- 18 Apr, 2016 40 commits
-
-
Brent Taylor authored
[ Upstream commit 93c77d29 ] Using an at91sam9g20ek development board with DTS configuration may trigger a kernel panic because of a NULL pointer dereference exception, while configuring DMA. Let's fix this by adding a check for pdata before dereferencing it. Signed-off-by:
Brent Taylor <motobud@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
Mans Rullgard authored
[ Upstream commit 74843787 ] Commit ecb89f2f ("mmc: atmel-mci: remove compat for non DT board when requesting dma chan") broke dma on AVR32 and any other boards not using DT. This restores a fallback mechanism for such cases. Signed-off-by:
Mans Rullgard <mans@mansr.com> Acked-by:
Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> Acked-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
-
Adrian Hunter authored
[ Upstream commit 99513624 ] Normally the timeout clock frequency is read from the capabilities register. It is also possible to set the value prior to calling sdhci_add_host() in which case that value will override the capabilities register value. However that was being done after calculating max_busy_timeout so that max_busy_timeout was being calculated using the wrong value of timeout_clk. Fix that by moving the override before max_busy_timeout is calculated. The result is that the max_busy_timeout and max_discard increase for BSW devices so that, for example, the time for mkfs.ext4 on a 64GB eMMC drops from about 1 minute 40 seconds to about 20 seconds. Note, in the future, the capabilities setting will be tidied up and this override won't be used anymore. However this fix is needed for stable. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org # v3.18+ Signed-off-by:
-
Andy Lutomirski authored
[ Upstream commit c29016cf ] iopl(3) is supposed to work if iopl is already 3, even if unprivileged. This didn't work right on Xen PV. Fix it. Reviewewd-by:
Jan Beulich <JBeulich@suse.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <JBeulich@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/8ce12013e6e4c0a44a97e316be4a6faff31bd5ea.1458162709.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Dmitry V. Levin authored
[ Upstream commit 5f8d498d ] Explicitly check show_devname method return code and bail out in case of an error. This fixes regression introduced by commit 9d4d6574. Cc: stable@vger.kernel.org Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
J. Bruce Fields authored
[ Upstream commit 2f6fc056 ] nfsd_lookup_dentry exits with the parent filehandle locked. fh_put also unlocks if necessary (nfsd filehandle locking is probably too lenient), so it gets unlocked eventually, but if the following op in the compound needs to lock it again, we can deadlock. A fuzzer ran into this; normal clients don't send a secinfo followed by a readdir in the same compound. Cc: stable@vger.kernel.org Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 447d6275 ] Add some sanity check codes before actually accessing the endpoint via get_endpoint() in order to avoid the invalid access through a malformed USB descriptor. Mostly just checking bNumEndpoints, but in one place (snd_microii_spdif_default_get()), the validity of iface and altsetting index is checked as well. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125 Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 0f886ca1 ] create_fixed_stream_quirk() may cause a NULL-pointer dereference by accessing the non-existing endpoint when a USB device with a malformed USB descriptor is used. This patch avoids it simply by adding a sanity check of bNumEndpoints before the accesses. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125 Cc: <stable@vger.kernel.org> Signed-off-by:
-
Magnus Damm authored
[ Upstream commit bcdc9f26 ] This patch fixes the MMC SPI driver from doing polling card detect when a CD GPIO that supports interrupts is specified using the gpios DT property. Without this patch the DT node below results in the following output: spi_gpio: spi-gpio { /* SD2 @ CN12 */ compatible = "spi-gpio"; #address-cells = <1>; #size-cells = <0>; gpio-sck = <&gpio6 16 GPIO_ACTIVE_HIGH>; gpio-mosi = <&gpio6 17 GPIO_ACTIVE_HIGH>; gpio-miso = <&gpio6 18 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; cs-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>; status = "okay"; spi@0 { compatible = "mmc-spi-slot"; reg = <0>; voltage-ranges = <3200 3400>; spi-max-frequency = <25000000>; gpios = <&gpio6 22 GPIO_ACTIVE_LOW>; /* CD */ }; }; # dmesg | grep mmc mmc_spi spi32766.0: SD/MMC host mmc0, no WP, no poweroff, cd polling mmc0: host does not support reading read-only switch, assuming write-enable mmc0: new SDHC card on SPI mmcblk0: mmc0:0000 SU04G 3.69 GiB mmcblk0: p1 With this patch applied the "cd polling" portion above disappears. Signed-off-by:
Magnus Damm <damm+renesas@opensource.se> Cc: stable@vger.kernel.org # v3.18+ Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 1f7c6658 ] Cirrus HD-audio driver may adjust GPIO pins for EAPD dynamically depending on the jack plug state. This works fine for the auto-mute mode where the speaker gets muted upon the HP jack plug. OTOH, when the auto-mute mode is off, this turns off the EAPD unexpectedly depending on the jack state, which results in the silent speaker output. This patch fixes the silent speaker output issue by setting GPIO bits constantly when the auto-mute mode is off. Reported-and-tested-by: moosotc@gmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dmitry Torokhov authored
[ Upstream commit 3b654288 ] Even though hid_hw_* checks that passed in data_len is less than HID_MAX_BUFFER_SIZE it is not enough, as i2c-hid does not necessarily allocate buffers of HID_MAX_BUFFER_SIZE but rather checks all device reports and select largest size. In-kernel users normally just send as much data as report needs, so there is no problem, but hidraw users can do whatever they please: BUG: KASAN: slab-out-of-bounds in memcpy+0x34/0x54 at addr ffffffc07135ea80 Write of size 4101 by task syz-executor/8747 CPU: 2 PID: 8747 Comm: syz-executor Tainted: G BU 3.18.0 #37 Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT) Call trace: [<ffffffc00020ebcc>] dump_backtrace+0x0/0x258 arch/arm64/kernel/traps.c:83 [<ffffffc00020ee40>] show_stack+0x1c/0x2c arch/arm64/kernel/traps.c:172 [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffc001958114>] dump_stack+0x90/0x140 lib/dump_stack.c:50 [< inline >] print_error_description mm/kasan/report.c:97 [< inline >] kasan_report_error mm/kasan/report.c:278 [<ffffffc0004597dc>] kasan_report+0x268/0x530 mm/kasan/report.c:305 [<ffffffc0004592e8>] __asan_storeN+0x20/0x150 mm/kasan/kasan.c:718 [<ffffffc0004594e0>] memcpy+0x30/0x54 mm/kasan/kasan.c:299 [<ffffffc001306354>] __i2c_hid_command+0x2b0/0x7b4 drivers/hid/i2c-hid/i2c-hid.c:178 [< inline >] i2c_hid_set_or_send_report drivers/hid/i2c-hid/i2c-hid.c:321 [<ffffffc0013079a0>] i2c_hid_output_raw_report.isra.2+0x3d4/0x4b8 drivers/hid/i2c-hid/i2c-hid.c:589 [<ffffffc001307ad8>] i2c_hid_output_report+0x54/0x68 drivers/hid/i2c-hid/i2c-hid.c:602 [< inline >] hid_hw_output_report include/linux/hid.h:1039 [<ffffffc0012cc7a0>] hidraw_send_report+0x400/0x414 drivers/hid/hidraw.c:154 [<ffffffc0012cc7f4>] hidraw_write+0x40/0x64 drivers/hid/hidraw.c:177 [<ffffffc0004681dc>] vfs_write+0x1d4/0x3cc fs/read_write.c:534 [< inline >] SYSC_pwrite64 fs/read_write.c:627 [<ffffffc000468984>] SyS_pwrite64+0xec/0x144 fs/read_write.c:614 Object at ffffffc07135ea80, in cache kmalloc-512 Object allocated with size 268 bytes. Let's check data length against the buffer size before attempting to copy data over. Cc: stable@vger.kernel.org Reported-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
Dmitry Torokhov <dtor@chromium.org> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Dmitri Epshtein authored
[ Upstream commit 928b6519 ] Function eth_prepare_mac_addr_change() is called as part of MAC address change. This function check if interface is running. To enable change MAC address when interface is running: IFF_LIVE_ADDR_CHANGE flag must be set to dev->priv_flags field Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Cc: stable@vger.kernel.org Signed-off-by:
Dmitri Epshtein <dima@marvell.com> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Ming Lei authored
[ Upstream commit fafcde3a ] Inside multipath_make_request(), multipath maps the incoming bio into low level device's bio, but it is totally wrong to copy the bio into mapped bio via '*mapped_bio = *bio'. For example, .__bi_remaining is kept in the copy, especially if the incoming bio is chained to via bio splitting, so .bi_end_io can't be called for the mapped bio at all in the completing path in this kind of situation. This patch fixes the issue by using clone style. Cc: stable@vger.kernel.org (v3.14+) Reported-and-tested-by:
Andrea Righi <righi.andrea@gmail.com> Signed-off-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Alex Deucher authored
[ Upstream commit e5f243bd ] Move all the logic to radeon_fb.c and add checks to functions called frome elsewhere. bug: https://bugzilla.kernel.org/show_bug.cgi?id=112781Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Josh Boyer authored
[ Upstream commit 9c6ba456 ] The powermate driver expects at least one valid USB endpoint in its probe function. If given malicious descriptors that specify 0 for the number of endpoints, it will crash. Validate the number of endpoints on the interface before using them. The full report for this issue can be found here: http://seclists.org/bugtraq/2016/Mar/85Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Sebastian Ott authored
[ Upstream commit 80c544de ] The function measurement block must not cross a page boundary. Ensure that by raising the alignment requirement to the smallest power of 2 larger than the size of the fmb. Fixes: d0b08853 ("s390/pci: performance statistics and debug infrastructure") Cc: stable@vger.kernel.org # v3.8+ Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Seth Forshee authored
[ Upstream commit 744742d6 ] The 'reqs' member of fuse_io_priv serves two purposes. First is to track the number of oustanding async requests to the server and to signal that the io request is completed. The second is to be a reference count on the structure to know when it can be freed. For sync io requests these purposes can be at odds. fuse_direct_IO() wants to block until the request is done, and since the signal is sent when 'reqs' reaches 0 it cannot keep a reference to the object. Yet it needs to use the object after the userspace server has completed processing requests. This leads to some handshaking and special casing that it needlessly complicated and responsible for at least one race condition. It's much cleaner and safer to maintain a separate reference count for the object lifecycle and to let 'reqs' just be a count of outstanding requests to the userspace server. Then we can know for sure when it is safe to free the object without any handshaking or special cases. The catch here is that most of the time these objects are stack allocated and should not be freed. Initializing these objects with a single reference that is never released prevents accidental attempts to free the objects. Fixes: 9d5722b7 ("fuse: handle synchronous iocbs internally") Cc: stable@vger.kernel.org # v4.1+ Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Robert Doebbelin authored
[ Upstream commit 7cabc61e ] There's a race in fuse_direct_IO(), whereby is_sync_kiocb() is called on an iocb that could have been freed if async io has already completed. The fix in this case is simple and obvious: cache the result before starting io. It was discovered by KASan: kernel: ================================================================== kernel: BUG: KASan: use after free in fuse_direct_IO+0xb1a/0xcc0 at addr ffff88036c414390 Signed-off-by:
Robert Doebbelin <robert@quobyte.com> Signed-off-by:
-
Vittorio Gambaletta (VittGam) authored
[ Upstream commit 4061db03 ] The clock measurement on the AC'97 audio card found in the IBM ThinkPad X41 will often fail, so add a quirk entry to fix it. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=441087 Cc: <stable@vger.kernel.org> Signed-off-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Signed-off-by:
-
Sasha Levin authored
[ Upstream commit 3ec622f4 ] Vendor ID 0x10de0083 is used by a yet-to-be-named GPU chip. This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is appropriate here. Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
-
Aaron Plattner authored
[ Upstream commit 2d369c74 ] Vendor ID 0x10de0082 is used by a yet-to-be-named GPU chip. This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is appropriate here. Signed-off-by:
-
Fabio Estevam authored
[ Upstream commit 33b96d2c ] Currently we have an incorrect behaviour when multiple devices are present under the weim node. For example: &weim { ... status = "okay"; sram@0,0 { ... status = "okay"; }; mram@0,0 { ... status = "disabled"; }; }; In this case only the 'sram' device should be probed and not 'mram'. However what happens currently is that the status variable is ignored, causing the 'sram' device to be disabled and 'mram' to be enabled. Change the weim_parse_dt() function to use for_each_available_child_of_node()so that the devices marked with 'status = disabled' are not probed. Cc: <stable@vger.kernel.org> Suggested-by:
Wolfgang Netbal <wolfgang.netbal@sigmatek.at> Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by:
Sascha Hauer <s.hauer@pengutronix.de> Acked-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Max Filippov authored
[ Upstream commit 7de7ac78 ] There are XCHAL_NUM_DBREAK registers, clear them all. This also fixes cryptic assembler error message with binutils 2.25 when XCHAL_NUM_DBREAK is 0: as: out of memory allocating 18446744073709551575 bytes after a total of 495616 bytes Cc: stable@vger.kernel.org Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
[ Upstream commit a67cc9aa ] Disabling pagefault makes little sense there, preemption disabling is what was meant. Cc: stable@vger.kernel.org Signed-off-by:
-
Max Filippov authored
[ Upstream commit 362014c8 ] Simulator stdin may be connected to a file, when its end is reached kernel hangs in infinite loop inside rs_poll, because simc_poll always signals that descriptor 0 is readable and simc_read always returns 0. Check simc_read return value and exit loop if it's not positive. Also don't rewind polling timer if it's zero. Cc: stable@vger.kernel.org Signed-off-by:
-
Hui Wang authored
[ Upstream commit 6ef2f68f ] This Lenovo ThinkCentre AIO also uses Line2 as mic mute button and uses GPIO2 to control the mic mute led, so applying this quirk can make both the button and led work. Cc: stable@vger.kernel.org BugLink: https://bugs.launchpad.net/bugs/1555912Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Jenny Derzhavetz authored
[ Upstream commit f81bf458 ] No need to restrict this check to specific events. Signed-off-by:
Jenny Derzhavetz <jennyf@mellanox.com> Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Cc: stable@vger.kernel.org # v3.10+ Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Jenny Derzhavetz authored
[ Upstream commit aea92980 ] We need an indication that isert_conn->iscsi_conn binding has happened so we'll know not to invoke a connection reinstatement on an unbound connection which will lead to a bogus isert_conn->conn dereferece. Signed-off-by:
-
Jenny Derzhavetz authored
[ Upstream commit b89a7c25 ] Once connection request is accepted, one rx descriptor is posted to receive login request. This descriptor has rx type, but is outside the main pool of rx descriptors, and thus was mistreated as tx type. Signed-off-by:
-
Joe Thornber authored
[ Upstream commit 2eae9e44 ] If a transaction abort has failed then we can no longer use the metadata device. Typically this happens if the superblock is unreadable. This fix addresses a crash seen during metadata device failure testing. Fixes: 8a01a6af ("dm thin: prefetch missing metadata pages") Cc: stable@vger.kernel.org # 3.19+ Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Dmitry Tunin authored
[ Upstream commit 75c6aca4 ] T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3472 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb BugLink: https://bugs.launchpad.net/bugs/1552925Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Luck, Tony authored
[ Upstream commit eb1af3b7 ] Large memory Haswell-EX systems with multiple DIMMs per channel were sometimes reporting the wrong DIMM. Found three problems: 1) Debug printouts for socket and channel interleave were not interpreting the register fields correctly. The socket interleave field is a 2^X value (0=1, 1=2, 2=4, 3=8). The channel interleave is X+1 (0=1, 1=2, 2=3. 3=4). 2) Actual use of the socket interleave value didn't interpret as 2^X 3) Conversion of address to channel address was complicated, and wrong. Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Aristeu Rozanski <arozansk@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by:
-
OGAWA Hirofumi authored
[ Upstream commit c0a2ad9b ] On umount path, jbd2_journal_destroy() writes latest transaction ID (->j_tail_sequence) to be used at next mount. The bug is that ->j_tail_sequence is not holding latest transaction ID in some cases. So, at next mount, there is chance to conflict with remaining (not overwritten yet) transactions. mount (id=10) write transaction (id=11) write transaction (id=12) umount (id=10) <= the bug doesn't write latest ID mount (id=10) write transaction (id=11) crash mount [recovery process] transaction (id=11) transaction (id=12) <= valid transaction ID, but old commit must not replay Like above, this bug become the cause of recovery failure, or FS corruption. So why ->j_tail_sequence doesn't point latest ID? Because if checkpoint transactions was reclaimed by memory pressure (i.e. bdev_try_to_free_page()), then ->j_tail_sequence is not updated. (And another case is, __jbd2_journal_clean_checkpoint_list() is called with empty transaction.) So in above cases, ->j_tail_sequence is not pointing latest transaction ID at umount path. Plus, REQ_FLUSH for checkpoint is not done too. So, to fix this problem with minimum changes, this patch updates ->j_tail_sequence, and issue REQ_FLUSH. (With more complex changes, some optimizations would be possible to avoid unnecessary REQ_FLUSH for example though.) BTW, journal->j_tail_sequence = ++journal->j_transaction_sequence; Increment of ->j_transaction_sequence seems to be unnecessary, but ext3 does this. Signed-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 56dc66ff ] Just like CX20722, CX7024 codec also requires the power down at reboot in order to reduce the noise at reboot/shutdown. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=113511 Cc: <stable@vger.kernel.org> Signed-off-by:
-
Douglas Gilbert authored
[ Upstream commit 5ecee0a3 ] One of the strange things that the original sg driver did was let the user provide both a data-out buffer (it followed the sg_header+cdb) _and_ specify a reply length greater than zero. What happened was that the user data-out buffer was copied into some kernel buffers and then the mid level was told a read type operation would take place with the data from the device overwriting the same kernel buffers. The user would then read those kernel buffers back into the user space. From what I can tell, the above action was broken by commit fad7f01e ("sg: set dxferp to NULL for READ with the older SG interface") in 2008 and syzkaller found that out recently. Make sure that a user space pointer is passed through when data follows the sg_header structure and command. Fix the abnormal case when a non-zero reply_len is also given. Fixes: fad7f01e Cc: <stable@vger.kernel.org> #v2.6.28+ Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Reviewed-by:
Ewan Milne <emilne@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Mario Kleiner authored
[ Upstream commit 459ee1c3 ] As observed on Apple iMac10,1, DCE-3.2, RV-730, link rate of 2.7 Ghz is not selected, because the args.v1.ucConfig flag setting for 2.7 Ghz gets overwritten by a following assignment of the transmitter to use. Move link rate setup a few lines down to fix this. In practice this didn't have any positive or negative effect on display setup on the tested iMac10,1 so i don't know if backporting to stable makes sense or not. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by:
-
Alex Deucher authored
[ Upstream commit e64c952e ] Some PX laptops don't provide an ACPI method to control dGPU power. On those systems, the driver is responsible for handling the dGPU power state. Disable runtime PM on them until support for this is implemented. Reviewed-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
NeilBrown authored
[ Upstream commit 550da24f ] break_stripe_batch_list breaks up a batch and copies some flags from the batch head to the members, preserving others. It doesn't preserve or copy STRIPE_PREREAD_ACTIVE. This is not normally a problem as STRIPE_PREREAD_ACTIVE is cleared when a stripe_head is added to a batch, and is not set on stripe_heads already in a batch. However there is no locking to ensure one thread doesn't set the flag after it has just been cleared in another. This does occasionally happen. md/raid5 maintains a count of the number of stripe_heads with STRIPE_PREREAD_ACTIVE set: conf->preread_active_stripes. When break_stripe_batch_list clears STRIPE_PREREAD_ACTIVE inadvertently this could becomes incorrect and will never again return to zero. md/raid5 delays the handling of some stripe_heads until preread_active_stripes becomes zero. So when the above mention race happens, those stripe_heads become blocked and never progress, resulting is write to the array handing. So: change break_stripe_batch_list to preserve STRIPE_PREREAD_ACTIVE in the members of a batch. URL: https://bugzilla.kernel.org/show_bug.cgi?id=108741 URL: https://bugzilla.redhat.com/show_bug.cgi?id=1258153 URL: http://thread.gmane.org/5649C0E9.2030204@zoner.cz Reported-by: Martin Svec <martin.svec@zoner.cz> (and others) Tested-by:
Tom Weber <linux@junkyard.4t2.com> Fixes: 1b956f7a ("md/raid5: be more selective about distributing flags across batch.") Cc: stable@vger.kernel.org (v4.1 and later) Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Maurizio Lombardi authored
[ Upstream commit 84bd6499 ] In beiscsi_setup_boot_info(), the boot_kset pointer should be set to NULL in case of failure otherwise an invalid pointer dereference may occur later. Cc: <stable@vger.kernel.org> Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Jitendra Bhivare <jitendra.bhivare@broadcom.com> Signed-off-by:
-
Bjorn Helgaas authored
[ Upstream commit b8941571 ] The Home Agent and PCU PCI devices in Broadwell-EP have a non-BAR register where a BAR should be. We don't know what the side effects of sizing the "BAR" would be, and we don't know what address space the "BAR" might appear to describe. Mark these devices as having non-compliant BARs so the PCI core doesn't touch them. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Tested-by:
Andi Kleen <ak@linux.intel.com> CC: stable@vger.kernel.org Signed-off-by:
-
