Better to have a clear name for the function. While at it, clear up the title
for the register dump.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.

kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k_pci_diag_read32() is for reading u32 from a device and ath10k_pci_diag_read_hi()
is a helper for reading data using "host interest" table.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Service mapping for main firmware branch was incorrectly used for 10.x firmware
and vice-versa.  This caused wmi_services in debugfs to print wrong values.

This fixes commit cff990ce ("ath10k: fix wmi service bitmap debug") where
for some reason there was either a conflict that wasn't resolved properly or
git had a bad day.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If spectral is unregistered after mac80211, the relayfs file has already
been removed recursively by mac/cfg80211, and spectral tries to remove
the file once more, thus leading to double free problems. Better clean
up spectral before to avoid that problem.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch adds device ID 402 to support QCA6234X found in APQ8064 SOC
in IFC6410 board.

Tested with mainline mmci sdio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

tranmist -> transmit
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Check vdev map has space before calling ffs,
fix invalid cleanup in failure to create vdev
case.

Open-code the BIT() logic since BIT does not properly
handle 64-bit bitfields and future patches will make
use of larger bitfields.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is not necessary anymore. There are no more
uncontrolled htc tx entry points.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Make probe/remove functions shorter and easier to
understand.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The ATH10K_PCI_FEATURE_MSI_X was originally
introduced to support both chips QCA988Xv1 and
QCA988Xv2. Since v1 isn't supported anymore it
doesn't make sense to keep the feature flag
around. Since this is the last one remove the
whole thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The soc powersave was disabled by default. It
never was fully tested. Some hw apparently had
problems with it and the implementation itself had
a possible race.

Just remove the refcounting and simply wake up the
device when probing and put to sleep when
removing.

kvalo: make ath10k_pci_wake() and _sleep() static
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Use the common convention of embedding private
structures inside parent structures. This
reduces allocations and simplifies pci probing
code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.

One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This also reduces the cruft of printing scan event
names in capitals.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.

This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.

kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This converts a driver in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a
bit simpler.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.

Essentially, to try it out:

ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples

This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The ath9k and ath10k will share the definitions of the debugfs spectral
structures and enums. Having them in the same place helps to avoid conflicts.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.

Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.

This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Print sequence number, AMSDU_MORE flag and AC when additional
debug enabled in RX path. This is usefull for debugging purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:

 br0: received packet on wlan0.sta1 with own address as source address

Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: Vu Hai NGUYEN <vh.nguyen@actiasodielec.fr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.

The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Different firmware may support different numbers of
vdevs.  Use value that is always out of range for all
firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In case of A-MSDU RX we should check attention flags
correctly to be sure we report correct FCS status for
A-MSDU subframes. Without a patch we could report A-MSDU
subframes with wrong FCS as a correct to the stack, next
get a lot of DUP ACK TCP packets. Finally TP drop is seen
and this drop depends on FCS errors ratio for A-MSDU frame.

Example test case when TP drop is seen:
- ath10k configured as an AP
- used ath10k station
- forced A-MSDU (7 frames) on STA
- other traffic on channel (often FCS errors)
- monitor iface added on AP
- TCP STA -> AP traffic (iperf)

a) Iperf logs for case without the patch:

echo "1 64" > htt_max_amsdu_ampdu // disable A-MSDU
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 5.0 sec  56.6 MBytes  95.0 Mbits/sec
[  3]  5.0-10.0 sec  60.4 MBytes   101 Mbits/sec
[  3] 10.0-15.0 sec  60.2 MBytes   101 Mbits/sec
[  3] 15.0-20.0 sec  60.2 MBytes   101 Mbits/sec
[  3] 20.0-25.0 sec  63.8 MBytes   107 Mbits/sec
[  3] 25.0-30.0 sec  64.9 MBytes   109 Mbits/sec

echo "7 64" > htt_max_amsdu_ampdu  // set 7 A-MSDU subframes
[  3] 30.0-35.0 sec  40.0 MBytes  67.1 Mbits/sec
[  3] 35.0-40.0 sec  35.9 MBytes  60.2 Mbits/sec
[  3] 40.0-45.0 sec  36.9 MBytes  61.9 Mbits/sec
[  3] 45.0-50.0 sec  37.9 MBytes  63.5 Mbits/sec
[  3] 50.0-55.0 sec  34.5 MBytes  57.9 Mbits/sec
[  3] 55.0-60.0 sec  25.4 MBytes  42.6 Mbits/sec
[  3] 60.0-65.0 sec  48.2 MBytes  81.0 Mbits/sec
[  3] 65.0-70.0 sec  28.8 MBytes  48.2 Mbits/sec
[  3] 70.0-75.0 sec  29.2 MBytes  49.1 Mbits/sec
[  3] 75.0-80.0 sec  22.9 MBytes  38.4 Mbits/sec
[  3] 80.0-85.0 sec  26.4 MBytes  44.2 Mbits/sec
[  3] 85.0-90.0 sec  31.5 MBytes  52.8 Mbits/sec

b) Iperf logs for case with patch:

echo "1 64" > htt_max_amsdu_ampdu // disable A-MSDU
[  3] local 192.168.12.2 port 57512 connected with 192.168.12.1 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0- 5.0 sec  60.8 MBytes   102 Mbits/sec
[  3]  5.0-10.0 sec  62.2 MBytes   104 Mbits/sec
[  3] 10.0-15.0 sec  60.9 MBytes   102 Mbits/sec

echo "7 64" > htt_max_amsdu_ampdu  // set 7 A-MSDU subframes
[  3] 15.0-20.0 sec  68.1 MBytes   114 Mbits/sec
[  3] 20.0-25.0 sec  80.5 MBytes   135 Mbits/sec
[  3] 25.0-30.0 sec  83.0 MBytes   139 Mbits/sec
[  3] 30.0-35.0 sec  79.1 MBytes   133 Mbits/sec
[  3] 35.0-40.0 sec  77.1 MBytes   129 Mbits/sec
[  3] 40.0-45.0 sec  77.4 MBytes   130 Mbits/sec
Reported-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.

Use mac80211 to perform reordering instead of
re-inventing the wheel.

This fixes TCP throughput issues in some
environments.
Reported-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This has been tested on 14e4:4328 (BCM4321), 14e4:432b (BCM4322),
14e4:4353 (BCM43224) and 14e4:4359 (BCM43228) which is an almost
complete list of 5 GHz capable device (only BCM43222 is missing).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We don't have all needed channel tables due to RE process for this
device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This process requires sending some sample tone, so make sure we're
allowed to transmit first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

So far we were assuming only A-PHY supports 5 GHz.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The dividend in do_div() is expected to be an unsigned 64-bit integer,
which leads to the following warning when building for 32-bit MIPS:

  drivers/net/wireless/mac80211_hwsim.c: In function 'mac80211_hwsim_set_tsf':
  drivers/net/wireless/mac80211_hwsim.c:664:98: warning: comparison of distinct pointer types lacks a cast [enabled by default]
    data->bcn_delta = do_div(delta, bcn_int);

Since we care about the signedness of delta when adjusting tsf_offset
and bcm_delta, use the absolute value for the division and compare
the two timestamps to determine the sign.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The DCM condition was not checked well for channel switch in both AP and
station scenarios. Teardown was also not done for AP/GO DCM. Add the
missing checks.
Reported-by: Peer, Ilan <ilan.peer@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

It was possible to enter an endless loop while
processing a single pci copy engine pipe. This
could effectively render ath10k incapable of
responding to any requests.

An example case when this could happen is when
firmware generates a lot of events, e.g. spectral
scan phyerr via WMI.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Some radios may share the same ID and revision but differ by a version.
E.g. radio in BCM5357B0 is version 1 and requires specific handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>