- 07 May, 2011 13 commits
-
-
Anji jonnala authored
HSUSB core clock is derived from daytona fabric clock and for HSUSB operational require minimum core clock at 55MHz. Since, HSUSB cannot tolerate daytona fabric clock change in the middle of HSUSB operational, vote for maximum Daytona fabric clock while usb is operational Signed-off-by:
Anji jonnala <anjir@codeaurora.org> Signed-off-by:
Pavankumar Kondeti <pkondeti@codeaurora.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Jan Andersson authored
This patch adds support for the UHCI part of the GRLIB GRUSBHC controller found on some LEON/GRLIB SoCs. The UHCI HCD previously only supported controllers connected over PCI. This patch adds support for the first non-PCI UHCI HC. I have tried to replicate the solution used in ehci-hcd.c. Tested on GR-LEON4-ITX board (LEON4/GRLIB with GRUSBHC) and x86 with Intel UHCI HC. Signed-off-by:
Jan Andersson <jan@gaisler.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Jan Andersson authored
This patch is part of a series that extend the UHCI HCD to support non-PCI host controllers. This patch also extends the uhci_{read,write}* functions to allow accesses to registers not mapped into PCI I/O space. This extension also includes the addition of a void __iomem pointer to the uhci structure. A new Kconfig option is added to signal that the system has a non-PCI HC. If this Kconfig option is set, uhci-hcd.c will include generic reset functions for systems that do not make use of keyboard and mouse legacy support. PCI controllers will still always use the reset functions from pci-quirks This patch is followed by a patch that adds bus glue for the first non-PCI UHCI HC. Signed-off-by: -
Jan Andersson authored
This patch is part of a series that extend the UHCI HCD to support non-PCI controllers. This patch replaces in{b,w,l} and out{b,wl} with calls to local inline functions. This is done so that the register access functions can be extended to support register areas not mapped in PCI I/O space. Signed-off-by: -
Jan Andersson authored
This patch is part of a series that extend the UHCI HCD to support non-PCI controllers. This patch moves PCI specific functions to uhci-pci.c and includes this file in uhci-hcd.c. It also renames the function uhci_init to uhci_pci_init. uhci_init/uhci_pci_init is modified so that the port-detection logic is kept in a new separate function uhci_count_ports() in uhci-hcd.c. Signed-off-by:
-
Jan Andersson authored
This patch is part of a series that extend the UHCI HCD to support non-PCI host controllers. This patch fixes the following warnings from checkpatch: ERROR: switch and case should be at the same indent + switch (to_pci_dev(uhci_dev(uhci))->vendor) { + default: [...] + case PCI_VENDOR_ID_GENESYS: [...] + case PCI_VENDOR_ID_INTEL: WARNING: static char array declaration should probably be static const char + static char bad_Asus_board[] = "A7V8X"; WARNING: Use DEFINE_PCI_DEVICE_TABLE for struct pci_device_id +static const struct pci_device_id uhci_pci_ids[] = { { Signed-off-by: -
Jan Andersson authored
This patch is part of a series that extend the UHCI HCD to support non-PCI controllers. This patch changes calls to uhci_reset_hc, uhci_check_and_reset_hc, configure_hc, resume_detect_interrupts_are_broken and global_suspend_mode_is_broken so that they are made through pointers in the uhci hcd struct. This will allow these functions to be replaced with bus/arch specific functions. Signed-off-by:
-
Jan Andersson authored
This patch is part of a series that extend the UHCI HCD to support non-PCI host controllers. uhci-hub.c contained two PCI vendor checks for silicon quirks. Move these checks into uhci-hcd.c and use bits in uhci_hcd structure to mark that we need to use the quirks. This patch is followed by other patches that will remove PCI dependencies from uhci-hcd.c as well. Signed-off-by:
-
Ramneek Mehresh authored
Though USB controller works without this most of the time, an issue was faced where USB was configured as printer device and it was dropping first packet(64 bytes) in full speed mode due to DATA PID mismatch. The problem gets resolved once unused endpoints are configured as bulk. As per P1020 RM (Table17-31, bits 19-18, bits 3-2) "When only one endpoint (RX or TX, but not both) of an endpoint pair is used, the unused endpoint should be configured as a bulk type endpoint." So according to the RM, this patch is initializing TX and RX endpoints as bulk type Signed-off-by:
Suchit Lepcha <Suchit.Lepcha@freescale.com> Signed-off-by:
Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by:
-
Jingoo Han authored
Return PTR_ERR(clk) instead of -ENOENT if clk_get fails Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
Jingoo Han authored
This patch fixes the checkpatch errors ans warnings listed below: ERROR: do not use assignment in if condition WARNING: line over 80 characters WARNING: braces {} are not necessary for single statement blocks WARNING: space prohibited between function name and open parenthesis '(' Signed-off-by: -
Manuel Lauss authored
Remove a stray 'return 0' at the top of the suspend callback, and move au1xxx_stop_ehc() out of the ehci spinlock since it takes some time to complete. Signed-off-by:
Manuel Lauss <manuel.lauss@googlemail.com> Signed-off-by:
-
Anatolij Gustschin authored
Commit 3dacdf11 "usb: factor out state_string() on otg drivers" broke building musb drivers since there is already another otg_state_string() function in musb drivers, but with different prototype. Fix musb drivers to use common otg_state_string(), too. Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS is not defined. Signed-off-by:
Anatolij Gustschin <agust@denx.de> Signed-off-by:
-
- 03 May, 2011 27 commits
-
-
Jan Andersson authored
This patch adds support for the GRLIB GRUSBHC EHCI controller from Aeroflex Gaisler. The controller is typically found on LEON/GRLIB SoCs. Tested on GR-LEON4-ITX with with little endian interface and on LEON3 system on GR-PCI-XC5V development board for big endian controller. Signed-off-by:
-
Jan Andersson authored
The two first HC capability registers (CAPLENGTH and HCIVERSION) are defined as one 8-bit and one 16-bit register. Most HC implementations have selected to treat these registers as part of a 32-bit register, giving the same layout for both big and small endian systems. This patch adds a new quirk, big_endian_capbase, to support controllers with big endian register interfaces that treat HCIVERSION and CAPLENGTH as individual registers. Signed-off-by:
-
Pavankumar Kondeti authored
The current code is clearing in_lpm flag after enabling the IRQ. If IRQ comes immediately before in_lpm flag is set, it thinks that hardware is in low power mode and disables the IRQ. Fix this by clearing in_lpm flag before enabling the IRQ. Signed-off-by:
-
Anji jonnala authored
Some of the simulators may cache the ep0 maxpacket size to zero if the ep0 dQh is not setup before enabling the pullup. Hence Setup ep0 and initialize the dQh fields once while registering the gadget(before enabling the pullup). HSUSB Chipidea link controller spec says ep0 is enabled always in the HW. Hence disabling and enabling the ep0 as a part of reset interrupt is unneccesary. Remove the disable/enable ep0 logic from reset interrupt handling. Signed-off-by:
-
Pavankumar Kondeti authored
The current code queue the control OUT data request to ep0in instead of ep0out. Check ep0_dir and use the correct control endpoint. Signed-off-by:
-
Pavankumar Kondeti authored
The OUT endpoints are stored in 0 - hw_ep_max/2 and IN endpoints are stored from hw_ep_max/2 - hw_ep_max in ci13xxx_ep array. Retrieve the IN endpoint correctly while processing endpoint feature requests. Signed-off-by:
-
Pavankumar Kondeti authored
Signed-off-by:
-
Pavankumar Kondeti authored
Signed-off-by:
-
Pavankumar Kondeti authored
Signed-off-by:
-
Dmitry Eremin-Solenikov authored
Ask for vbus_draw regulator before registering tranceiver to disallow possible race between registration and set_power/etc. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by:
-
Michael Hund authored
Added several new devices to ldusb and excluded them from the HID driver. Signed-off-by:
Michael Hund <mhund@ld-didactic.de> Signed-off-by:
-
Rabin Vincent authored
As pointed out by Arnd Bergmann, in include/linux/usb/ehci_def.h, struct ehci_caps is defined with __attribute__((packed)) for no good reason, and this triggers undefined behaviour when using ARM's readl() on pointers to elements of this structure: http://lkml.kernel.org/r/201102021700.20683.arnd@arndb.de The same problem exists with the other two structures in ehci_def.h too, so remove the __attribute__((packed)) from all of them. Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
-
David Daney authored
The reset value of the uSOF cycle period is incorrect. Set it to 60,000 bits. Without this, several commercial USB flash memory devices and hubs fail to work properly. Signed-off-by:
David Daney <ddaney@caviumnetworks.com> Signed-off-by:
-
David Daney authored
Additional PHY tuning is needed to obtain compliant 'eye' diagram electrical characteristics. Signed-off-by:
-
David Daney authored
The UCTL clock initialization will cause the ehci and ohci blocks to become inoperable if the clocks are reinitialized. Check to see if the clocks have already been initialized. Also use a mutex to protect the clock initialization code so that there can be no attempt to use the clocks before they are fully configured. Signed-off-by:
-
Greg Kroah-Hartman authored
Merge branch 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next * 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci: xhci 1.0: Set transfer burst last packet count field. xhci 1.0: Set transfer burst count field. xhci 1.0: Update TD size field format. xhci 1.0: Only interrupt on short packet for IN EPs. xhci: Remove sparse warning about cmd_status. usbcore: warm reset USB3 port in SS.Inactive state usbcore: Refine USB3.0 device suspend and resume xHCI: report USB3.0 portstatus comply with USB3.0 specification xHCI: Set link state support xHCI: Clear link state change support xHCI: warm reset support usb/ch9: use proper endianess for wBytesPerInterval xhci: Remove recursive call to xhci_handle_event xhci: Add an assertion to check for virt_dev=0 bug. xhci: Add rmb() between reading event validity & event data access. xhci: Make xHCI driver endian-safe
-
Arvid Brodin authored
This patch replaces the code that handles qtds. Intead of directly allocating chip mem and chip slot, enqueue the transfer in a list of queue heads. Use a centralized function enqueue_qtds() to prioritize and enqueue transfers. This removes all of the interrupt context BUG() calls when out of chip mem or transfer slots. It also makes it possible to efficiently use the dual-port mem on the chip for double-buffered transfers, which improve transfer times to/from/between usb sticks by about 40 % on my HW. With this patch it should also be possible to handle qtd scheduling outside of the interrupt handler, for significantly improved kernel latency. I have not implemented this since there are some locking issues which I haven't had time to look at. Signed-off-by:
Arvid Brodin <arvid.brodin@enea.com> Signed-off-by:
-
Arvid Brodin authored
This fixes a bug in my previous (2.6.38) patch series which caused urb->status value to be wrong after unlink (broke usbtest 11, 12). Signed-off-by:
-
Arvid Brodin authored
Since we always set the OR flag for each transfer, we can just as well set all these bits to 1 at init and be done with it. Also, HcBufferStatus can be set at init as per the ISP1761 datasheet page 47 with no loss of performance. Signed-off-by:
-
Arvid Brodin authored
This collects urb enqueue code that was spread out all over the place into a couple of more readable functions. Signed-off-by:
-
Arvid Brodin authored
This removes the "qh is 0" printout. qh == NULL if the urb has been unlinked, so this condition is normal. Signed-off-by:
-
Anton Tikhomirov authored
Signed-off-by:
Anton Tikhomirov <av.tikhomirov@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Anton Tikhomirov authored
When File Storage gadget receives SET CONFIGURATION request it tries to cancel all pending transfers. If some request is in progress, gadget waits for its completion. This commit allows gadget to dequeue invalid requests in progress left after reset. Signed-off-by:
-
Anton Tikhomirov authored
The following should be done for requests after endpoint stall condition is cleared: 1) 'in progress' request (if any) should be completed since Tx FIFO was flushed; 2) next request from queue (if any) should be started. This commit does that. Additionally set/clear stall condition code is fixed. Signed-off-by:
-
Anton Tikhomirov authored
UDC driver does not need to generate reply to host if request is delivered to gadget. This is gadget's responsibility. This commit fixes that. Signed-off-by:
-
Anton Tikhomirov authored
This commit does the following: 1) clears all pending interrupts before unmasking; 2) clears interrupts as soon as possible to avoid missing next coming that may occur during handling; 3) removes ineffective interrupt cleaning code. Signed-off-by:
-
Anton Tikhomirov authored
This patch fixes code responsible for core reset. Signed-off-by:
-
