Merge tag 'mac80211-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"This contains another small set of fixes for 3.18, these are all
over the place and most of the bugs are old, one even dates back
to the original mac80211 we merged into the kernel."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"I fix here two issues that are related to the firmware
loading flow. A user reported that he couldn't load the
driver because the rfkill line was pulled up while we
were running the calibrations. This was happening while
booting the system: systemd was restoring the "disable
wifi settings" and that raised an RFKILL interrupt during
the calibration. Our driver didn't handle that properly
and this is now fixed."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.

Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.

This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231

CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.

Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.

Cc: stable@vger.kernel.org
Reported-by: Yosef Khyal <yosefx.khyal@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

An error in the code makes the allocated space for firmware to be too
small.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new version of rtlwifi needs code in rtl92ce_get_desc() that returns
the buffer address for read operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new version of rtlwifi needs code in rtl92se_get_desc() that returns
the buffer address for read operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver rtlwifi has been modified to call ieee80211_register_hw()
from the probe routine; however, the existing call in the callback
routine for deferred firmware loading was not removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The recent changes in checking for Bluetooth status added some callbacks to code
in rtlwifi. To make certain that all callbacks are defined, a dummy routine has been
added to rtlwifi, and the drivers that need to use it are modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During 11n RX reordering, if there is a hole in RX table,
driver will not send packets to kernel until the rxreorder
timer expires or the table is full.
However, currently driver always restarts rxreorder timer when
receiving a packet, which causes the timer hardly to expire.
So while connected with to 11n AP in a busy environment,
ping packets may get blocked for about 30 seconds.

This patch fixes this timer restarting by ensuring rxreorder timer
would only be restarted either timer is not set or start_win
has changed.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Plus Chen <pchen@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The right shift operation has higher precedence than the mask so we
left shift by "(i * 3)" and then immediately right shift by "(i * 3)"
then we mask.  It should be left shift, mask, and then right shift.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle

References: https://bugs.debian.org/766802Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.

However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.

To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.

Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Due to the time it takes to process the beacon that started the CSA
process, we may be late for the switch if we try to reach exactly
beacon 0.  To avoid that, use count - 1 when calculating the switch time.

Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If we are switching from an HT40+ to an HT40- channel (or vice-versa),
we need the secondary channel offset IE to specify what is the
post-CSA offset to be used.  This applies both to beacons and to probe
responses.

In ieee80211_parse_ch_switch_ie() we were ignoring this IE from
beacons and using the *current* HT information IE instead.  This was
causing us to use the same offset as before the switch.

Fix that by using the secondary channel offset IE also for beacons and
don't ever use the pre-switch offset.  Additionally, remove the
"beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not
needed anymore.

Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Userspace can add keys to an AP mode interface before start_ap has been
called. If there have been no calls to start_ap/stop_ap in the mean
time, the keys will still be around when the interface is brought down.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[adjust comments, fix AP_VLAN case]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The driver is not released when ieee80211_register_hw fails in
mac80211_hwsim_create_radio, leading to the access to the unregistered (and
possibly freed) device in platform_driver_unregister:

[    0.447547] mac80211_hwsim: ieee80211_register_hw failed (-2)
[    0.448292] ------------[ cut here ]------------
[    0.448854] WARNING: CPU: 0 PID: 1 at ../include/linux/kref.h:47 kobject_get+0x33/0x50()
[    0.449839] CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00001-gdd46990-dirty #2
[    0.450813] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.451512]  00000000 00000000 78025e38 7967c6c6 78025e68 7905e09b 7988b480 00000000
[    0.452579]  00000001 79887d62 0000002f 79170bb3 79170bb3 78397008 79ac9d74 00000001
[    0.453614]  78025e78 7905e15d 00000009 00000000 78025e84 79170bb3 78397000 78025e8c
[    0.454632] Call Trace:
[    0.454921]  [<7967c6c6>] dump_stack+0x16/0x18
[    0.455453]  [<7905e09b>] warn_slowpath_common+0x6b/0x90
[    0.456067]  [<79170bb3>] ? kobject_get+0x33/0x50
[    0.456612]  [<79170bb3>] ? kobject_get+0x33/0x50
[    0.457155]  [<7905e15d>] warn_slowpath_null+0x1d/0x20
[    0.457748]  [<79170bb3>] kobject_get+0x33/0x50
[    0.458274]  [<7925824f>] get_device+0xf/0x20
[    0.458779]  [<7925b5cd>] driver_detach+0x3d/0xa0
[    0.459331]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.459927]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.460660]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.461248]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.461824]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.462507]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.463161]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.463758]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.464393]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.465001]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.465569]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.466345]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.466972]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.467546]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.468072]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.468658]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.469303]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.469829] ---[ end trace ad8ac403ff8aef5c ]---
[    0.470509] ------------[ cut here ]------------
[    0.471047] WARNING: CPU: 0 PID: 1 at ../kernel/locking/lockdep.c:3161 __lock_acquire.isra.22+0x7aa/0xb00()
[    0.472163] DEBUG_LOCKS_WARN_ON(id >= MAX_LOCKDEP_KEYS)
[    0.472774] CPU: 0 PID: 1 Comm: swapper Tainted: G        W      3.17.0-00001-gdd46990-dirty #2
[    0.473815] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.474492]  78025de0 78025de0 78025da0 7967c6c6 78025dd0 7905e09b 79888931 78025dfc
[    0.475515]  00000001 79888a93 00000c59 7907f33a 7907f33a 78028000 fffe9d09 00000000
[    0.476519]  78025de8 7905e10e 00000009 78025de0 79888931 78025dfc 78025e24 7907f33a
[    0.477523] Call Trace:
[    0.477821]  [<7967c6c6>] dump_stack+0x16/0x18
[    0.478352]  [<7905e09b>] warn_slowpath_common+0x6b/0x90
[    0.478976]  [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00
[    0.479658]  [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00
[    0.480417]  [<7905e10e>] warn_slowpath_fmt+0x2e/0x30
[    0.480479]  [<7907f33a>] __lock_acquire.isra.22+0x7aa/0xb00
[    0.480479]  [<79078aa5>] ? sched_clock_cpu+0xb5/0xf0
[    0.480479]  [<7907fd06>] lock_acquire+0x56/0x70
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<79682d11>] mutex_lock_nested+0x61/0x2a0
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<7925b5e8>] driver_detach+0x58/0xa0
[    0.480479]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.480479]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.480479]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.480479]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.480479]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.480479]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.480479]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.480479]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.480479]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.480479]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.480479]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.480479]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.480479]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.480479]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.480479]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.480479]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.480479]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.480479] ---[ end trace ad8ac403ff8aef5d ]---
[    0.495478] BUG: unable to handle kernel paging request at 00200200
[    0.496257] IP: [<79682de5>] mutex_lock_nested+0x135/0x2a0
[    0.496923] *pde = 00000000
[    0.497290] Oops: 0002 [#1]
[    0.497653] CPU: 0 PID: 1 Comm: swapper Tainted: G        W      3.17.0-00001-gdd46990-dirty #2
[    0.498659] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.499321] task: 78028000 ti: 78024000 task.ti: 78024000
[    0.499955] EIP: 0060:[<79682de5>] EFLAGS: 00010097 CPU: 0
[    0.500620] EIP is at mutex_lock_nested+0x135/0x2a0
[    0.501145] EAX: 00200200 EBX: 78397434 ECX: 78397460 EDX: 78025e70
[    0.501816] ESI: 00000246 EDI: 78028000 EBP: 78025e8c ESP: 78025e54
[    0.502497]  DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
[    0.503076] CR0: 8005003b CR2: 00200200 CR3: 01b9d000 CR4: 00000690
[    0.503773] Stack:
[    0.503998]  00000000 00000001 00000000 7925b5e8 78397460 7925b5e8 78397474 78397460
[    0.504944]  00200200 11111111 78025e70 78397000 79ac9d74 00000001 78025ea0 7925b5e8
[    0.505451]  79ac9d74 fffffffe 00000001 78025ebc 7925a3ff 7a251398 78025ec8 7925bf80
[    0.505451] Call Trace:
[    0.505451]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.505451]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.505451]  [<7925b5e8>] driver_detach+0x58/0xa0
[    0.505451]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.505451]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.505451]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.505451]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.505451]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.505451]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.505451]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.505451]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.505451]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.505451]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.505451]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.505451]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.505451]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.505451]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.505451]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.505451]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.505451]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.505451] Code: 89 d8 e8 cf 9b 9f ff 8b 4f 04 8d 55 e4 89 d8 e8 72 9d 9f ff 8d 43 2c 89 c1 89 45 d8 8b 43 30 8d 55 e4 89 53 30 89 4d e4 89 45 e8 <89> 10 8b 55 dc 8b 45 e0 89 7d ec e8 db af 9f ff eb 11 90 31 c0
[    0.505451] EIP: [<79682de5>] mutex_lock_nested+0x135/0x2a0 SS:ESP 0068:78025e54
[    0.505451] CR2: 0000000000200200
[    0.505451] ---[ end trace ad8ac403ff8aef5e ]---
[    0.505451] Kernel panic - not syncing: Fatal exception

Fixes: 9ea92774 ("mac80211_hwsim: Register and bind to driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Junjie Mao <eternal.n08@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mvm->cur_ucode wasn't set before we actually load the
firmware. This caused issues when we boot in RFKILL since
we get an RFKILL interrupt upon boot even before we load
any firmware.
This leads to issues since iwl_mvm_set_hw_rfkill_state
(the RFKILL interrupts handler in mvm) relies on this
variable.

Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Merge tag 'mac80211-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.

Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit aa11bbf3.
This commit was causing connection issues and is not needed
if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default.

Regardless of the issues mentioned above, this patch added the
following WARNING:

WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]()
Got an HT rate for a non data frame 0x8
CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G           O   3.17.0+ #6
Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014
 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52
 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600
 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020
Call Trace:
 [<ffffffff814fa911>] ? dump_stack+0x41/0x51
 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90
 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50
 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]
 [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm]
 [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm]
 [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211]
 [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211]
 [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211]
 [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0
 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0
 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0
 [<ffffffff8142f670>] ? ether_setup+0x70/0x70
 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110
 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40
 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0
 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60
 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0
 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180
 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70
 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f
---[ end trace cc19a150d311fc63 ]---

which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:

iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]

Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.

This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581

But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:

https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809

Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.

Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.

We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The probe requests sent during scan must get BT prio 3.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Cc: <stable@vger.kernel.org> [3.16+]
Fixes: 2adc8949 ("iwlwifi: mvm: BT Coex - fix boost register / LUT values")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.

Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Drivers that do not use the get_btc_status() callback may not define a
dummy routine. The caller needs to check before making the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Thadeu Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In a previous patch the call to ieee80211_register_hw was moved from the
load firmware callback to the rtl_pci_probe only.
rt8192cu also uses this callback. Currently it doesnt create a wlan%d device.
Fill in the call to ieee80211_register_hw in rtl_usb_probe.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Initialize function pointer with a function indicating bt coexist is not there.
Prevents Ooops.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The kbuild test robot reported a possible array overrun. The affected code
checks for overruns, but fails to take the steps necessary to fix them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.

Bug: https://dev.openwrt.org/ticket/18164

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name
can never accidentally leak information via a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was found attached to the BCM47081A0 SoC. Log:
bcma: bus0: Found chip with id 43228, rev 0x00 and package 0x08
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And changed from using strncat to strlcat to simplify code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>