- 05 Apr, 2019 40 commits
-
-
Sara Sharon authored
[ Upstream commit c6ac9f9f ] Allocator swaps the pending requests with 0 when it starts working. This means that relying on it n RX path to decide if to move to emergency is not always a good idea, since it may be zero, but there are still a lot of unallocated RBs in the system. Change allocator to decrement the pending requests on real time. It is more expensive since it accesses the atomic variable more times, but it gives the RX path a better idea of the system's status. Reported-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
Sara Sharon <sara.sharon@intel.com> Fixes: 868a1e86 ("iwlwifi: pcie: avoid empty free RB queue") Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Michal Kazior authored
[ Upstream commit 5ddb0869 ] I've stumbled upon a kernel crash and the logs pointed me towards the lp5562 driver: > <4>[306013.841294] lp5562 0-0030: Direct firmware load for lp5562 failed with error -2 > <4>[306013.894990] lp5562 0-0030: Falling back to user helper > ... > <3>[306073.924886] lp5562 0-0030: firmware request failed > <1>[306073.939456] Unable to handle kernel NULL pointer dereference at virtual address 00000000 > <4>[306074.251011] PC is at _raw_spin_lock+0x1c/0x58 > <4>[306074.255539] LR is at release_firmware+0x6c/0x138 > ... After taking a look I noticed firmware_release() could be called with either NULL or a dangling pointer. Fixes: 10c06d17 ("leds-lp55xx: support firmware interface") Signed-off-by:
Michal Kazior <michal@plume.com> Signed-off-by:
Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by:
-
Theodore Ts'o authored
[ Upstream commit 538bcaa6 ] The jbd2 superblock is lockless now, so there is probably a race condition between writing it so disk and modifing contents of it, which may lead to checksum error. The following race is the one case that we have captured. jbd2 fsstress jbd2_journal_commit_transaction jbd2_journal_update_sb_log_tail jbd2_write_superblock jbd2_superblock_csum_set jbd2_journal_revoke jbd2_journal_set_features(revork) modify superblock submit_bh(checksum incorrect) Fix this by locking the buffer head before modifing it. We always write the jbd2 superblock after we modify it, so this just means calling the lock_buffer() a little earlier. This checksum corruption problem can be reproduced by xfstests generic/475. Reported-by:
zhangyi (F) <yi.zhang@huawei.com> Suggested-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Hong Liu authored
[ Upstream commit 0d28f494 ] When performing a warm reset in ishtp bus driver, the ishtp_cl_device will not be removed, its fw_client still points to the already freed ishtp_device.fw_clients array. Later after driver finishing ishtp client enumeration, this dangling pointer may cause driver to bind the wrong ishtp_cl_device to the new client, causing wrong callback to be called for messages intended for the new client. This helps in development of firmware where frequent switching of firmwares is required without Linux reboot. Signed-off-by:
Hong Liu <hong.liu@intel.com> Tested-by:
Hongyan Song <hongyan.song@intel.com> Acked-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Aurelien Jarno authored
[ Upstream commit cc4b1242 ] The preadv2 and pwritev2 syscalls are supposed to emulate the readv and writev syscalls when offset == -1. Therefore the compat code should check for offset before calling do_compat_preadv64 and do_compat_pwritev64. This is the case for the preadv2 and pwritev2 syscalls, but handling of offset == -1 is missing in their 64-bit equivalent. This patch fixes that, calling do_compat_readv and do_compat_writev when offset == -1. This fixes the following glibc tests on x32: - misc/tst-preadvwritev2 - misc/tst-preadvwritev64v2 Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: H.J. Lu <hjl.tools@gmail.com> Signed-off-by:
Aurelien Jarno <aurelien@aurel32.net> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Ezequiel Garcia authored
[ Upstream commit 1b275e4e ] Fix the assigned type of mem2mem buffer handling API. Namely, these functions: v4l2_m2m_next_buf v4l2_m2m_last_buf v4l2_m2m_buf_remove v4l2_m2m_next_src_buf v4l2_m2m_next_dst_buf v4l2_m2m_last_src_buf v4l2_m2m_last_dst_buf v4l2_m2m_src_buf_remove v4l2_m2m_dst_buf_remove return a struct vb2_v4l2_buffer, and not a struct vb2_buffer. Fixing this is necessary to fix the mem2mem buffer handling API, changing the return to the correct struct vb2_v4l2_buffer instead of a void pointer. Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
Ezequiel Garcia authored
[ Upstream commit 8d20dcef ] Fix the assigned type of mem2mem buffer handling API. Namely, these functions: v4l2_m2m_next_buf v4l2_m2m_last_buf v4l2_m2m_buf_remove v4l2_m2m_next_src_buf v4l2_m2m_next_dst_buf v4l2_m2m_last_src_buf v4l2_m2m_last_dst_buf v4l2_m2m_src_buf_remove v4l2_m2m_dst_buf_remove return a struct vb2_v4l2_buffer, and not a struct vb2_buffer. Fixing this is necessary to fix the mem2mem buffer handling API, changing the return to the correct struct vb2_v4l2_buffer instead of a void pointer. Signed-off-by:
-
Ezequiel Garcia authored
[ Upstream commit 30fa627b ] Fix the assigned type of mem2mem buffer handling API. Namely, these functions: v4l2_m2m_next_buf v4l2_m2m_last_buf v4l2_m2m_buf_remove v4l2_m2m_next_src_buf v4l2_m2m_next_dst_buf v4l2_m2m_last_src_buf v4l2_m2m_last_dst_buf v4l2_m2m_src_buf_remove v4l2_m2m_dst_buf_remove return a struct vb2_v4l2_buffer, and not a struct vb2_buffer. Fixing this is necessary to fix the mem2mem buffer handling API, changing the return to the correct struct vb2_v4l2_buffer instead of a void pointer. Signed-off-by:
-
Ezequiel Garcia authored
[ Upstream commit 4a88f898 ] Fix the assigned type of mem2mem buffer handling API. Namely, these functions: v4l2_m2m_next_buf v4l2_m2m_last_buf v4l2_m2m_buf_remove v4l2_m2m_next_src_buf v4l2_m2m_next_dst_buf v4l2_m2m_last_src_buf v4l2_m2m_last_dst_buf v4l2_m2m_src_buf_remove v4l2_m2m_dst_buf_remove return a struct vb2_v4l2_buffer, and not a struct vb2_buffer. Fixing this is necessary to fix the mem2mem buffer handling API, changing the return to the correct struct vb2_v4l2_buffer instead of a void pointer. Signed-off-by:
-
Ezequiel Garcia authored
[ Upstream commit 43c14519 ] Fix the assigned type of mem2mem buffer handling API. Namely, these functions: v4l2_m2m_next_buf v4l2_m2m_last_buf v4l2_m2m_buf_remove v4l2_m2m_next_src_buf v4l2_m2m_next_dst_buf v4l2_m2m_last_src_buf v4l2_m2m_last_dst_buf v4l2_m2m_src_buf_remove v4l2_m2m_dst_buf_remove return a struct vb2_v4l2_buffer, and not a struct vb2_buffer. Fixing this is necessary to fix the mem2mem buffer handling API, changing the return to the correct struct vb2_v4l2_buffer instead of a void pointer. Signed-off-by:
-
Wen Yang authored
[ Upstream commit 8fa857da ] The of_find_device_by_node() takes a reference to the underlying device structure, we should release that reference. Detected by coccinelle with the following warnings: ./sound/soc/fsl/imx-sgtl5000.c:169:1-7: ERROR: missing put_device; call of_find_device_by_node on line 105, but without a corresponding object release within this function. ./sound/soc/fsl/imx-sgtl5000.c:177:1-7: ERROR: missing put_device; call of_find_device_by_node on line 105, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <yellowriver2010@hotmail.com> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Thomas Richter authored
[ Upstream commit 03d30971 ] Commit 489338a7 ("perf tests evsel-tp-sched: Fix bitwise operator") causes test case 14 "Parse sched tracepoints fields" to fail on s390. This test succeeds on x86. In fact this test now fails on all architectures with type char treated as type unsigned char. The root cause is the signed-ness of character arrays in the tracepoints sched_switch for structure members prev_comm and next_comm. On s390 the output of: [root@m35lp76 perf]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format name: sched_switch ID: 287 format: field:unsigned short common_type; offset:0; size:2; signed:0; ... field:char prev_comm[16]; offset:8; size:16; signed:0; ... field:char next_comm[16]; offset:40; size:16; signed:0; reveals the character arrays prev_comm and next_comm are per default unsigned char and have values in the range of 0..255. On x86 both fields are signed as this output shows: [root@f29]# cat /sys/kernel/debug/tracing/events/sched/sched_switch/format name: sched_switch ID: 287 format: field:unsigned short common_type; offset:0; size:2; signed:0; ... field:char prev_comm[16]; offset:8; size:16; signed:1; ... field:char next_comm[16]; offset:40; size:16; signed:1; and the character arrays prev_comm and next_comm are per default signed char and have values in the range of -1..127. The implementation of type char is architecture specific. Since the character arrays in both tracepoints sched_switch and sched_wakeup should contain ascii characters, simply omit the check for signedness in the test case. Output before: [root@m35lp76 perf]# ./perf test -F 14 14: Parse sched tracepoints fields : --- start --- sched:sched_switch: "prev_comm" signedness(0) is wrong, should be 1 sched:sched_switch: "next_comm" signedness(0) is wrong, should be 1 sched:sched_wakeup: "comm" signedness(0) is wrong, should be 1 ---- end ---- 14: Parse sched tracepoints fields : FAILED! [root@m35lp76 perf]# Output after: [root@m35lp76 perf]# ./perf test -Fv 14 14: Parse sched tracepoints fields : --- start --- ---- end ---- Parse sched tracepoints fields: Ok [root@m35lp76 perf]# Fixes: 489338a7 ("perf tests evsel-tp-sched: Fix bitwise operator") Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Link: http://lkml.kernel.org/r/20190219153639.31267-1-tmricht@linux.ibm.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Sedat Dilek authored
[ Upstream commit 8beb90aa ] commit 1917d42d ("fcoe: use enum for fip_mode") introduces a separate enum for the fip_mode that shall be used during initialisation handling until it is passed to fcoe_ctrl_link_up to set the initial fip_state. That change was incomplete and gcc quietly converted in various places between the fip_mode and the fip_state enum values with implicit enum conversions, which fortunately cannot cause any issues in the actual code's execution. clang however warns about these implicit enum conversions in the scsi drivers. This commit consolidates the use of the two enums, guided by clang's enum-conversion warnings. This commit now completes the use of the fip_mode: It expects and uses fip_mode in {bnx2fc,fcoe}_interface_create and fcoe_ctlr_init, and it calls fcoe_ctrl_set_set() with the correct values in fcoe_ctlr_link_up(). It also breaks the association between FIP_MODE_AUTO and FIP_ST_AUTO to indicate these two enums are distinct. Link: https://github.com/ClangBuiltLinux/linux/issues/151 Fixes: 1917d42d ("fcoe: use enum for fip_mode") Reported-by:
Dmitry Golovin <dima@golovin.in> Original-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> CC: Lukas Bulwahn <lukas.bulwahn@gmail.com> CC: Nick Desaulniers <ndesaulniers@google.com> CC: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Nathan Chancellor <natechancellor@gmail.com> Tested-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Jason Yan authored
[ Upstream commit bcf3b67d ] when create DMA pool for cmd frames failed, we should return -ENOMEM, instead of 0. In some case in: megasas_init_adapter_fusion() -->megasas_alloc_cmds() -->megasas_create_frame_pool create DMA pool failed, --> megasas_free_cmds() [1] -->megasas_alloc_cmds_fusion() failed, then goto fail_alloc_cmds. -->megasas_free_cmds() [2] we will call megasas_free_cmds twice, [1] will kfree cmd_list, [2] will use cmd_list.it will cause a problem: Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = ffffffc000f70000 [00000000] *pgd=0000001fbf893003, *pud=0000001fbf893003, *pmd=0000001fbf894003, *pte=006000006d000707 Internal error: Oops: 96000005 [#1] SMP Modules linked in: CPU: 18 PID: 1 Comm: swapper/0 Not tainted task: ffffffdfb9290000 ti: ffffffdfb923c000 task.ti: ffffffdfb923c000 PC is at megasas_free_cmds+0x30/0x70 LR is at megasas_free_cmds+0x24/0x70 ... Call trace: [<ffffffc0005b779c>] megasas_free_cmds+0x30/0x70 [<ffffffc0005bca74>] megasas_init_adapter_fusion+0x2f4/0x4d8 [<ffffffc0005b926c>] megasas_init_fw+0x2dc/0x760 [<ffffffc0005b9ab0>] megasas_probe_one+0x3c0/0xcd8 [<ffffffc0004a5abc>] local_pci_probe+0x4c/0xb4 [<ffffffc0004a5c40>] pci_device_probe+0x11c/0x14c [<ffffffc00053a5e4>] driver_probe_device+0x1ec/0x430 [<ffffffc00053a92c>] __driver_attach+0xa8/0xb0 [<ffffffc000538178>] bus_for_each_dev+0x74/0xc8 [<ffffffc000539e88>] driver_attach+0x28/0x34 [<ffffffc000539a18>] bus_add_driver+0x16c/0x248 [<ffffffc00053b234>] driver_register+0x6c/0x138 [<ffffffc0004a5350>] __pci_register_driver+0x5c/0x6c [<ffffffc000ce3868>] megasas_init+0xc0/0x1a8 [<ffffffc000082a58>] do_one_initcall+0xe8/0x1ec [<ffffffc000ca7be8>] kernel_init_freeable+0x1c8/0x284 [<ffffffc0008d90b8>] kernel_init+0x1c/0xe4 Signed-off-by:
Jason Yan <yanaijie@huawei.com> Acked-by:
Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit 45b14a4f ] When checking a generic status block, we iterate over all the generic data blocks. The loop condition only checks that the start of the generic data block is valid (within estatus->data_length) but not the whole block. Because the size of data blocks (excluding error data) may vary depending on the revision and the revision is contained within the data block, ensure that enough of the current data block is valid before dereferencing any members otherwise an out-of-bounds access may occur if estatus->data_length is invalid. This relies on the fact that struct acpi_hest_generic_data_v300 is a superset of the earlier version. Also rework the other checks to avoid potential underflow. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Borislav Petkov <bp@suse.de> Tested-by:
Tyler Baicar <baicar.tyler@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Erwan Velu authored
[ Upstream commit 1222d527 ] There is some rare cases where CPB (and possibly IDA) are missing on processors. This is the case fixed by commit f7f3dc00 ("x86/cpu/AMD: Fix erratum 1076 (CPB bit)") and following. In such context, the boost status isn't reported by /sys/devices/system/cpu/cpufreq/boost. This commit is about printing a message to report that the CPU doesn't expose the boost capabilities. This message could help debugging platforms hit by this phenomena. Signed-off-by:
Erwan Velu <e.velu@criteo.com> [ rjw: Change the message text somewhat ] Signed-off-by:
-
Katsuhiro Suzuki authored
[ Upstream commit d13501a2 ] Custom approximation of fractional-divider may not need parent clock rate checking. For example Rockchip SoCs work fine using grand parent clock rate even if target rate is greater than parent. This patch checks parent clock rate only if CLK_SET_RATE_PARENT flag is set. For detailed example, clock tree of Rockchip I2S audio hardware. - Clock rate of CPLL is 1.2GHz, GPLL is 491.52MHz. - i2s1_div is integer divider can divide N (N is 1~128). Input clock is CPLL or GPLL. Initial divider value is N = 1. Ex) PLL = CPLL, N = 10, i2s1_div output rate is CPLL / 10 = 1.2GHz / 10 = 120MHz - i2s1_frac is fractional divider can divide input to x/y, x and y are 16bit integer. CPLL --> | selector | ---> i2s1_div -+--> | selector | --> I2S1 MCLK GPLL --> | | ,--------------' | | `--> i2s1_frac ---> | | Clock mux system try to choose suitable one from i2s1_div and i2s1_frac for master clock (MCLK) of I2S1. Bad scenario as follows: - Try to set MCLK to 8.192MHz (32kHz audio replay) Candidate setting is - i2s1_div: GPLL / 60 = 8.192MHz i2s1_div candidate is exactly same as target clock rate, so mux choose this clock source. i2s1_div output rate is changed 491.52MHz -> 8.192MHz - After that try to set to 11.2896MHz (44.1kHz audio replay) Candidate settings are - i2s1_div : CPLL / 107 = 11.214945MHz - i2s1_frac: i2s1_div = 8.192MHz This is because clk_fd_round_rate() thinks target rate (11.2896MHz) is higher than parent rate (i2s1_div = 8.192MHz) and returns parent clock rate. Above is current upstreamed behavior. Clock mux system choose i2s1_div, but this clock rate is not acceptable for I2S driver, so users cannot replay audio. Expected behavior is: - Try to set master clock to 11.2896MHz (44.1kHz audio replay) Candidate settings are - i2s1_div : CPLL / 107 = 11.214945MHz - i2s1_frac: i2s1_div * 147/6400 = 11.2896MHz Change i2s1_div to GPLL / 1 = 491.52MHz at same time. If apply this commit, clk_fd_round_rate() calls custom approximate function of Rockchip even if target rate is higher than parent. Custom function changes both grand parent (i2s1_div) and parent (i2s_frac) settings at same time. Clock mux system can choose i2s1_frac and audio works fine. Signed-off-by:
Katsuhiro Suzuki <katsuhiro@katsuster.net> Reviewed-by:
Heiko Stuebner <heiko@sntech.de> [sboyd@kernel.org: Make function into a macro instead] Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Håkon Bugge authored
[ Upstream commit 2612d723 ] Using CX-3 virtual functions, either from a bare-metal machine or pass-through from a VM, MAD packets are proxied through the PF driver. Since the VF drivers have separate name spaces for MAD Transaction Ids (TIDs), the PF driver has to re-map the TIDs and keep the book keeping in a cache. Following the RDMA Connection Manager (CM) protocol, it is clear when an entry has to evicted form the cache. But life is not perfect, remote peers may die or be rebooted. Hence, it's a timeout to wipe out a cache entry, when the PF driver assumes the remote peer has gone. During workloads where a high number of QPs are destroyed concurrently, excessive amount of CM DREQ retries has been observed The problem can be demonstrated in a bare-metal environment, where two nodes have instantiated 8 VFs each. This using dual ported HCAs, so we have 16 vPorts per physical server. 64 processes are associated with each vPort and creates and destroys one QP for each of the remote 64 processes. That is, 1024 QPs per vPort, all in all 16K QPs. The QPs are created/destroyed using the CM. When tearing down these 16K QPs, excessive CM DREQ retries (and duplicates) are observed. With some cat/paste/awk wizardry on the infiniband_cm sysfs, we observe as sum of the 16 vPorts on one of the nodes: cm_rx_duplicates: dreq 2102 cm_rx_msgs: drep 1989 dreq 6195 rep 3968 req 4224 rtu 4224 cm_tx_msgs: drep 4093 dreq 27568 rep 4224 req 3968 rtu 3968 cm_tx_retries: dreq 23469 Note that the active/passive side is equally distributed between the two nodes. Enabling pr_debug in cm.c gives tons of: [171778.814239] <mlx4_ib> mlx4_ib_multiplex_cm_handler: id{slave: 1,sl_cm_id: 0xd393089f} is NULL! By increasing the CM_CLEANUP_CACHE_TIMEOUT from 5 to 30 seconds, the tear-down phase of the application is reduced from approximately 90 to 50 seconds. Retries/duplicates are also significantly reduced: cm_rx_duplicates: dreq 2460 [] cm_tx_retries: dreq 3010 req 47 Increasing the timeout further didn't help, as these duplicates and retries stems from a too short CMA timeout, which was 20 (~4 seconds) on the systems. By increasing the CMA timeout to 22 (~17 seconds), the numbers fell down to about 10 for both of them. Adjustment of the CMA timeout is not part of this commit. Signed-off-by:
Håkon Bugge <haakon.bugge@oracle.com> Acked-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit ab2c4e25 ] Give precision identifiers to the two snprintf() formatting the priority and TC strings to avoid producing these two warnings: drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function 'mlxsw_sp_port_get_prio_strings': drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d' directive output may be truncated writing between 1 and 3 bytes into a region of size between 0 and 31 [-Wformat-truncation=] snprintf(*p, ETH_GSTRING_LEN, "%s_%d", ^~ drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf' output between 3 and 36 bytes into a destination of size 32 snprintf(*p, ETH_GSTRING_LEN, "%s_%d", ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ mlxsw_sp_port_hw_prio_stats[i].str, prio); ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function 'mlxsw_sp_port_get_tc_strings': drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d' directive output may be truncated writing between 1 and 11 bytes into a region of size between 0 and 31 [-Wformat-truncation=] snprintf(*p, ETH_GSTRING_LEN, "%s_%d", ^~ drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf' output between 3 and 44 bytes into a destination of size 32 snprintf(*p, ETH_GSTRING_LEN, "%s_%d", ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ mlxsw_sp_port_hw_tc_stats[i].str, tc); ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 135e7245 ] Provide precision hints to snprintf() since we know the destination buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the following warnings: drivers/net/ethernet/intel/e1000e/netdev.c: In function 'e1000_request_msix': drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf' output may be truncated before the last format character [-Wformat-truncation=] "%s-rx-0", netdev->name); ^ drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf' output between 6 and 21 bytes into a destination of size 20 snprintf(adapter->rx_ring->name, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ sizeof(adapter->rx_ring->name) - 1, ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ "%s-rx-0", netdev->name); ~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf' output may be truncated before the last format character [-Wformat-truncation=] "%s-tx-0", netdev->name); ^ drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf' output between 6 and 21 bytes into a destination of size 20 snprintf(adapter->tx_ring->name, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ sizeof(adapter->tx_ring->name) - 1, ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ "%s-tx-0", netdev->name); ~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by:
-
Aaro Koskinen authored
[ Upstream commit a6327b5e ] When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy: MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! MMC: CTO of 0xff and 0xfe cannot be used! [ad inf.] Emulator warnings appear to be valid. The TI document SPRU680 [1] ("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card (MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253 cycles and "0xff and 0xfe cannot be used". Fix by using 0xfd as the maximum timeout. Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810 (OMAP2420) that MMC works as before. [1] http://www.ti.com/lit/ug/spru680/spru680.pdf Fixes: 730c9b7e ("[MMC] Add OMAP MMC host driver") Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Aneesh Kumar K.V authored
[ Upstream commit 5330367f ] After we ALIGN up the address we need to make sure we didn't overflow and resulted in zero address. In that case, we need to make sure that the returned address is greater than mmap_min_addr. This fixes selftest va_128TBswitch --run-hugetlb reporting failures when run as non root user for mmap(-1, MAP_HUGETLB) The bug is that a non-root user requesting address -1 will be given address 0 which will then fail, whereas they should have been given something else that would have succeeded. We also avoid the first mmap(-1, MAP_HUGETLB) returning NULL address as mmap address with this change. So we think this is not a security issue, because it only affects whether we choose an address below mmap_min_addr, not whether we actually allow that address to be mapped. ie. there are existing capability checks to prevent a user mapping below mmap_min_addr and those will still be honoured even without this fix. Fixes: 48483760 ("powerpc/mm: Add radix support for hugetlb") Reviewed-by:
Laurent Dufour <ldufour@linux.vnet.ibm.com> Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Nicolas Boichat authored
[ Upstream commit 032ebd85 ] L1 tables are allocated with __get_dma_pages, and therefore already ignored by kmemleak. Without this, the kernel would print this error message on boot, when the first L1 table is allocated: [ 2.810533] kmemleak: Trying to color unknown object at 0xffffffd652388000 as Black [ 2.818190] CPU: 5 PID: 39 Comm: kworker/5:0 Tainted: G S 4.19.16 #8 [ 2.831227] Workqueue: events deferred_probe_work_func [ 2.836353] Call trace: ... [ 2.852532] paint_ptr+0xa0/0xa8 [ 2.855750] kmemleak_ignore+0x38/0x6c [ 2.859490] __arm_v7s_alloc_table+0x168/0x1f4 [ 2.863922] arm_v7s_alloc_pgtable+0x114/0x17c [ 2.868354] alloc_io_pgtable_ops+0x3c/0x78 ... Fixes: e5fc9753 ("iommu/io-pgtable: Add ARMv7 short descriptor support") Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Sebastian Andrzej Siewior authored
[ Upstream commit 74ffe79a ] Mostly unwind is done with irqs enabled however SLUB may call it with irqs disabled while creating a new SLUB cache. I had system freeze while loading a module which called kmem_cache_create() on init. That means SLUB's __slab_alloc() disabled interrupts and then ->new_slab_objects() ->new_slab() ->setup_object() ->setup_object_debug() ->init_tracking() ->set_track() ->save_stack_trace() ->save_stack_trace_tsk() ->walk_stackframe() ->unwind_frame() ->unwind_find_idx() =>spin_lock_irqsave(&unwind_lock); Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Lubomir Rintel authored
[ Upstream commit fe9ed6d2 ] Like the other OF-enabled drivers, use the port number from the firmware if the devicetree specifies an alias: aliases { ... serial2 = &uart2; /* Should be ttyS2 */ } This is how the deprecated pxa.c driver behaved, switching to 8250_pxa messes up the numbering. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Sai Prakash Ranjan authored
[ Upstream commit 5666dfd1 ] SDM845 has ETMv4.2 and can use the existing etm4x driver. But the current etm driver checks only for ETMv4.0 and errors out for other etm4x versions. This patch adds this missing support to enable SoC's with ETMv4x to use same driver by checking only the ETM architecture major version number. Without this change, we get below error during etm probe: / # dmesg | grep etm [ 6.660093] coresight-etm4x: probe of 7040000.etm failed with error -22 [ 6.666902] coresight-etm4x: probe of 7140000.etm failed with error -22 [ 6.673708] coresight-etm4x: probe of 7240000.etm failed with error -22 [ 6.680511] coresight-etm4x: probe of 7340000.etm failed with error -22 [ 6.687313] coresight-etm4x: probe of 7440000.etm failed with error -22 [ 6.694113] coresight-etm4x: probe of 7540000.etm failed with error -22 [ 6.700914] coresight-etm4x: probe of 7640000.etm failed with error -22 [ 6.707717] coresight-etm4x: probe of 7740000.etm failed with error -22 With this change, etm probe is successful: / # dmesg | grep etm [ 6.659198] coresight-etm4x 7040000.etm: CPU0: ETM v4.2 initialized [ 6.665848] coresight-etm4x 7140000.etm: CPU1: ETM v4.2 initialized [ 6.672493] coresight-etm4x 7240000.etm: CPU2: ETM v4.2 initialized [ 6.679129] coresight-etm4x 7340000.etm: CPU3: ETM v4.2 initialized [ 6.685770] coresight-etm4x 7440000.etm: CPU4: ETM v4.2 initialized [ 6.692403] coresight-etm4x 7540000.etm: CPU5: ETM v4.2 initialized [ 6.699024] coresight-etm4x 7640000.etm: CPU6: ETM v4.2 initialized [ 6.705646] coresight-etm4x 7740000.etm: CPU7: ETM v4.2 initialized Signed-off-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit e7140639 ] When building with -Wsometimes-uninitialized, Clang warns: arch/powerpc/xmon/ppc-dis.c:157:7: warning: variable 'opcode' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] if (cpu_has_feature(CPU_FTRS_POWER9)) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/xmon/ppc-dis.c:167:7: note: uninitialized use occurs here if (opcode == NULL) ^~~~~~ arch/powerpc/xmon/ppc-dis.c:157:3: note: remove the 'if' if its condition is always true if (cpu_has_feature(CPU_FTRS_POWER9)) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ arch/powerpc/xmon/ppc-dis.c:132:38: note: initialize the variable 'opcode' to silence this warning const struct powerpc_opcode *opcode; ^ = NULL 1 warning generated. This warning seems to make no sense on the surface because opcode is set to NULL right below this statement. However, there is a comma instead of semicolon to end the dialect assignment, meaning that the opcode assignment only happens in the if statement. Properly terminate that line so that Clang no longer warns. Fixes: 5b102782 ("powerpc/xmon: Enable disassembly files (compilation changes)") Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Benjamin Block authored
[ Upstream commit 1749ef00 ] We had a test-report where, under memory pressure, adding LUNs to the systems would fail (the tests add LUNs strictly in sequence): [ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5 [ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS [ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43 [ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0 [ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection [ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB) [ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off [ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08 [ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5525.857838] sdk: sdk1 [ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk [ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds [ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA [ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA [ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA [ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured [ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured Looking at the code of scsi_alloc_sdev(), and all the calling contexts, there seems to be no reason to use GFP_ATMOIC here. All the different call-contexts use a mutex at some point, and nothing in between that requires no sleeping, as far as I could see. Additionally, the code that later allocates the block queue for the device (scsi_mq_alloc_queue()) already uses GFP_KERNEL. There are similar allocations in two other functions: scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with GFP_KERNEL. Here is the contexts for the three functions so far: scsi_alloc_sdev() scsi_probe_and_add_lun() scsi_sequential_lun_scan() __scsi_scan_target() scsi_scan_target() mutex_lock() scsi_scan_channel() scsi_scan_host_selected() mutex_lock() scsi_report_lun_scan() __scsi_scan_target() ... __scsi_add_device() mutex_lock() __scsi_scan_target() ... scsi_report_lun_scan() ... scsi_get_host_dev() mutex_lock() scsi_probe_and_add_lun() ... scsi_add_lun() scsi_probe_and_add_lun() ... So replace all these, and give them a bit of a better chance to succeed, with more chances of reclaim. Signed-off-by:
Benjamin Block <bblock@linux.ibm.com> Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
Paul Kocialkowski authored
[ Upstream commit 68ef2362 ] According to the chipidea driver bindings, the USB PHY is specified via the "phys" phandle node. However, this only takes effect for USB PHYs that use the common PHY framework. For legacy USB PHYs, a simple lookup based on the USB PHY type is done instead. This does not play out well when more than one USB PHY is registered, since the first registered PHY matching the type will always be returned regardless of what the driver was bound to. Fix this by looking up the PHY based on the "phys" phandle node. Although generic PHYs are rather matched by their "phys-name" and not the "phys" phandle directly, there is no helper for similar lookup on legacy PHYs and it's probably not worth the effort to add it. When no legacy USB PHY is found by phandle, fallback to grabbing any registered USB2 PHY. This ensures backward compatibility if some users were actually relying on this mechanism. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Eric Biggers authored
[ Upstream commit 41798036 ] The cavium/zip implementation of the deflate compression algorithm is incorrectly being registered under the generic driver name, which prevents the generic implementation from being registered with the crypto API when CONFIG_CRYPTO_DEV_CAVIUM_ZIP=y. Similarly the lzs algorithm (which does not currently have a generic implementation...) is incorrectly being registered as lzs-generic. Fix the naming collision by adding a suffix "-cavium" to the cra_driver_name of the cavium/zip algorithms. Fixes: 640035a2 ("crypto: zip - Add ThunderX ZIP driver core") Cc: Mahipal Challa <mahipalreddy2006@gmail.com> Cc: Jan Glauber <jglauber@cavium.com> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Julia Lawall authored
[ Upstream commit 8c2b43d2 ] Add an of_node_put when a tested device node is not available. The semantic patch that fixes this problem is as follows (http://coccinelle.lip6.fr): // <smpl> @@ identifier f; local idexpression e; expression x; @@ e = f(...); ... when != of_node_put(e) when != x = e when != e = x when any if (<+...of_device_is_available(e)...+>) { ... when != of_node_put(e) ( return e; | + of_node_put(e); return ...; ) } // </smpl> Fixes: 5343e674 ("crypto4xx: integrate ppc4xx-rng into crypto4xx") Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Alexei Avshalom Lazar authored
[ Upstream commit de77a53c ] ies1 or ies2 might be null when code inside _wil_cfg80211_merge_extra_ies access them. Add explicit check for null and make sure ies1/ies2 are not accessed in such a case. spos might be null and be accessed inside _wil_cfg80211_merge_extra_ies. Add explicit check for null in the while condition statement and make sure spos is not accessed in such a case. Signed-off-by:
Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by:
Maya Erez <merez@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Rafael J. Wysocki authored
[ Upstream commit 95c80bc6 ] Dongdong reported a deadlock triggered by a hotplug event during a sysfs "remove" operation: pciehp 0000:00:0c.0:pcie004: Slot(0-1): Link Up # echo 1 > 0000:00:0c.0/remove PME and hotplug share an MSI/MSI-X vector. The sysfs "remove" side is: remove_store pci_stop_and_remove_bus_device_locked pci_lock_rescan_remove pci_stop_and_remove_bus_device ... pcie_pme_remove pcie_pme_suspend synchronize_irq # wait for hotplug IRQ handler pci_unlock_rescan_remove The hotplug side is: pciehp_ist pciehp_handle_presence_or_link_change pciehp_configure_device pci_lock_rescan_remove # wait for pci_unlock_rescan_remove() INFO: task bash:10913 blocked for more than 120 seconds. # ps -ax |grep D PID TTY STAT TIME COMMAND 10913 ttyAMA0 Ds+ 0:00 -bash 14022 ? D 0:00 [irq/745-pciehp] # cat /proc/14022/stack __switch_to+0x94/0xd8 pci_lock_rescan_remove+0x20/0x28 pciehp_configure_device+0x30/0x140 pciehp_handle_presence_or_link_change+0x324/0x458 pciehp_ist+0x1dc/0x1e0 # cat /proc/10913/stack __switch_to+0x94/0xd8 synchronize_irq+0x8c/0xc0 pcie_pme_suspend+0xa4/0x118 pcie_pme_remove+0x20/0x40 pcie_port_remove_service+0x3c/0x58 ... pcie_port_device_remove+0x2c/0x48 pcie_portdrv_remove+0x68/0x78 pci_device_remove+0x48/0x120 ... pci_stop_bus_device+0x84/0xc0 pci_stop_and_remove_bus_device_locked+0x24/0x40 remove_store+0xa4/0xb8 dev_attr_store+0x44/0x60 sysfs_kf_write+0x58/0x80 It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two reasons. First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the native hotplug interrupt handler as well as for the PME one, because they share one IRQ (as per the spec). That may deadlock if hotplug is signaled while pcie_pme_remove() is running and the latter calls pci_lock_rescan_remove() before the former. Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled for the port, it will return without disabling the interrupt as expected by pcie_pme_remove() which was overlooked by commit c7b5a4e6 ("PCI / PM: Fix native PME handling during system suspend/resume"). To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear its status and prevent the PME worker function from re-enabling it before calling free_irq() on it, which should be sufficient. Fixes: c7b5a4e6 ("PCI / PM: Fix native PME handling during system suspend/resume") Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.comReported-by:
Dongdong Liu <liudongdong3@huawei.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Tony Jones authored
[ Upstream commit 7c5b019e ] Fix buffer overflow observed when running perf test. The overflow is when trying to evaluate "1ULL << (64 - 1)" which is resulting in -9223372036854775808 which overflows the 20 character buffer. If is possible this bug has been reported before but I still don't see any fix checked in: See: https://www.spinics.net/lists/linux-perf-users/msg07714.htmlReported-by:
Michael Sartain <mikesart@fastmail.com> Reported-by:
Mathias Krause <minipli@googlemail.com> Signed-off-by:
Tony Jones <tonyj@suse.de> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Fixes: f7d82350 ("tools/events: Add files to create libtraceevent.a") Link: http://lkml.kernel.org/r/20190228015532.8941-1-tonyj@suse.deSigned-off-by:
-
Carlos Maiolino authored
[ Upstream commit dce30ca9 ] guard_bio_eod() can truncate a segment in bio to allow it to do IO on odd last sectors of a device. It already checks if the IO starts past EOD, but it does not consider the possibility of an IO request starting within device boundaries can contain more than one segment past EOD. In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will underflow bvec->bv_len. Fix this by checking if truncated_bytes is lower than PAGE_SIZE. This situation has been found on filesystems such as isofs and vfat, which doesn't check the device size before mount, if the device is smaller than the filesystem itself, a readahead on such filesystem, which spans EOD, can trigger this situation, leading a call to zero_user() with a wrong size possibly corrupting memory. I didn't see any crash, or didn't let the system run long enough to check if memory corruption will be hit somewhere, but adding instrumentation to guard_bio_end() to check truncated_bytes size, was enough to see the error. The following script can trigger the error. MNT=/mnt IMG=./DISK.img DEV=/dev/loop0 mkfs.vfat $IMG mount $IMG $MNT cp -R /etc $MNT &> /dev/null umount $MNT losetup -D losetup --find --show --sizelimit 16247280 $IMG mount $DEV $MNT find $MNT -type f -exec cat {} + >/dev/null Kudos to Eric Sandeen for coming up with the reproducer above Reviewed-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
luojiajun authored
[ Upstream commit 6e876c3d ] In jbd2_journal_commit_transaction(), if we are in abort mode, we may flush the buffer without setting descriptor block checksum by goto start_journal_io. Then fs is mounted, jbd2_descriptor_block_csum_verify() failed. [ 271.379811] EXT4-fs (vdd): shut down requested (2) [ 271.381827] Aborting journal on device vdd-8. [ 271.597136] JBD2: Invalid checksum recovering block 22199 in log [ 271.598023] JBD2: recovery failed [ 271.598484] EXT4-fs (vdd): error loading journal Fix this problem by keep setting descriptor block checksum if the descriptor buffer is not NULL. This checksum problem can be reproduced by xfstests generic/388. Signed-off-by:
luojiajun <luojiajun3@huawei.com> Signed-off-by:
-
Yao Liu authored
[ Upstream commit 68e2672f ] There is a NULL pointer dereference of devname in strspn() The oops looks something like: CIFS: Attempting to mount (null) BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 ... RIP: 0010:strspn+0x0/0x50 ... Call Trace: ? cifs_parse_mount_options+0x222/0x1710 [cifs] ? cifs_get_volume_info+0x2f/0x80 [cifs] cifs_setup_volume_info+0x20/0x190 [cifs] cifs_get_volume_info+0x50/0x80 [cifs] cifs_smb3_do_mount+0x59/0x630 [cifs] ? ida_alloc_range+0x34b/0x3d0 cifs_do_mount+0x11/0x20 [cifs] mount_fs+0x52/0x170 vfs_kern_mount+0x6b/0x170 do_mount+0x216/0xdc0 ksys_mount+0x83/0xd0 __x64_sys_mount+0x25/0x30 do_syscall_64+0x65/0x220 entry_SYSCALL_64_after_hwframe+0x49/0xbe Fix this by adding a NULL check on devname in cifs_parse_devname() Signed-off-by:
Yao Liu <yotta.liu@ucloud.cn> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Jason Cai (Xiang Feng) authored
[ Upstream commit 70de2cbd ] Invoking dm_get_device() twice on the same device path with different modes is dangerous. Because in that case, upgrade_mode() will alloc a new 'dm_dev' and free the old one, which may be referenced by a previous caller. Dereferencing the dangling pointer will trigger kernel NULL pointer dereference. The following two cases can reproduce this issue. Actually, they are invalid setups that must be disallowed, e.g.: 1. Creating a thin-pool with read_only mode, and the same device as both metadata and data. dmsetup create thinp --table \ "0 41943040 thin-pool /dev/vdb /dev/vdb 128 0 1 read_only" BUG: unable to handle kernel NULL pointer dereference at 0000000000000080 ... Call Trace: new_read+0xfb/0x110 [dm_bufio] dm_bm_read_lock+0x43/0x190 [dm_persistent_data] ? kmem_cache_alloc_trace+0x15c/0x1e0 __create_persistent_data_objects+0x65/0x3e0 [dm_thin_pool] dm_pool_metadata_open+0x8c/0xf0 [dm_thin_pool] pool_ctr.cold.79+0x213/0x913 [dm_thin_pool] ? realloc_argv+0x50/0x70 [dm_mod] dm_table_add_target+0x14e/0x330 [dm_mod] table_load+0x122/0x2e0 [dm_mod] ? dev_status+0x40/0x40 [dm_mod] ctl_ioctl+0x1aa/0x3e0 [dm_mod] dm_ctl_ioctl+0xa/0x10 [dm_mod] do_vfs_ioctl+0xa2/0x600 ? handle_mm_fault+0xda/0x200 ? __do_page_fault+0x26c/0x4f0 ksys_ioctl+0x60/0x90 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x55/0x150 entry_SYSCALL_64_after_hwframe+0x44/0xa9 2. Creating a external snapshot using the same thin-pool device. dmsetup create thinp --table \ "0 41943040 thin-pool /dev/vdc /dev/vdb 128 0 2 ignore_discard" dmsetup message /dev/mapper/thinp 0 "create_thin 0" dmsetup create snap --table \ "0 204800 thin /dev/mapper/thinp 0 /dev/mapper/thinp" BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 ... Call Trace: ? __alloc_pages_nodemask+0x13c/0x2e0 retrieve_status+0xa5/0x1f0 [dm_mod] ? dm_get_live_or_inactive_table.isra.7+0x20/0x20 [dm_mod] table_status+0x61/0xa0 [dm_mod] ctl_ioctl+0x1aa/0x3e0 [dm_mod] dm_ctl_ioctl+0xa/0x10 [dm_mod] do_vfs_ioctl+0xa2/0x600 ksys_ioctl+0x60/0x90 ? ksys_write+0x4f/0xb0 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x55/0x150 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by:
Jason Cai (Xiang Feng) <jason.cai@linux.alibaba.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Louis Taylor authored
[ Upstream commit 259594be ] When compiling with -Wformat, clang emits the following warnings: fs/cifs/smb1ops.c:312:20: warning: format specifies type 'unsigned short' but the argument has type 'unsigned int' [-Wformat] tgt_total_cnt, total_in_tgt); ^~~~~~~~~~~~ fs/cifs/cifs_dfs_ref.c:289:4: warning: format specifies type 'short' but the argument has type 'int' [-Wformat] ref->flags, ref->server_type); ^~~~~~~~~~ fs/cifs/cifs_dfs_ref.c:289:16: warning: format specifies type 'short' but the argument has type 'int' [-Wformat] ref->flags, ref->server_type); ^~~~~~~~~~~~~~~~ fs/cifs/cifs_dfs_ref.c:291:4: warning: format specifies type 'short' but the argument has type 'int' [-Wformat] ref->ref_flag, ref->path_consumed); ^~~~~~~~~~~~~ fs/cifs/cifs_dfs_ref.c:291:19: warning: format specifies type 'short' but the argument has type 'int' [-Wformat] ref->ref_flag, ref->path_consumed); ^~~~~~~~~~~~~~~~~~ The types of these arguments are unconditionally defined, so this patch updates the format character to the correct ones for ints and unsigned ints. Link: https://github.com/ClangBuiltLinux/linux/issues/378Signed-off-by:
Louis Taylor <louis@kragniz.eu> Signed-off-by:
-
Qian Cai authored
[ Upstream commit 4117992d ] KASAN does not play well with the page poisoning (CONFIG_PAGE_POISONING). It triggers false positives in the allocation path: BUG: KASAN: use-after-free in memchr_inv+0x2ea/0x330 Read of size 8 at addr ffff88881f800000 by task swapper/0 CPU: 0 PID: 0 Comm: swapper Not tainted 5.0.0-rc1+ #54 Call Trace: dump_stack+0xe0/0x19a print_address_description.cold.2+0x9/0x28b kasan_report.cold.3+0x7a/0xb5 __asan_report_load8_noabort+0x19/0x20 memchr_inv+0x2ea/0x330 kernel_poison_pages+0x103/0x3d5 get_page_from_freelist+0x15e7/0x4d90 because KASAN has not yet unpoisoned the shadow page for allocation before it checks memchr_inv() but only found a stale poison pattern. Also, false positives in free path, BUG: KASAN: slab-out-of-bounds in kernel_poison_pages+0x29e/0x3d5 Write of size 4096 at addr ffff8888112cc000 by task swapper/0/1 CPU: 5 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1+ #55 Call Trace: dump_stack+0xe0/0x19a print_address_description.cold.2+0x9/0x28b kasan_report.cold.3+0x7a/0xb5 check_memory_region+0x22d/0x250 memset+0x28/0x40 kernel_poison_pages+0x29e/0x3d5 __free_pages_ok+0x75f/0x13e0 due to KASAN adds poisoned redzones around slab objects, but the page poisoning needs to poison the whole page. Link: http://lkml.kernel.org/r/20190114233405.67843-1-cai@lca.pwSigned-off-by:
Qian Cai <cai@lca.pw> Acked-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
