- 25 Jun, 2019 40 commits
-
-
ShihPo Hung authored
commit bf587caa upstream. Because RISC-V compliant implementations can cache invalid entries in TLB, an SFENCE.VMA is necessary after changes to the page table. This patch adds an SFENCE.vma for the vmalloc_fault path. Signed-off-by:
ShihPo Hung <shihpo.hung@sifive.com> [paul.walmsley@sifive.com: reversed tab->whitespace conversion, wrapped comment lines] Signed-off-by:
Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@sifive.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: linux-riscv@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Willem de Bruijn authored
commit fd704bd5 upstream. CAN supports software tx timestamps as of the below commit. Purge any queued timestamp packets on socket destroy. Fixes: 51f31cab ("ip: support for TX timestamps on UDP and RAW sockets") Reported-by: syzbot+a90604060cb40f5bdd16@syzkaller.appspotmail.com Signed-off-by:
Willem de Bruijn <willemb@google.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Joakim Zhang authored
commit 247e5356 upstream. Current we can meet timeout issue when setting a small bitrate like 10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock = 30MHZ): | root@imx6ul7d:~# ip link set can0 up type can bitrate 10000 A link change request failed with some changes committed already. Interface can0 may have been left with an inconsistent configuration, please check. | RTNETLINK answers: Connection timed out It is caused by calling of flexcan_chip_unfreeze() timeout. Originally the code is using usleep_range(10, 20) for unfreeze operation, but the patch (8badd65e can: flexcan: avoid calling usleep_range from interrupt context) changed it into udelay(10) which is only a half delay of before, there're also some other delay changes. After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue. Meanwhile, Rasmus Villemoes reported that even with a timeout of 100, flexcan_probe() fails on the MPC8309, which requires a value of at least 140 to work reliably. 250 works for everyone. Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Reviewed-by:
Dong Aisheng <aisheng.dong@nxp.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
Anssi Hannula authored
commit 904044dd upstream. Commit 9e5f1b27 ("can: xilinx_can: add support for Xilinx CAN FD core") added a new can_bittiming_const structure for CAN FD cores that support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN cores, but the commit did not actually take that into use. Fix that. Tested with CAN FD core on a ZynqMP board. Fixes: 9e5f1b27 ("can: xilinx_can: add support for Xilinx CAN FD core") Reported-by:
Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com> Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Reviewed-by:
-
Naohiro Aota authored
commit c4e0540d upstream. Currently, btrfs does not consult seed devices to start readahead. As a result, if readahead zone is added to the seed devices, btrfs_reada_wait() indefinitely wait for the reada_ctl to finish. You can reproduce the hung by modifying btrfs/163 to have larger initial file size (e.g. xfs_io pwrite 4M instead of current 256K). Fixes: 7414a03f ("btrfs: initial readahead code and prototypes") Cc: stable@vger.kernel.org # 3.2+: ce7791ff: Btrfs: fix race between readahead and device replace/removal Cc: stable@vger.kernel.org # 3.2+ Reviewed-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 1dac6f5b ] gcc gets a bit confused by the logic in ovl_setup_trap() and can't figure out whether the local 'trap' variable in the caller was initialized or not: fs/overlayfs/super.c: In function 'ovl_fill_super': fs/overlayfs/super.c:1333:4: error: 'trap' may be used uninitialized in this function [-Werror=maybe-uninitialized] iput(trap); ^~~~~~~~~~ fs/overlayfs/super.c:1312:17: note: 'trap' was declared here Reword slightly to make it easier for the compiler to understand. Fixes: 146d62e5 ("ovl: detect overlapping layers") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Miklos Szeredi authored
[ Upstream commit 9179c21d ] NFS mounts can be disconnected from fs root. Don't fail the overlapping layer check because of this. The check is not authoritative anyway, since topology can change during or after the check. Reported-by:
Antti Antinoja <antti@fennosys.fi> Signed-off-by:
-
Amir Goldstein authored
[ Upstream commit 146d62e5 ] Overlapping overlay layers are not supported and can cause unexpected behavior, but overlayfs does not currently check or warn about these configurations. User is not supposed to specify the same directory for upper and lower dirs or for different lower layers and user is not supposed to specify directories that are descendants of each other for overlay layers, but that is exactly what this zysbot repro did: https://syzkaller.appspot.com/x/repro.syz?x=12c7a94f400000 Moving layer root directories into other layers while overlayfs is mounted could also result in unexpected behavior. This commit places "traps" in the overlay inode hash table. Those traps are dummy overlay inodes that are hashed by the layers root inodes. On mount, the hash table trap entries are used to verify that overlay layers are not overlapping. While at it, we also verify that overlay layers are not overlapping with directories "in-use" by other overlay instances as upperdir/workdir. On lookup, the trap entries are used to verify that overlay layers root inodes have not been moved into other layers after mount. Some examples: $ ./run --ov --samefs -s ... ( mkdir -p base/upper/0/u base/upper/0/w base/lower lower upper mnt mount -o bind base/lower lower mount -o bind base/upper upper mount -t overlay none mnt ... -o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w) $ umount mnt $ mount -t overlay none mnt ... -o lowerdir=base,upperdir=upper/0/u,workdir=upper/0/w [ 94.434900] overlayfs: overlapping upperdir path mount: mount overlay on mnt failed: Too many levels of symbolic links $ mount -t overlay none mnt ... -o lowerdir=upper/0/u,upperdir=upper/0/u,workdir=upper/0/w [ 151.350132] overlayfs: conflicting lowerdir path mount: none is already mounted or mnt busy $ mount -t overlay none mnt ... -o lowerdir=lower:lower/a,upperdir=upper/0/u,workdir=upper/0/w [ 201.205045] overlayfs: overlapping lowerdir path mount: mount overlay on mnt failed: Too many levels of symbolic links $ mount -t overlay none mnt ... -o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w $ mv base/upper/0/ base/lower/ $ find mnt/0 mnt/0 mnt/0/w find: 'mnt/0/w/work': Too many levels of symbolic links find: 'mnt/0/u': Too many levels of symbolic links Reported-by: syzbot+9c69c282adc4edd2b540@syzkaller.appspotmail.com Signed-off-by:
Amir Goldstein <amir73il@gmail.com> Signed-off-by:
-
Jaesoo Lee authored
[ Upstream commit c8e8c77b ] The Number of Namespaces (nn) field in the identify controller data structure is defined as u32 and the maximum allowed value in NVMe specification is 0xFFFFFFFEUL. This change fixes the possible overflow of the DIV_ROUND_UP() operation used in nvme_scan_ns_list() by casting the nn to u64. Signed-off-by:
Jaesoo Lee <jalee@purestorage.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
Dave Martin authored
[ Upstream commit ebcc5928 ] Since GCC 9, the compiler warns about evolution of the platform-specific ABI, in particular relating for the marshaling of certain structures involving bitfields. The kernel is a standalone binary, and of course nobody would be so stupid as to expose structs containing bitfields as function arguments in ABI. (Passing a pointer to such a struct, however inadvisable, should be unaffected by this change. perf and various drivers rely on that.) So these warnings do more harm than good: turn them off. We may miss warnings about future ABI drift, but that's too bad. Future ABI breaks of this class will have to be debugged and fixed the traditional way unless the compiler evolves finer-grained diagnostics. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Robert Hancock authored
[ Upstream commit 4a60570d ] Some chips have attributes which exist on more than one page but the attribute is not presently marked as paged. This causes the attributes to be generated with the same label, which makes it impossible for userspace to tell them apart. Marking all such attributes as paged would result in the page suffix being added regardless of whether they were present on more than one page or not, which might break existing setups. Therefore, we add a second check which treats the attribute as paged, even if not marked as such, if it is present on multiple pages. Fixes: b4ce237b ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers") Signed-off-by:
Robert Hancock <hancock@sedsystems.ca> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Eduardo Valentin authored
[ Upstream commit c41dd48e ] Drivers may register to hwmon and request for also registering with the thermal subsystem (HWMON_C_REGISTER_TZ). However, some of these driver, e.g. marvell phy, may be probed from Device Tree or being dynamically allocated, and in the later case, it will not have a dev->of_node entry. Registering with hwmon without the dev->of_node may result in different outcomes depending on the device tree, which may be a bit misleading. If the device tree blob has no 'thermal-zones' node, the *hwmon_device_register*() family functions are going to gracefully succeed, because of-thermal, *thermal_zone_of_sensor_register() return -ENODEV in this case, and the hwmon error path handles this error code as success to cover for the case where CONFIG_THERMAL_OF is not set. However, if the device tree blob has the 'thermal-zones' entry, the *hwmon_device_register*() will always fail on callers with no dev->of_node, propagating -EINVAL. If dev->of_node is not present, calling of-thermal does not make sense. For this reason, this patch checks first if the device has a of_node before going over the process of registering with the thermal subsystem of-thermal interface. And in this case, when a caller of *hwmon_device_register*() with HWMON_C_REGISTER_TZ and no dev->of_node will still register with hwmon, but not with the thermal subsystem. If all the hwmon part bits are in place, the registration will succeed. Fixes: d560168b ("hwmon: (core) New hwmon registration API") Cc: Jean Delvare <jdelvare@suse.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-hwmon@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Eduardo Valentin <eduval@amazon.com> Signed-off-by:
-
Alexandra Winter authored
[ Upstream commit 33572619 ] Enabling sysfs attribute bridge_hostnotify triggers a series of udev events for the MAC addresses of all currently connected peers. In case no VLAN is set for a peer, the device reports the corresponding MAC addresses with VLAN ID 4096. This currently results in attribute VLAN=4096 for all non-VLAN interfaces in the initial series of events after host-notify is enabled. Instead, no VLAN attribute should be reported in the udev event for non-VLAN interfaces. Only the initial events face this issue. For dynamic changes that are reported later, the device uses a validity flag. This also changes the code so that it now sets the VLAN attribute for MAC addresses with VID 0. On Linux, no qeth interface will ever be registered with VID 0: Linux kernel registers VID 0 on all network interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0. Peers with other OSs could register MACs with VID 0. Fixes: 9f48b9db ("qeth: bridgeport support - address notifications") Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Julian Wiedmann authored
[ Upstream commit 0cd6783d ] While qeth_l3 uses netif_keep_dst() to hold onto the dst, a skb's dst may still have been obsoleted (via dst_dev_put()) by the time that we end up using it. The dst then points to the loopback interface, which means the neighbour lookup in qeth_l3_get_cast_type() determines a bogus cast type of RTN_BROADCAST. For IQD interfaces this causes us to place such skbs on the wrong HW queue, resulting in TX errors. Fix-up the various call sites to first validate the dst entry with dst_check(), and fall back accordingly. Signed-off-by:
-
Julian Wiedmann authored
[ Upstream commit 72c87976 ] When selecting the cast type of a neighbourless IPv4 skb (eg. on a raw socket), qeth_l3 falls back to the packet's destination IP address. For this case we should classify traffic sent to 255.255.255.255 as broadcast. This fixes DHCP requests, which were misclassified as unicast (and for IQD interfaces thus ended up on the wrong HW queue). Signed-off-by:
-
Christian Brauner authored
[ Upstream commit 1fcd0eb3 ] Define __NR_pidfd_send_signal if it isn't to prevent a potential compilation error. To make pidfd-test compile on all arches, irrespective of whether or not syscall numbers are assigned, define the syscall number to -1. If it isn't defined this will cause the kernel to return -ENOSYS. Fixes: 575a0ae9 ("selftests: add tests for pidfd_send_signal()") Signed-off-by:
Christian Brauner <christian@brauner.io> Signed-off-by:
-
Lucas Stach authored
[ Upstream commit 283f1e38 ] unmap_udmabuf fails to actually unmap the scatterlist, leaving dangling mappings around. Fixes: fbb0de79 ("Add udmabuf misc device") Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Link: http://patchwork.freedesktop.org/patch/msgid/20190604202331.17482-1-l.stach@pengutronix.deSigned-off-by:
Gerd Hoffmann <kraxel@redhat.com> Signed-off-by:
-
Miaohe Lin authored
[ Upstream commit ceae266b ] There's some NICs, such as hinic, with NETIF_F_IP_CSUM and NETIF_F_TSO on but NETIF_F_HW_CSUM off. And ipvlan device features will be NETIF_F_TSO on with NETIF_F_IP_CSUM and NETIF_F_IP_CSUM both off as IPVLAN_FEATURES only care about NETIF_F_HW_CSUM. So TSO will be disabled in netdev_fix_features. For example: Features for enp129s0f0: rx-checksumming: on tx-checksumming: on tx-checksum-ipv4: on tx-checksum-ip-generic: off [fixed] tx-checksum-ipv6: on Fixes: a188222b ("net: Rename NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK") Signed-off-by:
Miaohe Lin <linmiaohe@huawei.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit cc8f5260 ] We need to drop the "ctrl_info->sync_request_sem" lock before returning. Fixes: 6c223761 ("smartpqi: initial commit of Microsemi smartpqi driver") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Avri Altman authored
[ Upstream commit 1c90836f ] struct ufs_dev_cmd is the main container that supports device management commands. In the case of a read descriptor request, we assume that the proper space was allocated in dev_cmd to hold the returning descriptor. This is no longer true, as there are flows that doesn't use dev_cmd for device management requests, and was wrong in the first place. Fixes: d44a5f98 (ufs: query descriptor API) Signed-off-by:
Avri Altman <avri.altman@wdc.com> Reviewed-by:
Alim Akhtar <alim.akhtar@samsung.com> Acked-by:
Bean Huo <beanhuo@micron.com> Signed-off-by:
-
Russell King authored
[ Upstream commit 77316763 ] Avoid reducing the support mask as a result of the interface type selected for SFP modules, or when setting the link settings through ethtool - this should only change when the supported link modes of the hardware combination change. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
George G. Davis authored
[ Upstream commit 4f45d62a ] The following error occurs for the `make ARCH=arm64 checkstack` case: aarch64-linux-gnu-objdump -d vmlinux $(find . -name '*.ko') | \ perl ./scripts/checkstack.pl arm64 wrong or unknown architecture "arm64" As suggested by Masahiro Yamada, fix the above error using regular expressions in the same way it was fixed for the `ARCH=x86` case via commit fda9f990 ("scripts/checkstack.pl: automatically handle 32-bit and 64-bit mode for ARCH=x86"). Suggested-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
George G. Davis <george_davis@mentor.com> Signed-off-by:
-
Trevor Bourget authored
[ Upstream commit a6e04877 ] The buildtar script might want to invoke a make, so tell the parent make to pass the jobserver token pipe to the subcommand by prefixing the command with a +. This addresses the issue seen here: /bin/sh ../scripts/package/buildtar tar-pkg make[3]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule. See https://www.gnu.org/software/make/manual/html_node/Job-Slots.html for more information. Signed-off-by:
Trevor Bourget <tgb.kernel@gmail.com> Signed-off-by:
-
Minwoo Im authored
[ Upstream commit 3562f5d9 ] The WRITE ZEROES command has no data transfer so that we need to initialize the struct (nvmet_req *req)->data_len to 0x0. While (nvmet_req *req)->transfer_len is initialized in nvmet_req_init(), data_len will be initialized by nowhere which might cause the failure with status code NVME_SC_SGL_INVALID_DATA | NVME_SC_DNR randomly. It's because nvmet_req_execute() checks like: if (unlikely(req->data_len != req->transfer_len)) { req->error_loc = offsetof(struct nvme_common_command, dptr); nvmet_req_complete(req, NVME_SC_SGL_INVALID_DATA | NVME_SC_DNR); } else req->execute(req); This patch fixes req->data_len not to be a randomly assigned by initializing it to 0x0 when preparing the command in nvmet_bdev_parse_io_cmd(). nvmet_file_parse_io_cmd() which is for file-backed I/O has already initialized the data_len field to 0x0, though. Cc: Christoph Hellwig <hch@lst.de> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Chaitanya Kulkarni <Chaitanya.Kulkarni@wdc.com> Signed-off-by:
Minwoo Im <minwoo.im.dev@gmail.com> Reviewed-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by:
-
Robin Murphy authored
[ Upstream commit 1c810739 ] On the Arm Juno platform, the HDLCD pixel clock is constrained to 250KHz resolution in order to avoid the tiny System Control Processor spending aeons trying to calculate exact PLL coefficients. This means that modes like my oddball 1600x1200 with 130.89MHz clock get rejected since the rate cannot be matched exactly. In practice, though, this mode works quite happily with the clock at 131MHz, so let's relax the check to allow a little bit of slop. Signed-off-by:
Robin Murphy <robin.murphy@arm.com> Signed-off-by:
Liviu Dudau <liviu.dudau@arm.com> Signed-off-by:
-
Robin Murphy authored
[ Upstream commit b96151ed ] Rather than allowing any old mode through, then subsequently refusing unmatchable clock rates in atomic_check when it's too late to back out and pick a different mode, let's do that validation up-front where it will cause unsupported modes to be correctly pruned in the first place. This also eliminates an issue whereby a perceived clock rate of 0 would cause atomic disable to fail and prevent the module from being unloaded. Signed-off-by:
-
Wen He authored
[ Upstream commit 6a88e0c1 ] This patch trying to fix monitor freeze issue caused by drm error 'flip_done timed out' on LS1028A platform. this set try is make a loop around the second setting CVAL and try like 5 times before giveing up. Signed-off-by:
Wen He <wen.he_1@nxp.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 67c0aaa1 ] sysctl setting bc_forwarding for $rp2 is needed when ping_test_from h2, otherwise the bc packets from $rp2 won't be forwarded. This patch is to add this setting for $rp2. Also, as ping_test_from does grep "$from" only, which could match some unexpected output, some test case doesn't really work, like: # ping_test_from $h2 198.51.200.255 198.51.200.2 PING 198.51.200.255 from 198.51.100.2 veth3: 56(84) bytes of data. 64 bytes from 198.51.100.1: icmp_seq=1 ttl=64 time=0.336 ms When doing grep $form (198.51.200.2), the output could still match. So change to grep "bytes from $from" instead. Fixes: 40f98b9a ("selftests: add a selftest for directed broadcast forwarding") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Sean Wang authored
[ Upstream commit 880c2d4b ] Should only enable HW RX_2BYTE_OFFSET function in the case NET_IP_ALIGN equals to 2. Signed-off-by:
Mark Lee <mark-mc.lee@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
Sean Wang authored
[ Upstream commit 9e4f56f1 ] Should hw_feature as hardware capability flags to check if hardware LRO got support. Signed-off-by:
-
Young Xiao authored
[ Upstream commit 56cd0aef ] The PERF_EVENT_IOC_PERIOD ioctl command can be used to change the sample period of a running perf_event. Consequently, when calculating the next event period, the new period will only be considered after the previous one has overflowed. This patch changes the calculation of the remaining event ticks so that they are offset if the period has changed. See commit 3581fe0e ("ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD") for details. Signed-off-by:
Young Xiao <92siuyang@gmail.com> Signed-off-by:
-
Gen Zhang authored
[ Upstream commit 80caf435 ] In get_vdev_port_node_info(), 'node_info->vdev_port.name' is allcoated by kstrdup_const(), and it returns NULL when fails. So 'node_info->vdev_port.name' should be checked. Signed-off-by:
Gen Zhang <blackgod016574@gmail.com> Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit 2e1f1648 ] When doing a loopback test at copper ports, the serdes loopback and the phy loopback will fail, because of the adjust link had not finished, and phy not ready. Adds sleep between adjust link and test process to fix it. Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Nikita Yushchenko authored
[ Upstream commit 62394708 ] When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error message is logged: failed to kill vid 0081/0 for device eth_cu_1000_4 This is caused by call from __vlan_vid_del() with vin set to zero, over call chain this results into _mv88e6xxx_port_vlan_del() called with vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL. On symmetric path moving port up, call goes through mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan() that returns -EOPNOTSUPP for zero vid. This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for zero vid, then this error code is explicitly cleared in dsa_slave_vlan_rx_kill_vid() and error message is no longer logged. Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
Naresh Kamboju authored
[ Upstream commit bc2cce3f ] Add test_vmalloc.sh to TEST_FILES to make sure it gets installed for run_vmtests. Fixed below error: ./run_vmtests: line 217: ./test_vmalloc.sh: No such file or directory Tested with: make TARGETS=vm install INSTALL_PATH=$PWD/x Signed-off-by:
Naresh Kamboju <naresh.kamboju@linaro.org> Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Alakesh Haloi authored
[ Upstream commit 98a13a8d ] Fixes following compiler warning userfaultfd.c: In function ‘usage’: userfaultfd.c:126:2: warning: format not a string literal and no format arguments [-Wformat-security] fprintf(stderr, examples); Signed-off-by:
Alakesh Haloi <alakesh.haloi@gmail.com> Reviewed-by:
Peter Xu <peterx@redhat.com> Reviewed-by:
Mike Rapoport <rppt@linux.ibm.com> Signed-off-by:
-
Alex Shi authored
[ Upstream commit f97f3f88 ] The test_core will skip the test_cgcore_no_internal_process_constraint_on_threads test case if the 'cpu' controller missing in root's subtree_control. In fact we need to set the 'cpu' in subtree_control, to make the testing meaningful. ./test_core ... ok 4 # skip test_cgcore_no_internal_process_constraint_on_threads ... Signed-off-by:
Alex Shi <alex.shi@linux.alibaba.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: Claudio Zumbo <claudioz@fb.com> Cc: Claudio <claudiozumbo@gmail.com> Cc: linux-kselftest@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reviewed-by:
Roman Gushchin <guro@fb.com> Acked-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Alex Shi authored
[ Upstream commit 00e38a5d ] The cgroup testing relys on the root cgroup's subtree_control setting, If the 'memory' controller isn't set, some test cases will be failed as following: $sudo ./test_core not ok 1 test_cgcore_internal_process_constraint ok 2 test_cgcore_top_down_constraint_enable not ok 3 test_cgcore_top_down_constraint_disable ... To correct this unexpected failure, this patch write the 'memory' to subtree_control of root to get a right result. Signed-off-by:
-
Alex Shi authored
[ Upstream commit f6131f28 ] The cgroup testing relies on the root cgroup's subtree_control setting, If the 'memory' controller isn't set, all test cases will be failed as following: $ sudo ./test_memcontrol not ok 1 test_memcg_subtree_control not ok 2 test_memcg_current ok 3 # skip test_memcg_min not ok 4 test_memcg_low not ok 5 test_memcg_high not ok 6 test_memcg_max not ok 7 test_memcg_oom_events ok 8 # skip test_memcg_swap_max not ok 9 test_memcg_sock not ok 10 test_memcg_oom_group_leaf_events not ok 11 test_memcg_oom_group_parent_events not ok 12 test_memcg_oom_group_score_events To correct this unexpected failure, this patch write the 'memory' to subtree_control of root to get a right result. Signed-off-by:
-
Guenter Roeck authored
[ Upstream commit adefd051 ] Since commit 9012d011 ("compiler: allow all arches to enable CONFIG_OPTIMIZE_INLINING"), xtensa:tinyconfig fails to build with section mismatch errors. WARNING: vmlinux.o(.text.unlikely+0x68): Section mismatch in reference from the function ___pa() to the function .meminit.text:memblock_reserve() WARNING: vmlinux.o(.text.unlikely+0x74): Section mismatch in reference from the function mem_reserve() to the function .meminit.text:memblock_reserve() FATAL: modpost: Section mismatches detected. This was not seen prior to the above mentioned commit because mem_reserve() was always inlined. Mark mem_reserve(() as __init_memblock to have it reside in the same section as memblock_reserve(). Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
