- 27 Jul, 2015 8 commits
-
-
Rabin Vincent authored
BGPIO_F_UNREADABLE_REG_SET is incorrect, since the set register _is_ readable. What's really required is BGPIO_F_READ_OUTPUT_REG_SET: reading the set register reads the set output value. Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Ulrich Hecht authored
R-Car Gen3's GPIO blocks are identical to Gen2's in every respect. Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Sebastian Andrzej Siewior authored
This patch converts gpio_bank.lock from a spin_lock into a raw_spin_lock. The call path is to access this lock is always under a raw_spin_lock, for instance - __setup_irq() holds &desc->lock with irq off + __irq_set_trigger() + omap_gpio_irq_type() - handle_level_irq() (runs with irqs off therefore raw locks) + mask_ack_irq() + omap_gpio_mask_irq() This fixes the obvious backtrace on -RT. However the locking vs context is not and this is not limited to -RT: - omap_gpio_irq_type() is called with IRQ off and has an conditional call to pm_runtime_get_sync() which may sleep. Either it may happen or it may not happen but pm_runtime_get_sync() should not be called with irqs off. - omap_gpio_debounce() is holding the lock with IRQs off. + omap2_set_gpio_debounce() + clk_prepare_enable() + clk_prepare() this one might sleep. The number of users of gpiod_set_debounce() / gpio_set_debounce() looks low but still this is not good. Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
This variable is used as an iterator and initialized in the list_for_each() loop. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Uwe Kleine-König authored
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Uwe Kleine-König authored
The gpio controller on MPC5125 is identical to the MPC5121 register wise, the only difference is that the lines 0..3 are input only instead of 28..31 on MPC5121. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Uwe Kleine-König authored
The gpio controllers that are handled by the mpc8xxx driver differ slightly. Up to now some differences were handled by use of of_device_is_compatible, others by use of struct of_device_id's data. To make this consistent and easily extendable handle the differences at a single place. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Uwe Kleine-König authored
This variable is not modified in the driver and all functions it it passed to don't change it either. So it can and should be marked const. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 21 Jul, 2015 1 commit
-
-
Linus Walleij authored
Now I am very fed up with people reinventing kernel wheels in userspace "just because they can" (read, sysfs). Put in a angry blurb in sysfs doc and put in a new file with pointers to other subsystem drivers utilizing GPIOs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 17 Jul, 2015 4 commits
-
-
-
Vitaly Andrianov authored
Interrupts for GPIOs 16 through 31 are enabled by bit 1 in the "binten" register (offset 8). Previous versions of GPIO only used bit 0, which enables GPIO 0-15 interrupts. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
git://git.pengutronix.de/git/ukl/linuxLinus Walleij authored
The last patch in this series makes the flags parameter for the various gpiod_get* functions mandatory and so allows to remove an ugly cpp hack introduced in commit 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions) for v3.17-rc1. The other nine commits fix the last remaining users of these functions that don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the gpiod functions needs fixing anyhow.)
-
Krzysztof Kozlowski authored
Value returned by devm_ioremap_resource() was checked for non-NULL but devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of error this could lead to dereference of ERR_PTR. Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 16 Jul, 2015 9 commits
-
-
Laurent Navet authored
ret is assigned value from of_property_read_string_index but is overwritten before being used so remove it. Also fix coverity CID 1309759 Reported-by: coverity (CID 1309759) Signed-off-by: Laurent Navet <laurent.navet@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Nicholas Krause authored
This fixes the build warning , warning: cast from pointer to integer of different size when building this file on a x86 allmodconfig configuration. In order for me to fix this build warning I changed the cast in the function mmio_74xx_gpio_probe from casting the variable data of the stucture pointer of_id to uintptr_t rather then unsigned when assigning to the variable flag of the structure pointer priv of the structure type mmio_74xx_gpio_priv. Signed-off-by: Nicholas Krause <xerofoify@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Grygorii Strashko authored
Assign GPIO chip owner field to chip->dev->driver->owner if it was not configured by GPIO driver. Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Grygorii Strashko authored
Now nothing prevents GPIO driver from being unloaded if its gpios were requested as GPIO IRQs only (without calling gpio_request()). Hence, add calls of try_module_get()/module_put() into gpiochip_irq_reqres/relres() to track such scenario properly. Cc: Johan Hovold <johan@kernel.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Grygorii Strashko authored
The spinlock 'slock' is used now to protect pcf857x_irq() from itself which is unnecessary (especially after switching to use threaded IRQs). Hence, remove it and use mutex to protect device data in IRQ handler. Cc: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Geert Uytterhoeven authored
Currently gpio modules are runtime-resumed at probe time. This means the gpio module will be active all the time (except during system suspend, if not configured as a wake-up source). While an R-Car Gen2 gpio module retains pins configured for output at the requested level while put in standby mode, gpio registercannot be accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be called from all contexts where gpio register access is needed. Hence move the Runtime PM handling from probe/remove time to gpio request/free time, which is probably the best we can do. On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6 for SD-Card CD & WP, gpio7 for keys and regulators). Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Geert Uytterhoeven authored
Since commit 59032702 ("ARM: shmobile: Remove legacy platform devices from EMEV2 SoC code"), EMMA Mobile SoCs are only supported in generic DT-only ARM multi-platform builds. The driver doesn't need to use platform data anymore, hence remove platform data configuration. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Tested-by: Niklas Söderlund <niso@kth.se> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Jun Nie authored
Add ZTE zx296702 GPIO controller support Signed-off-by: Jun Nie <jun.nie@linaro.org> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Jun Nie authored
Add document of ZTE zx296702 GPIO binding Signed-off-by: Jun Nie <jun.nie@linaro.org> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 15 Jul, 2015 9 commits
-
-
Masahiro Yamada authored
The variable "desc" is only used for storing the return value at the end of the function. It is unneeded. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
The driver gpio-mvebu.c does not depend on gpio-generic.c at all. Drop unneeded "select GPIO_GENERIC". Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
This driver calls of_mm_gpiochip_add() to add a memory mapped gpio chip. So, of_mm_gpiochip_remove() should be used when removing it. The direct call of gpiochip_remove() misses unmapping the register and freeing the label. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Tien Hock Loh <thloh@altera.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
The remove callback never succeeds, which seems odd. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Tien Hock Loh <thloh@altera.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
The driver gpio-altera.c does not depend on gpio-generic.c at all. Drop unneeded "select GPIO_GENERIC". Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Tien Hock Loh <thloh@altera.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Masahiro Yamada authored
This driver is tristate, so it should be cleanable. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Gregory Fong authored
Some brcmstb GPIO controllers can be used to wake from suspend, so use the de facto standard property 'wakeup-source' to mark the nodes of controllers with that capability. Also document interrupts-extended, which will be used for wakeup handling because the interrupt parent for the wake IRQ is different from the regular IRQ. While we're at it, a few more fixes: We don't actually use the "interrupt-names" property, so remove it from the listed optional properties and from the examples. And since we're modifying the examples, also follow Brian's suggestions to: - change #gpio-cells, #interrupt-cells, and brcm,gpio-bank-widths from hex to dec - use phandles Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Tomeu Vizoso authored
gpiochip_add_pingroup_range() has a pctldev argument, not pinctrl. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
Philipp Zabel authored
Allow to determine the current direction configuration by reading back from the direction register. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-
- 14 Jul, 2015 9 commits
-
-
Thomas Gleixner authored
Fix a race where a pending interrupt could be received and the handler called before the handler's data has been setup, by converting to irq_set_chained_handler_and_data(). Search and conversion was done with coccinelle. Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com>
-
Thomas Gleixner authored
It's pretty silly to do void *cd = irq_get_chip_data(irq_data->irq); because that results in cd = irq_data->chip_data, but goes through a redundant lookup of the irq_data. Use irq_data directly. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: linux-gpio@vger.kernel.org
-
Thomas Gleixner authored
It's pretty silly to do irq_data *d = irq_get_irq_data(irq_data->irq); because that results in d = irq_data, but goes through a lookup of the irq_data. Use irq_data directly. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: linux-gpio@vger.kernel.org
-
Thomas Gleixner authored
The irq argument of most interrupt flow handlers is unused or merily used instead of a local variable. The handlers which need the irq argument can retrieve the irq number from the irq descriptor. Search and update was done with coccinelle and the invaluable help of Julia Lawall. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org
-
Thomas Gleixner authored
The irq argument of most interrupt flow handlers is unused or merily used instead of a local variable. The handlers which need the irq argument can retrieve the irq number from the irq descriptor. Search and update was done with coccinelle and the invaluable help of Julia Lawall. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org
-
Thomas Gleixner authored
The irq argument of most interrupt flow handlers is unused or merily used instead of a local variable. The handlers which need the irq argument can retrieve the irq number from the irq descriptor. Search and update was done with coccinelle and the invaluable help of Julia Lawall. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org
-
Thomas Gleixner authored
The irq argument of most interrupt flow handlers is unused or merily used instead of a local variable. The handlers which need the irq argument can retrieve the irq number from the irq descriptor. Search and update was done with coccinelle and the invaluable help of Julia Lawall. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org
-
Jiang Liu authored
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we already have a pointer to corresponding irq_desc. Preparatory patch for the removal of the 'irq' argument from irq flow handlers. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
-
Jiang Liu authored
This is a preparatory patch for moving irq_data struct members. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
-