During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped.  This is correct because a FW reset during
ifdown will clear these register mappings.  If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.

But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.

Fixes: 8cc95ceb ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked.  Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.

Fixes: 7d2837dd ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test.  This
scheme fails sometime if the port is shared with management firmware
that can also send packets.  The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.

Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address.  This should
filter out other packets sent by management firmware.

Fixes: 91725d89 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For offline (destructive) self tests, we need to stop the RDMA driver
first.  Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.

The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.

Fixes: 55fd0cf3 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None.  Fix it to properly return
ETHTOOL_FEC_OFF in that case.

Fixes: 8b277589 ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the DSA master doesn't support IFF_UNICAST_FLT, then the following
call path is possible:

dsa_slave_switchdev_event_work
-> dsa_port_host_fdb_add
   -> dev_uc_add
      -> __dev_set_rx_mode
         -> __dev_set_promiscuity

Since the blamed commit, dsa_slave_switchdev_event_work() no longer
holds rtnl_lock(), which triggers the ASSERT_RTNL() from
__dev_set_promiscuity().

Taking rtnl_lock() around dev_uc_add() is impossible, because all the
code paths that call dsa_flush_workqueue() do so from contexts where the
rtnl_mutex is already held - so this would lead to an instant deadlock.

dev_uc_add() in itself doesn't require the rtnl_mutex for protection.
There is this comment in __dev_set_rx_mode() which assumes so:

		/* Unicast addresses changes may only happen under the rtnl,
		 * therefore calling __dev_set_promiscuity here is safe.
		 */

but it is from commit 4417da66 ("[NET]: dev: secondary unicast
address support") dated June 2007, and in the meantime, commit
f1f28aa3 ("netdev: Add addr_list_lock to struct net_device."), dated
July 2008, has added &dev->addr_list_lock to protect this instead of the
global rtnl_mutex.

Nonetheless, __dev_set_promiscuity() does assume rtnl_mutex protection,
but it is the uncommon path of what we typically expect dev_uc_add()
to do. So since only the uncommon path requires rtnl_lock(), just check
ahead of time whether dev_uc_add() would result into a call to
__dev_set_promiscuity(), and handle that condition separately.

DSA already configures the master interface to be promiscuous if the
tagger requires this. We can extend this to also cover the case where
the master doesn't handle dev_uc_add() (doesn't support IFF_UNICAST_FLT),
and on the premise that we'd end up making it promiscuous during
operation anyway, either if a DSA slave has a non-inherited MAC address,
or if the bridge notifies local FDB entries for its own MAC address, the
address of a station learned on a foreign port, etc.

Fixes: 0faf890f ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b3612ccd ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.

After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.

Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.

Fixes: b3612ccd ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

All functions defined as static inline in net/checksum.h are
meant to be inlined for performance reason.

But since commit ac7c3e4f ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly") the compiler is allowed to
uninline functions when it wants.

Fair enough in the general case, but for tiny performance critical
checksum helpers that's counter-productive.

The problem mainly arises when selecting CONFIG_CC_OPTIMISE_FOR_SIZE,
Those helpers being 'static inline' in header files you suddenly find
them duplicated many times in the resulting vmlinux.

Here is a typical exemple when building powerpc pmac32_defconfig
with CONFIG_CC_OPTIMISE_FOR_SIZE. csum_sub() appears 4 times:

	c04a23cc <csum_sub>:
	c04a23cc:	7c 84 20 f8 	not     r4,r4
	c04a23d0:	7c 63 20 14 	addc    r3,r3,r4
	c04a23d4:	7c 63 01 94 	addze   r3,r3
	c04a23d8:	4e 80 00 20 	blr
		...
	c04a2ce8:	4b ff f6 e5 	bl      c04a23cc <csum_sub>
		...
	c04a2d2c:	4b ff f6 a1 	bl      c04a23cc <csum_sub>
		...
	c04a2d54:	4b ff f6 79 	bl      c04a23cc <csum_sub>
		...
	c04a754c <csum_sub>:
	c04a754c:	7c 84 20 f8 	not     r4,r4
	c04a7550:	7c 63 20 14 	addc    r3,r3,r4
	c04a7554:	7c 63 01 94 	addze   r3,r3
	c04a7558:	4e 80 00 20 	blr
		...
	c04ac930:	4b ff ac 1d 	bl      c04a754c <csum_sub>
		...
	c04ad264:	4b ff a2 e9 	bl      c04a754c <csum_sub>
		...
	c04e3b08 <csum_sub>:
	c04e3b08:	7c 84 20 f8 	not     r4,r4
	c04e3b0c:	7c 63 20 14 	addc    r3,r3,r4
	c04e3b10:	7c 63 01 94 	addze   r3,r3
	c04e3b14:	4e 80 00 20 	blr
		...
	c04e5788:	4b ff e3 81 	bl      c04e3b08 <csum_sub>
		...
	c04e65c8:	4b ff d5 41 	bl      c04e3b08 <csum_sub>
		...
	c0512d34 <csum_sub>:
	c0512d34:	7c 84 20 f8 	not     r4,r4
	c0512d38:	7c 63 20 14 	addc    r3,r3,r4
	c0512d3c:	7c 63 01 94 	addze   r3,r3
	c0512d40:	4e 80 00 20 	blr
		...
	c0512dfc:	4b ff ff 39 	bl      c0512d34 <csum_sub>
		...
	c05138bc:	4b ff f4 79 	bl      c0512d34 <csum_sub>
		...

Restore the expected behaviour by using __always_inline for all
functions defined in net/checksum.h

vmlinux size is even reduced by 256 bytes with this patch:

	   text	   data	    bss	    dec	    hex	filename
	6980022	2515362	 194384	9689768	 93daa8	vmlinux.before
	6979862	2515266	 194384	9689512	 93d9a8	vmlinux.now

Fixes: ac7c3e4f ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-02-18

This series contains updates to ice driver only.

Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.

Michal removes accidental unconditional setting of l4 port filtering
flag.

Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.

Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Fix address advertisement races and stabilize tests

Patches 1, 2, and 7 modify two self tests to give consistent, accurate
results by fixing timing issues and accounting for syncookie behavior.

Paches 3-6 fix two races in overlapping address advertisement send and
receive. Associated self tests are updated, including addition of two
MIBs to enable testing and tracking dropped address events.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 2843ff6f ("mptcp: remote addresses fullmesh"), an
MPTCP client can attempt creating multiple MPJ subflow simultaneusly.

In such scenario the server, when syncookies are enabled, could end-up
accepting incoming MPJ syn even above the configured subflow limit, as
the such limit can be enforced in a reliable way only after the subflow
creation. In case of syncookie, only after the 3rd ack reception.

As a consequence the related self-tests case sporadically fails, as it
verify that the server always accept the expected number of MPJ syn.

Address the issues relaxing the MPJ syn number constrain. Note that the
check on the accepted number of MPJ 3rd ack still remains intact.

Fixes: 2843ff6f ("mptcp: remote addresses fullmesh")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The in kernel MPTCP PM implementation can process a single
incoming add address option at any given time. In the
mentioned test the server can surpass such limit. Let the
setup cope with that allowing a faster add_addr retransmission.

Fixes: a88c9e49 ("mptcp: do not block subflows creation on errors")
Fixes: f7efc777 ("mptcp: drop argument port from mptcp_pm_announce_addr")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/254Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.

The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.

This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.

Fixes: f7efc777 ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.

Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.

Fixes: f7efc777 ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit a88c9e49 ("mptcp: do not block subflows
creation on errors"), if a signal address races with a failing
subflow creation, the subflow creation failure control path
can trigger the selection of the next address to be announced
while the current announced is still pending.

The above will cause the unintended suppression of the ADD_ADDR
announce.

Fix the issue skipping the to-be-suppressed announce before it
will mark an endpoint as already used. The relevant announce
will be triggered again when the current one will complete.

Fixes: a88c9e49 ("mptcp: do not block subflows creation on errors")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mentioned test has to wait for a subflow creation failure.
The current code looks for TCP sockets in TW state and sometimes
misses the relevant event. Switch to a more stable check, looking
for the associated mib counter.

Fixes: 46e967d1 ("selftests: mptcp: add tests for subflow creation failure")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/257Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of waiting for an arbitrary amount of time for the MPTCP
MP_CAPABLE handshake to complete, explicitly wait for the relevant
socket to enter into the established status.

Additionally let the data transfer application use the slowest
transfer mode available (-r), to cope with very slow host, or
high jitter caused by hosting VMs.

Fixes: df62f2ec ("selftests/mptcp: add diag interface tests")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/258Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.

In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.

So set it to -1.

Fixes: 20cce886 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Switch to the quicinc.com ids.
Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Link: https://lore.kernel.org/r/1645174218-32632-1-git-send-email-quic_subashab@quicinc.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Booting a MACCHIATObin with 5.17, the system OOPs with
a null pointer deref when the network is started. This
is caused by the pcs->ops structure being null in
mcpp2_acpi_start() when it tries to call pcs_config().

Hoisting the code which sets pcs_gmac.ops and pcs_xlg.ops,
assuring they are always set, fixes the problem.

The OOPs looks like:
[   18.687760] Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000010
[   18.698561] Mem abort info:
[   18.698564]   ESR = 0x96000004
[   18.698567]   EC = 0x25: DABT (current EL), IL = 32 bits
[   18.709821]   SET = 0, FnV = 0
[   18.714292]   EA = 0, S1PTW = 0
[   18.718833]   FSC = 0x04: level 0 translation fault
[   18.725126] Data abort info:
[   18.729408]   ISV = 0, ISS = 0x00000004
[   18.734655]   CM = 0, WnR = 0
[   18.738933] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000111bbf000
[   18.745409] [0000000000000010] pgd=0000000000000000, p4d=0000000000000000
[   18.752235] Internal error: Oops: 96000004 [#1] SMP
[   18.757134] Modules linked in: rfkill ip_set nf_tables nfnetlink qrtr sunrpc vfat fat omap_rng fuse zram xfs crct10dif_ce mvpp2 ghash_ce sbsa_gwdt phylink xhci_plat_hcd ahci_plam
[   18.773481] CPU: 0 PID: 681 Comm: NetworkManager Not tainted 5.17.0-0.rc3.89.fc36.aarch64 #1
[   18.781954] Hardware name: Marvell                         Armada 7k/8k Family Board      /Armada 7k/8k Family Board      , BIOS EDK II Jun  4 2019
[   18.795222] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   18.802213] pc : mvpp2_start_dev+0x2b0/0x300 [mvpp2]
[   18.807208] lr : mvpp2_start_dev+0x298/0x300 [mvpp2]
[   18.812197] sp : ffff80000b4732c0
[   18.815522] x29: ffff80000b4732c0 x28: 0000000000000000 x27: ffffccab38ae57f8
[   18.822689] x26: ffff6eeb03065a10 x25: ffff80000b473a30 x24: ffff80000b4735b8
[   18.829855] x23: 0000000000000000 x22: 00000000000001e0 x21: ffff6eeb07b6ab68
[   18.837021] x20: ffff6eeb07b6ab30 x19: ffff6eeb07b6a9c0 x18: 0000000000000014
[   18.844187] x17: 00000000f6232bfe x16: ffffccab899b1dc0 x15: 000000006a30f9fa
[   18.851353] x14: 000000003b77bd50 x13: 000006dc896f0e8e x12: 001bbbfccfd0d3a2
[   18.858519] x11: 0000000000001528 x10: 0000000000001548 x9 : ffffccab38ad0fb0
[   18.865685] x8 : ffff80000b473330 x7 : 0000000000000000 x6 : 0000000000000000
[   18.872851] x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff80000b4732f8
[   18.880017] x2 : 000000000000001a x1 : 0000000000000002 x0 : ffff6eeb07b6ab68
[   18.887183] Call trace:
[   18.889637]  mvpp2_start_dev+0x2b0/0x300 [mvpp2]
[   18.894279]  mvpp2_open+0x134/0x2b4 [mvpp2]
[   18.898483]  __dev_open+0x128/0x1e4
[   18.901988]  __dev_change_flags+0x17c/0x1d0
[   18.906187]  dev_change_flags+0x30/0x70
[   18.910038]  do_setlink+0x278/0xa7c
[   18.913540]  __rtnl_newlink+0x44c/0x7d0
[   18.917391]  rtnl_newlink+0x5c/0x8c
[   18.920892]  rtnetlink_rcv_msg+0x254/0x314
[   18.925006]  netlink_rcv_skb+0x48/0x10c
[   18.928858]  rtnetlink_rcv+0x24/0x30
[   18.932449]  netlink_unicast+0x290/0x2f4
[   18.936386]  netlink_sendmsg+0x1d0/0x41c
[   18.940323]  sock_sendmsg+0x60/0x70
[   18.943825]  ____sys_sendmsg+0x248/0x260
[   18.947762]  ___sys_sendmsg+0x74/0xa0
[   18.951438]  __sys_sendmsg+0x64/0xcc
[   18.955027]  __arm64_sys_sendmsg+0x30/0x40
[   18.959140]  invoke_syscall+0x50/0x120
[   18.962906]  el0_svc_common.constprop.0+0x4c/0xf4
[   18.967629]  do_el0_svc+0x30/0x9c
[   18.970958]  el0_svc+0x28/0xb0
[   18.974025]  el0t_64_sync_handler+0x10c/0x140
[   18.978400]  el0t_64_sync+0x1a4/0x1a8
[   18.982078] Code: 52800004 b9416262 aa1503e0 52800041 (f94008a5)
[   18.988196] ---[ end trace 0000000000000000 ]---

Fixes: cff05632 ("net: mvpp2: use .mac_select_pcs() interface")
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220214231852.3331430-1-jeremy.linton@arm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
  assignment is an uninitialized value. The computed value will
  also be garbage
  ldo->phy_type_low |= ((u64)buf << (i * 16));
  ~~~~~~~~~~~~~~~~~ ^

When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv.  So initialize.

Fixes: ea78ce4d ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Clang static analysis reports this issue
time64.h:69:50: warning: The left operand of '+'
  is a garbage value
  set_normalized_timespec64(&ts_delta, lhs.tv_sec + rhs.tv_sec,
                                       ~~~~~~~~~~ ^
In ice_ptp_adjtime_nonatomic(), the timespec64 variable 'now'
is set by ice_ptp_gettimex64().  This function can fail
with -EBUSY, so 'now' can have a gargbage value.
So check the return.

Fixes: 06c16d89 ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Commit c503e632 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.

This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.

It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.

Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.

Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.

This locking change also fixes the root cause originally fixed by commit
c503e632 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.

Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.

Fixes: c503e632 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Accidentally filter flag for none encapsulated l4 port field is always
set. Even if user wants to add encapsulated l4 port field.

Remove this unnecessary flag setting.

Fixes: 9e300987 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In switchdev mode, slow-path rules need to match all protocols, in order
to correctly redirect unfiltered or missed packets to the uplink. To set
this up for the virtual function to uplink flow, the rule that redirects
packets to the control VSI must have the tunnel type set to
ICE_SW_TUN_AND_NON_TUN. As a result of that new tunnel type being set,
ice_get_compat_fv_bitmap will select ICE_PROF_ALL. At that point all
profiles would be selected for this rule, resulting in the desired
behavior. Without this change slow-path would not work with
tunnel protocols.

Fixes: 8b032a55 ("ice: low level support for tunnels")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.

Fixes: f14f5c11 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

UDP sendmsg() can be lockless, this is causing all kinds
of data races.

This patch converts sk->sk_tskey to remove one of these races.

BUG: KCSAN: data-race in __ip_append_data / __ip_append_data

read to 0xffff8881035d4b6c of 4 bytes by task 8877 on cpu 1:
 __ip_append_data+0x1c1/0x1de0 net/ipv4/ip_output.c:994
 ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
 udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

write to 0xffff8881035d4b6c of 4 bytes by task 8880 on cpu 0:
 __ip_append_data+0x1d8/0x1de0 net/ipv4/ip_output.c:994
 ip_make_skb+0x13f/0x2d0 net/ipv4/ip_output.c:1636
 udp_sendmsg+0x12bd/0x14c0 net/ipv4/udp.c:1249
 inet_sendmsg+0x5f/0x80 net/ipv4/af_inet.c:819
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmmsg+0x267/0x4c0 net/socket.c:2553
 __do_sys_sendmmsg net/socket.c:2582 [inline]
 __se_sys_sendmmsg net/socket.c:2579 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2579
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x0000054d -> 0x0000054e

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8880 Comm: syz-executor.5 Not tainted 5.17.0-rc2-syzkaller-00167-gdcb85f85-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 09c2d251 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).

To fix the above, remove these unneccary checks in flow
table lookup.

Fixes: 46475bb2 ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When bringing down the netdevice or system shutdown, a panic can be
triggered while accessing the sysfs path because the device is already
removed.

    [  755.549084] mlx5_core 0000:12:00.1: Shutdown was called
    [  756.404455] mlx5_core 0000:12:00.0: Shutdown was called
    ...
    [  757.937260] BUG: unable to handle kernel NULL pointer dereference at           (null)
    [  758.031397] IP: [<ffffffff8ee11acb>] dma_pool_alloc+0x1ab/0x280

    crash> bt
    ...
    PID: 12649  TASK: ffff8924108f2100  CPU: 1   COMMAND: "amsd"
    ...
     #9 [ffff89240e1a38b0] page_fault at ffffffff8f38c778
        [exception RIP: dma_pool_alloc+0x1ab]
        RIP: ffffffff8ee11acb  RSP: ffff89240e1a3968  RFLAGS: 00010046
        RAX: 0000000000000246  RBX: ffff89243d874100  RCX: 0000000000001000
        RDX: 0000000000000000  RSI: 0000000000000246  RDI: ffff89243d874090
        RBP: ffff89240e1a39c0   R8: 000000000001f080   R9: ffff8905ffc03c00
        R10: ffffffffc04680d4  R11: ffffffff8edde9fd  R12: 00000000000080d0
        R13: ffff89243d874090  R14: ffff89243d874080  R15: 0000000000000000
        ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
    #10 [ffff89240e1a39c8] mlx5_alloc_cmd_msg at ffffffffc04680f3 [mlx5_core]
    #11 [ffff89240e1a3a18] cmd_exec at ffffffffc046ad62 [mlx5_core]
    #12 [ffff89240e1a3ab8] mlx5_cmd_exec at ffffffffc046b4fb [mlx5_core]
    #13 [ffff89240e1a3ae8] mlx5_core_access_reg at ffffffffc0475434 [mlx5_core]
    #14 [ffff89240e1a3b40] mlx5e_get_fec_caps at ffffffffc04a7348 [mlx5_core]
    #15 [ffff89240e1a3bb0] get_fec_supported_advertised at ffffffffc04992bf [mlx5_core]
    #16 [ffff89240e1a3c08] mlx5e_get_link_ksettings at ffffffffc049ab36 [mlx5_core]
    #17 [ffff89240e1a3ce8] __ethtool_get_link_ksettings at ffffffff8f25db46
    #18 [ffff89240e1a3d48] speed_show at ffffffff8f277208
    #19 [ffff89240e1a3dd8] dev_attr_show at ffffffff8f0b70e3
    #20 [ffff89240e1a3df8] sysfs_kf_seq_show at ffffffff8eedbedf
    #21 [ffff89240e1a3e18] kernfs_seq_show at ffffffff8eeda596
    #22 [ffff89240e1a3e28] seq_read at ffffffff8ee76d10
    #23 [ffff89240e1a3e98] kernfs_fop_read at ffffffff8eedaef5
    #24 [ffff89240e1a3ed8] vfs_read at ffffffff8ee4e3ff
    #25 [ffff89240e1a3f08] sys_read at ffffffff8ee4f27f
    #26 [ffff89240e1a3f50] system_call_fastpath at ffffffff8f395f92

    crash> net_device.state ffff89443b0c0000
      state = 0x5  (__LINK_STATE_START| __LINK_STATE_NOCARRIER)

To prevent this scenario, we also make sure that the netdevice is present.
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a 6pack device is detaching, the sixpack_close() will act to cleanup
necessary resources. Although del_timer_sync() in sixpack_close()
won't return if there is an active timer, one could use mod_timer() in
sp_xmit_on_air() to wake up timer again by calling userspace syscall such
as ax25_sendmsg(), ax25_connect() and ax25_ioctl().

This unexpected waked handler, sp_xmit_on_air(), realizes nothing about
the undergoing cleanup and may still call pty_write() to use driver layer
resources that have already been released.

One of the possible race conditions is shown below:

      (USE)                      |      (FREE)
ax25_sendmsg()                   |
 ax25_queue_xmit()               |
  ...                            |
  sp_xmit()                      |
   sp_encaps()                   | sixpack_close()
    sp_xmit_on_air()             |  del_timer_sync(&sp->tx_t)
     mod_timer(&sp->tx_t,...)    |  ...
                                 |  unregister_netdev()
                                 |  ...
     (wait a while)              | tty_release()
                                 |  tty_release_struct()
                                 |   release_tty()
    sp_xmit_on_air()             |    tty_kref_put(tty_struct) //FREE
     pty_write(tty_struct) //USE |    ...

The corresponding fail log is shown below:
===============================================================
BUG: KASAN: use-after-free in __run_timers.part.0+0x170/0x470
Write of size 8 at addr ffff88800a652ab8 by task swapper/2/0
...
Call Trace:
  ...
  queue_work_on+0x3f/0x50
  pty_write+0xcd/0xe0pty_write+0xcd/0xe0
  sp_xmit_on_air+0xb2/0x1f0
  call_timer_fn+0x28/0x150
  __run_timers.part.0+0x3c2/0x470
  run_timer_softirq+0x3b/0x80
  __do_softirq+0xf1/0x380
  ...

This patch reorders the del_timer_sync() after the unregister_netdev()
to avoid UAF bugs. Because the unregister_netdev() is well synchronized,
it flushs out any pending queues, waits the refcount of net_device
decreases to zero and removes net_device from kernel. There is not any
running routines after executing unregister_netdev(). Therefore, we could
not arouse timer from userspace again.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2022-02-17

We've added 8 non-merge commits during the last 7 day(s) which contain
a total of 8 files changed, 119 insertions(+), 15 deletions(-).

The main changes are:

1) Add schedule points in map batch ops, from Eric.

2) Fix bpf_msg_push_data with len 0, from Felix.

3) Fix crash due to incorrect copy_map_value, from Kumar.

4) Fix crash due to out of bounds access into reg2btf_ids, from Kumar.

5) Fix a bpf_timer initialization issue with clang, from Yonghong.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf: Add schedule points in batch ops
  bpf: Fix crash due to out of bounds access into reg2btf_ids.
  selftests: bpf: Check bpf_msg_push_data return value
  bpf: Fix a bpf_timer initialization issue
  bpf: Emit bpf_timer in vmlinux BTF
  selftests/bpf: Add test for bpf_timer overwriting crash
  bpf: Fix crash due to incorrect copy_map_value
  bpf: Do not try bpf_msg_push_data with len 0
====================

Link: https://lore.kernel.org/r/20220217190000.37925-1-alexei.starovoitov@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from wireless and netfilter.

  Current release - regressions:

   - dsa: lantiq_gswip: fix use after free in gswip_remove()

   - smc: avoid overwriting the copies of clcsock callback functions

  Current release - new code bugs:

   - iwlwifi:
      - fix use-after-free when no FW is present
      - mei: fix the pskb_may_pull check in ipv4
      - mei: retry mapping the shared area
      - mvm: don't feed the hardware RFKILL into iwlmei

  Previous releases - regressions:

   - ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()

   - tipc: fix wrong publisher node address in link publications

   - iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
     assertion

   - bgmac: make idm and nicpm resource optional again

   - atl1c: fix tx timeout after link flap

  Previous releases - always broken:

   - vsock: remove vsock from connected table when connect is
     interrupted by a signal

   - ping: change destination interface checks to match raw sockets

   - crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
     semantics (and null-deref) after SO_RESERVE_MEM was added

   - ipv6: make exclusive flowlabel checks per-netns

   - bonding: force carrier update when releasing slave

   - sched: limit TC_ACT_REPEAT loops

   - bridge: multicast: notify switchdev driver whenever MC processing
     gets disabled because of max entries reached

   - wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found

   - iwlwifi: fix locking when "HW not ready"

   - phy: mediatek: remove PHY mode check on MT7531

   - dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN

   - dsa: lan9303:
      - fix polarity of reset during probe
      - fix accelerated VLAN handling"

* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
  bonding: force carrier update when releasing slave
  nfp: flower: netdev offload check for ip6gretap
  ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
  ipv4: fix data races in fib_alias_hw_flags_set
  net: dsa: lan9303: add VLAN IDs to master device
  net: dsa: lan9303: handle hwaccel VLAN tags
  vsock: remove vsock from connected table when connect is interrupted by a signal
  Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
  ping: fix the dif and sdif check in ping_lookup
  net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
  net: sched: limit TC_ACT_REPEAT loops
  tipc: fix wrong notification node addresses
  net: dsa: lantiq_gswip: fix use after free in gswip_remove()
  ipv6: per-netns exclusive flowlabel checks
  net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
  CDC-NCM: avoid overflow in sanity checking
  mctp: fix use after free
  net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
  bonding: fix data-races around agg_select_timer
  dpaa2-eth: Initialize mutex used in one step timestamping path
  ...

In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.

Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.

Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0

Fixes: ff59c456 ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot reported various soft lockups caused by bpf batch operations.

 INFO: task kworker/1:1:27 blocked for more than 140 seconds.
 INFO: task hung in rcu_barrier

Nothing prevents batch ops to process huge amount of data,
we need to add schedule points in them.

Note that maybe_wait_bpf_programs(map) calls from
generic_map_delete_batch() can be factorized by moving
the call after the loop.

This will be done later in -next tree once we get this fix merged,
unless there is strong opinion doing this optimization sooner.

Fixes: aa2e93b8 ("bpf: Add generic support for update and delete batch ops")
Fixes: cb4d03ab ("bpf: Add generic support for lookup batch op")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/bpf/20220217181902.808742-1-eric.dumazet@gmail.com

Commit b42bc9a3 ("Fix regression due to "fs: move binfmt_misc sysctl
to its own file") fixed a regression, however it failed to add a
kmemleak_not_leak().

Fixes: b42bc9a3 ("Fix regression due to "fs: move binfmt_misc sysctl to its own file")
Reported-by: Tong Zhang <ztong0001@gmail.com>
Cc: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'perf-tools-fixes-for-v5.17-2022-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix corrupt inject files when only last branch option is enabled with
   ARM CoreSight ETM

 - Fix use-after-free for realloc(..., 0) in libsubcmd, found by gcc 12

 - Defer freeing string after possible strlen() on it in the BPF loader,
   found by gcc 12

 - Avoid early exit in 'perf trace' due SIGCHLD from non-workload
   processes

 - Fix arm64 perf_event_attr 'perf test's wrt --call-graph
   initialization

 - Fix libperf 32-bit build for 'perf test' wrt uint64_t printf

 - Fix perf_cpu_map__for_each_cpu macro in libperf, providing access to
   the CPU iterator

 - Sync linux/perf_event.h UAPI with the kernel sources

 - Update Jiri Olsa's email address in MAINTAINERS

* tag 'perf-tools-fixes-for-v5.17-2022-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf bpf: Defer freeing string after possible strlen() on it
  perf test: Fix arm64 perf_event_attr tests wrt --call-graph initialization
  libsubcmd: Fix use-after-free for realloc(..., 0)
  libperf: Fix perf_cpu_map__for_each_cpu macro
  perf cs-etm: Fix corrupt inject files when only last branch option is enabled
  perf cs-etm: No-op refactor of synth opt usage
  libperf: Fix 32-bit build for tests uint64_t printf
  tools headers UAPI: Sync linux/perf_event.h with the kernel sources
  perf trace: Avoid early exit due SIGCHLD from non-workload processes
  MAINTAINERS: Update Jiri's email address

Pull module fix from Luis Chamberlain:
 "Fixes module decompression when CONFIG_SYSFS=n

  The only fix trickled down for v5.17-rc cycle so far is the fix for
  module decompression when CONFIG_SYSFS=n. This was reported through
  0-day"

* tag 'modules-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
  module: fix building with sysfs disabled

IPv6 GRE tunnels are not being offloaded, this is caused by a missing
netdev offload check. The functionality of IPv6 GRE tunnel offloading
was previously added but this check was not included. Adding the
ip6gretap check allows IPv6 GRE tunnels to be offloaded correctly.

Fixes: f7536ffb ("nfp: flower: Allow ipv6gretap interface for offloading")
Signed-off-by: Danie du Toit <danie.dutoit@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220217124820.40436-1-louis.peens@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Because fib6_info_hw_flags_set() is called without any synchronization,
all accesses to gi6->offload, fi->trap and fi->offload_failed
need some basic protection like READ_ONCE()/WRITE_ONCE().

BUG: KCSAN: data-race in fib6_info_hw_flags_set / fib6_purge_rt

read to 0xffff8881087d5886 of 1 bytes by task 13953 on cpu 0:
 fib6_drop_pcpu_from net/ipv6/ip6_fib.c:1007 [inline]
 fib6_purge_rt+0x4f/0x580 net/ipv6/ip6_fib.c:1033
 fib6_del_route net/ipv6/ip6_fib.c:1983 [inline]
 fib6_del+0x696/0x890 net/ipv6/ip6_fib.c:2028
 __ip6_del_rt net/ipv6/route.c:3876 [inline]
 ip6_del_rt+0x83/0x140 net/ipv6/route.c:3891
 __ipv6_dev_ac_dec+0x2b5/0x370 net/ipv6/anycast.c:374
 ipv6_dev_ac_dec net/ipv6/anycast.c:387 [inline]
 __ipv6_sock_ac_close+0x141/0x200 net/ipv6/anycast.c:207
 ipv6_sock_ac_close+0x79/0x90 net/ipv6/anycast.c:220
 inet6_release+0x32/0x50 net/ipv6/af_inet6.c:476
 __sock_release net/socket.c:650 [inline]
 sock_close+0x6c/0x150 net/socket.c:1318
 __fput+0x295/0x520 fs/file_table.c:280
 ____fput+0x11/0x20 fs/file_table.c:313
 task_work_run+0x8e/0x110 kernel/task_work.c:164
 tracehook_notify_resume include/linux/tracehook.h:189 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
 exit_to_user_mode_prepare+0x160/0x190 kernel/entry/common.c:207
 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
 syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:300
 do_syscall_64+0x50/0xd0 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x44/0xae

write to 0xffff8881087d5886 of 1 bytes by task 1912 on cpu 1:
 fib6_info_hw_flags_set+0x155/0x3b0 net/ipv6/route.c:6230
 nsim_fib6_rt_hw_flags_set drivers/net/netdevsim/fib.c:668 [inline]
 nsim_fib6_rt_add drivers/net/netdevsim/fib.c:691 [inline]
 nsim_fib6_rt_insert drivers/net/netdevsim/fib.c:756 [inline]
 nsim_fib6_event drivers/net/netdevsim/fib.c:853 [inline]
 nsim_fib_event drivers/net/netdevsim/fib.c:886 [inline]
 nsim_fib_event_work+0x284f/0x2cf0 drivers/net/netdevsim/fib.c:1477
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x2c7/0x2e0 kernel/kthread.c:327
 ret_from_fork+0x1f/0x30

value changed: 0x22 -> 0x2a

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1912 Comm: kworker/1:3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events nsim_fib_event_work

Fixes: 0c5fcf9e ("IPv6: Add "offload failed" indication to routes")
Fixes: bb3c4ab9 ("ipv6: Add "offload" and "trap" indications to routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amit Cohen <amcohen@nvidia.com>
Cc: Ido Schimmel <idosch@nvidia.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220216173217.3792411-2-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>