commit 8defb336 upstream.

Usually ELF_ET_DYN_BASE is 2/3 of TASK_SIZE. With 3G/1G user/kernel
split this is not so, because 2*TASK_SIZE overflows 32 bits,
so the actual value of ELF_ET_DYN_BASE is:
	(2 * TASK_SIZE / 3) = 0x2a000000

When ASLR is disabled PIE binaries will load at ELF_ET_DYN_BASE address.
On 32bit platforms AddressSanitzer uses addresses [0x20000000 - 0x40000000]
for shadow memory [1]. So ASan doesn't work for PIE binaries when ASLR disabled
as it fails to map shadow memory.
Also after Kees's 'split ET_DYN ASLR from mmap ASLR' patchset PIE binaries
has a high chance of loading somewhere in between [0x2a000000 - 0x40000000]
even if ASLR enabled. This makes ASan with PIE absolutely incompatible.

Fix overflow by dividing TASK_SIZE prior to multiplying.
After this patch ELF_ET_DYN_BASE equals to (for CONFIG_VMSPLIT_3G=y):
	(TASK_SIZE / 3 * 2) = 0x7f555554

[1] https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerAlgorithm#MappingSigned-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reported-by: Maria Guseva <m.guseva@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3c3b04d1 upstream.

Due to insufficient check in btrfs_is_valid_xattr, this unexpectedly
works:

 $ touch file
 $ setfattr -n user. -v 1 file
 $ getfattr -d file
user.="1"

ie. the missing attribute name after the namespace.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94291Reported-by: William Douglas <william.douglas@intel.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
[bwh: Backported to 3.2: XATTR_BTRFS_PREFIX is not supported]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit dcc82f47 upstream.

While committing a transaction we free the log roots before we write the
new super block. Freeing the log roots implies marking the disk location
of every node/leaf (metadata extent) as pinned before the new super block
is written. This is to prevent the disk location of log metadata extents
from being reused before the new super block is written, otherwise we
would have a corrupted log tree if before the new super block is written
a crash/reboot happens and the location of any log tree metadata extent
ended up being reused and rewritten.

Even though we pinned the log tree's metadata extents, we were issuing a
discard against them if the fs was mounted with the -o discard option,
resulting in corruption of the log tree if a crash/reboot happened before
writing the new super block - the next time the fs was mounted, during
the log replay process we would find nodes/leafs of the log btree with
a content full of zeroes, causing the process to fail and require the
use of the tool btrfs-zero-log to wipeout the log tree (and all data
previously fsynced becoming lost forever).

Fix this by not doing a discard when pinning an extent. The discard will
be done later when it's safe (after the new super block is committed) at
extent-tree.c:btrfs_finish_extent_commit().

Fixes: e688b725 (Btrfs: fix extent pinning bugs in the tree log)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 73cffdb6 upstream.

Don't wait after sending request for offers to the host. This wait is
unnecessary and simply adds 5 seconds to the boot time.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: deleted variable t was declared as int]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 299d0c5b upstream.

The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.

Coverity CID #139400
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f16db807 upstream.

In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.

This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.

Coverity CID #113449
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d74adbdb upstream.

If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the
PEB->LEB mapping.

Caught by Coverity, CID #711212.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.2: adjust context; s/leb/seb/g]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8eef7d70 upstream.

We are completely discarding the earlier value of 'bitflips', which
could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the
bitwise OR of header and data 'bitflip' statuses instead.

Coverity CID #1226856
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2c20d92d upstream.

the lcd type as defined in the Kconfig is not matching in the code.
as a result the rs, rw and en pins were getting interchanged.
Kconfig defines the value of PANEL_LCD to be 1 if we select custom
configuration but in the code LCD_TYPE_CUSTOM is defined as 5.

my hardware is LCD_TYPE_CUSTOM, but the pins were assigned to it
as pins of LCD_TYPE_OLD, and it was not working.
Now values are corrected with referenece to the values defined in
Kconfig and it is working.
checked on JHD204A lcd with LCD_TYPE_CUSTOM configuration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: parameter description was split across two lines]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 323ece54 upstream.

Values directly from descriptors given in debug statements
must be converted to native endianness.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8787041d upstream.

The WM8741 DAC supports the following typical audio sampling rates:
  44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz)
  32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz)

For the rates lists, we should use 82000 instead of 88235, 176400
instead of 1764000 and 192000 instead of 19200 (seems to be a typo).
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0b053c95 upstream.

OPTIMIZER_HIDE_VAR(), as defined when using gcc, is insufficient to
ensure protection from dead store optimization.

For the random driver and crypto drivers, calls are emitted ...

  $ gdb vmlinux
  (gdb) disassemble memzero_explicit
  Dump of assembler code for function memzero_explicit:
    0xffffffff813a18b0 <+0>:	push   %rbp
    0xffffffff813a18b1 <+1>:	mov    %rsi,%rdx
    0xffffffff813a18b4 <+4>:	xor    %esi,%esi
    0xffffffff813a18b6 <+6>:	mov    %rsp,%rbp
    0xffffffff813a18b9 <+9>:	callq  0xffffffff813a7120 <memset>
    0xffffffff813a18be <+14>:	pop    %rbp
    0xffffffff813a18bf <+15>:	retq
  End of assembler dump.

  (gdb) disassemble extract_entropy
  [...]
    0xffffffff814a5009 <+313>:	mov    %r12,%rdi
    0xffffffff814a500c <+316>:	mov    $0xa,%esi
    0xffffffff814a5011 <+321>:	callq  0xffffffff813a18b0 <memzero_explicit>
    0xffffffff814a5016 <+326>:	mov    -0x48(%rbp),%rax
  [...]

... but in case in future we might use facilities such as LTO, then
OPTIMIZER_HIDE_VAR() is not sufficient to protect gcc from a possible
eviction of the memset(). We have to use a compiler barrier instead.

Minimal test example when we assume memzero_explicit() would *not* be
a call, but would have been *inlined* instead:

  static inline void memzero_explicit(void *s, size_t count)
  {
    memset(s, 0, count);
    <foo>
  }

  int main(void)
  {
    char buff[20];

    snprintf(buff, sizeof(buff) - 1, "test");
    printf("%s", buff);

    memzero_explicit(buff, sizeof(buff));
    return 0;
  }

With <foo> := OPTIMIZER_HIDE_VAR():

  (gdb) disassemble main
  Dump of assembler code for function main:
  [...]
   0x0000000000400464 <+36>:	callq  0x400410 <printf@plt>
   0x0000000000400469 <+41>:	xor    %eax,%eax
   0x000000000040046b <+43>:	add    $0x28,%rsp
   0x000000000040046f <+47>:	retq
  End of assembler dump.

With <foo> := barrier():

  (gdb) disassemble main
  Dump of assembler code for function main:
  [...]
   0x0000000000400464 <+36>:	callq  0x400410 <printf@plt>
   0x0000000000400469 <+41>:	movq   $0x0,(%rsp)
   0x0000000000400471 <+49>:	movq   $0x0,0x8(%rsp)
   0x000000000040047a <+58>:	movl   $0x0,0x10(%rsp)
   0x0000000000400482 <+66>:	xor    %eax,%eax
   0x0000000000400484 <+68>:	add    $0x28,%rsp
   0x0000000000400488 <+72>:	retq
  End of assembler dump.

As can be seen, movq, movq, movl are being emitted inlined
via memset().

Reference: http://thread.gmane.org/gmane.linux.kernel.cryptoapi/13764/
Fixes: d4c5efdb ("random: add and use memzero_explicit() for clearing data")
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: mancha security <mancha1@zoho.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit fd99a094 upstream.

Use the correct flags for atom.

v2: handle DRM_MODE_FLAG_DBLCLK
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 838d030b upstream.

The callback function signature has changed in commit a5818a8b (pinctrl:
get_group_pins() const fixes)

Fixes: a5818a8b ('pinctrl: get_group_pins() const fixes')
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1915a718 upstream.

The return value of power_supply_register() call was not checked and
even on error probe() function returned 0. If registering failed then
during unbind the driver tried to unregister power supply which was not
actually registered.

This could lead to memory corruption because power_supply_unregister()
unconditionally cleans up given power supply.

Fix this by checking return status of power_supply_register() call. In
case of failure, clean up sysfs entries and fail the probe.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 9be0fcb5 ("compal-laptop: add JHL90, battery & hwmon interface")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
[bwh: Backported to 3.2: insert the appropriate cleanup code as there is no
 common 'remove' label]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit e3c93e1a upstream.

As per Mentor Graphics' documentation, we should
always handle TX endpoints before RX endpoints.

This patch fixes that error while also updating
some hard-to-read comments which were scattered
around musb_interrupt().

This patch should be backported as far back as
possible since this error has been in the driver
since it's conception.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[bwh: Backported to 3.2: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b75f4c9a upstream.

s390 documentation requires words 0 and 10-15 to be reserved and stored as
zeros. As we fill out all other fields, we can memset the full structure.
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 08e83316 upstream.

There is a race condition between e1000_change_mtu's cleanups and
netpoll, when we change the MTU across jumbo size:

Changing MTU frees all the rx buffers:
    e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings ->
        e1000_clean_rx_ring

Then, close to the end of e1000_change_mtu:
    pr_info -> ... -> netpoll_poll_dev -> e1000_clean ->
        e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag

And when we come back to do the rest of the MTU change:
    e1000_up -> e1000_configure -> e1000_configure_rx ->
        e1000_alloc_jumbo_rx_buffers

alloc_jumbo finds the buffers already != NULL, since data (shared with
page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage,
or at least not what is expected when in jumbo state.

This results in an unusable adapter (packets don't get through), and a
NULL pointer dereference on the next call to e1000_clean_rx_ring
(other mtu change, link down, shutdown):

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330

    [...]

Call Trace:
 [<ffffffff81195445>] put_page+0x55/0x60
 [<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200
 [<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60
 [<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0
 [<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840
 [<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170
 [<ffffffff81647050>] dev_set_mtu+0xa0/0x140
 [<ffffffff81664218>] do_setlink+0x218/0xac0
 [<ffffffff814459e9>] ? nla_parse+0xb9/0x120
 [<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890
 [<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40
 [<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100
 [<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260

By setting the allocator to a dummy version, netpoll can't mess up our
rx buffers.  The allocator is set back to a sane value in
e1000_configure_rx.

Fixes: edbbb3ca ("e1000: implement jumbo receive with partial descriptors")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 40384e4b upstream.

Correctly rollback state if the failure occurs after we have handed over
the ownership of the buffer to the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2eeff0b4 upstream.

Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so
that the device can load the ath3k firmware and re-enumerate itself as an
AR3011 device.

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04f2 ProdID=aff1 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Alexander Ploumistos <alexpl@fedoraproject.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

This reverts commit 823f1402, which was
commit 2dca485f upstream.  It
depends on functionality that is not present in 3.2.y.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>

commit 3b05ac38 upstream.

The app_tcp_pkt_out() function expects "*diff" to be set and ends up
using uninitialized data if CONFIG_IP_VS_IPV6 is turned on.

The same issue is there in app_tcp_pkt_in().  Thanks to Julian Anastasov
for noticing that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>

commit 579eb62a upstream.

commit f5a41847 ("ipvs: move ip_route_me_harder for ICMP")
from 2.6.37 introduced ip_route_me_harder() call for responses to
local clients, so that we can provide valid rt_src after SNAT.
It was used by TCP to provide valid daddr for ip_send_reply().
After commit 0a5ebb80 ("ipv4: Pass explicit daddr arg to
ip_send_reply()." from 3.0 this rerouting is not needed anymore
and should be avoided, especially in LOCAL_IN.

Fixes 3.12.33 crash in xfrm reported by Florian Wiessner:
"3.12.33 - BUG xfrm_selector_match+0x25/0x2f6"
Reported-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Tested-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>

commit 377b5134 upstream.

Clear the reserved field of struct ib_uverbs_async_event_desc which is
copied to user space.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Yann Droneaud <ydroneaud@opteya.com>

commit f20fbaad upstream.

`spidev_message()` sums the lengths of the individual SPI transfers to
determine the overall SPI message length.  It restricts the total
length, returning an error if too long, but it does not check for
arithmetic overflow.  For example, if the SPI message consisted of two
transfers and the first has a length of 10 and the second has a length
of (__u32)(-1), the total length would be seen as 9, even though the
second transfer is actually very long.  If the second transfer specifies
a null `rx_buf` and a non-null `tx_buf`, the `copy_from_user()` could
overrun the spidev's pre-allocated tx buffer before it reaches an
invalid user memory address.  Fix it by checking that neither the total
nor the individual transfer lengths exceed the maximum allowed value.

Thanks to Dan Carpenter for reporting the potential integer overflow.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
[Ian Abbott: Note: original commit compares the lengths to INT_MAX
 instead of bufsiz due to changes in earlier commits.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 330966e5 upstream.

skb_gso_segment has three possible return values:
1. a pointer to the first segmented skb
2. an errno value (IS_ERR())
3. NULL.  This can happen when GSO is used for header verification.

However, several callers currently test IS_ERR instead of IS_ERR_OR_NULL
and would oops when NULL is returned.

Note that these call sites should never actually see such a NULL return
value; all callers mask out the GSO bits in the feature argument.

However, there have been issues with some protocol handlers erronously not
respecting the specified feature mask in some cases.

It is preferable to get 'have to turn off hw offloading, else slow' reports
rather than 'kernel crashes'.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Brad Spengler: backported to 3.2]
Signed-off-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 845704a5 ]

Presence of an unbound loop in tcp_send_fin() had always been hard
to explain when analyzing crash dumps involving gigantic dying processes
with millions of sockets.

Lets try a different strategy :

In case of memory pressure, try to add the FIN flag to last packet
in write queue, even if packet was already sent. TCP stack will
be able to deliver this FIN after a timeout event. Note that this
FIN being delivered by a retransmit, it also carries a Push flag
given our current implementation.

By checking sk_under_memory_pressure(), we anticipate that cooking
many FIN packets might deplete tcp memory.

In the case we could not allocate a packet, even with __GFP_WAIT
allocation, then not sending a FIN seems quite reasonable if it allows
to get rid of this socket, free memory, and not block the process from
eventually doing other useful work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
 - Drop inapplicable change to sk_forced_wmem_schedule()
 - s/sk_under_memory_pressure(sk)/tcp_memory_pressure/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 2ab95749 ]

Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets

Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.

This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.

v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c9974ad4 upstream.

netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts.  For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: use only dev_kfree_skb() and not dev_consume_skb_any()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d8ec2c02 upstream.

Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f7e79913 upstream.

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 497a27b9 upstream.

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 989c9ba1 upstream.

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a2ccd2e4 upstream.

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 508f81d5 upstream.

Replace kfree_skb with dev_kfree_skb_any in cp_start_xmit
as it can be called in both hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 355a901e ]

While working on sk_forward_alloc problems reported by Denys
Fedoryshchenko, we found that tcp connect() (and fastopen) do not call
sk_wmem_schedule() for SYN packet (and/or SYN/DATA packet), so
sk_forward_alloc is negative while connect is in progress.

We can fix this by calling regular sk_stream_alloc_skb() both for the
SYN packet (in tcp_connect()) and the syn_data packet in
tcp_send_syn_data()

Then, tcp_send_syn_data() can avoid copying syn_data as we simply
can manipulate syn_data->cb[] to remove SYN flag (and increment seq)

Instead of open coding memcpy_fromiovecend(), simply use this helper.

This leaves in socket write queue clean fast clone skbs.

This was tested against our fastopen packetdrill tests.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
 - Drop the Fast Open changes
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 7d985ed1 ]

[I would really like an ACK on that one from dhowells; it appears to be
quite straightforward, but...]

MSG_PEEK isn't passed to ->recvmsg() via msg->msg_flags; as the matter of
fact, neither the kernel users of rxrpc, nor the syscalls ever set that bit
in there.  It gets passed via flags; in fact, another such check in the same
function is done correctly - as flags & MSG_PEEK.

It had been that way (effectively disabled) for 8 years, though, so the patch
needs beating up - that case had never been tested.  If it is correct, it's
-stable fodder.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit 3eeff778 ]

It should be checking flags, not msg->msg_flags.  It's ->sendmsg()
instances that need to look for that in ->msg_flags, ->recvmsg() ones
(including the other ->recvmsg() instance in that file, as well as
unix_dgram_recvmsg() this one claims to be imitating) check in flags.
Braino had been introduced in commit dcda13 ("caif: Bugfix - use MSG_TRUNC
in receive") back in 2010, so it goes quite a while back.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

[ Upstream commit f862e07c ]

The rds_iw_update_cm_id function stores a large 'struct rds_sock' object
on the stack in order to pass a pair of addresses. This happens to just
fit withint the 1024 byte stack size warning limit on x86, but just
exceed that limit on ARM, which gives us this warning:

net/rds/iw_rdma.c:200:1: warning: the frame size of 1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]

As the use of this large variable is basically bogus, we can rearrange
the code to not do that. Instead of passing an rds socket into
rds_iw_get_device, we now just pass the two addresses that we have
available in rds_iw_update_cm_id, and we change rds_iw_get_mr accordingly,
to create two address structures on the stack there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>