- 22 Jul, 2022 38 commits
-
-
Zijun Hu authored
Core driver addtionally checks LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken, so remove this unnecessary quirk for QCA controllers. The reason why these two HCI commands are broken for QCA controllers is that feature "Erroneous Data Reporting" is not enabled by their firmware as shown by below log: @ RAW Open: hcitool (privileged) version 2.22 < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 288 entries ...... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ...... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 Status: Success (0x00) Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87 3 slot packets ...... Signed-off-by:Zijun Hu <quic_zijuhu@quicinc.com> Tested-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
Zijun Hu authored
BT core driver should addtionally check LMP feature bit "Erroneous Data Reporting" instead of quirk HCI_QUIRK_BROKEN_ERR_DATA_REPORTING set by BT device driver to decide if HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting are broken. BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 2, Part C | page 587 This feature indicates whether the device is able to support the Packet_Status_Flag and the HCI commands HCI_Write_Default_- Erroneous_Data_Reporting and HCI_Read_Default_Erroneous_- Data_Reporting. the quirk was introduced by 'commit cde1a8a9 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")' to mark HCI commands HCI_Read|Write_Default_Erroneous_Data_Reporting broken by BT device driver, but the reason why these two HCI commands are broken is that feature "Erroneous Data Reporting" is not enabled by firmware, this scenario is illustrated by below log of QCA controllers with USB I/F: @ RAW Open: hcitool (privileged) version 2.22 < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) Commands: 288 entries ...... Read Default Erroneous Data Reporting (Octet 18 - Bit 2) Write Default Erroneous Data Reporting (Octet 18 - Bit 3) ...... < HCI Command: Read Default Erroneous Data Reporting (0x03|0x005a) plen 0 > HCI Event: Command Complete (0x0e) plen 4 Read Default Erroneous Data Reporting (0x03|0x005a) ncmd 1 Status: Unknown HCI Command (0x01) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 > HCI Event: Command Complete (0x0e) plen 12 Read Local Supported Features (0x04|0x0003) ncmd 1 Status: Success (0x00) Features: 0xff 0xfe 0x0f 0xfe 0xd8 0x3f 0x5b 0x87 3 slot packets ...... Signed-off-by:
-
Zijun Hu authored
Event HCI_Truncated_Page_Complete should belong to central and HCI_Peripheral_Page_Response_Timeout should belong to peripheral, but hci_set_event_mask_page_2_sync() take these two events for wrong roles, so correct it by this change. Signed-off-by:
-
He Wang authored
Add VID/PID 0489:e0e2 for MediaTek MT7922 Bluetooth chip. Found and tested with Asus UM5302TA. From /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0e2 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by:
He Wang <xw897002528@gmail.com> Signed-off-by:
-
Yuri D'Elia authored
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for MTK controllers since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN. Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576Signed-off-by:
Yuri D'Elia <wavexx@thregr.org> Signed-off-by:
-
Hakan Jansson authored
Add device specific data for max baudrate in autobaud mode. This allows the host to use a baudrate higher than "init speed" when loading FW in autobaud mode. The device specific max baudrate in autobaud mode for CYW55572 is set to 921600 bps. Devices without device specific max baudrate in autobaud mode will use init speed as before. If no device specific init speed has been specified, it will default to the bcm_proto default 115200 bps. The increased baud rate improves FW load time. The exact load time will depend on the specific system and FW being used. As a rough indication, the FW load time dropped from ~9s @ 115.2kbps to ~1.7s @ 921.6kbps in one test. Signed-off-by:
Hakan Jansson <hakan.jansson@infineon.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Hakan Jansson authored
Always prevent trying to set device baudrate before calling setup() when using autobaud mode. This was previously happening for devices which had device specific data with member no_early_set_baudrate set to 0. Signed-off-by:
-
Hakan Jansson authored
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon. Signed-off-by:
-
Hakan Jansson authored
Add conditional constraint to make property "reset-gpios" available only for compatible devices acually having the reset pin. Make property "brcm,requires-autobaud-mode" depend on property "shutdown-gpios" as the shutdown pin is required to enter autobaud mode. I looked at all compatible devices and compiled the matrix below before formulating the conditional constraint. This was a pure paper exercise and no verification testing has been performed. d e v h i o c s s e t h - - u w w v t r a a v d d e k k b d o s e e a i w e u u t o n t p p - - - - - - s s g g g g u u p p p p t p p i i i i x l p p o o o o c p l l s s s s o o y y --------------------------------------- brcm,bcm20702a1 X X X X X X X X brcm,bcm4329-bt X X X X X X X X brcm,bcm4330-bt X X X X X X X X brcm,bcm4334-bt X - X X X X X X brcm,bcm43438-bt X - X X X X X X brcm,bcm4345c5 X - X X X X X X brcm,bcm43540-bt X - X X X X X X brcm,bcm4335a0 X - X X X X X X brcm,bcm4349-bt X - X X X X X X infineon,cyw55572-bt X - X X X X X X Signed-off-by:Rob Herring <robh@kernel.org> Reviewed-by:
-
Hakan Jansson authored
CYW55572 is a Wi-Fi + Bluetooth combo device from Infineon. Extend the binding with its DT compatible. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
-
Dan Carpenter authored
The bt_skb_sendmsg() function can't return NULL so there is no need to check for that. Several of these checks were removed previously but this one was missed. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x13D3, 0x3586) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3586 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Hilda Wu <hildawu@realtek.com> Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x13D3, 0x3587) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3587 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x0CB8, 0xC558) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c558 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x04c5, 0x1675) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04c5 ProdID=1675 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Hilda Wu authored
Add the support ID(0x04CA, 0x4007) to usb_device_id table for Realtek RTL8852C. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=4007 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
-
Ying Hsu authored
Bluetooth HCI devices indicate if they are able to wakeup in the wakeup callback since 'commit 4539ca67 ("Bluetooth: Rename driver .prevent_wake to .wakeup")'. This patch adds a default wakeup callback for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are wakeable for backward compatibility. For those who need a customized behavior, one can override it before calling hci_uart_register_device(). Fixes: 4539ca67 ("Bluetooth: Rename driver .prevent_wake to .wakeup") Signed-off-by:
Ying Hsu <yinghsu@chromium.org> Reviewed-by:
Alain Michaud <alainm@chromium.org> Signed-off-by:
-
Luiz Augusto von Dentz authored
These devices are likely going to be reprogrammed when disconnected so this avoid a whole bunch of commands attempt to remove and the add back to the list. Signed-off-by:
Zhengping Jiang <jiangzp@google.com>
-
Luiz Augusto von Dentz authored
When programming a new entry into the resolving list it shall default to network mode since the params may contain the mode programmed when the device was last added to the resolving list. Link: https://bugzilla.kernel.org/show_bug.cgi?id=209745 Fixes: 853b70b5 ("Bluetooth: hci_sync: Set Privacy Mode when updating the resolving list") Signed-off-by:
-
Tamas Koczka authored
Annotate hci_rx_work() with kcov_remote_start() and kcov_remote_stop() calls, so remote KCOV coverage is collected while processing the rx_q queue which is the main incoming Bluetooth packet queue. Coverage is associated with the thread which created the packet skb. The collected extra coverage helps kernel fuzzing efforts in finding vulnerabilities. This change only has effect if the kernel is compiled with CONFIG_KCOV, otherwise kcov_ functions don't do anything. Signed-off-by:
Tamas Koczka <poprdi@google.com> Tested-by:
Aleksandr Nogikh <nogikh@google.com> Reviewed-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Zhengping Jiang authored
After resuming, remove setting scanning_paused to false, because it is checked and set to false in hci_resume_scan_sync. Also move setting the value to false before updating passive scan, because the value is used when resuming passive scan. Fixes: 3b420553 (Bluetooth: hci_sync: Fix attempting to suspend with unfiltered passive scan) Signed-off-by:
Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by:
-
Sean Wang authored
Commit ce64b3e9 ("Bluetooth: mt7921s: Support wake on bluetooth") adds the wake on bluethooth via a dedicated GPIO. Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup), when supported by the SDIO host driver. Co-developed-by:
Yake Yang <yake.yang@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by:
-
Zhengping Jiang authored
Set the connection data before calling get_conn_info_sync, so it can be verified the connection is still connected, before refreshing cached values. Fixes: 47db6b42 ("Bluetooth: hci_sync: Convert MGMT_OP_GET_CONN_INFO") Signed-off-by:
-
Luiz Augusto von Dentz authored
The scan response and advertising data needs to be tracked on a per instance (adv_info) since when these instaces are removed so are their data, to fix that new flags are introduced which is used to mark when the data changes and then checked to confirm when the data needs to be synced with the controller. Tested-by:
Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
Both dev_name and short_name are not guaranteed to be NULL terminated so this instead use strnlen and then attempt to determine if the resulting string needs to be truncated or not. Link: https://bugzilla.kernel.org/show_bug.cgi?id=216018Signed-off-by:
-
Xiaohui Zhang authored
Similar to the handling of l2cap_ecred_connect in commit d3715b23 ("Bluetooth: use memset avoid memory leaks"), we thought a patch might be needed here as well. Use memset to initialize structs to prevent memory leaks in l2cap_le_connect Signed-off-by:
Xiaohui Zhang <xiaohuizhang@ruc.edu.cn> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Dan Carpenter authored
Preserve the error code from hci_register_suspend_notifier(). Don't return success. Fixes: d6bb2a91f95b ("Bluetooth: Unregister suspend with userchannel") Signed-off-by: -
Ahmad Fatoum authored
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth portion can be controlled over serial. Two subversions are added for the chip, because ROM firmware reports 002.002.013 (at least for the chips I have here), while depending on patchram firmware revision, either 002.002.013 or 002.002.014 is reported. Signed-off-by:
Ahmad Fatoum <a.fatoum@pengutronix.de> Reviewed-by:
-
Ahmad Fatoum authored
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth portion can be controlled over serial. Extend the binding with its DT compatible. Acked-by:
-
Abhishek Pandit-Subedi authored
When HCI_USERCHANNEL is used, unregister the suspend notifier when binding and register when releasing. The userchannel socket should be left alone after open is completed. Signed-off-by:
-
Abhishek Pandit-Subedi authored
When a userchannel socket is released, we should check whether the hdev is already unregistered before sending out an IndexAdded. Signed-off-by:
-
Schspa Shi authored
The HCI command, event, and data packet processing workqueue is drained to avoid deadlock in commit 76727c02 ("Bluetooth: Call drain_workqueue() before resetting state"). There is another delayed work, which will queue command to this drained workqueue. Which results in the following error report: Bluetooth: hci2: command 0x040f tx timeout WARNING: CPU: 1 PID: 18374 at kernel/workqueue.c:1438 __queue_work+0xdad/0x1140 Workqueue: events hci_cmd_timeout RIP: 0010:__queue_work+0xdad/0x1140 RSP: 0000:ffffc90002cffc60 EFLAGS: 00010093 RAX: 0000000000000000 RBX: ffff8880b9d3ec00 RCX: 0000000000000000 RDX: ffff888024ba0000 RSI: ffffffff814e048d RDI: ffff8880b9d3ec08 RBP: 0000000000000008 R08: 0000000000000000 R09: 00000000b9d39700 R10: ffffffff814f73c6 R11: 0000000000000000 R12: ffff88807cce4c60 R13: 0000000000000000 R14: ffff8880796d8800 R15: ffff8880796d8800 FS: 0000000000000000(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000c0174b4000 CR3: 000000007cae9000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? queue_work_on+0xcb/0x110 ? lockdep_hardirqs_off+0x90/0xd0 queue_work_on+0xee/0x110 process_one_work+0x996/0x1610 ? pwq_dec_nr_in_flight+0x2a0/0x2a0 ? rwlock_bug.part.0+0x90/0x90 ? _raw_spin_lock_irq+0x41/0x50 worker_thread+0x665/0x1080 ? process_one_work+0x1610/0x1610 kthread+0x2e9/0x3a0 ? kthread_complete_and_exit+0x40/0x40 ret_from_fork+0x1f/0x30 </TASK> To fix this, we can add a new HCI_DRAIN_WQ flag, and don't queue the timeout workqueue while command workqueue is draining. Fixes: 76727c02 ("Bluetooth: Call drain_workqueue() before resetting state") Reported-by: syzbot+63bed493aebbf6872647@syzkaller.appspotmail.com Signed-off-by:
Schspa Shi <schspa@gmail.com> Signed-off-by:
-
Jiasheng Jiang authored
As platform_driver_register() could fail, it should be better to deal with the return value in order to maintain the code consisitency. Fixes: 1ab1f239 ("Bluetooth: hci_intel: Add support for platform driver") Signed-off-by:
Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by:
-
Alain Michaud authored
If a hardware error occurs and the connections are flushed without a disconnection_complete event being signaled, the temporary linkkeys are not flushed. This change ensures that any outstanding flushable linkkeys are flushed when the connection are flushed from the hash table. Additionally, this also makes use of test_and_clear_bit to avoid multiple attempts to delete the link key that's already been flushed. Signed-off-by:
-
Hakan Jansson authored
Use the presence of a DT property, "brcm,requires-autobaud-mode", to enable startup in autobaud mode. If the property is present, the device is started in autobaud mode by asserting RTS (BT_UART_CTS_N) prior to powering on the device. Also prevent the use of unsupported commands for devices started in autobaud mode. Only a limited subset of HCI commands are supported in autobaud mode. Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading. Autobaud mode can also be required on some boards where the controller device is using a non-standard baud rate in normal mode when first powered on. Signed-off-by:
-
Hakan Jansson authored
Add property, "brcm,requires-autobaud-mode", to enable autobaud mode selection. Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading. Autobaud mode can also be required on some boards where the controller device is using a non-standard baud rate when first powered on. Signed-off-by:
-
Sai Teja Aluvala authored
This fixes the return value of qca_wakeup(), since .wakeup work inversely with original .prevent_wake. Fixes: 4539ca67 (Bluetooth: Rename driver .prevent_wake to .wakeup) Signed-off-by:
Sai Teja Aluvala <quic_saluvala@quicinc.com> Signed-off-by:
-
Aaron Ma authored
It is 13d3:3568 for MediaTek MT7922 USB Bluetooth chip. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3568 Rev=01.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=... C: #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by:
Aaron Ma <aaron.ma@canonical.com> Signed-off-by:
-
- 21 Jul, 2022 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski authored
No conflicts. Signed-off-by:Jakub Kicinski <kuba@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from can. Still no major regressions, most of the changes are still due to data races fixes, plus the usual bunch of drivers fixes. Previous releases - regressions: - tcp/udp: make early_demux back namespacified. - dsa: fix issues with vlan_filtering_is_global Previous releases - always broken: - ip: fix data-races around ipv4_net_table (round 2, 3 & 4) - amt: fix validation and synchronization bugs - can: fix detection of mcp251863 - eth: iavf: fix handling of dummy receive descriptors - eth: lan966x: fix issues with MAC table - eth: stmmac: dwmac-mediatek: fix clock issue Misc: - dsa: update documentation" * tag 'net-5.19-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits) mlxsw: spectrum_router: Fix IPv4 nexthop gateway indication net/sched: cls_api: Fix flow action initialization tcp: Fix data-races around sysctl_tcp_max_reordering. tcp: Fix a data-race around sysctl_tcp_abort_on_overflow. tcp: Fix a data-race around sysctl_tcp_rfc1337. tcp: Fix a data-race around sysctl_tcp_stdurg. tcp: Fix a data-race around sysctl_tcp_retrans_collapse. tcp: Fix data-races around sysctl_tcp_slow_start_after_idle. tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts. tcp: Fix data-races around sysctl_tcp_recovery. tcp: Fix a data-race around sysctl_tcp_early_retrans. tcp: Fix data-races around sysctl knobs related to SYN option. udp: Fix a data-race around sysctl_udp_l3mdev_accept. ip: Fix data-races around sysctl_ip_prot_sock. ipv4: Fix data-races around sysctl_fib_multipath_hash_fields. ipv4: Fix data-races around sysctl_fib_multipath_hash_policy. ipv4: Fix a data-race around sysctl_fib_multipath_use_neigh. can: rcar_canfd: Add missing of_node_put() in rcar_canfd_probe() can: mcp251xfd: fix detection of mcp251863 Documentation: fix udp_wmem_min in ip-sysctl.rst ...
-
