The 6185 family of devices has only 256 address databases. Their 8-bit
FID for ATU and VTU operations are split into ATU Control and ATU/VTU
Operation registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marvell switch chips have different number of address databases.

The code currently only supports models with 4096 databases. Such switch
has dedicated FID registers for ATU and VTU operations. Models with
fewer databases have their FID split in several registers.

List them all but only support models with 4096 databases at the moment.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only switch families with 4096 address databases have dedicated FID
registers for ATU and VTU operations.

Factorize the access to the GLOBAL_ATU_FID register and introduce a
mv88e6xxx_has_fid_reg() helper function to protect the access to
GLOBAL_ATU_FID and GLOBAL_VTU_FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a mv88e6xxx_has_stu() helper to protect the access to the
GLOBAL_VTU_SID register, instead of checking switch families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the sh-irda driver as it appears to be unused since
c0bb9b30 ("ARCH: ARM: shmobile: Remove ag5evm board support").
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moritz Fischer says:

====================
macb: Codingstyle cleanups

resending almost unchanged v2 here:

Changes from v2:
* Rebased onto net-next
* Changed 5th patches commit message
* Added Nicholas' and Michal's Acked-Bys

Changes from v1:
* Backed out variable scope changes
* Separated out ether_addr_copy into it's own commit
* Fixed typo in comments as suggested by Joe
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checkpatch suggests using ether_addr_copy over memcpy
to copy the mac address.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit deals with a bunch of checkpatch suggestions
that without changing behavior make checkpatch happier.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit takes care of the coding style warnings
that are mostly due to a different comment style and
lines over 80 chars, as well as a dangling else.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

checkpatch.pl gave the following error:

ERROR: space required before the open parenthesis '('
+	for(; p < end; p++, offset += 4)
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch supports the following interrupts.

- One interrupt for multiple (timestamp, error, gPTP)
- One interrupt for emac
- Four interrupts for dma queue (best effort rx/tx, network control rx/tx)

This patch improve efficiency of the interrupt handler by adding the
interrupt handler corresponding to each interrupt source described
above. Additionally, it reduces the number of times of the access to
EthernetAVB IF.
Also this patch prevent this driver depends on the whim of a boot loader.

[ykaneko0929@gmail.com: define bit names of registers]
[ykaneko0929@gmail.com: add comment for gen3 only registers]
[ykaneko0929@gmail.com: fix coding style]
[ykaneko0929@gmail.com: update changelog]
[ykaneko0929@gmail.com: gen3: fix initialization of interrupts]
[ykaneko0929@gmail.com: gen3: fix clearing interrupts]
[ykaneko0929@gmail.com: gen3: add helper function for request_irq()]
[ykaneko0929@gmail.com: gen3: remove IRQF_SHARED flag for request_irq()]
[ykaneko0929@gmail.com: revert ravb_close() and ravb_ptp_stop()]
[ykaneko0929@gmail.com: avoid calling free_irq() to non-hooked interrupts]
[ykaneko0929@gmail.com: make NC/BE interrupt handler a function]
[ykaneko0929@gmail.com: make timestamp interrupt handler a function]
[ykaneko0929@gmail.com: timestamp interrupt is handled in multiple
 interrupt handler instead of dma queue interrupt handler]
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Soheil Hassas Yeganeh says:

====================
add TX timestamping via cmsg

This patch series aim at enabling TX timestamping via cmsg.

Currently, to occasionally sample TX timestamping on a socket,
applications need to call setsockopt twice: first for enabling
timestamps and then for disabling them. This is an unnecessary
overhead. With cmsg, in contrast, applications can sample TX
timestamps per sendmsg().

This patch series adds the code for processing SO_TIMESTAMPING
for cmsg's of the SOL_SOCKET level, and adds the glue code for
TCP, UDP, and RAW for both IPv4 and IPv6. This implementation
supports overriding timestamp generation flags (i.e.,
SOF_TIMESTAMPING_TX_*) but not timestamp reporting flags.
Applications must still enable timestamp reporting via
setsockopt to receive timestamps.

This series does not change existing timestamping behavior for
applications that are using socket options.

I will follow up with another patch to enable timestamping for
active TFO (client-side TCP Fast Open) and also setting packet
mark via cmsgs.

Thanks!

Changes in v2:
        - Replace u32 with __u32 in the documentation.

Changes in v3:
	- Fix the broken build for L2TP (due to changes
	  in IPv6).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update docs and add code snippet for using cmsg for timestamping.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.

Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.

Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Process socket-level control messages by invoking
__sock_cmsg_send in ip6_datagram_send_ctl for control messages on
the SOL_SOCKET layer.

This makes sure whenever ip6_datagram_send_ctl is called for
udp and raw, we also process socket-level control messages.

This is a bit uglier than IPv4, since IPv6 does not have
something like ipcm_cookie. Perhaps we can later create
a control message cookie for IPv6?

Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv6 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Process socket-level control messages by invoking
__sock_cmsg_send in ip_cmsg_send for control messages on
the SOL_SOCKET layer.

This makes sure whenever ip_cmsg_send is called in udp, icmp,
and raw, we also process socket-level control messages.

Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv4 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accept SO_TIMESTAMPING in control messages of the SOL_SOCKET level
as a basis to accept timestamping requests per write.

This implementation only accepts TX recording flags (i.e.,
SOF_TIMESTAMPING_TX_HARDWARE, SOF_TIMESTAMPING_TX_SOFTWARE,
SOF_TIMESTAMPING_TX_SCHED, and SOF_TIMESTAMPING_TX_ACK) in
control messages. Users need to set reporting flags (e.g.,
SOF_TIMESTAMPING_OPT_ID) per socket via socket options.

This commit adds a tsflags field in sockcm_cookie which is
set in __sock_cmsg_send. It only override the SOF_TIMESTAMPING_TX_*
bits in sockcm_cookie.tsflags allowing the control message
to override the recording behavior per write, yet maintaining
the value of other flags.

This patch implements validating the control message and setting
tsflags in struct sockcm_cookie. Next commits in this series will
actually implement timestamping per write for different protocols.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, to avoid a cache line miss for accessing skb_shinfo,
tcp_ack_tstamp skips socket that do not have
SOF_TIMESTAMPING_TX_ACK bit set in sk_tsflags. This is
implemented based on an implicit assumption that the
SOF_TIMESTAMPING_TX_ACK is set via socket options for the
duration that ACK timestamps are needed.

To implement per-write timestamps, this check should be
removed and replaced with a per-packet alternative that
quickly skips packets missing ACK timestamps marks without
a cache-line miss.

To enable per-packet marking without a cache line miss, use
one bit in TCP_SKB_CB to mark a whether a SKB might need a
ack tx timestamp or not. Further checks in tcp_ack_tstamp are not
modified and work as before.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SOF_TIMESTAMPING_OPT_ID is set to get data-independent IDs
to associate timestamps with send calls. For TCP connections,
tp->snd_una is used as the starting point to calculate
relative IDs.

This socket option will fail if set before the handshake on a
passive TCP fast open connection with data in SYN or SYN/ACK,
since setsockopt requires the connection to be in the
ESTABLISHED state.

To address these, instead of limiting the option to the
ESTABLISHED state, accept the SOF_TIMESTAMPING_OPT_ID option as
long as the connection is not in LISTEN or CLOSE states.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To process cmsg's of the SOL_SOCKET level in addition to
cmsgs of another level, protocols can call sock_cmsg_send().
This causes a double walk on the cmsghdr list, one for SOL_SOCKET
and one for the other level.

Extract the inner demultiplex logic from the loop that walks the list,
to allow having this called directly from a walker in the protocol
specific code.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexandre TORGUE says:

====================
Enhance stmmac driver to support GMAC4.x IP

This is a subset of patch to enhance current stmmac driver to support
new GMAC4.x chips. New set of callbacks is defined to support this new
family: descriptors, dma, core.

One of main changes of GMAC 4.xx IP is descriptors management.
 -descriptors are only used in ring mode.
 -A descriptor is composed of 4 32bits registers (no more extended
  descriptors)
 -descriptor mechanism (Tx for example, but it is exactly the same for RX):
 -useful registers:
  -DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
  -DMA_CH#_TxDesc_List_Address: start address of the ring
  -DMA_CH#_TxDesc_Tail_Pointer: address of the last descriptor to send + 1.
  -DMA_CH#_TxDesc_Current_App_TxDesc: address of the current descriptor

 -The descriptor Tail Pointer register contains the pointer to the
  descriptor address (N). The base address and the current
  descriptor decide the address of the current descriptor that the
  DMA can process. The descriptors up to one location less than the
  one indicated by the descriptor tail pointer (N-1) are owned by
  the DMA. The DMA continues to process the descriptors until the
  following condition occurs:
  "current descriptor pointer == Descriptor Tail pointer"

  Then the DMA goes into suspend mode. The application must perform
  a write to descriptor tail pointer register and update the tail
  pointer to have the following condition and to start a new transfer:
  "current descriptor pointer < Descriptor tail pointer"

  The DMA automatically wraps around the base address when the end
  of ring is reached.

New features are available on IP:
 -TSO (TCP Segmentation Offload) for TX only
 -Split header: to have header and payload in 2 different buffers (not yet implemented)

Below some throughput figures obtained on some boxes:

                        iperf (mbps)
--------------------------------------
                       tcp     udp
                    tx   rx   tx  rx
                     -----------------
    GMAC4.x         935  930  750 800

Note: There is a change in 4.10a databook on bitfield mapping of DMA_CHANx_INTR_ENA register.
This requires to have é diffrent set of callbacks between IP 4.00a and 4.10a.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch just updates the driver to the version fully
tested on STi platforms. This version is Jan_2016.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update stmmac driver documentation according to new GMAC 4.x family.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the whole GMAC4 support inside the
stmmac d.d. now able to use the new HW and some new features
i.e.: TSO.
It is missing the multi-queue and split Header support at this
stage.
This patch also updates the driver version and the stmmac.txt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For gmac3, the MMC addr map is: 0x100 - 0x2fc
For gmac4, the MMC addr map is: 0x700 - 0x8fc

So instead of adding 0x600 to the IO address when setup the mmc,
the RMON base address is saved inside the private structure and
then used to manage the counters.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the initial support for GMAC4 that includes
the main callbacks to setup the core module: including
Csum, basic filtering, mac address and interrupt (MMC,
MTL, PMT) No LPI added.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA behavior is linked to descriptor management:

-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
	-DMA_CH#_TxDesc_Tail_Pointer: address of the last
					      descriptor to send + 1.
	-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
						    descriptor

-The descriptor Tail Pointer register contains the pointer to the
 descriptor address (N). The base address and the current
 descriptor decide the address of the current descriptor that the
 DMA can process. The descriptors up to one location less than the
 one indicated by the descriptor tail pointer (N-1) are owned by
 the DMA. The DMA continues to process the descriptors until the
 following condition occurs:
 "current descriptor pointer == Descriptor Tail pointer"

Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"

The DMA automatically wraps around the base address when the end
of ring is reached.

Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the main header file to define all the
macro used for GMAC4 DMA and CORE parts.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
 descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
	-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor
				   ring
	-DMA_CH#_TxDesc_List_Address: start address of the ring
	-DMA_CH#_TxDesc_Tail_Pointer: address of the last
				      descriptor to send + 1.
	-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
					    descriptor

-The descriptor Tail Pointer register contains the pointer to the
 descriptor address (N). The base address and the current
 descriptor decide the address of the current descriptor that the
 DMA can process. The descriptors up to one location less than the
 one indicated by the descriptor tail pointer (N-1) are owned by
 the DMA. The DMA continues to process the descriptors until the
 following condition occurs:
 "current descriptor pointer == Descriptor Tail pointer"

  Then the DMA goes into suspend mode. The application must perform
  a write to descriptor tail pointer register and update the tail
  pointer to have the following condition and to start a new
      transfer:
  "current descriptor pointer < Descriptor tail pointer"

  The DMA automatically wraps around the base address when the end
  of ring is reached.

-New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

synopsys_uid is only used once after setup, to get synopsys_id
by using shitf/mask operation. It's no longer used then.
So, remove this temporary variable and directly compute
synopsys_id from setup routine.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To avoid lot of check in stmmac_main for display ring management
and support the GMAC4 chip, the display_ring function is moved
into dedicated descriptor file.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On next GMAC IP generation (4.xx), the way to get hw feature
is not the same than on previous 3.xx. As it is hardware
dependent, the way to get hw capabilities should be defined in dma ops of
each MAC IP. It will avoid also a huge computation of hw capabilities in
stmmac_main.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support of pause ctrl for HNS V2, and this feature is lost
by HNS V1:
       1) service ports can disable rx pause frame,
       2) debug ports can open tx/rx pause frame.

And this patch updates the REGs about the pause ctrl when updated
status function called by upper layer routine.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since nla_get_in_addr and nla_put_in_addr were implemented,
so use them appropriately.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-SACK connections, cwnd is lowered to inflight plus 3 packets
when the recovery ends. This is an optional feature in the NewReno
RFC 2582 to reduce the potential burst when cwnd is "re-opened"
after recovery and inflight is low.

This feature is questionably effective because of PRR: when
the recovery ends (i.e., snd_una == high_seq) NewReno holds the
CA_Recovery state for another round trip to prevent false fast
retransmits. But if the inflight is low, PRR will overwrite the
moderated cwnd in tcp_cwnd_reduction() later regardlessly. So if a
receiver responds bogus ACKs (i.e., acking future data) to speed up
transfer after recovery, it can only induce a burst up to a window
worth of data packets by acking up to SND.NXT. A restart from (short)
idle or receiving streched ACKs can both cause such bursts as well.

On the other hand, if the recovery ends because the sender
detects the losses were spurious (e.g., reordering). This feature
unconditionally lowers a reverted cwnd even though nothing
was lost.

By principle loss recovery module should not update cwnd. Further
pacing is much more effective to reduce burst. Hence this patch
removes the cwnd moderation feature.

v2 changes: revised commit message on bogus ACKs and burst, and
            missing signature
Signed-off-by: Matt Mathis <mattmathis@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Missing device reference in IPSEC input path results in crashes
    during device unregistration.  From Subash Abhinov Kasiviswanathan.

 2) Per-queue ISR register writes not being done properly in macb
    driver, from Cyrille Pitchen.

 3) Stats accounting bugs in bcmgenet, from Patri Gynther.

 4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
    Quentin Armitage.

 5) SXGBE driver has off-by-one in probe error paths, from Rasmus
    Villemoes.

 6) Fix race in save/swap/delete options in netfilter ipset, from
    Vishwanath Pai.

 7) Ageing time of bridge not set properly when not operating over a
    switchdev device.  Fix from Haishuang Yan.

 8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
    Duyck.

 9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.

10) FEC driver should only access registers that actually exist on the
    given chipset, fix from Fabio Estevam.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
  net: mvneta: fix changing MTU when using per-cpu processing
  stmmac: fix MDIO settings
  Revert "stmmac: Fix 'eth0: No PHY found' regression"
  stmmac: fix TX normal DESC
  net: mvneta: use cache_line_size() to get cacheline size
  net: mvpp2: use cache_line_size() to get cacheline size
  net: mvpp2: fix maybe-uninitialized warning
  tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
  net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
  rtnl: fix msg size calculation in if_nlmsg_size()
  fec: Do not access unexisting register in Coldfire
  net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
  net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
  net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
  net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
  bpf: make padding in bpf_tunnel_key explicit
  ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
  bnxt_en: Fix ethtool -a reporting.
  bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
  bnxt_en: Implement proper firmware message padding.
  ...

Pull clk fixes from Stephen Boyd:
 "A handful of const updates for reset ops and a couple fixes to the
  newly introduced IPQ4019 clock driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll
  clk: qcom: ipq4019: switch remaining defines to enums
  clk: qcom: Make reset_control_ops const
  clk: tegra: Make reset_control_ops const
  clk: sunxi: Make reset_control_ops const
  clk: atlas7: Make reset_control_ops const
  clk: rockchip: Make reset_control_ops const
  clk: mmp: Make reset_control_ops const
  clk: mediatek: Make reset_control_ops const