- 22 Jan, 2016 31 commits
-
-
Alan Stern authored
commit e50293ef upstream. Commit 8520f380 ("USB: change hub initialization sleeps to delayed_work") changed the hub_activate() routine to make part of it run in a workqueue. However, the commit failed to take a reference to the usb_hub structure or to lock the hub interface while doing so. As a result, if a hub is plugged in and quickly unplugged before the work routine can run, the routine will try to access memory that has been deallocated. Or, if the hub is unplugged while the routine is running, the memory may be deallocated while it is in active use. This patch fixes the problem by taking a reference to the usb_hub at the start of hub_activate() and releasing it at the end (when the work is finished), and by locking the hub interface while the work routine is running. It also adds a check at the start of the routine to see if the hub has already been disconnected, in which nothing should be done. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Alexandru Cornea <alexandru.cornea@intel.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: add prototype for hub_release() before first use] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Dan Carpenter authored
commit abdc9a3b upstream. The code expects the loop to end with "retries" set to zero but, because it is a post-op, it will end set to -1. I have fixed this by moving the decrement inside the loop. Fixes: 014aa2a3 ('USB: ipaq: minor ipaq_open() cleanup.') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 408fb0e5 upstream. commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way") teaches us that dealing with MSI-X can be troublesome. Further checks in the MSI-X architecture shows that if the PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we may not be able to access the BAR (since they are memory regions). Since the MSI-X tables are located in there.. that can lead to us causing PCIe errors. Inhibit us performing any operation on the MSI-X unless the MEMORY bit is set. Note that Xen hypervisor with: "x86/MSI-X: access MSI-X table only after having enabled MSI-X" will return: xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3! When the generic MSI code tries to setup the PIRQ without MEMORY bit set. Which means with later versions of Xen (4.6) this patch is not neccessary. This is part of XSA-157 Reviewed-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 7cfb905b upstream. Otherwise just continue on, returning the same values as previously (return of 0, and op->result has the PIRQ value). This does not change the behavior of XEN_PCI_OP_disable_msi[|x]. The pci_disable_msi or pci_disable_msix have the checks for msi_enabled or msix_enabled so they will error out immediately. However the guest can still call these operations and cause us to disable the 'ack_intr'. That means the backend IRQ handler for the legacy interrupt will not respond to interrupts anymore. This will lead to (if the device is causing an interrupt storm) for the Linux generic code to disable the interrupt line. Naturally this will only happen if the device in question is plugged in on the motherboard on shared level interrupt GSI. This is part of XSA-157 Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit a396f3a2 upstream. Otherwise an guest can subvert the generic MSI code to trigger an BUG_ON condition during MSI interrupt freeing: for (i = 0; i < entry->nvec_used; i++) BUG_ON(irq_has_action(entry->irq + i)); Xen PCI backed installs an IRQ handler (request_irq) for the dev->irq whenever the guest writes PCI_COMMAND_MEMORY (or PCI_COMMAND_IO) to the PCI_COMMAND register. This is done in case the device has legacy interrupts the GSI line is shared by the backend devices. To subvert the backend the guest needs to make the backend to change the dev->irq from the GSI to the MSI interrupt line, make the backend allocate an interrupt handler, and then command the backend to free the MSI interrupt and hit the BUG_ON. Since the backend only calls 'request_irq' when the guest writes to the PCI_COMMAND register the guest needs to call XEN_PCI_OP_enable_msi before any other operation. This will cause the generic MSI code to setup an MSI entry and populate dev->irq with the new PIRQ value. Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY and cause the backend to setup an IRQ handler for dev->irq (which instead of the GSI value has the MSI pirq). See 'xen_pcibk_control_isr'. Then the guest disables the MSI: XEN_PCI_OP_disable_msi which ends up triggering the BUG_ON condition in 'free_msi_irqs' as there is an IRQ handler for the entry->irq (dev->irq). Note that this cannot be done using MSI-X as the generic code does not over-write dev->irq with the MSI-X PIRQ values. The patch inhibits setting up the IRQ handler if MSI or MSI-X (for symmetry reasons) code had been called successfully. P.S. Xen PCIBack when it sets up the device for the guest consumption ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device). XSA-120 addendum patch removed that - however when upstreaming said addendum we found that it caused issues with qemu upstream. That has now been fixed in qemu upstream. This is part of XSA-157 Reviewed-by:
-
Konrad Rzeszutek Wilk authored
commit 5e0ce145 upstream. The guest sequence of: a) XEN_PCI_OP_enable_msix b) XEN_PCI_OP_enable_msix results in hitting an NULL pointer due to using freed pointers. The device passed in the guest MUST have MSI-X capability. The a) constructs and SysFS representation of MSI and MSI groups. The b) adds a second set of them but adding in to SysFS fails (duplicate entry). 'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that in a) pdev->msi_irq_groups is still set) and also free's ALL of the MSI-X entries of the device (the ones allocated in step a) and b)). The unwind code: 'free_msi_irqs' deletes all the entries and tries to delete the pdev->msi_irq_groups (which hasn't been set to NULL). However the pointers in the SysFS are already freed and we hit an NULL pointer further on when 'strlen' is attempted on a freed pointer. The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard against that. The check for msi_enabled is not stricly neccessary. This is part of XSA-157 Reviewed-by:
-
Konrad Rzeszutek Wilk authored
commit 56441f3c upstream. The guest sequence of: a) XEN_PCI_OP_enable_msi b) XEN_PCI_OP_enable_msi c) XEN_PCI_OP_disable_msi results in hitting an BUG_ON condition in the msi.c code. The MSI code uses an dev->msi_list to which it adds MSI entries. Under the above conditions an BUG_ON() can be hit. The device passed in the guest MUST have MSI capability. The a) adds the entry to the dev->msi_list and sets msi_enabled. The b) adds a second entry but adding in to SysFS fails (duplicate entry) and deletes all of the entries from msi_list and returns (with msi_enabled is still set). c) pci_disable_msi passes the msi_enabled checks and hits: BUG_ON(list_empty(dev_to_msi_list(&dev->dev))); and blows up. The patch adds a simple check in the XEN_PCI_OP_enable_msi to guard against that. The check for msix_enabled is not stricly neccessary. This is part of XSA-157. Reviewed-by:
-
Konrad Rzeszutek Wilk authored
commit 8135cf8b upstream. Double fetch vulnerabilities that happen when a variable is fetched twice from shared memory but a security check is only performed the first time. The xen_pcibk_do_op function performs a switch statements on the op->cmd value which is stored in shared memory. Interestingly this can result in a double fetch vulnerability depending on the performed compiler optimization. This patch fixes it by saving the xen_pci_op command before processing it. We also use 'barrier' to make sure that the compiler does not perform any optimization. This is part of XSA155. Reviewed-by:
-
Roger Pau Monné authored
commit 1f13d75c upstream. A compiler may load a switch statement value multiple times, which could be bad when the value is in memory shared with the frontend. When converting a non-native request to a native one, ensure that src->operation is only loaded once by using READ_ONCE(). This is part of XSA155. Signed-off-by:
Roger Pau Monné <roger.pau@citrix.com> Signed-off-by:
-
David Vrabel authored
commit 68a33bfd upstream. Instead of open-coding memcpy()s and directly accessing Tx and Rx requests, use the new RING_COPY_REQUEST() that ensures the local copy is correct. This is more than is strictly necessary for guest Rx requests since only the id and gref fields are used and it is harmless if the frontend modifies these. This is part of XSA155. Reviewed-by:
Wei Liu <wei.liu2@citrix.com> Signed-off-by:
-
David Vrabel authored
commit 0f589967 upstream. The last from guest transmitted request gives no indication about the minimum amount of credit that the guest might need to send a packet since the last packet might have been a small one. Instead allow for the worst case 128 KiB packet. This is part of XSA155. CC: stable@vger.kernel.org Reviewed-by:
-
David Vrabel authored
commit 454d5d88 upstream. Using RING_GET_REQUEST() on a shared ring is easy to use incorrectly (i.e., by not considering that the other end may alter the data in the shared ring while it is being inspected). Safe usage of a request generally requires taking a local copy. Provide a RING_COPY_REQUEST() macro to use instead of RING_GET_REQUEST() and an open-coded memcpy(). This takes care of ensuring that the copy is done correctly regardless of any possible compiler optimizations. Use a volatile source to prevent the compiler from reordering or omitting the copy. This is part of XSA155. Signed-off-by:
-
Michael Holzheu authored
commit 272fa59c upstream. The print_insn() function returns strings like "lghi %r1,0". To escape the '%' character in sprintf() a second '%' is used. For example "lghi %%r1,0" is converted into "lghi %r1,0". After print_insn() the output string is passed to printk(). Because format specifiers like "%r" or "%f" are ignored by printk() this works by chance most of the time. But for instructions with control registers like "lctl %c6,%c6,780" this fails because printk() interprets "%c" as character format specifier. Fix this problem and escape the '%' characters twice. For example "lctl %%%%c6,%%%%c6,780" is then converted by sprintf() into "lctl %%c6,%%c6,780" and by printk() into "lctl %c6,%c6,780". Signed-off-by:
Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> [bwh: Backported to 3.2: drop the OPERAND_VR case] Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit a50bd439 upstream. Russell King found that he had weird side effects when compiling the kernel with hard linked ccache. The reason was that recordmcount modified the kernel in place via mmap, and when a file gets modified twice by recordmcount, it will complain about it. To fix this issue, Russell wrote a patch that checked if the file was hard linked more than once and would unlink it if it was. Linus Torvalds was not happy with the fact that recordmcount does this in place modification. Instead of doing the unlink only if the file has two or more hard links, it does the unlink all the time. In otherwords, it always does a copy if it changed something. That is, it does the write out if a change was made. Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Hannes Frederic Sowa authored
commit 7bbadd2d upstream. Docbook does not like the definition of macros inside a field declaration and adds a warning. Move the definition out. Fixes: 79462ad0 ("net: add validation for the socket syscall protocol argument") Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: keep open-coding U8_MAX] Signed-off-by:
-
Russell King authored
commit dd39a265 upstream. recordmcount edits the file in-place, which can cause problems when using ccache in hardlink mode. Arrange for recordmcount to break a hardlinked object. Link: http://lkml.kernel.org/r/E1a7MVT-0000et-62@rmk-PC.arm.linux.org.ukSigned-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Johan Hovold authored
commit 157f38f9 upstream. Fix parent-device reference leak due to SPI-core taking an unnecessary reference to the parent when allocating the master structure, a reference that was never released. Note that driver core takes its own reference to the parent when the master device is registered. Fixes: 49dce689 ("spi doesn't need class_device") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Tilman Schmidt authored
commit 4c5e354a upstream. When shutting down the device, the struct ser_cardstate must not be kfree()d immediately after the call to platform_device_unregister() since the embedded struct platform_device is still in use. Move the kfree() call to the release method instead. Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Fixes: 2869b23e ("drivers/isdn/gigaset: new M101 driver (v2)") Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
-
Dan Carpenter authored
commit 40d24c4d upstream. There are two issue here. 1) cnt starts as maxloop + 1 so all these loops iterate one more time than intended. 2) At the end of the loop we test for "if (maxloop && !cnt)" but for the first two loops, we end with cnt equal to -1. Changing this to a pre-op means we end with cnt set to 0. Fixes: cae86d4a ('mISDN: Add driver for Infineon ISDN chipset family') Signed-off-by:
-
Sergei Shtylyov authored
commit 3e230993 upstream. For the little-endian SH771x kernels the driver has to byte-swap the RX/TX buffers, however yet unset physcial address from the TX descriptor is used to call sh_eth_soft_swap(). Use 'skb->data' instead... Fixes: 31fcb99d ("net: sh_eth: remove __flush_purge_region") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Anssi Hannula authored
commit 42e3121d upstream. AudioQuest DragonFly DAC reports a volume control range of 0..50 (0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which is obviously incorrect and would cause software using the dB information in e.g. volume sliders to have a massive volume difference in 100..102% range. Commit 2d1cb7f6 ("ALSA: usb-audio: add dB range mapping for some devices") added a dB range mapping for it with range 0..50 dB. However, the actual volume mapping seems to be neither linear volume nor linear dB scale, but instead quite close to the cubic mapping e.g. alsamixer uses, with a range of approx. -53...0 dB. Replace the previous quirk with a custom dB mapping based on some basic output measurements, using a 10-item range TLV (which will still fit in alsa-lib MAX_TLV_RANGE_SIZE). Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the range is 0..50, so if this gets fixed/changed in later HW revisions it will no longer be applied. v2: incorporated Takashi Iwai's suggestion for the quirk application method Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.2: open-code usb_audio_info()] Signed-off-by:
-
Clemens Ladisch authored
commit bf1d1c9b upstream. Add a DECLARE_TLV_DB_RANGE() macro so that dB range information can be specified without having to count the items manually for TLV_DB_RANGE_HEAD(). Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Clemens Ladisch authored
commit b5b9eb54 upstream. Add helper macros with a little bit of preprocessor magic to automatically compute the length of a TLV item. This lets us avoid having to compute this by hand, and will allow to use items that do not use a fixed length. Signed-off-by:
-
Peter Hurley authored
commit 9ce119f3 upstream. A line discipline which does not define a receive_buf() method can can cause a GPF if data is ever received [1]. Oddly, this was known to the author of n_tracesink in 2011, but never fixed. [1] GPF report BUG: unable to handle kernel NULL pointer dereference at (null) IP: [< (null)>] (null) PGD 3752d067 PUD 37a7b067 PMD 0 Oops: 0010 [#1] SMP KASAN Modules linked in: CPU: 2 PID: 148 Comm: kworker/u10:2 Not tainted 4.4.0-rc2+ #51 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: events_unbound flush_to_ldisc task: ffff88006da94440 ti: ffff88006db60000 task.ti: ffff88006db60000 RIP: 0010:[<0000000000000000>] [< (null)>] (null) RSP: 0018:ffff88006db67b50 EFLAGS: 00010246 RAX: 0000000000000102 RBX: ffff88003ab32f88 RCX: 0000000000000102 RDX: 0000000000000000 RSI: ffff88003ab330a6 RDI: ffff88003aabd388 RBP: ffff88006db67c48 R08: ffff88003ab32f9c R09: ffff88003ab31fb0 R10: ffff88003ab32fa8 R11: 0000000000000000 R12: dffffc0000000000 R13: ffff88006db67c20 R14: ffffffff863df820 R15: ffff88003ab31fb8 FS: 0000000000000000(0000) GS:ffff88006dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000000 CR3: 0000000037938000 CR4: 00000000000006e0 Stack: ffffffff829f46f1 ffff88006da94bf8 ffff88006da94bf8 0000000000000000 ffff88003ab31fb0 ffff88003aabd438 ffff88003ab31ff8 ffff88006430fd90 ffff88003ab32f9c ffffed0007557a87 1ffff1000db6cf78 ffff88003ab32078 Call Trace: [<ffffffff8127cf91>] process_one_work+0x8f1/0x17a0 kernel/workqueue.c:2030 [<ffffffff8127df14>] worker_thread+0xd4/0x1180 kernel/workqueue.c:2162 [<ffffffff8128faaf>] kthread+0x1cf/0x270 drivers/block/aoe/aoecmd.c:1302 [<ffffffff852a7c2f>] ret_from_fork+0x3f/0x70 arch/x86/entry/entry_64.S:468 Code: Bad RIP value. RIP [< (null)>] (null) RSP <ffff88006db67b50> CR2: 0000000000000000 ---[ end trace a587f8947e54d6ea ]--- Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
James Bottomley authored
commit 5e103356 upstream. KASAN found that our additional element processing scripts drop off the end of the VPD page into unallocated space. The reason is that not every element has additional information but our traversal routines think they do, leading to them expecting far more additional information than is present. Fix this by adding a gate to the traversal routine so that it only processes elements that are expected to have additional information (list is in SES-2 section 6.1.13.1: Additional Element Status diagnostic page overview) Reported-by:
Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
-
James Bottomley authored
commit 3417c1b5 upstream. Simple enclosure implementations (mostly USB) are allowed to return only page 8 to every diagnostic query. That really confuses our implementation because we assume the return is the page we asked for and end up doing incorrect offsets based on bogus information leading to accesses outside of allocated ranges. Fix that by checking the page code of the return and giving an error if it isn't the one we asked for. This should fix reported bugs with USB storage by simply refusing to attach to enclosures that behave like this. It's also good defensive practise now that we're starting to see more USB enclosures. Reported-by:
Andrea Gelmini <andrea.gelmini@gelma.net> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Johannes Berg authored
commit b7bb1100 upstream. Some users of rfkill, like NFC and cfg80211, use a dynamic name when allocating rfkill, in those cases dev_name(). Therefore, the pointer passed to rfkill_alloc() might not be valid forever, I specifically found the case that the rfkill name was quite obviously an invalid pointer (or at least garbage) when the wiphy had been renamed. Fix this by making a copy of the rfkill name in rfkill_alloc(). Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Jason A. Donenfeld authored
commit 70d906bc upstream. Some ciphers actually support encrypting zero length plaintexts. For example, many AEAD modes support this. The resulting ciphertext for those winds up being only the authentication tag, which is a result of the key, the iv, the additional data, and the fact that the plaintext had zero length. The blkcipher constructors won't copy the IV to the right place, however, when using a zero length input, resulting in some significant problems when ciphers call their initialization routines, only to find that the ->iv parameter is uninitialized. One such example of this would be using chacha20poly1305 with a zero length input, which then calls chacha20, which calls the key setup routine, which eventually OOPSes due to the uninitialized ->iv member. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Wang Dongsheng authored
commit acfc1cc1 upstream. If diu_ops is not implemented on platform, kernel will access a NULL pointer. We need to check this pointer in DIU initialization. Signed-off-by:
Wang Dongsheng <dongsheng.wang@freescale.com> Acked-by:
Timur Tabi <timur@tabi.org> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Eric Dumazet authored
commit 69ce6487 upstream. While cooking the sctp np->opt rcu fixes, I forgot to move one rcu_read_unlock() after the added rcu_dereference() in sctp_v6_get_dst() This gave lockdep warnings reported by Dave Jones. Fixes: c836a8ba ("ipv6: sctp: add rcu protection around np->opt") Reported-by:
Dave Jones <davej@codemonkey.org.uk> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
lucien authored
commit 8a0d19c5 upstream. when A sends a data to B, then A close() and enter into SHUTDOWN_PENDING state, if B neither claim his rwnd is 0 nor send SACK for this data, A will keep retransmitting this data until t5 timeout, Max.Retrans times can't work anymore, which is bad. if B's rwnd is not 0, it should send abort after Max.Retrans times, only when B's rwnd == 0 and A's retransmitting beyonds Max.Retrans times, A will start t5 timer, which is also commit f8d96052 ("sctp: Enforce retransmission limit during shutdown") means, but it lacks the condition peer rwnd == 0. so fix it by adding a bit (zero_window_announced) in peer to record if the last rwnd is 0. If it was, zero_window_announced will be set. and use this bit to decide if start t5 timer when local.state is SHUTDOWN_PENDING. Fixes: commit f8d96052 ("sctp: Enforce retransmission limit during shutdown") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
- 30 Dec, 2015 9 commits
-
-
Ben Hutchings authored
-
Ben Hutchings authored
commit 4ab42d78 upstream. Currently slhc_init() treats out-of-range values of rslots and tslots as equivalent to 0, except that if tslots is too large it will dereference a null pointer (CVE-2015-7799). Add a range-check at the top of the function and make it return an ERR_PTR() on error instead of NULL. Change the callers accordingly. Compile-tested only. Reported-by:
郭永刚 <guoyonggang@360.cn> References: http://article.gmane.org/gmane.comp.security.oss.general/17908Signed-off-by:
-
Ben Hutchings authored
commit 0baa57d8 upstream. Compile-tested only. Signed-off-by:
-
Eric Dumazet authored
commit 60bc851a upstream. Using bit fields is dangerous on ppc64/sparc64, as the compiler [1] uses 64bit instructions to manipulate them. If the 64bit word includes any atomic_t or spinlock_t, we can lose critical concurrent changes. This is happening in af_unix, where unix_sk(sk)->gc_candidate/ gc_maybe_cycle/lock share the same 64bit word. This leads to fatal deadlock, as one/several cpus spin forever on a spinlock that will never be available again. A safer way would be to use a long to store flags. This way we are sure compiler/arch wont do bad things. As we own unix_gc_lock spinlock when clearing or setting bits, we can use the non atomic __set_bit()/__clear_bit(). recursion_level can share the same 64bit location with the spinlock, as it is set only with this spinlock held. [1] bug fixed in gcc-4.8.0 : http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52080Reported-by:
Ambrose Feinstein <ambrose@google.com> Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit 3822b5c2 ] With b3ca9b02, the AF_UNIX SOCK_STREAM receive code was changed from using mutex_lock(&u->readlock) to mutex_lock_interruptible(&u->readlock) to prevent signals from being delayed for an indefinite time if a thread sleeping on the mutex happened to be selected for handling the signal. But this was never a problem with the stream receive code (as opposed to its datagram counterpart) as that never went to sleep waiting for new messages with the mutex held and thus, wouldn't cause secondary readers to block on the mutex waiting for the sleeping primary reader. As the interruptible locking makes the code more complicated in exchange for no benefit, change it back to using mutex_lock. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Acked-by:
-
David S. Miller authored
[ Upstream commit 5233252f ] Signed-off-by:
-
WANG Cong authored
[ Upstream commit 09ccfd23 ] Reported-by:
Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Sergei Shtylyov authored
[ Upstream commit 248be83d ] In a low memory situation the following kernel oops occurs: Unable to handle kernel NULL pointer dereference at virtual address 00000050 pgd = 8490c000 [00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: CPU: 0 Not tainted (3.4-at16 #9) PC is at skb_put+0x10/0x98 LR is at sh_eth_poll+0x2c8/0xa10 pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113 sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4 r10: 0000003f r9 : 000005ea r8 : 00000000 r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180 r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c53c7d Table: 4248c059 DAC: 00000015 Process klogd (pid: 2046, stack limit = 0x84eb02e8) [...] This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left NULL but sh_eth_rx() later uses it without checking. Add such check... Reported-by:
Yasushi SHOJI <yashi@atmark-techno.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 79462ad0 ] 郭永刚 reported that one could simply crash the kernel as root by using a simple program: int socket_fd; struct sockaddr_in addr; addr.sin_port = 0; addr.sin_addr.s_addr = INADDR_ANY; addr.sin_family = 10; socket_fd = socket(10,3,0x40000000); connect(socket_fd , &addr,16); AF_INET, AF_INET6 sockets actually only support 8-bit protocol identifiers. inet_sock's skc_protocol field thus is sized accordingly, thus larger protocol identifiers simply cut off the higher bits and store a zero in the protocol fields. This could lead to e.g. NULL function pointer because as a result of the cut off inet_num is zero and we call down to inet_autobind, which is NULL for raw sockets. kernel: Call Trace: kernel: [<ffffffff816db90e>] ? inet_autobind+0x2e/0x70 kernel: [<ffffffff816db9a4>] inet_dgram_connect+0x54/0x80 kernel: [<ffffffff81645069>] SYSC_connect+0xd9/0x110 kernel: [<ffffffff810ac51b>] ? ptrace_notify+0x5b/0x80 kernel: [<ffffffff810236d8>] ? syscall_trace_enter_phase2+0x108/0x200 kernel: [<ffffffff81645e0e>] SyS_connect+0xe/0x10 kernel: [<ffffffff81779515>] tracesys_phase2+0x84/0x89 I found no particular commit which introduced this problem. CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by:
-
