The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221118224540.619276-597-uwe@kleine-koenig.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

Synchronize the reported information in dmesg and the watchdog APIs.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221125221240.2818-1-linux@weissschuh.netSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

On some SoCs the watchdog device is actually mixed with timer, e.g.
the qcom,msm-timer on older Qualcomm SoCs where this is actually one
hardware block responsible for both system timer and watchdog.

Allow calling such device nodes as "timer".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221212174933.208900-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

Machine resets via da9062/da9063 PMICs are challenging since one needs
to use special i2c atomic transfers due to the fact interrupts are
disabled in such late system stages. This is the reason both PMICs don't
use regmap and have instead opted for i2c_smbus_write_byte_data() in
restart handlers.

However extensive testing revealed that even using atomic safe function
is not enough and occasional resets fail with error message "Failed to
shutdown (err =  -11)". This is due to the fact that function
i2c_smbus_write_byte_data() in turn calls __i2c_lock_bus_helper()
which might fail with -EAGAIN when bus lock is already taken and cannot
be released anymore.

Thus replace i2c_smbus_write_byte_data() with unlocked flavor of
i2c_smbus_xfer() function to avoid above dead-lock scenario. At this
system stage we don't care about proper locking anymore and only want
proper machine reset to be carried out.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221216083645.2574077-1-primoz.fiser@norik.com
[groeck: Fixed continuation line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

As per the specification the action QUERY_COUNTDOWN_PERIOD is optional.
If the action is not implemented by the physical device the driver would
always report "0" from get_timeleft().
Avoid confusing userspace by only providing get_timeleft() when
implemented by the hardware.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221221-wdat_wdt-timeleft-v1-1-8e8a314c36cc@weissschuh.netSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/6f312af6160d1e10b616c9adbd1fd8f822db964d.1672473415.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/13e8cdf17556da111d1d98a8fe0b1dc1c78007e2.1672417940.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/b1f8b5453791035ad534bd5ed36b49798ff4d9b2.1672418166.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/7c2d5f3815949faf6d3a0237a7b5f272f00a7ae9.1672418969.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/ccb096879a1309b9918ae956d6bdb9668c69bcda.1672473617.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9c055911e9f557b7239000c8e6cfa0cc393a19e9.1672474203.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/14b521b821279bc5111dc80b55d0936c5767c737.1672418470.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/f23a2cf84958adca255b82fd688e7cee0461760f.1672484376.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/6a4cf8e8b9d8f555c77395ba2ecadc205553774d.1672483046.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/6c5948373d309408095c1a098b7b4c491c5265f7.1672490071.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/615c6c3c46c3ee8e3136725af0ab0b51e1298091.1672474336.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1f8d1ce1e6a63c507a291aea624b1337326cc563.1672483996.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/2b041dc8230a4ed255051bb2d323da8a51a8d0be.1672491445.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/d4c675190d3ddfbba5c354edb4274757f9117304.1672489554.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/f9a4dcfc6d31bd9c1417e2d97a40cc2c1dbc6f30.1672496405.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/4335b4201b535ebc749a98bad0b99e3cb5317c39.1672496563.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/61f4e39db4c88408ee0149580e9aa925b784bc93.1672496714.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

The devm_clk_get_enabled() helper:
   - calls devm_clk_get()
   - calls clk_prepare_enable() and registers what is needed in order to
     call clk_disable_unprepare() when needed, as a managed resource.

This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/5e4255782fbb43d1b4b5cd03bd12d7a184497134.1672498920.git.christophe.jaillet@wanadoo.frSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

In some cases, the MediaTek watchdog requires the TOPRGU to reset
timer after system resets.

Provide a reset_by_toprgu parameter for configuration.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230117014023.2993-3-allen-kh.cheng@mediatek.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

In some applications, the mtk-wdt requires the TOPRGU (Top Reset
Generation Unit) to reset timer after system resets. Add optional
mediatek,reset-by-toprgu property to enable it.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230117014023.2993-2-allen-kh.cheng@mediatek.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>

Pull ELF fix from Al Viro:
 "One of the many equivalent build warning fixes for !CONFIG_ELF_CORE
  configs. Geert's is the earliest one I've been able to find"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  coredump: Move dump_emit_page() to kill unused warning

Pull USB fixes from Greg KH:
 "Here are some small USB fixes that resolve some reported problems.
  These include:

   - gadget driver fixes

   - dwc3 driver fix

   - typec driver fix

   - MAINTAINERS file update.

  All of these have been in linux-next with no reported problems"

* tag 'usb-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: ucsi: Don't attempt to resume the ports before they exist
  usb: gadget: udc: do not clear gadget driver.bus
  usb: gadget: f_uac2: Fix incorrect increment of bNumEndpoints
  usb: gadget: f_fs: Fix unbalanced spinlock in __ffs_ep0_queue_wait
  usb: dwc3: qcom: enable vbus override when in OTG dr-mode
  MAINTAINERS: Add myself as UVC Gadget Maintainer

Pull tty/serial driver fixes from Greg KH:
 "Here are some small serial and vt fixes. These include:

   - 8250 driver fixes relating to dma issues

   - stm32 serial driver fix for threaded irqs

   - vc_screen bugfix for reported problems.

  All have been in linux-next for a while with no reported problems"

* tag 'tty-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF
  serial: 8250_dma: Fix DMA Rx rearm race
  serial: 8250_dma: Fix DMA Rx completion race
  serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler

Pull char/misc driver fixes from Greg KH:
 "Here are a number of small char/misc/whatever driver fixes. They
  include:

   - IIO driver fixes for some reported problems

   - nvmem driver fixes

   - fpga driver fixes

   - debugfs memory leak fix in the hv_balloon and irqdomain code
     (irqdomain change was acked by the maintainer)

  All have been in linux-next with no reported problems"

* tag 'char-misc-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
  kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
  HV: hv_balloon: fix memory leak with using debugfs_lookup()
  nvmem: qcom-spmi-sdam: fix module autoloading
  nvmem: core: fix return value
  nvmem: core: fix cell removal on error
  nvmem: core: fix device node refcounting
  nvmem: core: fix registration vs use race
  nvmem: core: fix cleanup after dev_set_name()
  nvmem: core: remove nvmem_config wp_gpio
  nvmem: core: initialise nvmem->id early
  nvmem: sunxi_sid: Always use 32-bit MMIO reads
  nvmem: brcm_nvram: Add check for kzalloc
  iio: imu: fxos8700: fix MAGN sensor scale and unit
  iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
  iio: imu: fxos8700: fix failed initialization ODR mode assignment
  iio: imu: fxos8700: fix incorrect ODR mode readback
  iio: light: cm32181: Fix PM support on system with 2 I2C resources
  iio: hid: fix the retval in gyro_3d_capture_sample
  iio: hid: fix the retval in accel_3d_capture_sample
  iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
  ...

Pull fbdev fixes from Helge Deller:

 - fix fbcon to prevent fonts bigger than 32x32 pixels to avoid
   overflows reported by syzbot

 - switch omapfb to use kstrtobool()

 - switch some fbdev drivers to use the backlight helpers

* tag 'fbdev-for-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
  fbcon: Check font dimension limits
  fbdev: omapfb: Use kstrtobool() instead of strtobool()
  fbdev: fbmon: fix function name in kernel-doc
  fbdev: atmel_lcdfb: Rework backlight status updates
  fbdev: riva: Use backlight helper
  fbdev: omapfb: panel-dsi-cm: Use backlight helper
  fbdev: nvidia: Use backlight helper
  fbdev: mx3fb: Use backlight helper
  fbdev: radeon: Use backlight helper
  fbdev: atyfb: Use backlight helper
  fbdev: aty128fb: Use backlight helper

Pull x86 fix from Borislav Petkov:

 - Prevent the compiler from reordering accesses to debug regs which
   could cause a #VC exception in SEV-ES guests at the wrong place in
   the NMI handling path

* tag 'x86_urgent_for_v6.2_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/debug: Fix stack recursion caused by wrongly ordered DR7 accesses

Pull perf fix from Borislav Petkov:

 - Lock the proper critical section when dealing with perf event context

* tag 'perf_urgent_for_v6.2_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix perf_event_pmu_context serialization

Pull powerpc fixes from Michael Ellerman:
 "It's a bit of a big batch for rc6, but just because I didn't send any
  fixes the last week or two while I was on vacation, next week should
  be quieter:

   - Fix a few objtool warnings since we recently enabled objtool.

   - Fix a deadlock with the hash MMU vs perf record.

   - Fix perf profiling of asynchronous interrupt handlers.

   - Revert the IMC PMU nest_init_lock to being a mutex.

   - Two commits fixing problems with the kexec_file FDT size
     estimation.

   - Two commits fixing problems with strict RWX vs kernels running at
     non-zero.

   - Reconnect tlb_flush() to hash__tlb_flush()

  Thanks to Kajol Jain, Nicholas Piggin, Sachin Sant Sathvika Vasireddy,
  and Sourabh Jain"

* tag 'powerpc-6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Reconnect tlb_flush() to hash__tlb_flush()
  powerpc/kexec_file: Count hot-pluggable memory in FDT estimate
  powerpc/64s/radix: Fix RWX mapping with relocated kernel
  powerpc/64s/radix: Fix crash with unaligned relocated kernel
  powerpc/kexec_file: Fix division by zero in extra size estimation
  powerpc/imc-pmu: Revert nest_init_lock to being a mutex
  powerpc/64: Fix perf profiling asynchronous interrupt handlers
  powerpc/64s: Fix local irq disable when PMIs are disabled
  powerpc/kvm: Fix unannotated intra-function call warning
  powerpc/85xx: Fix unannotated intra-function call warning

Pull RTC fixes from Alexandre Belloni:
 "Here are a few fixes for 6.2. The EFI one is the most important as it
  allows some RTCs to actually work. The other two are warnings that are
  worth fixing.

   - efi: make WAKEUP services optional

   - sunplus: fix format string warning"

* tag 'rtc-6.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: sunplus: fix format string for printing resource
  dt-bindings: rtc: qcom-pm8xxx: allow 'wakeup-source' property
  rtc: efi: Enable SET/GET WAKEUP services as optional

Merge tag 'kbuild-fixes-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix two bugs (for building and for signing) when MODULE_SIG_KEY
   contains a PKCS#11 URI

* tag 'kbuild-fixes-v6.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: modinst: Fix build error when CONFIG_MODULE_SIG_KEY is a PKCS#11 URI
  certs: Fix build error when PKCS#11 URI contains semicolon

Pull kvm fixes from Paolo Bonzini:
 "ARM64:

   - Yet another fix for non-CPU accesses to the memory backing the
     VGICv3 subsystem

   - A set of fixes for the setlftest checking for the S1PTW behaviour
     after the fix that went in ealier in the cycle"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: selftests: aarch64: Test read-only PT memory regions
  KVM: selftests: aarch64: Fix check of dirty log PT write
  KVM: selftests: aarch64: Do not default to dirty PTE pages on all S1PTWs
  KVM: selftests: aarch64: Relax userfaultfd read vs. write checks
  KVM: arm64: Allow no running vcpu on saving vgic3 pending table
  KVM: arm64: Allow no running vcpu on restoring vgic3 LPI pending status
  KVM: arm64: Add helper vgic_write_guest_lock()

Pull parisc architecture fixes from Helge Deller:

 - Fix PTRACE_GETREGS/PTRACE_SETREGS for 32-bit userspace on a 64-bit
   kernel

 - pdc_iodc_print() dropped chars for newline in strings

 - Drop constants in favour of PRIV_USER

 - use safer strscpy() function in pdc_stable driver

* tag 'parisc-for-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Wire up PTRACE_GETREGS/PTRACE_SETREGS for compat case
  parisc: Replace hardcoded value with PRIV_USER constant in ptrace.c
  parisc: Fix return code of pdc_iodc_print()
  parisc: pdc_stable: use strscpy() to instead of strncpy()

Pull OpenRISC mailing list update from Stafford Horne:
 "The old mailing list for OpenRISC died due to some infrastructure
  issues and the people in charge decided not to keep it running. We
  have migrated this and the users over to kernel.org infrastructure.

  Sending this out now to avoid kernel developers getting lots of
  bounced mails for using the old list"

* tag 'for-linus' of https://github.com/openrisc/linux:
  MAINTAINERS: Update OpenRISC mailing list

Merge tag 'kvmarm-fixes-6.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 fixes for 6.2, take #3

- Yet another fix for non-CPU accesses to the memory backing
  the VGICv3 subsystem

- A set of fixes for the setlftest checking for the S1PTW
  behaviour after the fix that went in ealier in the cycle