Just use MMCIF as name to match the sh7372 data sheet.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch introduces sh7372_late_devices which
should include all regular processor specific
platform devices.

Early platform devices for console and timers
should be put on the sh7372_early_devices list,
all other devices should be on sh7372_late_devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Remove duplicated include.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Fix a compile breakage, caused by my own careless copy-paste.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Currently the sh_mobile_lcdc driver only reconfigures the hardware interface,
when a new monitor is plugged in. This patch adds support for dynamic
framebuffer reconfiguration, when no user is holding the framebuffer device
node open.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Current touchpanel had below 2 issues

- LCDD2 pin which is needed for WVGA was changed to
  IRQ28_123 pin on ts_get_pendown_state

- GPIO pull up on ts_init was disabled by gpio_request
  on ts_get_pendown_state.
  This mean the return value from gpio_get_value is untrusted.

This patch solve these issues
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add video modes for 480p and SXGA (1280x1024).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

With this patch hot-plugging of an HDMI or a DVI monitor can select a different
video mode and reconfigure the LCDC and HDMI controllers accordingly. Due to a
lack of a standard API to inform framebuffer users of a changed video mode, the
framebuffer configuration is preserved regardless of a specific mode, selected
for the monitor. As described in a previous patch, this leads to smaller
framebuffers being displayed on larger monitors or a part of a larger
framebuffer being displayed on a smaller resolution monitor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

High monitor resolutions also require higher clock frequencies, current HDMI
PHY parameters do not work well for resolutions higher than 720p.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Improve comments, unify function names, replace pr_debug with dev_dbg.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is a preparation for a patch, that shall allow displaying of a smaller
framebuffer on a bigger display and of a part of a bigger framebuffer on a
smaller display.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The SH-Mobile HDMI driver runs in several contexts: ISR, delayed work-queue,
task context, when called from the sh_mobile_lcdc framebuffer driver. This
creates ample race possibilities. Even though most these races are purely
theoretical, it is better to close them. To trace fb_info validity we install a
notification callback in the HDMI driver, and the only way for it to get to
driver internal data is by using struct sh_mobile_lcdc_chan, therefore it had
to be extracted into a separate common header.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The SH-Mobile HDMI controller supports two configuration modes: using
pre-programmed VICs and the "external" mode - specifying video parameters
explicitly. The driver already contains code, necessary to configure HDMI
manually, this patch actually enables it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

To support standard video modes, other than 720p, the HDMI PHY configuration
has to be adjusted and the VIC has to be sent to the display.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Now, that we add support for multiple modes to the sh_mobile_lcdcfb driver, it
has to allocate memory, sufficient for the biggest of them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Notifier callbacks have to return either one of NOTIFY_* codes or a negative
errno, converted to a suitable value by the notifier_from_errno() inline, if
the notifier chain shall not be continued.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This is a preparation for HDMI hotplug support. This patch just moves all
platform defined video modes for the sh_mobile_lcdcfb driver to separate
arrays and switches all users to use element 0 of that array, so, this patch
doesn't introduce any functional changes and as such should not cause any
regressions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Remove an unused variable and simplify several pointer dereferences.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes the following two erroneous error paths:

hw_usecnt is allocated with a value of 0, therefore in an early error case,
calling sh_mobile_lcdc_clk_off() will wrongly conclude, that hw_usecnt has
already been incremented. Then sh_mobile_lcdc_runtime_suspend() will be called,
which will access uninitialised data fields and crash the kernel.

sh_mobile_lcdc_stop() can be called before framebuffer has been allocated, then
ch->info is NULL and dereferencing it will Oops too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The present SH-Mobile HDMI driver reads and parses the EDID block into a
variable screeninfo object, but since it is still unable to dynamically
reconfigure the framebuffer, it overwrites the EDID information with preset
values again. This patch just uses a temporary variable to store the EDID
timing information instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Use the standard fb_videomode_to_var() instead of filling fb_var_screeninfo
fields manually in, also remove a redundant memset(0).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Add ignored device name by comment-out in INTCS.
And MSIOF which has been forgotten is added
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Use evt2irq() for DMAC resources on sh7372.

This makes the code easier to read and also
allows adjusting the INTC base offset without
breaking platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Extend dip switch comments for QHD and WVGA LCD panels
on AP4EVB. Similar to the Ecovec comments.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Current gamut, acp, isrc1, isrc2 settings are wrong,
and not necessary for now.
Tested-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modify x_plate_ohms to correct value for tsc2007,
and removed un-necessary ts_get_pendown_state().
gpio_pull_up() was removed also.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Improve latencies under load by decreasing minimum scheduling granularity

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k,m68knommu: Wire up fanotify_init, fanotify_mark, and prlimit64

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix siglock

Quoth Tony:

 "I committed the fix for this last week prior to your -rc4 announcement
  reminding us to give proper "Reported-by:" credit.  This one should have
  had:
Reported-by: Tony Ernst <tee@sgi.com>

  and also
Much-useful-investigation-and-tracing-by: Hedi Berriche <hedi@sgi.com>
  Much-useful-investigation-and-tracing-by: Petr Tesarik <ptesarik@novell.com>"

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: prevent possible memory corruption in cifs_demultiplex_thread
  cifs: eliminate some more premature cifsd exits
  cifs: prevent cifsd from exiting prematurely
  [CIFS] ntlmv2/ntlmssp remove-unused-function CalcNTLMv2_partial_mac_key
  cifs: eliminate redundant xdev check in cifs_rename
  Revert "[CIFS] Fix ntlmv2 auth with ntlmssp"
  Revert "missing changes during ntlmv2/ntlmssp auth and sign"
  Revert "Eliminate sparse warning - bad constant expression"
  Revert "[CIFS] Eliminate unused variable warning"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  fs/9p: Don't use dotl version of mknod for dotu inode operations
  fs/9p: Use the correct dentry operations
  9p: Check for NULL fid in v9fs_dir_release()
  fs/9p: Fix error handling in v9fs_get_sb
  fs/9p, net/9p: memory leak fixes

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  dquot: do full inode dirty in allocating space

* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: move probe call to subsys_initcall()
  powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak
  spi/pl022: fix APB pclk power regression on U300
  spi/spi_s3c64xx: Warn if PIO transfers time out
  spi/s3c64xx: Fix incorrect reuse of 'val' local variable.
  spi/s3c64xx: Fix compilation warning
  spi/dw_spi: clean the cs_control code
  spi/dw_spi: Allow interrupt sharing
  spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer()
  spi/spi_s3c64xx: Move to subsys_initcall()
  spi: free children in spi_unregister_master, not siblings
  gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case
  of: Fix missing includes - ll_temac
  spi/spi_s3c64xx: Staticise non-exported functions
  spi/spi_s3c64xx: Make probe more robust against missing board config

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>

Mathieu reported bad latencies with make -j10 kind of kbuild
workloads - which is mostly caused by us scheduling with a
too coarse granularity.

Reduce the minimum granularity some more, to make sure we
can meet the latency target.

I got the following results (make -j10 kbuild load, average of 3
runs):

 vanilla:

  maximum latency: 38278.9 µs
  average latency:  7730.1 µs

 patched:

  maximum latency: 22702.1 µs
  average latency:  6684.8 µs

Mathieu also measured it:

|
| * wakeup-latency.c (SIGEV_THREAD) with make -j10
|
| - Mainline 2.6.35.2 kernel
|
| maximum latency: 45762.1 µs
| average latency: 7348.6 µs
|
| - With only Peter's smaller min_gran (shown below):
|
| maximum latency: 29100.6 µs
| average latency: 6684.1 µs
|
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Suggested-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <AANLkTi=8m4g01wZPacySoF7U0PevTNVgJoZZrHiUD-pN@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

We should not use dotlversion for the dotu inode operations
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

We should use the cached dentry operation only if caching mode is enabled
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>

NULL fid should be handled in cases where we endup calling v9fs_dir_release()
before even we instantiate the fid in filp.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>