Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.

This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config().  This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.

Note that ground and 100% vrefs are excluded from the list for
simplicity, currently.  We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since we have many bit flags in hda_gen_spec, rearrange in sections
and give more comments there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag.  It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... to be referred by the codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... and a little bit of code refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This gives us some additional safety.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Obvious copy-paste error.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Sometimes (or rather often) BIOS sets the pin default configurations
obviously wrongly.  Looking through these failures, one common pattern
is to enable some dead pins that are usually marked as speaker pins.
In such a case, we can skip them if the pins don't have the output
capability.

In this patch, add a check for the valid pin cap bit for each parsed
pin, and filter out when it's invalid.

The fix was originally suggested by Raymond Yau.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a hook for the capture mixer switch.  This will be used by IDT
codecs for controlling the mic-mute LED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

CA0110 codec is a fairly straightforward hardware implementation,
and we can use the generic parser almost as is.
Just set spec->multi_cap_vol flag to follow the current behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Replace the old parser code for C-Media auto-parser with the latest
generic parser.  For compatibility reason, the static bindings are
still left, but they could be cleaned up in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Through the hints via sysfs or patch, user can set specific behavior
flags for the generic parser now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It'll be used in hda_generic.c, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The pincfgs, init_verbs and hints set by sysfs or patch might be
changed dynamically on the fly, thus we need to protect it.
Add a simple protection via a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As David Henningsson recently suggested, some HP laptops use an unused
mic pin for controlling a mute LED, and this information is provided
via DMI string "HP_Mute_LED_X_Y" string.  This patch adds the generic
support for such cases, as we've already done in patch_sigmatel.c.
This is applied generically to all devices with ID 0x103c.

But as we don't know whether the device 103c:1586 really contains
HP_Mute_LED_X_Y DMI string, still keep the static setup for this
device using the mic2 pin 0x19.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some fixups such as setting the flags influencing on the parser
behavior should be applied before actually parsing the tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Try to recover from the regression: set the HP amp for the speaker and
add the hp jack mode enum as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode".  This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a new fixup type, HDA_FIXUP_PINCTLS, for overriding the pinctl
values of the given pins.  It takes the same array of struct pintbl
like HDA_FIXUP_PINS, but each entry contains the pinctl value instead
of the pin default config value.

This patch also replaces the corresponding codes in patch_realtek.c.
Without this change, the direct call of verbs may be overridden again
by the later call of pinctl restoration by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... instead of reading the value from the codec at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now the whole codebase has been changed from the earlier kernels, it
makes little sense to keep these aliases.  Simply replace with the
official names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching.  Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Use the new pin target accessors for managing the current pinctl
values in the generic parser.  The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target().  This will be referred again in the
codec init or resume phase to set the actual pinctl.

This value is kept while the auto-mute.  When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value.  Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Check more strictly about the validity of pinctl values in
snd_hda_set_pin_ctl() and correct the wrong bits automatically.
Also provide the helper function to correct pinctl bits to codec
drivers.

This automatically fixes the invalid pinctl writes that are found in
a few Realtek fixups for NID 0x0f amp like ASUS A6Rp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We already have the list of whole pin widgets and there is an unused
space in the list; let's use it for caching the current pinctl value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is.  Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since some codecs can choose the aamix as a capture source, we should
support it as well.  When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].

This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>