- 05 Feb, 2013 40 commits
-
-
Sachin Kamat authored
Fixes the following warning: drivers/media/platform/s5p-mfc/s5p_mfc_opr.c:56:27: warning: Using plain integer as NULL pointer Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M format is half of the Y plane value, rather than having same bytesperline for all planes. While at it, simplify the bytesperline parameter handling by storing it when image format is set and returning those values when getting the format, instead of recalculating bytesperline from intermediate parameters. Reported-by: Sebastian Dröge <sebastian.droege@collabora.co.uk> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Kamil Debski authored
Fixed wrong condition in firmware reload function used by the watchdog. Signed-off-by: Kamil Debski <k.debski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
Fixes a v4l2-compliance error: setting audmode to a value other than mono or stereo for a radio device should map to MODE_STEREO. The spec specifies that for radio devices only mono and stereo audmodes are valid. If the user specifies another audmode in v4l2_tuner, then that should be mapped to valid audmode. That didn't happen here. Note that tuner drivers might decide to limit the possible audmode even further if it only supports mono. In that case the tuner driver can set audmode to mono. However, that new value wasn't copied back to t->audmode, and that has been fixed as well in this patch. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors. The driver exposes following V4L2 controls: - auto/manual exposure, - auto/manual white balance, - auto/manual gain, - brightness, saturation, sharpness, - horizontal/vertical flip, - color bar test pattern, - banding filter (power line frequency). Frame rate can be configured with g/s_frame_interval pad level ops. Supported resolution are only: SXGA, VGA, QVGA. Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
This patch adds a v4l2 core helper function that can be used as the log_status handler for subdevs that only need to log state of the v4l2 controls owned by the subdev's control handler. Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
Add a v4l2 core helper function that can be used as the subdev .subscribe_event handler. This allows to eliminate some boilerplate from drivers that are only handling the control events. Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
Add a v4l2 core helper function that can be used as the subdev .unsubscribe_event handler. This allows to eliminate some boilerplate from drivers that are only handling the control events. Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
This patch adds a helper function that allows to modify range, i.e. minimum, maximum, step and default value of a v4l2 control, after the control has been created and initialized. This is helpful in situations when range of a control depends on user configurable parameters, e.g. camera sensor absolute exposure time depending on an output image resolution and frame rate. v4l2_ctrl_modify_range() function allows to modify range of an INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls. Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654. Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sylwester Nawrocki authored
Add common header file defining standard image sizes, so we can avoid redefining those in each driver. Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans de Goede authored
Instead chaneg the passed in format to the pwc default pixelformat. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Also replaced: #if !defined CONFIG_USB_SN9C102 && !defined CONFIG_USB_SN9C102_MODULE with: #if !IS_ENABLED(CONFIG_USB_SN9C102) Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_INPUT) || \ defined(CONFIG_INPUT_MODULE) with: #if IS_ENABLED(CONFIG_INPUT) This change was made for: CONFIG_INPUT Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Peter Senna Tschudin authored
replace: #if defined(CONFIG_USB_SI470X) || \ defined(CONFIG_USB_SI470X_MODULE) with: #if IS_ENABLED(CONFIG_USB_SI470X) This change was made for: CONFIG_USB_SI470X, CONFIG_I2C_SI470X Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Johannes Schellen authored
This patch fixes a bug which causes all histogram regions to start in the top left corner of the image. The histogram region coordinates are 16 bit values which share a 32 bit register. The bug is due to the region end value assignments overwriting the region start values with zero. Signed-off-by: Johannes Schellen <Johannes.Schellen@rwth-aachen.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
Replace kzalloc, request_mem_region, ioremap, clk_get and regulator_get with their devm_* managed replacement. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
kzalloc initializes the memory it allocates to 0, there's no need for an explicit memset. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
The preview engine includes filters that consume columns and lines as part of their operation, thus resulting in a cropped image. To allow turning those filters on/off during streaming without affecting the output image size, the driver adds additional cropping to make the total number of cropped columns and lines constant regardless of which filters are enabled. This process needlessly includes the CFA filter, as whether the filter is enabled only depends on the sink pad format, which can't change during streaming. Exclude the CFA filter from the preview engine margins. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Oliver Neukum authored
Ming Lei reported: IMO, there is a minor fault in the error handling path of uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should have been decreased before usb_autopm_put_interface(). In theory, a [URB resubmission] warning can be triggered when the device is opened just between usb_autopm_put_interface() and atomic_dec(&stream->dev->users). The fix is trivial. Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ezequiel Garcia authored
This kind of memcpy() is error-prone. Its replacement with a struct assignment is prefered because it's type-safe and much easier to read. Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Wei Yongjun authored
Add the missing unlock on the error handling path in function vpbe_initialize(). Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Prabhakar Lad <prabhakar.lad@ti.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be used uninitialized in this function [-Wuninitialized] drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here This is a false positive but the compiler has no way to know about it, so initialize the variable to 0. Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so simplifies their clean up paths. Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-