VSC9959 hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. This patch support sch_cbs set for VSC9959.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ocelot VSC9959 switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. This patch add support for TAS configuration
on egress port of VSC9959 switch.

Felix driver is an instance of Ocelot family, with a DSA front-end. The
patch uses tc taprio hardware offload to setup TAS set function on felix
driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the default QoS Classification based on PCP and DEI of vlan tag,
after that, frames can be Classified to different Qos based on PCP tag.
If there is no vlan tag or vlan ignored, use port default Qos.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A comparison between a value from the packet and an integer constant
value needs to be done by converting the value from the packet from
net->host, or the constant from host->net. Not the other way around.
Even though it makes no practical difference, correct that.

Fixes: 38b5beea ("net: dsa: sja1105: prepare tagger for handling DSA tags and VLAN simultaneously")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a check to make sure the IFLA_GRE_ERSPAN_VER is provided by users.

Fixes: f989d546 ("erspan: Add type I version 0 support.")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Traffic support for dsa_8021q in vlan_filtering=1 mode

This series is an attempt to support as much as possible in terms of
traffic I/O from the network stack with the only dsa_8021q user thus
far, sja1105.

The hardware doesn't support pushing a second VLAN tag to packets that
are already tagged, so our only option is to combine the dsa_8021q with
the user tag into a single tag and decode that on the CPU.

The assumption is that there is a type of use cases for which 7 VLANs
per port are more than sufficient, and that there's another type of use
cases where the full 4096 entries are barely enough. Those use cases are
very different from one another, so I prefer trying to give both the
best experience by creating this best_effort_vlan_filtering knob to
select the mode in which they want to operate in.

v2 was submitted here:
https://patchwork.ozlabs.org/project/netdev/cover/20200511135338.20263-1-olteanv@gmail.com/

v1 was submitted here:
https://patchwork.ozlabs.org/project/netdev/cover/20200510164255.19322-1-olteanv@gmail.com/

Changes in v3:
Patch 01/15:
- Rename again to configure_vlan_while_not_filtering, and add a helper
  function for skipping VLAN configuration.
Patch 03/15:
- Remove sja1105_can_use_vlan_as_tags from driver code.
Patch 06/15:
- Adapt sja1105 driver to the second variable name change.
Patch 08/15:
- Provide an implementation of sja1105_can_use_vlan_as_tags as part of
  the tagger and not as part of the switch driver. So we have to look at
  the skb only, and not at the VLAN awareness state.

Changes in v2:
Patch 01/15:
- Rename variable from vlan_bridge_vtu to configure_vlans_while_disabled.
Patch 03/15:
- Be much more thorough, and make sure that things like virtual links
  and FDB operations still work properly.
Patch 05/15:
- Free the vlan lists on teardown.
- Simplify sja1105_classify_vlan: only look at priv->expect_dsa_8021q.
- Keep vid 1 in the list of dsa_8021q VLANs, to make sure that untagged
  packets transmitted from the stack, like PTP, continue to work in
  VLAN-unaware mode.
Patch 06/15:
- Adapt to vlan_bridge_vtu variable name change.
Patch 11/15:
- In sja1105_best_effort_vlan_filtering_set, get the vlan_filtering
  value of each port instead of just one time for port 0. Normally this
  shouldn't matter, but it avoids issues when port 0 is disabled in
  device tree.
Patch 14/14:
- Only do anything in sja1105_build_subvlans and in
  sja1105_build_crosschip_subvlans when operating in
  SJA1105_VLAN_BEST_EFFORT state. This avoids installing VLAN retagging
  rules in unaware mode, which would cost us a penalty in terms of
  usable frame memory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expand the delta commit procedure for VLANs with additional logic for
treating bridge_vlans in the newly introduced operating mode,
SJA1105_VLAN_BEST_EFFORT.

For every bridge VLAN on every user port, a sub-VLAN index is calculated
and retagging rules are installed towards a dsa_8021q rx_vid that
encodes that sub-VLAN index. This way, the tagger can identify the
original VLANs.

Extra care is taken for VLANs to still work as intended in cross-chip
scenarios. Retagging may have unintended consequences for these because
a sub-VLAN encoding that works for the CPU does not make any sense for a
front-panel port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 2 different features that require some reserved frame memory
space: VLAN retagging and virtual links. Create a central function that
modifies the static config and ensures frame memory is never
overcommitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Retagging Table is an optional feature that allows the switch to
match frames against a {ingress port, egress port, vid} rule and change
their VLAN ID. The retagged frames are by default clones of the original
ones (since the hardware-foreseen use case was to mirror traffic for
debugging purposes and to tag it with a special VLAN for this purpose),
but we can force the original frames to be dropped by removing the
pre-retagging VLAN from the port membership list of the egress port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This devlink parameter enables the handling of DSA tags when enslaved to
a bridge with vlan_filtering=1. There are very good reasons to want
this, but there are also very good reasons for not enabling it by
default. So a devlink param named best_effort_vlan_filtering, currently
driver-specific and exported only by sja1105, is used to configure this.

In practice, this is perhaps the way that most users are going to use
the switch in. It assumes that no more than 7 VLANs are needed per port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a subvlan_map as part of each port's tagger private structure.
This keeps reverse mappings of bridge-to-dsa_8021q VLAN retagging rules.

Note that as of this patch, this piece of code is never engaged, due to
the fact that the driver hasn't installed any retagging rule, so we'll
always see packets with a subvlan code of 0 (untagged).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For switches that support VLAN retagging, such as sja1105, we extend
dsa_8021q by encoding a "sub-VLAN" into the remaining 3 free bits in the
dsa_8021q tag.

A sub-VLAN is nothing more than a number in the range 0-7, which serves
as an index into a per-port driver lookup table. The sub-VLAN value of
zero means that traffic is untagged (this is also backwards-compatible
with dsa_8021q without retagging).

The switch should be configured to retag VLAN-tagged traffic that gets
transmitted towards the CPU port (and towards the CPU only). Example:

bridge vlan add dev sw1p0 vid 100

The switch retags frames received on port 0, going to the CPU, and
having VID 100, to the VID of 1104 (0x0450). In dsa_8021q language:

 | 11  | 10  |  9  |  8  |  7  |  6  |  5  |  4  |  3  |  2  |  1  |  0  |
 +-----------+-----+-----------------+-----------+-----------------------+
 |    DIR    | SVL |    SWITCH_ID    |  SUBVLAN  |          PORT         |
 +-----------+-----+-----------------+-----------+-----------------------+

0x0450 means:
 - DIR = 0b01: this is an RX VLAN
 - SUBVLAN = 0b001: this is subvlan #1
 - SWITCH_ID = 0b001: this is switch 1 (see the name "sw1p0")
 - PORT = 0b0000: this is port 0 (see the name "sw1p0")

The driver also remembers the "1 -> 100" mapping. In the hotpath, if the
sub-VLAN from the tag encodes a non-untagged frame, this mapping is used
to create a VLAN hwaccel tag, with the value of 100.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In VLAN-unaware mode, sja1105 uses VLAN tags with a custom TPID of
0xdadb. While in the yet-to-be introduced best_effort_vlan_filtering
mode, it needs to work with normal VLAN TPID values.

A complication arises when we must transmit a VLAN-tagged packet to the
switch when it's in VLAN-aware mode. We need to construct a packet with
2 VLAN tags, and the switch will use the outer header for routing and
pop it on egress. But sadly, here the 2 hardware generations don't
behave the same:

- E/T switches won't pop an ETH_P_8021AD tag on egress, it seems
  (packets will remain double-tagged).
- P/Q/R/S switches will drop a packet with 2 ETH_P_8021Q tags (it looks
  like it tries to prevent VLAN hopping).

But looks like the reverse is also true:

- E/T switches have no problem popping the outer tag from packets with
  2 ETH_P_8021Q tags.
- P/Q/R/S will have no problem popping a single tag even if that is
  ETH_P_8021AD.

So it is clear that if we want the hardware to work with dsa_8021q
tagging in VLAN-aware mode, we need to send different TPIDs depending on
revision. Keep that information in priv->info->qinq_tpid.

The per-port tagger structure will hold an xmit_tpid value that depends
not only upon the qinq_tpid, but also upon the VLAN awareness state
itself (in case we must transmit using 0xdadb).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN filtering is a global property for sja1105, and that means that we
rely on the DSA core to not call us more than once.

But we need to introduce some per-port state for the tagger, namely the
xmit_tpid, and the best place to do that is where the xmit_tpid changes,
namely in sja1105_vlan_filtering. So at the moment, exit early from the
function to avoid unnecessarily resetting the switch for each port call.
Then we'll change the xmit_tpid prior to the early exit in the next
patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let the DSA core call our .port_vlan_add methods every time the bridge
layer requests so. We will deal internally with saving/restoring VLANs
depending on our VLAN awareness state.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Managing the VLAN table that is present in hardware will become very
difficult once we add a third operating state
(best_effort_vlan_filtering). That is because correct cleanup (not too
little, not too much) becomes virtually impossible, when VLANs can be
added from the bridge layer, from dsa_8021q for basic tagging, for
cross-chip bridging, as well as retagging rules for sub-VLANs and
cross-chip sub-VLANs. So we need to rethink VLAN interaction with the
switch in a more scalable way.

In preparation for that, use the priv->expect_dsa_8021q boolean to
classify any VLAN request received through .port_vlan_add or
.port_vlan_del towards either one of 2 internal lists: bridge VLANs and
dsa_8021q VLANs.

Then, implement a central sja1105_build_vlan_table method that creates a
VLAN configuration from scratch based on the 2 lists of VLANs kept by
the driver, and based on the VLAN awareness state. Currently, if we are
VLAN-unaware, install the dsa_8021q VLANs, otherwise the bridge VLANs.

Then, implement a delta commit procedure that identifies which VLANs
from this new configuration are actually different from the config
previously committed to hardware. We apply the delta through the dynamic
configuration interface (we don't reset the switch). The result is that
the hardware should see the exact sequence of operations as before this
patch.

This also helps remove the "br" argument passed to
dsa_8021q_crosschip_bridge_join, which it was only using to figure out
whether it should commit the configuration back to us or not, based on
the VLAN awareness state of the bridge. We can simplify that, by always
allowing those VLANs inside of our dsa_8021q_vlans list, and committing
those to hardware when necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the moment, this can never happen. The 2 modes that we operate in do
not permit that:

 - SJA1105_VLAN_UNAWARE: we are guarded from bridge VLANs added by the
   user by the DSA core. We will later lift this restriction by setting
   ds->vlan_bridge_vtu = true, and that is where we'll need it.

 - SJA1105_VLAN_FILTERING_FULL: in this mode, dsa_8021q configuration is
   disabled. So the user is free to add these VLANs in the 1024-3071
   range.

The reason for the patch is that we'll introduce a third VLAN awareness
state, where both dsa_8021q as well as the bridge are going to call our
.port_vlan_add and .port_vlan_del methods.

For that, we need a good way to discriminate between the 2. The easiest
(and less intrusive way for upper layers) is to recognize the fact that
dsa_8021q configurations are always driven by our driver - we _know_
when a .port_vlan_add method will be called from dsa_8021q because _we_
initiated it.

So introduce an expect_dsa_8021q boolean which is only used, at the
moment, for blacklisting VLANs in range 1024-3071 in the modes when
dsa_8021q is active.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Soon we'll add a third operating mode to the driver. Introduce a
vlan_state to make things more easy to manage, and use it where
applicable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function returns a boolean denoting whether the VLAN passed as
argument is part of the 1024-3071 range that the dsa_8021q tagging
scheme uses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.

This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.

Provide an option that drivers can set to indicate they want to receive
vlan configuration even when vlan filtering is disabled. At the very
least, this is safe for Marvell DSA bridges, which do not look up
ingress traffic in the VTU if the port is in 8021Q disabled state. It is
also safe for the Ocelot switch family. Whether this change is suitable
for all DSA bridges is not known.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: siena_check_caps fixups

Fix a bug and a build warning introduced in a recent refactor.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Assign it to siena_a0_nic_type.check_caps function pointer.

Fixes: be904b85 ("sfc: make capability checking a nic_type function")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the UniPhier AVE4 controller binding to DT schema format.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic updates

This set of patches is a bunch of code cleanup, a little
documentation, longer tx sg lists, more ethtool stats,
and a couple more transceiver types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the basic doc file with some configuration hints and a
little bit of stats information.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add hardware port stats and a few more driver collected
statistics to the ethtool stats output.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix up a few more local names that need an "ionic" prefix.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the ionic_intr_free parameter from struct ionic_lif to
struct ionic since that's what it actually cares about.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once we're talking to the device, tell it to reset to
be sure we've got a fresh, clean environment.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shorten our msleep time while polling for the dev command
request to finish.  Yes, checkpatch.pl complains that the
msleep might actually go longer - that won't hurt, but we'll
take the shorter time if we can get it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a couple more SFP and QSFP transceiver types to our
ethtool get link ksettings.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When going into a firmware upgrade cycle, we set the device as
not present to keep some user commands from trying to change
the driver while we're only half there.  Unfortunately, the
ndo_vf_* calls don't check netif_device_present() so we need
to add a check in the callbacks.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lots of comment cleanup for better documentation, a few new
fields added, and a few minor mistakes fixed up.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The version 1 Tx queues can use longer SG lists than the
original version 0 queues, but we need to check to see if the
firmware supports the v1 Tx queues.  This implements the queue
type query for all queue types, and uses the information to
set up for using the longer Tx SG lists.

Because the Tx SG list can be longer, we need to limit the
max ring length to be sure we stay inside the boundaries of a
DMA allocation max size, so we lower the max Tx ring size.

The driver sets its highest known version in the Q_IDENTITY
command, and the FW returns the highest version that it knows,
bounded by the driver's version.  The negotiated version number
is later used in the Q_INIT commands.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ENOTSUPP often feels like the right error code to use, but it's
in fact not a standard Unix error. E.g.:

$ python
>>> import errno
>>> errno.errorcode[errno.ENOTSUPP]
Traceback (most recent call last):
  File "<stdin>", line 1, in <module>
AttributeError: module 'errno' has no attribute 'ENOTSUPP'

There were numerous commits converting the uses back to EOPNOTSUPP
but in some cases we are stuck with the high error code for backward
compatibility reasons.

Let's try prevent more ENOTSUPPs from getting into the kernel.

Recent example:
https://lore.kernel.org/netdev/20200510182252.GA411829@lunn.ch/

v3 (Joe):
 - fix the "not file" condition.

v2 (Joe):
 - add a link to recent discussion,
 - don't match when scanning files, not patches to avoid sudden
   influx of conversion patches.
https://lore.kernel.org/netdev/20200511165319.2251678-1-kuba@kernel.org/

v1:
https://lore.kernel.org/netdev/20200510185148.2230767-1-kuba@kernel.org/Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christoph Hellwig says:

====================
improve msg_control kernel vs user pointer handling

this series replace the msg_control in the kernel msghdr structure
with an anonymous union and separate fields for kernel vs user
pointers.  In addition to helping a bit with type safety and reducing
sparse warnings, this also allows to remove the set_fs() in
kernel_recvmsg, helping with an eventual entire removal of set_fs().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The msg_control field in struct msghdr can either contain a user
pointer when used with the recvmsg system call, or a kernel pointer
when used with sendmsg.  To complicate things further kernel_recvmsg
can stuff a kernel pointer in and then use set_fs to make the uaccess
helpers accept it.

Replace it with a union of a kernel pointer msg_control field, and
a user pointer msg_control_user one, and allow kernel_recvmsg operate
on a proper kernel pointer using a bitfield to override the normal
choice of a user pointer for recvmsg.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out two helpes to keep the code tidy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>