After the common MIPS CPU interrupt controller (for irq0-7) was introduced
the Lasat boards didn't get their interrupts right, so nothing worked. The
old routines need to be offset by the new 8 hardware interrupts common to
all MIPS CPU's.
Signed-off-by: Thomas Horsten <thomas@horsten.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 The SWARM defconfig file has not been regenerated for over a year now.
Here is a patch to bring the file up to date.  Additionally some important
and sometimes confusing changes happened meanwhile.  Here is the list of
notable corresponding updates to the configuration:

1. CPU_SB1_PASS_2_2 is now selected rather than CPU_SB1_PASS_1.  The
   latter requires a non-standard -msb1-pass1-workarounds option to be
   supported by GCC and I am told is quite rare anyway.

   [Ralf: Afaik -msb1-pass1-workarounds is available only in Monta Vista's
   special Sibyte gcc 3.0 variant and gcc 3.0 is too old to build a modern
   kernel anyway.]

2. PHYLIB and BROADCOM_PHY are both built in and NETDEV_1000 enabled as
   required by SB1250_MAC.

3. USB and USB_OHCI_HCD are enabled as there is an OHCI chip onboard.

4. TMPFS is enabled, because I use it. ;-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 Build the SWARM platform library is as an object rather than an archive
so that files which only contain symbols used by initcalls and do not
provide any symbols that would pull them from an archive still work.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Build error was caused by commit 35133692.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

RM200 with R5ks have a little bit different arcname.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use better load address for big endian kernels to avoid clashes with
PROM / SASH.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Correctly initialize io_map_base for the SB1250 PCI controller as required
for proper iomap support.  Based on a proposal from Daniel Jacobowitz.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In the conversion done in the commits

  95c4eb3ef4484ca85da5c98780d358cffd546b90
  9d360ab4

  [MIPS] Alchemy: Renumber interrupts so irq_cpu can work.

one reserved interrupt on au1500 was missed. this broke the au1000 ethernet
driver.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide-generic: don't probe all legacy ISA IDE ports by default
  ide-cs: fix releasing I/O resources
  ide-cs: fix probing and add warm-plug support
  ide-pmac: remove bogus comment about pmac_ide_setup_device()
  ide-pmac: add ->cable_detect method
  ide-pmac: bugfix for media-bay support rework
  opti621: add PIO 4 support
  opti621: use pre-calculated PIO timings
  opti621: program devices timings separately in ->set_pio_mode
  opti621: use PCI clock value provided by controller
  opti621: remove DMA support
  opti621: disable read prefetch

lguest (in rusty's use-tun-ringfd patch) assumes that the
guest has updated its feature bits before setting its status
to VIRTIO_CONFIG_S_DRIVER_OK.

That's pretty reasonable, so let's make it so.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We can't probe all legacy ISA IDE ports by default as the resources may be
occupied by other ISA devices.  Add "probe_mask" module parameter and probe
only first two ISA IDE ports by default leaving the decision about probing
the rest to the user (systems with ISA ide2-6 should be very, very rare).

This fixes a regression caused by:

commit 343a3451
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Tue Jun 10 20:56:36 2008 +0200

    ide-generic: add missing hwif->chipset setup
...
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Bisected-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

hwif content is already freed after ide_release() call so cache
hwif->io_ports.{data,ctl}_addr in local variables in ide_detach().

This fixes post-2.6.25 regression.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix probing by using ide_port_scan() and moving "retry loop"
  from ide_config() to idecs_register().

* Don't fail probe if there are no devices attached to a port.

* Remove (now redundant) error message from ide_config().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->cable_detect method and remove no longer needed pmif->cable_80 flag
(there is also no need to mask ->udma_mask now).

This fixes:

- forced ignoring of cable detection (needed for some CF devices & debug)

- cable detection for warm-plug

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix bug introduced by:

commit 2dde7861
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Fri Apr 18 00:46:23 2008 +0200

    ide: rework PowerMac media-bay support (take 2)
...

[ Yeah, I suck. ]

bay->cd_index shouldn't be changed if IDE devices are not present
or retry operations won't happen.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add PIO 4 support.

While at it:

* Use a single struct ide_port_info instance for OPTi621 and OPTi621X.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use pre-calculated PIO timings in ->set_pio_mode.

* Remove no longer needed compute_clocks(), cmpt_clk(), struct pio_clocks_s,
  PIO_* defines and OPTI621_DEBUG define.

There should be no functional changes caused by this patch.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Set drive->drive_data to 'pio + XFER_PIO_0' instead of 'pio',
  then simplify selecting maximum adress setup timing.

* Remove no longer needed compute_pios() and opti621_port_init_devs().

* Program devices timings separately in ->set_pio_mode.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use PCI clock value provided by controller instead of depending on
a default (or user supplied) value.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

These controllers don't support DMA.

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This fixes 2.6.25 regression (kernel.org bugzilla bug #10723) caused by:

commit 912fb29a
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Fri Oct 19 00:30:11 2007 +0200

    opti621: always tune PIO
...

Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Bisected-by: Juergen Kosel <juergen.kosel@gmx.de>
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: fixup write combine comment in pci_mmap_resource
  x86: PAT export resource_wc in pci sysfs
  x86, pci-dma.c: don't always add __GFP_NORETRY to gfp
  suspend-vs-iommu: prevent suspend if we could not resume
  x86: pci-dma.c: use __GFP_NO_OOM instead of __GFP_NORETRY
  pci, x86: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
  PCI: use dev_to_node in pci_call_probe
  PCI: Correct last two HP entries in the bfsort whitelist

* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: update my email address
  parisc: fix miscompilation of ip_fast_csum with gcc >= 4.3
  parisc: fix off by one in setup_sigcontext32
  parisc: export empty_zero_page
  parisc: export copy_user_page_asm
  parisc: move head.S to head.text section
  Revert "parisc: fix trivial section name warnings"

Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

ip_fast_csum needs an asm "memory" clobber, otherwise the aggressive
optimizations in gcc-4.3 cause it to be miscompiled.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Thankfully, the values were irrelevant... Spotted by
newer gcc.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Needed by ext4 when built as a module.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

Needed by fuse (via copy_highpage).
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

And explicitly list it in vmlinux.lds...
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

This reverts commit bd3bb8c1.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ahci: Workaround HW bug for SB600/700 SATA controller PMP support
  ahci: workarounds for mcp65

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  tcp: Revert 'process defer accept as established' changes.
  ipv6: Fix duplicate initialization of rawv6_prot.destroy
  bnx2x: Updating the Maintainer
  net: Eliminate flush_scheduled_work() calls while RTNL is held.
  drivers/net/r6040.c: correct bad use of round_jiffies()
  fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
  ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
  netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
  netfilter: Make nflog quiet when no one listen in userspace.
  ipv6: Fail with appropriate error code when setting not-applicable sockopt.
  ipv6: Check IPV6_MULTICAST_LOOP option value.
  ipv6: Check the hop limit setting in ancillary data.
  ipv6 route: Fix route lifetime in netlink message.
  ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
  dccp: Bug in initial acknowledgment number assignment
  dccp ccid-3: X truncated due to type conversion
  dccp ccid-3: TFRC reverse-lookup Bug-Fix
  dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
  dccp: Fix sparse warnings
  dccp ccid-3: Bug-Fix - Zero RTT is possible

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: get leo framebuffer working

There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability.  Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>