Convert orion_wdt driver to use watchdog framework API.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

module_platform_driver() replaces module_init() and module_exit()
and makes the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Some motherboards like the Advantech ARK3400 documentation
use a non-inverted GPIO pin. We fix this by assuming that
the BIOS will set the Polarity bit for the GPIO correctly
at startup and we keep the Bit-setting intact when we start
and stop the watchdog.
Reported-by: Jean-François Deverge <jf.deverge@gmail.com>
Signed-off-by: Dave Mueller <d.mueller@elsoft.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

OMAP watchdog driver is adapted to runtime PM like a general device
driver but it is not appropriate. It is causing couple of functional
issues.

1. On OMAP4 SYSCLK can't be gated, because of issue with WDTIMER2 module,
which constantly stays in "in transition" state. Value of register
CM_WKUP_WDTIMER2_CLKCTRL is always 0x00010000 in this case.
Issue occurs immediately after first idle, when hwmod framework tries
to disable WDTIMER2 functional clock - "wd_timer2_fck". After this
module falls to "in transition" state, and SYSCLK gating is blocked.

2. Due to runtime PM, watchdog timer may be completely disabled.
In current code base watchdog timer is not disabled only because of
issue 1. Otherwise state of WDTIMER2 module will be "Disabled", and there
will be no interrupts from omap_wdt. In other words watchdog will not
work at all.

Watchdong is a special IP and it should not be disabled otherwise
purpose of it itself is defeated. Watchdog functional clock should
never be disabled. This patch updates the runtime PM handling in
driver so that runtime PM is limited only during probe/shutdown
and suspend/resume.

The patch fixes issue 1 and 2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

ie6xx_wdt_probe() calls ie6xx_wdt_debugfs_exit() as part of
it's error cleanup path, and ie6xx_wdt_debugfs_exit() is
currently annotated __devexit.
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

bcm63xx_wdt was used as a platform_driver but was not suffixed with
_driver, thus causing section mismatches, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This patch converts the iTCO_wdt watchdog driver to use the
generic watchdog framework.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This watchdog driver had ioctl defines introduced locally
for pre timeout handling, marked to be removed as soon as
a generic replacement would become available.

The latter has actually occurred in 2006, at e05b59fe.

Remove the local duplicates for pre timeout handling.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Do not use clock-frequency property from parent node.
Use it from watchdog node.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-By: Alejandro Cabrera <acabrera@udio.cujae.edu.cu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Make sure we prepare/unprepare the COH901327 watchdog timer
as is required by the clk API especially if you use common
clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by : Pankaj Jangra <jangra.pankaj9@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The Jetway JNF99 motherboard features a F71869 SuperIO chip, but its
watchdog chipset ID appears to be 1007 (as opposed to 0814).  Some testing
confirmed it behaves the exact same as 0814. So add this chipset ID to the
module's ID list so that the Fintek watchdog driver can correctly identify
and access it.
Signed-off-by: Justin Wheeler <jwheeler@datademons.com>
Acked-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull MMC updates from Chris Ball:
 "MMC highlights for 3.6:

  Core:
   - Rename cd-gpio to slot-gpio and extend it to support more slot GPIO
     functions, such as write-protect.
   - Add a function to get regulators (Vdd and Vccq) for a host.

  Drivers:
   - sdhci-pxav2, sdhci-pxav3: Add device tree support.
   - sdhi: Add device tree support.
   - sh_mmcif: Add support for regulators, device tree, slot-gpio.
   - tmio: Add regulator support, use slot-gpio."

* tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (62 commits)
  mmc: sdhci-dove: Prepare for common clock framework
  mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BIT
  mmc: omap_hsmmc: ensure probe returns error upon resource failure
  mmc: mxs-mmc: Add wp-inverted property
  mmc: esdhc: Fix DMA_MASK to not break mx25 DMA access
  mmc: core: reset signal voltage on power up
  mmc: sd: Fix sd current limit setting
  mmc: omap_hsmmc: add clk_prepare and clk_unprepare
  mmc: sdhci: When a UHS switch fails, cycle power if regulator is used
  mmc: atmel-mci: modify CLKDIV displaying in debugfs
  mmc: atmel-mci: fix incorrect setting of host->data to NULL
  mmc: sdhci: poll for card even when card is logically unremovable
  mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER
  mmc: sdio: Change pr_warning to pr_warn_ratelimited
  mmc: core: Simplify and fix for SD switch processing
  mmc: sdhci: restore host settings when card is removed
  mmc: sdhci: fix incorrect command used in tuning
  mmc: sdhci-pci: CaFe has broken card detection
  mmc: sdhci: Report failure reasons for all cases in sdhci_add_host()
  mmc: s3cmci: Convert s3cmci driver to gpiolib API
  ...

Pull x86/mce changes from Ingo Molnar:
 "This tree improves the AMD thresholding bank code and includes a
  memory fault signal handling fixlet."

* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix siginfo_t->si_addr value for non-recoverable memory faults
  x86, MCE, AMD: Update copyrights and boilerplate
  x86, MCE, AMD: Give proper names to the thresholding banks
  x86, MCE, AMD: Make error_count read only
  x86, MCE, AMD: Cleanup reading of error_count
  x86, MCE, AMD: Print decimal thresholding values
  x86, MCE, AMD: Move shared bank to node descriptor
  x86, MCE, AMD: Remove local_allocate_... wrapper
  x86, MCE, AMD: Remove shared banks sysfs linking
  x86, amd_nb: Export model 0x10 and later PCI id

As mach-dove is moving towards common clock framework prepare
the sdhci driver to grab its clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The sdio controller on dove doesn't have a bit to indicate
high-speed. With the quirk set it fixes accessing high-speed
sdcards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

If platform_get_resource_by_name() fails, driver probe is aborted an
should return an error so the driver is not bound to the device.

However, in the current error path of platform_get_resource_by_name(),
probe returns zero since the return value (ret) is not properly set.
With a zero return value, the driver core assumes probe was successful
and will bind the driver to the device.

Fix this by ensuring that probe returns an error code in this failure
path.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The write-protect GPIO is inverted on some boards. Handle such case.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Patch to not set reserved bits in i.MX25 PROCTL register.  DMA stops
working if those bits get set.
Signed-off-by: Wilson Callan <wilson.callan@savantsystems.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

Pull power management updates from Rafael Wysocki:

 - ACPI conversion to PM handling based on struct dev_pm_ops.
 - Conversion of a number of platform drivers to PM handling based on
   struct dev_pm_ops and removal of empty legacy PM callbacks from a
   couple of PCI drivers.
 - Suspend-to-both for in-kernel hibernation from Bojan Smojver.
 - cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti
   Murthy.
 - cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
 - Suspend and hibernate fixes from Srivatsa Bhat and Colin Cross.
 - Generic PM domains framework updates.
 - RTC CMOS wakeup signaling update from Paul Fox.
 - sparse warnings fixes from Sachin Kamat.
 - Build warnings fixes for the generic PM domains framework and PM
   sysfs code.
 - sysfs switch for printing device suspend times from Sameer Nanda.
 - Documentation fix from Oskar Schirmer.

* tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
  cpufreq: Fix sysfs deadlock with concurrent hotplug/frequency switch
  EXYNOS: bugfix on retrieving old_index from freqs.old
  PM / Sleep: call early resume handlers when suspend_noirq fails
  PM / QoS: Use NULL pointer instead of plain integer in qos.c
  PM / QoS: Use NULL pointer instead of plain integer in pm_qos.h
  PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
  PM / Sleep: Add missing static storage class specifiers in main.c
  cpuilde / ACPI: remove time from acpi_processor_cx structure
  cpuidle / ACPI: remove usage from acpi_processor_cx structure
  cpuidle / ACPI : remove latency_ticks from acpi_processor_cx structure
  rtc-cmos: report wakeups from interrupt handler
  PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
  PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
  olpc-xo15-sci: Use struct dev_pm_ops for power management
  PM / Domains: Replace plain integer with NULL pointer in domain.c file
  PM / Domains: Add missing static storage class specifier in domain.c file
  PM / crypto / ux500: Use struct dev_pm_ops for power management
  PM / IPMI: Remove empty legacy PCI PM callbacks
  tpm_nsc: Use struct dev_pm_ops for power management
  tpm_tis: Use struct dev_pm_ops for power management
  ...

Pull target updates from Nicholas Bellinger:
 "There have been lots of work in a number of areas this past round.
  The highlights include:

   - Break out target_core_cdb.c emulation into SPC/SBC ops (hch)
   - Add a parse_cdb method to target backend drivers (hch)
   - Move sync_cache + write_same + unmap into spc_ops (hch)
   - Use target_execute_cmd for WRITEs in iscsi_target + srpt (hch)
   - Offload WRITE I/O backend submission in tcm_qla2xxx + tcm_fc (hch +
     nab)
   - Refactor core_update_device_list_for_node() into enable/disable
     funcs (agrover)
   - Replace the TCM processing thread with a TMR work queue (hch)
   - Fix regression in transport_add_device_to_core_hba from TMR
     conversion (DanC)
   - Remove racy, now-redundant check of sess_tearing_down with qla2xxx
     (roland)
   - Add range checking, fix reading of data len + possible underflow in
     UNMAP (roland)
   - Allow for target_submit_cmd() returning errors + convert fabrics
     (roland + nab)
   - Drop bogus struct file usage for iSCSI/SCTP (viro)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (54 commits)
  iscsi-target: Drop bogus struct file usage for iSCSI/SCTP
  target: NULL dereference on error path
  target: Allow for target_submit_cmd() returning errors
  target: Check number of unmap descriptors against our limit
  target: Fix possible integer underflow in UNMAP emulation
  target: Fix reading of data length fields for UNMAP commands
  target: Add range checking to UNMAP emulation
  target: Add generation of LOGICAL BLOCK ADDRESS OUT OF RANGE
  target: Make unnecessarily global se_dev_align_max_sectors() static
  target: Remove se_session.sess_wait_list
  qla2xxx: Remove racy, now-redundant check of sess_tearing_down
  target: Check sess_tearing_down in target_get_sess_cmd()
  sbp-target: Consolidate duplicated error path code in sbp_handle_command()
  target: Un-export target_get_sess_cmd()
  qla2xxx: Get rid of redundant qla_tgt_sess.tearing_down
  target: Make core_disable_device_list_for_node use pre-refactoring lock ordering
  target: refactor core_update_device_list_for_node()
  target: Eliminate else using boolean logic
  target: Misc retval cleanups
  target: Remove hba param from core_dev_add_lun
  ...

Pull regulator updates from Mark Brown:
 "Lots and lots of fixes from Axel and some others here, plus some
  framework enhancements which continue the theme of factoring code out
  of the drivers and into the core.

   - Initial framework support for GPIO controlled enable signals,
     saving a bunch of code in drivers.
   - Move fixed regulator enable time and voltage mapping table
     specifications to data.
   - Used some of the recent framework enhancements to make voltage
     change notifications more useful, passing the voltage in as an
     argument to the notification.
   - Fixed the pattern used for finding individual regulators on a
     device to not rely on the node name, supporting the use of multiple
     PMICs of the same type in the system.
   - New drivers for Maxim MAX77686, TI LP872x and LP8788, Samsung
     S2MPS11, and Wolfson Arizona microphone supplies and LDOs."

* tag 'regulator-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (176 commits)
  regulator: add new lp8788 regulator driver
  regulator: mc13xxx: Remove extern function declaration for mc13xxx_sw_regulator
  regulator: tps65910: set input_supply on desc unconditionally
  regulator: palmas: Fix calcuating selector in palmas_map_voltage_smps
  regulator: lp872x: Simplify implementation of lp872x_find_regulator_init_data()
  regulator: twl: Fix list_voltate for twl6030ldo_ops
  regulator: twl: Convert twl6030ldo_ops to [get|set]_voltage_sel
  regulator: twl: Fix the formula to calculate vsel and voltage for twl6030ldo
  regulator: s5m8767: Properly handle gpio_request failure
  regulator: max8997: Properly handle gpio_request failure
  regulator: tps62360: use devm_* for gpio request
  regulator: tps6586x: add support for input supply
  regulator: tps65217: Add device tree support
  regulator: aat2870: Remove unused min_uV and max_uV from struct aat2870_regulator
  regulator: aat2870: Convert to regulator_list_voltage_table
  regulator: da9052: initialize of_node param for regulator register
  regulator: Add REGULATOR_STATUS_UNDEFINED.
  regulator: Fix a typo in regulator_mode_to_status() core function.
  regulator: s2mps11: Use sec_reg_write rather than sec_reg_update when mask is 0xff
  regulator: s2mps11: Fix wrong setting for config.dev
  ...

Pull regmap updates from Mark Brown:
 "A few fixes plus a few features, the most generally useful thing being
  the register paging support which can be used by quite a few devices:

   - Support for wake IRQs in regmap-irq
   - Support for register paging
   - Support for explicitly specified endianness, mostly for MMIO."

* tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Fix incorrect arguments to kzalloc() call
  regmap: Add hook for printk logging for debugging during early init
  regmap: Fix work_buf switching for page update during virtual range access.
  regmap: Add support for register indirect addressing.
  regmap: Move lock out from internal function _regmap_update_bits().
  regmap: mmio: Staticize regmap_mmio_gen_context()
  regmap: Remove warning on stubbed dev_get_regmap()
  regmap: Implement support for wake IRQs
  regmap: Don't try to map non-existant IRQs
  regmap: Constify regmap_irq_chip
  regmap: mmio: request native endian formatting
  regmap: allow busses to request formatting with specific endianness

Pull a x86/build change from Ingo Molnar.

This makes the default stack alignment on x86-64 be just 8, allowing for
improved code generation (it can avoid some unnecessary extra alignment
logic and use just pure push/pop sequences) and smaller stack frames.

We can't generally do SSE with 16-byte alignment issues in the kernel anyway.

* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-64, gcc: Use -mpreferred-stack-boundary=3 if supported

Pull x86/uv changes from Ingo Molnar:
 "UV2 BAU productization fixes.

  The BAU (Broadcast Assist Unit) is SGI's fancy out of line way on UV
  hardware to do TLB flushes, instead of the normal APIC IPI methods.
  The commits here fix / work around hangs in their latest hardware
  iteration (UV2).

  My understanding is that the main purpose of the out of line
  signalling channel is to improve scalability: the UV APIC hardware
  glue does not handle broadcasting to many CPUs very well, and this
  matters most for TLB shootdowns.

  [ I don't agree with all aspects of the current approach: in hindsight
    it would have been better to link the BAU at the IPI/APIC driver
    level instead of the TLB shootdown level, where TLB flushes are
    really just one of the uses of broadcast SMP messages.  Doing that
    would improve scalability in some other ways and it would also
    remove a few uglies from the TLB path.  It would also be nice to
    push more is_uv_system() tests into proper x86_init or x86_platform
    callbacks.  Cliff? ]"

* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/uv: Work around UV2 BAU hangs
  x86/uv: Implement UV BAU runtime enable and disable control via /proc/sgi_uv/
  x86/uv: Fix the UV BAU destination timeout period

Add a call to mmc_set_signal_voltage() to set signal voltage to 3.3v in
mmc_power_up so that we do not need to touch signal voltage setting in
mmc/sd/sdio init functions and rescan function.

For mmc/sd cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will lose its power and when powered on again, we
will set signal voltage to 3.3v in mmc_power_up before its resume function
gets called, which will re-init the card.

And for sdio cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will either lose its power or not depending on if it
wants to wakeup the host. If power is not maintained, it is the same case as
mmc/sd cards. If power is maintained, mmc_power_up will not be called and
the card's signal voltage will remain at the last setting.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Host has different current capabilities at different voltages, we need
to record these settings seperately. The defined voltages are 1.8/3.0/3.3.
For other voltages, we do not touch current limit setting.

Before we set the current limit for the sd card, find out the host's
operating voltage first and then find out the current capabilities of
the host at that voltage to set the current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

In preparation for OMAP moving to the Common Clock Framework (CCF)
add clk_prepare() and clk_unprepare() for the hsmmc clocks.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Power needs to be removed from the card when switching to 1.8v fails.

If a regulator is used to control vmmc we need to turn the
regulator off and then back on otherwise power will not be
removed from the card.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Modify clock division displaying in debugfs for matching
the new CLKDIV,CLKODD user interface arrangement.
Is using the has_odd_clk_div property to choose the proper format.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Setting host->data to NULL is incorrect sequence in STATE_SENDING_STOP
state of FSM: This early setting leads to the skip of dma_unmap_sg()
in atmci_dma_cleanup() which is a bug.

Idea taken from dw_mmc by Seungwon Jeon.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The Marvell CaFe is now marked as having bad card detection to fix
a problem during system resume.

Now on the OLPC XO-1 we are facing the issue that the card is marked
as logically unremovable (via MMC_UNSAFE_RESUME), which means that
mmc_card_is_removable considers the card non-removable. The existing
code logic decides not to poll for card presence in this case, and
card detection is also disabled because of the quirk being set.
This means that no SD cards are detected when inserted after boot.

Refine the logic to enable card presence polling in the case when
a card is logically unremovable, only avoiding the poll in the case
when the card is physically non-removable (denoted with
MMC_CAP_NONREMOVABLE).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

Add a new flag of SDHCI_USING_RETUNING_TIMER to represent if the host
is using a retuning timer for the card inserted.

This flag is set when the host does tuning the first time for the card
and the host's retuning mode is 1. This flag is used afterwards whenever
needs to decide if the host is currently using a retuning timer.

This flag is cleared when the card is removed in sdhci_reinit.

The set/clear of the flag and the start/stop of the retuning timer is
associated with the card's init/remove time, so there is no need to
touch it when the host is to be removed as at that time the card should
have already been removed.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

When debugging one bad issue, got lots of pr_warning messages
"queuing unknown CIS tuple" which caused a printk storm and
flooded the console.

This patch changes the pr_warning to use pr_warn_ratelimited.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Pull x86/reboot changes from Ingo Molnar:
 "Now that the revampted x86 real-mode trampoline code is upstream and
  seems to be working well, we can extend the 64-bit reboot code to be
  as capable as the 32-bit one."

* 'x86-reboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-64, reboot: Be more paranoid in 64-bit reboot=bios
  x86, reboot: Drop redundant write of reboot_mode
  x86-64, reboot: Allow reboot=bios and reboot-cpu override on x86-64

In mmc_read_switch, just do a one time mode 0 switch command to get the
support bits information, no need to do multiple times as the support
bits do not change with different arguments.

And no need to check current limit support bits, as these bits are
fixed according to the signal voltage. If the signal voltage is 1.8V,
the support bits would be 0xf and if the signal voltage is 3.3V, the
support bits would be 0x01. We will check host's ability to set the
current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Some of the host settings are affected by different cards inserted, e.g.
when an UHS-I card is inserted, the SDHCI_NEEDS_RETUING flag might be
set when the tuning timer expired and host's max_blk_count will be
reduced to make sure the data transfer for a command does not exceed 4MiB
to meet the retuning mode 1's requirement.

When the card is removed, we should restore the original setting of the
host since we can't be sure the next card being inserted will still be
an UHS-I card that needs tuning. The original setting include its
max_blk_count and no set of the flag of SDHCI_NEEDS_RETUNING.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

For SD hosts using retuning mode 1, when retuning timer expired, it will
need to do retuning in sdhci_request before processing the actual
request. But the retuning command is fixed: cmd19 for SD card and cmd21
for eMMC card, so we can't use the original request's command to do the
tuning.

And since the tuning command depends on the card type attached to the
host, we will need to know the card type to use the correct tuning
command.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Cc: stable <stable@vger.kernel.org> [3.3+]
Signed-off-by: Chris Ball <cjb@laptop.org>

At http://dev.laptop.org/ticket/11980 we have determined that the
Marvell CaFe SDHCI controller reports bad card presence during
resume. It reports that no card is present even when it is.
This is a regression -- resume worked back around 2.6.37.

Around 400ms after resuming, a "card inserted" interrupt is
generated, at which point it starts reporting presence.

Work around this hardware oddity by setting the
SDHCI_QUIRK_BROKEN_CARD_DETECTION flag.
Thanks to Chris Ball for helping with diagnosis.
Signed-off-by: Daniel Drake <dsd@laptop.org>
[stable@: please apply to 3.0+]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

For most error conditions sdhci_add_host() will print a diagnostic
message indicating why it failed but there are a few cases where this
does not happen. Add error messages in these cases to aid diagnosis.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The s3c2410_gpio* calls are obsolete and have been scheduled for
removal since several kernel releases. Remove them and use common
gpiolib API.

This patch is a prerequisite for removal of the S3C24XX SoC specific
arch/arm/plat-samsung/include/gpio-fns.h header.

Tested on Micro2440-SDK.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>