- 08 Feb, 2013 40 commits
-
-
Piotr Haber authored
Locking host access in trap info processing is not needed as bus access functions do it on their own. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
Piotr Haber <phaber@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Piotr Haber authored
Make sure backplane clocks are on while reading crash data. Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
-
Piotr Haber authored
fix wrong locking in crash info processing Reviewed-by:
-
Hante Meuleman authored
When unloading it is possible that drvr is not null, but iflist[0] is. So check iflist[0] pointer before using it. Reviewed-by:
-
Hante Meuleman authored
Upon receiving an IF event from the firmware the interface was created and stored on a list using the interface index. With upcoming P2P feature the firmware will send a IF event in which two interfaces have the same interface index. To uniquely locate them on the list the bss index is now used. Reviewed-by:
-
Joe Perches authored
alloc failures already get standardized OOM messages and a dump_stack. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Tim Gardner authored
Dynamically allocate the probe response template which avoids potential stack corruption. Observed with smatch: drivers/net/wireless/brcm80211/brcmsmac/main.c:7412 brcms_c_bss_update_probe_resp() warn: 'prb_resp' puts 512 bytes on stack Cc: Brett Rudley <brudley@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Seth Forshee <seth.forshee@canonical.com> Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list@broadcom.com Cc: netdev@vger.kernel.org Signed-off-by:
Tim Gardner <tim.gardner@canonical.com> Acked-by:
-
Tim Gardner authored
DOT11_MIN_BEACON_PERIOD and DOT11_MAX_BEACON_PERIOD are superfluous. The only invalid beacon period is 0. Comparing a 16 bit quantity to 0xffff also causes a compile warning: drivers/net/wireless/brcm80211/brcmsmac/main.c:5560 brcms_c_set_beacon_period() warn: impossible condition '(period > 65535) => (0-65535 > 65535)' Observed from smatch analysis. Cc: Brett Rudley <brudley@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Hante Meuleman <meuleman@broadcom.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com> Cc: Seth Forshee <seth.forshee@canonical.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: linux-wireless@vger.kernel.org Cc: brcm80211-dev-list@broadcom.com Cc: netdev@vger.kernel.org Signed-off-by:
-
Jiri Slaby authored
It can, if invalid argument given, return a negative value. In that case we would access arrays out-of-bounds and such. Check the value and yell loudly if that happened as it would be a bug in the implementation. (Instead of silently corrupting memory.) Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Signed-off-by:
-
Larry Finger authored
When the new_id entry in /sysfs is used for a foreign USB device, rtlwifi BUGS with a NULL pointer dereference because the per-driver configuration data is not available. The probe function has been restructured as suggested by Ben Hutchings <bhutchings@solarflare.com>. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
-
Arend van Spriel authored
The bcm43236 device showed having an issue connection to an AP without security when auth_type was set to automatic. For this particular device a workaround is made by selecting open-system. This problem does not occur when using wpa_supplicant as it will not use auth type automatic. Reviewed-by:
-
Arend van Spriel authored
Added function to obtain chip information for chip specific code. Reviewed-by:
-
Arend van Spriel authored
Extend the bus interface with chip identifier and revision. This will be used when certain devices need special handling in the driver. Reviewed-by:
-
Hante Meuleman authored
Simplify code by using single function for converting channel to chanspec. No need to set 40MHz flags, as they are not needed for correct working in FW. Reviewed-by:
-
Hante Meuleman authored
Clean up function, removing some unnecessary code and initialisation. Reviewed-by:
-
Hante Meuleman authored
When supporting multiple netdevs it is usefull to log idx in netdev related functions. This will be used for features like P2P. Reviewed-by:
-
Hante Meuleman authored
Statistics were tracked by bus driver while it is to be tracked per ifp/netdev. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Pending 8021x frames were tracked per dongle. This should be done per ifp. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
At netdev up the mac address from drvr is copied to netdev mac address. This is incorrect and mac address was already set by brcmf_net_attach by copying it from ifp. Reviewed-by:
-
Hante Meuleman authored
The tracking of up/down status in bus interface is unnecessary. Reviewed-by:
-
Tomasz Guszkowski authored
Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The device was tested in managed mode with no security, WEP 128 bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum: 7d676323ac60d6e1a3b6d61e8c528248). It works. Signed-off-by:
Tomasz Guszkowski <tsg@o2.pl> Cc: <stable@vger.kernel.org> Acked-By:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Jonas Gorski authored
Add PCI deviceIDs for single band versions of 88W8366, found e.g. in simultaneous dual band routers based on kirkwood. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> Signed-off-by:
-
Cong Ding authored
The use of variable packet_beacon might be uninitialized in the two files, which is same as this patch: https://patchwork.kernel.org/patch/2006711/Signed-off-by:
Cong Ding <dinggnu@gmail.com> Signed-off-by:
-
Xose Vazquez Perez authored
Info coming from Sweex Windows driver and wikidevi.com 0x177f,0x0163 Sweex LW163 RT3370 1x1, int. antenna 0x177f,0x0164 Sweex LW164 RT8070 1x1, Nano dongle 0x177f,0x0165 Sweex LW165 RT3370 1x1, ext. antenna 0x177f,0x0324 Sweex LW324 RT3072 2x2 with 32Mb NOR flash, autoinstall Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by:
Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Dan Carpenter authored
If gb_len is less than 3 it would cause an integer underflow and possibly memory corruption in nfc_llcp_parse_gb_tlv(). I removed the old test for gb_len == 0. I also removed the test for ->remote_gb == NULL. It's not possible for ->remote_gb to be NULL and we have already dereferenced ->remote_gb_len so it's too late to test. The old test return -ENODEV but my test returns -EINVAL. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-nextJohn W. Linville authored
Samuel says: "This is the 2nd NFC pull request. With this one we have a new NFC driver for Inside Secure microread and a few pn533 fixes. Microread is an HCI based NFC IP and the driver we're pushing supports tags R/W, and NFC p2p. It's supported over the i2c and MEI busses." Signed-off-by: -
-
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextJohn W. Linville authored
Fixed-up drivers/net/wireless/iwlwifi/mvm/mac80211.c to change change IEEE80211_HW_NEED_DTIM_PERIOD to IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC as requested by Johannes Berg. -- JWL Signed-off-by: -
Thierry Escande authored
Remove unneeded bitwise OR operator on uninitialized sk_buff data Signed-off-by:
Thierry Escande <thierry.escande@linux.intel.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com>
-
Samuel Ortiz authored
On some peculiar worlds, microreads are found hidden behind MEIs and needs to be accessed through the ME bus. Signed-off-by: -
Luciano Coelho authored
In wl18xx, we use a new ACX command in order to set the remote supported rates, once we know it (ie. after association). The wl12xx firmware doesn't support changing the rates after the STA is started, so we need to use all supported rates. Commit 530abe19 (wlcore: add ACX_PEER_CAP command) broke that by using wlvif->rate_set when starting the STA role. Signed-off-by:
Luciano Coelho <coelho@ti.com>
-
Victor Goldenshtein authored
Add back-off settings to the wl18xx_mac_and_phy_params. We had an empty space where the new parameters are added, so this change doesn't affect backwards-compatibility with older firmwares. Update WL18XX_CONF_VERSION accordingly. Signed-off-by:
Victor Goldenshtein <victorg@ti.com> Signed-off-by:
-
Luciano Coelho authored
There's no need to hide the actual error that was reported when booting fails. For instance, on I/O error, we were returing -EINVALID, which doesn't make sense at all. Signed-off-by: -
Luciano Coelho authored
The platform data is used not only by wlcore-based drivers, but also by wl1251. Move it up in the directory hierarchy to reflect this. Additionally, make it truly optional. At the moment, disabling platform data while wl1251_sdio or wlcore_sdio are enabled doesn't work, but it will be necessary when device tree support is implemented. Signed-off-by:
Felipe Balbi <balbi@ti.com>
-
Luciano Coelho authored
The platform devices can be created by both wlcore_sdio and wlcore_spi. Theoretically, if both are connected to the same board, there will be a conflict. Reported-by:
-
Luciano Coelho authored
Just a small cleanup to use the pointer provided by wlcore_pdev_data instead of using a separate pointer then copying. Reviewed-by:
-
Luciano Coelho authored
We can't pass pointers from the platform data to the modules, because with DT it cannot be done. Those pointers are not set by the board files anyway. It's the bus modules that set them, so they can be safely removed from the platform data without changing any board files. Create a new structure that the bus modules pass to wlcore. This structure contains the if_ops pointers and a pointer to the actual platform data. Signed-off-by:
-
Luciano Coelho authored
There is no platform-specific set_power method anymore. Power setting is done in the bus modules (wlcore_sdio and wlcore_spi). Signed-off-by:
-
