developed-by:Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
James Smart authored
Several errors have occurred where the adapter stops or fails but does not raise the register values for the driver to detect failure. Thus driver is unaware of the failure. The failure typically results in I/O timeouts, the I/O timeout handler failing (after several seconds), and the error handler escalating recovery policy and resulting in more errors. Eventually, the driver is in a position where things have spiraled and it can't do recovery because other recovery ops are still outstanding and it becomes unusable. Resolve the situation by having the I/O timeout handler (actually a els, SCSI I/O, NVMe ls, or NVMe I/O timeout), in addition to aborting the I/O, perform a mailbox command and look for a response from the hardware. If the mailbox command fails, it will mark the adapter offline and then invoke the adapter reset handler to clean up. The new I/O timeout test will be limited to a test every 5s. If there are multiple I/O timeouts concurrently, only the 1st I/O timeout will generate the mailbox command. Further testing will only occur once a timeout occurs after a 5s delay from the last mailbox command has expired. Link: https://lore.kernel.org/r/20210104180240.46824-14-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
When lpfc is running in NVMET mode and supports the NVME-1 addendum changes, a LIP on a bound NVME Initiator or lipping the lpfc NVMET's link resulted in an Oops in lpfc_nvmet_host_release. The fix requires lpfc NVMET to maintain an additional reference on any node structure that acts as the hosthandle for the NVMET transport. This reference get is a one-time addition, is taken prior to the upcall of an unsolicited LS_REQ, and is released when the NVMET transport releases the hosthandle during the host_release downcall. Link: https://lore.kernel.org/r/20210104180240.46824-13-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
When with testing with large numbers of npiv vports and link bounces, the driver is flooding the messages file, even with log_verbose = 0. The new LOG_TRACE_EVENT messages are still generating events to the messages files. Fix by converting the vport create msg from LOG_TRACE_EVENT to LOG_VPORT. Link: https://lore.kernel.org/r/20210104180240.46824-12-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
If a mailbox command times out, the SLI port is deemed in error and the port is reset. The HBA cleanup is not returning I/Os to the NVMe layer before the port is unregistered. This is due to the HBA being marked offline (!SLI_ACTIVE) and cleanup being done by the mailbox timeout handler rather than an general adapter reset routine. The mailbox timeout handler mailbox handler only cleaned up SCSI I/Os. Fix by reworking the mailbox handler to: - After handling the mailbox error, detect the board is already in failure (may be due to another error), and leave cleanup to the other handler. - If the mailbox command timeout is initial detector of the port error, continue with the board cleanup and marking the adapter offline (!SLI_ACTIVE). Remove the SCSI-only I/O cleanup routine. The generic reset adapter routine that is subsequently invoked, will clean up the I/Os. - Have the reset adapter routine flush all NVMe and SCSI I/Os if the adapter has been marked failed (!SLI_ACTIVE). - Rework the NVMe I/O terminate routine to take a status code to fail the I/O with and update so that cleaned up I/O calls the wqe completion routine. Currently it is bypassing the wqe cleanup and calling the NVMe I/O completion directly. The wqe completion routine will take care of data structure and node cleanup then call the NVMe I/O completion handler. Link: https://lore.kernel.org/r/20210104180240.46824-11-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
Target reset is failed by the target as an invalid command. The Target Reset TMF has been obsoleted in T10 for a while, but continues to be used. On (newer) devices, the TMF is rejected causing the reset handler to escalate to adapter resets. Fix by having Target Reset TMF rejections be translated into a LOGO and re-PLOGI with the target device. This provides the same semantic action (although, if the device also supports nvme traffic, it will terminate nvme traffic as well - but it's still recoverable). Link: https://lore.kernel.org/r/20210104180240.46824-10-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
A successful task mgmt command is logging errors, making it look like problems were encountered. This is due to log messages for the device/target and bus reset handlers having the LOG_TRACE_EVENT flag set. Fix by adjusting the event flag such that the call to the logging routine only receives a LOG_TRACE_EVENT if a prior call actually failed. Link: https://lore.kernel.org/r/20210104180240.46824-9-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
In the lpfc offline routine, called for various reasons such as sysfs attribute, driver unload, or port error, the driver is calling __lpfc_cpuhp_remove() to destroy the hot plug data. If the offline routine is called while the driver is in the process of being unloaded, a request using lpfc_cpuhp_remove() is also made from lpfc_sli4_hba_unset(). The cpuhp elements are no longer valid when the second removal request is made. Fix by only calling the cpuhp removal once when the adapter is in the process of unloading. Link: https://lore.kernel.org/r/20210104180240.46824-8-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
If the port is configured for NVME and has any outstanding IOs when a FW reset is requesteed, outstanding I/Os are not properly cleaned up. This causes the fw download request to fail. Fix by clearing the LPFC_SLI_ACTIVE flag to signify the I/O must be manually flushed by the driver on port reset. Link: https://lore.kernel.org/r/20210104180240.46824-7-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
When lpfc generates a GEN_REQUEST wqe for the nvme LS (such as Create Association), the timeout is set to R_A_TOV without regard to the timeout value supplied by the nvme-fc transport. The driver should be setting the timeout to the value passed into the routine. Additionally the caller should be setting the timeout value to the value in the ls request set by the nvme transport. Instead, it unconditionally is setting it to a driver defined value. So the driver actually overrode the value twice. Fix by using the timeout provided to the routine, and for the caller, set the timeout to the ls request timeout value. Link: https://lore.kernel.org/r/20210104180240.46824-6-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
The driver's management of the fabric controller (aka pseudo-scsi initiator) node in SLI3 mode is causing this crash. The crash occurs because of a node reference imbalance that frees the fabric controller node while devloss is outstanding from the SCSI transport. This is triggered by an odd behavior where the switch reacts to a rejected RDP request with a PLOGI and nothing else, not even a LOGO. The driver ACKS the PLOGI and after successfully registering the RPI, incorrectly registers the fabric controller node because it has the NLP_FC4_FCP flag still set from the fabric controller PRLI. If a LIP is issued, the driver attempts to cleanup on Link Up and ends up executing too many puts. Fix by detecting the fabric node type and clearing out the nodes internal flags that triggered a SCSI transport registration and subsequence dev_loss event. The driver cannot count on any persistence from fabric controller nodes. Link: https://lore.kernel.org/r/20210104180240.46824-5-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
Testing with target ports coming and going, the driver eventually reached a state where it no longer discovered the target. When the driver has issued a PRLI and receives a PRLI from the target, it is not properly updating the node's initiator/target role flags. Thus, when a subsequent RSCN is received for a target loss, the driver mis-identifies the target as an initiator and does not initiate LUN scanning. Fix by always refreshing the ndlp with the latest PRLI state information whenever a PRLI is processed. Also clear the ndlp flags when processing a PLOGI so that there is no carry over through a re-login. Link: https://lore.kernel.org/r/20210104180240.46824-4-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
A very long time ago, there was a feature: auto sli mode. It gave the user the ability to auto select the SLI mode (SLI2 or SLI3) to run the port in, or even force SLI2 mode if configured. Because of the convoluted logic, the CONFIG_PORT mbox command ends up being called 2 or 3 times. It should have been called only once. Additionally, the driver no longer supports SLI-2, so only SLI-3 mode should be allowed. The following changes were made: - Force module parameter to SLI3 only. - Rip out redundant CONFIG_PORT mbox commands. - Force CONFIG_PORT mbox command to be in beginning of enable ISR routine. - Added changes for offline to online behavior Link: https://lore.kernel.org/r/20210104180240.46824-3-jsmart2021@gmail.comCo-developed-by:
-
James Smart authored
Under some pt2pt situations, the other end of the link may issue a LOGO after successfully completing PLOGI and assigning addresses to the port. Thus the driver may attempt a new PLOGI to re-create the login, but the LOGO handling cleared the address back to 0. Once this happens, the other end, which may be address 0, gets all confused and this cannot be resolved without an administrative action to bounce the link. Fix by assuming that address assignment only occurs on the 1st PLOGI after link up, and regardless of login state, the address assignment sticks. The FC standards aren't particularly clear in this situation (it only describes initial PLOGI), but there is nothing that contradicts this and behaviors on the devices tested appears to conform to the understanding. Thus, don't reset the port address to 0 as part of LOGO handling. Port addresses will only reset on link down. Link: https://lore.kernel.org/r/20210104180240.46824-2-jsmart2021@gmail.comCo-developed-by:
-
John Garry authored
Now that the driver always uses managed interrupts, delete auto_affine_msi_experimental module param. Link: https://lore.kernel.org/r/1609763622-34119-2-git-send-email-john.garry@huawei.comSigned-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
-
Bean Huo authored
sprintf and snprintf may cause output defect in sysfs content, it is better to use new added sysfs_emit function which knows the size of the temporary buffer. Link: https://lore.kernel.org/r/20210106211541.23039-1-huobean@gmail.comSuggested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Reviewed-by:
Can Guo <cang@codeaurora.org> Signed-off-by:
Bean Huo <beanhuo@micron.com> Signed-off-by:
-
Randy Dunlap authored
Use consistent and expected indentation for all Kconfig text. Link: https://lore.kernel.org/r/20210106205554.18082-1-rdunlap@infradead.org Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Avri Altman <avri.altman@wdc.com> Cc: linux-scsi@vger.kernel.org Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Reviewed-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
-
Tyrel Datwyler authored
The driver's queuecommand routine is still wrapped to hold the host lock for the duration of the call. This will become problematic when moving to multiple queues due to the lock contention preventing asynchronous submissions to mulitple queues. There is no real legitimate reason to hold the host lock, and previous patches have insured proper protection of moving ibmvfc_event objects between free and sent lists. Link: https://lore.kernel.org/r/20210106201835.1053593-6-tyreld@linux.ibm.comReviewed-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
Tyrel Datwyler <tyreld@linux.ibm.com> Signed-off-by:
-
Tyrel Datwyler authored
Drain the command queue and place all commands on a completion list. Perform command completion on that list outside the host/queue locks. Further, move purged command compeletions outside the host_lock as well. Link: https://lore.kernel.org/r/20210106201835.1053593-5-tyreld@linux.ibm.comReviewed-by:
-
Tyrel Datwyler authored
Define per-queue locks for protecting queue state and event pool sent/free lists. The evt list lock is initially redundant but it allows the driver to be modified in the follow-up patches to relax the queue locking around submissions and completions. Link: https://lore.kernel.org/r/20210106201835.1053593-4-tyreld@linux.ibm.comReviewed-by:
-
Tyrel Datwyler authored
There is currently a single command event pool per host. In anticipation of providing multiple queues add a per-queue event pool definition and reimplement the existing CRQ to use its queue defined event pool for command submission and completion. Link: https://lore.kernel.org/r/20210106201835.1053593-3-tyreld@linux.ibm.comReviewed-by:
-
Tyrel Datwyler authored
The primary and async CRQs are nearly identical outside of the format and length of each message entry in the dma mapped page that represents the queue data. These queues can be represented with a generic queue structure that uses a union to differentiate between message format of the mapped page. This structure will further be leveraged in a followup patcheset that introduces Sub-CRQs. Link: https://lore.kernel.org/r/20210106201835.1053593-2-tyreld@linux.ibm.comReviewed-by:
-
Bean Huo authored
Transaction Specific Fields (TSF) in the UPIU package could be CDB (SCSI/UFS Command Descriptor Block), OSF (Opcode Specific Field), and TM I/O parameter (Task Management Input/Output Parameter). But, currently, we take all of these as CDB in the UPIU trace. Thus makes user confuse among CDB, OSF, and TM message. So fix it with this patch. Link: https://lore.kernel.org/r/20210105113446.16027-7-huobean@gmail.comAcked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Bean Huo authored
Distinguish between TM request UPIU and response UPIU in TM UPIU trace, for the TM response, let TM UPIU trace print its TM response UPIU. Link: https://lore.kernel.org/r/20210105113446.16027-6-huobean@gmail.comAcked-by:
-
Bean Huo authored
Currently, in the query completion trace print, since we use hba->lrb[tag].ucd_req_ptr and didn't differentiate UPIU between request and response, thus header and transaction-specific field in UPIU printed by query trace are identical. This is not very practical. As below: query_send: HDR:16 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 00 00 00 00 00 query_complete: HDR:16 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 00 00 00 00 00 For the failure analysis, we want to understand the real response reported by the UFS device, however, the current query trace tells us nothing. After this patch, the query trace on the query_send, and the above a pair of query_send and query_complete will be: query_send: HDR:16 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 00 00 00 00 00 ufshcd_upiu: HDR:36 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 01 00 00 00 00 Link: https://lore.kernel.org/r/20210105113446.16027-5-huobean@gmail.comAcked-by:
-
Bean Huo authored
Don't call trace_ufshcd_upiu() in case ufshba_upiu trace poit is not enabled. Link: https://lore.kernel.org/r/20210105113446.16027-4-huobean@gmail.comAcked-by:
-
Bean Huo authored
__print_symbolic() is designed for exporting the print formatting table to userspace and allows parsing tool, such as trace-cmd and perf, to analyze trace log according to this print formatting table, meanwhile, by using __print_symbolic()s, save space in the trace ring buffer. original print format: print fmt: "%s: %s: HDR:%s, CDB:%s", __get_str(str), __get_str(dev_name), __print_hex(REC->hdr, sizeof(REC->hdr)), __print_hex(REC->tsf, sizeof(REC->tsf)) after this change: print fmt: "%s: %s: HDR:%s, CDB:%s", print_symbolic(REC->str_t, {0, "send"}, {1, "complete"}, {2, "dev_complete"}, {3, "query_send"}, {4, "query_complete"}, {5, "query_complete_err"}, {6, "tm_send"}, {7, "tm_complete"}, {8, "tm_complete_err"}), __get_str(dev_name), __print_hex(REC->hdr, sizeof(REC->hdr)), __print_hex(REC->tsf, sizeof(REC->tsf)) Note: This patch just converts current __get_str(str) to __print_symbolic(), the original tracing log will not be affected by this change, so it doesn't break what current parsers expect. Link: https://lore.kernel.org/r/20210105113446.16027-3-huobean@gmail.comAcked-by: -
Bean Huo authored
Current EM macro definition, we use stringize operator '#', which turns the argument it precedes into a quoted string. Thus requires the symbol of __print_symbolic() should be the string corresponding to the name of the enum. However, we have other cases, the symbol and enum name are not the same, we can redefine EM/EMe, but there will introduce some redundant codes. This patch is to remove this restriction, let others reuse the current EM/EMe definition. Link: https://lore.kernel.org/r/20210105113446.16027-2-huobean@gmail.comAcked-by:
-
- 06 Jan, 2021 3 commits
-
-
Kiwoong Kim authored
Set optimized values for the following timeouts: - FC0_PROTECTION_TIMER - TC0_REPLAY_TIMER - AFC0_REQUEST_TIMER Exynos doesn't yet use traffic class #1. Link: https://lore.kernel.org/r/a0ff44f665a4f31d2f945fd71de03571204c576c.1608513782.git.kwmad.kim@samsung.comSigned-off-by:
Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by:
-
Kiwoong Kim authored
The UniPro specification states that attribute IDs of the following parameters are vendor-specific so some SoCs could have no regions at the defined addresses: - DME_LocalFC0ProtectionTimeOutVal - DME_LocalTC0ReplayTimeOutVal - DME_LocalAFC0ReqTimeOutVal In addition, the following parameters should be set considering the compatibility between host and device. - PA_PWRMODEUSERDATA0 - PA_PWRMODEUSERDATA1 - PA_PWRMODEUSERDATA2 - PA_PWRMODEUSERDATA3 - PA_PWRMODEUSERDATA4 - PA_PWRMODEUSERDATA5 Introduce a quirk to allow vendor drivers to override the UniPro defaults. Link: https://lore.kernel.org/r/1fedd3dea0ccc980913a5995a10510d86a5b01b9.1608513782.git.kwmad.kim@samsung.comAcked-by:
-
Stanley Chu authored
Flush during hibern8 is sufficient on MediaTek platforms, thus enable UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL to skip enabling fWriteBoosterBufferFlush during WriteBooster initialization. Link: https://lore.kernel.org/r/20201222072928.32328-1-stanley.chu@mediatek.comReviewed-by:
Stanley Chu <stanley.chu@mediatek.com> Signed-off-by:
-
- 03 Jan, 2021 1 commit
-
-
Linus Torvalds authored
-
- 02 Jan, 2021 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linuxLinus Torvalds authored
Pull s390 cleanups from Vasily Gorbik: "Update defconfigs and sort config select list" * tag 's390-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/Kconfig: sort config S390 select list once again s390: update defconfigs
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management fixes from Rafael Wysocki: "These fix a crash in intel_pstate during resume from suspend-to-RAM that may occur after recent changes and two resource leaks in error paths in the operating performance points (OPP) framework, add a new C-states table to intel_idle and update the cpuidle MAINTAINERS entry to cover the governors too. Specifics: - Fix recently introduced crash in the intel_pstate driver that occurs if scale-invariance is disabled during resume from suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR values made by the platform firmware (Rafael Wysocki). - Fix a memory leak and add a missing clk_put() in error paths in the OPP framework (Quanyang Wang, Viresh Kumar). - Add new C-states table for SnowRidge processors to the intel_idle driver (Artem Bityutskiy). - Update the MAINTAINERS entry for cpuidle to make it clear that the governors are covered by it too (Lukas Bulwahn)" * tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: intel_idle: add SnowRidge C-state table cpufreq: intel_pstate: Fix fast-switch fallback path opp: Call the missing clk_put() on error opp: fix memory leak in _allocate_opp_table MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK -
Rafael J. Wysocki authored
* pm-cpufreq: cpufreq: intel_pstate: Fix fast-switch fallback path * pm-cpuidle: intel_idle: add SnowRidge C-state table MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK
-
- 01 Jan, 2021 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fixes from James Bottomley: "This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi). The big core two fixes are for power management ("block: Do not accept any requests while suspended" and "block: Fix a race in the runtime power management code") which finally sorts out the resume problems we've occasionally been having. To make the resume fix, there are seven necessary precursors which effectively renames REQ_PREEMPT to REQ_PM, so every "special" request in block is automatically a power management exempt one. All of the non-PM preempt cases are removed except for the one in the SCSI Parallel Interface (spi) domain validation which is a genuine case where we have to run requests at high priority to validate the bus so this becomes an autopm get/put protected request" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits) scsi: cxgb4i: Fix TLS dependency scsi: ufs: Un-inline ufshcd_vops_device_reset function scsi: ufs: Re-enable WriteBooster after device reset scsi: ufs-mediatek: Use correct path to fix compile error scsi: mpt3sas: Signedness bug in _base_get_diag_triggers() scsi: block: Do not accept any requests while suspended scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE scsi: scsi_transport_spi: Set RQF_PM for domain validation commands scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT scsi: ide: Do not set the RQF_PREEMPT flag for sense requests scsi: block: Introduce BLK_MQ_REQ_PM scsi: block: Fix a race in the runtime power management code scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff() scsi: ufs-pci: Fix restore from S4 for Intel controllers scsi: ufs-mediatek: Keep VCC always-on for specific devices scsi: ufs: Allow regulators being always-on scsi: ufs: Clear UAC for RPMB after ufshcd resets ... -
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: "Two minor block fixes from this last week that should go into 5.11: - Add missing NOWAIT debugfs definition (Andres) - Fix kerneldoc warning introduced this merge window (Randy)" * tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block: block: add debugfs stanza for QUEUE_FLAG_NOWAIT fs: block_dev.c: fix kernel-doc warnings from struct block_device changes
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring fixes from Jens Axboe: "A few fixes that should go into 5.11, all marked for stable as well: - Fix issue around identity COW'ing and users that share a ring across processes - Fix a hang associated with unregistering fixed files (Pavel) - Move the 'process is exiting' cancelation a bit earlier, so task_works aren't affected by it (Pavel)" * tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block: kernel/io_uring: cancel io_uring before task works io_uring: fix io_sqe_files_unregister() hangs io_uring: add a helper for setting a ref node io_uring: don't assume mm is constant across submits -
Linus Torvalds authored
Commit 436e980e ("kbuild: don't hardcode depmod path") stopped hard-coding the path of depmod, but in the process caused trouble for distributions that had that /sbin location, but didn't have it in the PATH (generally because /sbin is limited to the super-user path). Work around it for now by just adding /sbin to the end of PATH in the depmod.sh script. Reported-and-tested-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- 31 Dec, 2020 1 commit
-
-
Pavel Begunkov authored
For cancelling io_uring requests it needs either to be able to run currently enqueued task_works or having it shut down by that moment. Otherwise io_uring_cancel_files() may be waiting for requests that won't ever complete. Go with the first way and do cancellations before setting PF_EXITING and so before putting the task_work infrastructure into a transition state where task_work_run() would better not be called. Cc: stable@vger.kernel.org # 5.5+ Signed-off-by:
Pavel Begunkov <asml.silence@gmail.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
