Instead of adding and deleting the gadget device in the start and stop
invocations. Use device_register in the probe method to initialize
and add the gadget device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The number of get and put calls should always be equal.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Fixes possible section mismatch warnings.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Gadget drivers should be compilable on all architectures.
This patch removes one dependency on architecture-specific code.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds support for EHCI compliant HSUSB Host controller found
on Marvell Socs.

It fits both OTG and SPH controller on marvell Socs, including
PXA9xx/MMP2/MMP3/MGx.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This driver is for ChipIdea USB OTG controller on Marvell Socs.
PXA9xx/MMP2/MMP3/MGx all have this USB OTG controller.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch do the following things:
1. Change the Kconfig information.
2. Rename the driver name.
3. Don't do any type cast to io memory.
4. Add dummy stub for clk framework.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

According to ChipIdea's SPEC, we cannot touch curr_dtd_ptr in dqh
directly, use prime endpoint instead.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

For super speed bulk transfer, the max burst size
is 16, so that 4 bits of maxburst cannot store it.
Signed-off-by: Yu Xu <yuxu@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Rewrite function queue_dtd according to ChipIdea's reference manual.
Remove all unnecessary logic, it will enhance the performance.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

readl expected 'const volatile void *' as the argument.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Gcc complains about this printk:
drivers/usb/renesas_usbhs/mod_gadget.c:188:3: warning: format ‘%x’
	expects argument of type ‘unsigned int’, but argument 3 has type
	‘dma_addr_t’ [-Wformat]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch tidyup below smatch complaint

drivers/usb/renesas_usbhs/mod_host.c +642 usbhsh_queue_done()
	 warn: variable dereferenced before check 'urb' (see line 636)

Special thanks to Dan
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Packet should be force removed when reset/detach
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Without this patch, USB host hub shows error when cable was detached
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It is possible to judge whether renesas_usbhs driver is running,
by checking attch irq mask.
This patch adds usbhsh_is_running() to check it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

attch interrupt might happen infinitely on some USB hub (self power?).
This patch disable attch irq after device attached,
and enable it again when detach irq happen.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.

Then, each pipe should care own pipe sequence for next packet.
This patch adds sequence control.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.
This patch adds usbhsh_pipe_attach/detach() functions for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds usbhsh_endpoint_detach_all() for error case.
usbhs_endpoitn_xxx() functions were moved to upper side in source code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Current renesas_usbhs had been assigning udev to each urb.
It was executed even though it was device0.
For this reason, the device0 had to set the new device address
which has still not been assigned. (it will be assigned on next step).
Current renesas_usbhs used fixed address for it.
but it is not good for USB hub support.
This patch modifies this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usbhsh_ureq_free() is not enough when urb dequeued.

Without this patch, the driver can not recognize re-connected
USB device after USB hub disconnected
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

usbhsh_urb_enqueue() didn't have error value when
usbhsh_device_attach() failed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

replace some debug info, make it easy to use.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch impletments system suspend/resume functions for Marvell
otg controller.
If OTG is enabled, OTG driver will do most of the work.
If not, we will check clock gating.
  If clock gating is enabled, the UDC will be start/stop automatically.
  If not, UDC will be start/stop in suspend/resume functions.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Split the clock relative code from clock gating solution.
Then we can remove some duplicate code, make the code more clean.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When device is stopped, there is no need to handle ISR.
Especially when otg switch to HOST mode.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add otg relative code, make it possible to switch between host and
device.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.

The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Michal Nazarewicz <[4]mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

current renesas_usbhs is using new style udc_start/stop from
af1d7056
(usb: gadget: renesas: convert to new style).

with this patch we can finally remove the global "the_controller_link"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When poping packet from queue, it needs correct end procedure.
This patch call usbhsg_queue_pop() in usbhsg_pipe_disable().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Current renesas_usbhs driver always tries to send packet in end of recip handler.
But it breaks chapter 9 EndpointHalt test.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds basic get-status support for chapter 9 test.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds basic set-feature support for chapter 9 test.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This is preparation for chapter 9 test
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

recip handler will call various functions which are holding
usbhs_lock.

This patch removes superfluous usbhs_lock from recip handler
to escape double lock.

[ balbi@ti.com : brushed up commit log a bit ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This commit renames the “speed” field of the usb_gadget_driver
structure to “max_speed”.  This is so that to make it more
apparent that the field represents the maximum speed gadget
driver can support.

This also make the field look more like fields with the same
name in usb_gadget and usb_composite_driver structures.  All
of those represent the *maximal* speed given entity supports.

After this commit, there are the following fields in various
structures:
* usb_gadget::speed - the current connection speed,
* usb_gadget::max_speed - maximal speed UDC supports,
* usb_gadget_driver::max_speed - maximal speed gadget driver
  supports, and
* usb_composite_driver::max_speed - maximal speed composite
  gadget supports.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.

[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>