- 15 May, 2018 1 commit
-
-
Rafał Miłecki authored
brcmfmac is a FullMAC driver and it implements/uses cfg80211 interface for stations management. At the same time it doesn't receive or pass up management frames. This flag indicates that authenticator doesn't have to subscribe to or handle management frames. Some authenticators (e.g. hostapd) were working with brcmfmac thanks to some extra assumptions. This commit clears up the situation. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
- 12 May, 2018 3 commits
-
-
Colin Ian King authored
Trivial fix to spelling mistake in rsi_dbg debug message text Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Lorenzo Bianconi authored
Add a usleep_range in mt76x2_mac_stop routine in order to add a polling delay checking values of MT_MAC_STATUS and IBI_R12 registers Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
-
Toke Høiland-Jørgensen authored
Since the addition of the TXQ stats to cfg80211, the station_info struct has grown to be quite large, which results in warnings when allocated on the stack. Fix the affected places to do dynamic allocations instead. Fixes: 52539ca8 ("cfg80211: Expose TXQ stats and parameters to userspace") Reviewed-by:
Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
- 09 May, 2018 4 commits
-
-
Ganapathi Bhat authored
While carrying energy detection(ED) tests, the chip will stop transmission upon detecting an energy in the connected channel. As a feedback, driver will stop dequeuing TX packets and due to which wmm_tx_pending keep incremeting. Once wmm_tx_pending reaches 100, driver calls netif_tx_stop_queue(). If TX ques is not restarted within 5(watchdog_timeo) seconds, it will result in TX timeout. The ED test is carried out for one minute and the current threshold of 100 is easily overcome by the traffic, cuasing TX timeouts. To fix this increase the threshold to 400. Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Ganapathi Bhat <gbhat@marvell.com> Signed-off-by:
-
Julia Lawall authored
Nothing that is defined in 11ac.h is referenced in cmdevt.c. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Sean Lanigan authored
Add support for the BCM43364 chipset via an SDIO interface, as used in e.g. the Murata 1FX module. The BCM43364 uses the same firmware as the BCM43430 (which is already included), the only difference is the omission of Bluetooth. However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place triggers the brcmfmac driver to load, and then correctly use the firmware file 'brcmfmac43430-sdio.bin'. Signed-off-by:
Sean Lanigan <sean@lano.id.au> Acked-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Ping-Ke Shih authored
Two enumerations bt_total_ant_num and bt_ant_num are identical, so one can be removed. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
- 04 May, 2018 6 commits
-
-
Lorenzo Bianconi authored
Add leftover filter coefficients in IIR rssi estimation Fixes: 7bc04215 ("mt76: add driver code for MT76x2e") Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in module parameter description text Signed-off-by:
-
Lorenzo Bianconi authored
Remove unnecessary break statement in the default case of bw switch block in mt76x2_mac_process_tx_rate routine Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in RT_TRACE message text. Signed-off-by:
-
Stanislaw Gruszka authored
We have check if queue is not empty when start flushing queues on by mac80211 callback, but we also can start flushing queues by internal driver calls. So move check into rt2x00queue_flush_queue() to assure we do not flush empty queue anytime. Additionally add warning if we start to kick empty queue as in such situation we set wrong index in the HW queue, what can confuse the HW and have various negative consequences. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(), we do not need generic version of those. Signed-off-by:
-
- 30 Apr, 2018 23 commits
-
-
Franky Lin authored
Revision 7 of PCIe dongle interface increases the item size of tx and rx complete rings to accommodate extra payload for new feature. This patch simply bump up the size of these two rings without adding the support for utilizing the new space. This makes brcmfmac compatible with rev7 firmware. Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
-
Franky Lin authored
A hostready signal is introduced to inform firmware through mailbox doorbell1 when common ring initialized or D3 exited. Reviewed-by:
-
Arend Van Spriel authored
The information in the firmware mapping does not need to be modified so it can be static const. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
-
Franky Lin authored
The enum nl80211_band used to retrieve wiphy->bands is the same as wiphy->bands->band which is checked by wiphy_register(). So it can be used directly as parameter of ieee80211_channel_to_frequency(). Reviewed-by:
-
Franky Lin authored
Provides a timestamp in bss information so user space can see when the bss info was updated. Since tsf is not available from the dongle events boottime is reported instead. Reported-by:
Dmitry Shmidt <dimitrysh@google.com> Reviewed-by:
-
Arend Van Spriel authored
The mac address for p2pdev must be different from the primary interface due to firmware requirement. Add an explicit check for this requirement if user-space provides a mac address. Reviewed-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in comment and in the ord_data text Signed-off-by:
-
Colin Ian King authored
Rename several macros that contain mispellings of UNKNOWN Signed-off-by:
-
Gustavo A. R. Silva authored
There is a potential execution path in which variable ret is returned without being properly initialized previously. Fix this by storing the value returned by function rsi_usb_master_reg_write into _ret_. Addresses-Coverity-ID: 1468407 ("Uninitialized scalar variable") Fixes: 16d3bb7b ("rsi: disable fw watchdog timer during reset") Signed-off-by:Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Function rsi_hal_key_config returns before reaching code at line 922 if (status), hence this code is structurally dead. Fix this by storing the value returned by rsi_hal_load_key into _status_ for its further evaluation and use. Addresses-Coverity-ID: 1468409 ("Structurally dead code") Fixes: 4fd6c476 ("rsi: roaming enhancements") Signed-off-by: -
Eyal Reizer authored
pm_runtime handles sdio power on and power off transitions. An old workaround for trying to control the power explicitly from the driver was in fact causing failures on suspend/resume as the mmc layer already power the module on resume. In case of resume pm_runtime_get sync returns a positive device's usage count causing the driver to try an re-initialize an already initialized device. This was causing sdio bus failure on resume. Remove this manual power on/off sequence as it is in-fact not needed. Signed-off-by:
Eyal Reizer <eyalr@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Luc Van Oostenryck authored
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, but the implementation in this driver returns an 'int'. Fix this by returning 'netdev_tx_t' in this driver too. Signed-off-by:
Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Reviewed-by:
-
Jia-Ju Bai authored
dma_tx_fragment() is never called in atomic context. dma_tx_fragment() is only called by b43legacy_dma_tx(), which is only called by b43legacy_tx_work(). b43legacy_tx_work() is only set a parameter of INIT_WORK() in b43legacy_wireless_init(). Despite never getting called from atomic context, dma_tx_fragment() calls alloc_skb() with GFP_ATOMIC, which does not sleep for allocation. GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL, which can sleep and improve the possibility of sucessful allocation. This is found by a static analysis tool named DCNS written by myself. And I also manually check it. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
-
Xinming Hu authored
During changing virtual interface, keep using previous net device mac address. Signed-off-by:
Xinming Hu <huxm@marvell.com> Signed-off-by:
-
Xinming Hu authored
When interface type changed, firmware using a new connction pointer. We need Re-configure the mac address. Signed-off-by:
-
Xinming Hu authored
For user configurated mac address, directly set to firmware with no change. Signed-off-by:
-
Luc Van Oostenryck authored
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, but the implementation in this driver returns an 'int'. Fix this by returning 'netdev_tx_t' in this driver too. Signed-off-by:
-
Felix Fietkau authored
The check within mt76_txq_send_burst is not enough, as it happens after a first frame has already been queued up Signed-off-by:
-
Felix Fietkau authored
Fixes a reported lockdep error in mac80211: [ 179.867321] ============================= [ 179.871510] WARNING: suspicious RCU usage [ 179.875528] 4.14.32 #0 Not tainted [ 179.878924] ----------------------------- [ 179.882981] backports-2017-11-01/net/mac80211/tx.c:594 suspicious rcu_dereference_check() usage! [ 179.891785] [ 179.891785] other info that might help us debug this: [ 179.891785] [ 179.899824] [ 179.899824] rcu_scheduler_active = 2, debug_locks = 1 [ 179.906343] 2 locks held by ksoftirqd/0/7: [ 179.910479] #0: (&(&q->lock)->rlock){+.-.}, at: [<86b207a4>] mt76_dma_tx_cleanup+0x64/0x354 [mt76] [ 179.919734] #1: (&(&fq->lock)->rlock){+.-.}, at: [<87238410>] ieee80211_tx_dequeue+0x54/0xc3c [mac80211] [ 179.929890] [ 179.929890] stack backtrace: [ 179.934257] CPU: 0 PID: 7 Comm: ksoftirqd/0 Not tainted 4.14.32 #0 [ 179.940421] Stack : 00000000 00000000 00000000 00000000 80e0fce2 00000036 00000000 00000000 [ 179.948864] 87c3d24c 80696377 8061039c 00000000 00000007 00000001 87c5db78 6534689d [ 179.957306] 00000000 00000000 80e10000 87c5da74 00000001 0000015a 00000007 00000000 [ 179.965748] 00000000 806a0000 000e4171 00000000 00000000 00000000 ffffffff 00000001 [ 179.974189] 806c0000 8692b240 86b000d0 87316fe4 00000001 802c9a68 00000000 80700000 [ 179.982632] ... [ 179.985104] Call Trace: [ 179.987582] [<80010a48>] show_stack+0x58/0x100 [ 179.992040] [<804c2c58>] dump_stack+0xe8/0x170 [ 179.996868] [<87234a04>] ieee80211_tx_h_select_key+0xa8/0x5b8 [mac80211] [ 180.004299] [<87238d44>] ieee80211_tx_dequeue+0x988/0xc3c [mac80211] [ 180.011048] [<86b230dc>] mt76_txq_schedule+0x110/0x3a4 [mt76] [ 180.016821] [<86b209d0>] mt76_dma_tx_cleanup+0x290/0x354 [mt76] [ 180.022777] [<86be2e60>] mt7603_tx_tasklet+0x40/0x6c [mt7603e] [ 180.028637] [<80037058>] tasklet_action+0x110/0x1ec [ 180.033532] [<804e1dac>] __do_softirq+0x164/0x35c [ 180.038235] [<80037174>] run_ksoftirqd+0x40/0x84 [ 180.042870] [<800580c8>] smpboot_thread_fn+0x1a8/0x1d8 [ 180.048023] [<800542e8>] kthread+0x130/0x144 [ 180.052297] [<8000b1f8>] ret_from_kernel_thread+0x14/0x1c Signed-off-by: -
Felix Fietkau authored
Avoids having the tid or station entry disappear prematurely. Also cancel the reorder work earlier to avoid further processing delayed by waiting for the lock to be released Signed-off-by:
-
Felix Fietkau authored
Add a spinlock in mt76_rx_complete. Without this, multiple stats updates could happen in parallel, which can lead to deadlocks. There are probably more corner cases fixed by this change. Signed-off-by:
-
Lorenzo Bianconi authored
Fix is_mt7612 routine since asic version is set in mt76_dev revision field and not in mt76x2_dev one. Moreover remove mt76x2_dev rev field since it is never used in the driver Fixes: 7bc04215 ('mt76: add driver code for MT76x2e') Signed-off-by:
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2018-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next Second batch of iwlwifi patches for 4.18 * Some preparations for new hardware; * A workaround to rescan the bus for the rare situation when older devices become irresponsive, * Hardening of the firmware loading code to avoid issues with corrupted files; * A few clean-ups and bugfixes.
-
- 26 Apr, 2018 3 commits
-
-
Eliad Peller authored
In case of "any" wowlan trigger is configured, no valid wakeup filter was configured. Moreover, the fw assumes there's no connection when there are no configured wakeup filters. This leads to the station info not being updated on D3 command, causing rate_n_flags to be 0 when the offloading code sends tx frame (triggering SYSASSERT_102C due to invalid antenna param) Note: "any" trigger is currently assumed to only be used when entering d0i3 (which has a different flow). However, we still reach this code when using d3_test. Signed-off-by:
Eliad Peller <eliadx.peller@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com>
-
Sara Sharon authored
Firmware will only send non low-latency TIDs in the bitmap, so the check is now redundant. Signed-off-by:
Sara Sharon <sara.sharon@intel.com> Signed-off-by:
-
Luca Coelho authored
The bitfield we use in struct iwl_cfg contains 17 bits, but we declare it as u16. The compiler doesn't seem to have any problems with that (it probably automatically makes it u32), but it's cleaner to use a type that is long enough for all the flags. Signed-off-by:
-
