Fixed odd function behavior when dev->bus_id does not contain '.' - it
compared that case 0 characters of the string and hereby reported success and
executed callback. Now bus_id's are compared correctly, extra callback
triggering eliminated.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Fix __initcall return in proc_rtas_init and rtas_init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Since external and decrementer interrupts set the runlatch on, we need
to ensure its set off again in the idle loop. At the moment we dont turn
it off in the inner loop.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The patch removing _machine and converting platforms over to use
define_machine wasn't complete as far as CHRP was concerned.  This
adds the define_machine call for CHRP and gets it booting again.
Signed-off-by: Paul Mackerras <paulus@samba.org>

The iSeries Hypervisor only allows us to specify IRQ numbers up to 255 (it
has a u8 field to pass it in).  This patch allows platforms to specify a
maximum to the virtual IRQ numbers we will use and has iSeries set that
to 255.  If not set, the maximum is NR_IRQS - 1 (as before).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>

Close of the merge window..

Apparently nobody had tried to compile the ALSA CVS tree without power
management enabled.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
  [PATCH] splice: fix page stealing LRU handling.
  [PATCH] splice: page stealing needs to wait_on_page_writeback()
  [PATCH] splice: export generic_splice_sendpage
  [PATCH] splice: add a SPLICE_F_MORE flag
  [PATCH] splice: add comments documenting more of the code
  [PATCH] splice: improve writeback and clean up page stealing
  [PATCH] splice: fix shadow[] filling logic

Originally from Nick Piggin, just adapted to the newer branch.

You can't check PageLRU without holding zone->lru_lock.  The page
release code can get away with it only because the page refcount is 0 at
that point. Also, you can't reliably remove pages from the LRU unless
the refcount is 0. Ever.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Jens Axboe <axboe@suse.de>

Thanks to Andrew for the good explanation of why this is so. akpm writes:

If a page is under writeback and we remove it from pagecache, it's still
going to get written to disk.  But the VFS no longer knows about that page,
nor that this page is about to modify disk blocks.

So there might be scenarios in which those
blocks-which-are-about-to-be-written-to get reused for something else.
When writeback completes, it'll scribble on those blocks.

This won't happen in ext2/ext3-style filesystems in normal mode because the
page has buffers and try_to_release_page() will fail.

But ext2 in nobh mode doesn't attach buffers at all - it just sticks the
page in a BIO, finds some new blocks, points the BIO at those blocks and
lets it rip.

While that write IO's in flight, someone could truncate the file.  Truncate
won't block on the writeout because the page isn't in pagecache any more.
So truncate will the free the blocks from the file under the page's feet.
Then something else can reallocate those blocks.  Then write data to them.

Now, the original write completes, corrupting the filesystem.
Signed-off-by: Jens Axboe <axboe@suse.de>

Forgot that one, thanks Jeff. Also move the other EXPORT_SYMBOL
to right below the functions.
Signed-off-by: Jens Axboe <axboe@suse.de>

This lets userspace indicate whether more data will be coming in a
subsequent splice call.
Signed-off-by: Jens Axboe <axboe@suse.de>

Hopefully this will make Andrew a little more happy.
Signed-off-by: Jens Axboe <axboe@suse.de>

By cleaning up the writeback logic (killing write_one_page() and the manual
set_page_dirty()), we can get rid of ->stolen inside the pipe_buffer and
just keep it local in pipe_to_file().

This also adds dirty page balancing logic and O_SYNC handling.
Signed-off-by: Jens Axboe <axboe@suse.de>

Clear the entire range, and don't increment pidx or we keep filling
the same position again and again.

Thanks to KAMEZAWA Hiroyuki.
Signed-off-by: Jens Axboe <axboe@suse.de>

* master.kernel.org:/home/rmk/linux-2.6-arm: (27 commits)
  [ARM] 3433/1: ARM: OMAP: 8/8 Update board files
  [ARM] 3455/1: ARM: OMAP: 7/8 Misc updates, take 2
  [ARM] 3454/1: ARM: OMAP: 6/8 Update framebuffer low-level init code, take 2
  [ARM] 3430/1: ARM: OMAP: 5/8 Update PM
  [ARM] 3429/1: ARM: OMAP: 4/8 Update GPIO
  [ARM] 3428/1: ARM: OMAP: 3/8 Update pin multiplexing
  [ARM] 3427/1: ARM: OMAP: 2/8 Update timers
  [ARM] 3426/1: ARM: OMAP: 1/8 Update clock framework
  [ARM] 3396/2: AT91RM9200 Platform devices update
  [ARM] 3395/2: AT91RM9200 Dataflash Card vs MMC selection
  [ARM] 3393/2: AT91RM9200 LED support
  [ARM] 3453/1: Poodle: Correctly set the memory size
  [ARM] 3446/1: i.MX: MMC/SD SDHC controller registration for i.MX/MX1 MX1ADS board
  [ARM] 3444/1: i.MX: Scatter-gather DMA emulation for i.MX/MX1
  [ARM] 3451/1: ep93xx: use the m48t86 rtc driver on the ts72xx platform
  [ARM] 3450/1: ep93xx: use the ep93xx rtc driver
  [ARM] 3452/1: [S3C2410] RX3715 - add nand information
  [ARM] 3449/1: [S3C2410] Anubis - fix NAND timings
  [ARM] 3448/1: [S3C2410] Settle delay when _enabling_ USB PLL
  [ARM] 3442/1: [S3C2410] SMDK: NAND device setup
  ...

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [ARM] 3457/1: i.MX: SD/MMC support for i.MX/MX1
  [ARM] 3456/1: AT91RM9200 support for 2.6 (MMC/SD driver)

* git://oss.sgi.com:8090/oss/git/xfs-2.6:
  [XFS] Provide XFS support for the splice syscall.
  [XFS] Reenable write barriers by default.
  [XFS] Make project quota enforcement return an error code consistent with
  [XFS] Implement the silent parameter to fill_super, previously ignored.
  [XFS] Cleanup comment to remove reference to obsoleted function

* master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (28 commits)
  [ALSA] Kconfig SND_SEQUENCER_OSS help text fix
  [ALSA] Add Aux input switch control for Aureon Universe
  [ALSA] pcxhr - Fix the crash with REV01 board
  [ALSA] sound/pci/hda: use create_singlethread_workqueue()
  [ALSA] hda-intel - Add support of ATI SB600
  [ALSA] cs4281 - Fix the check of timeout in probe
  [ALSA] cs4281 - Fix the check of right channel
  [ALSA] Test volume resolution of usb audio at initialization
  [ALSA] maestro3.c: fix BUG, optimization
  [ALSA] HDA/Realtek: multiple input mux definitions and pin mode additions
  [ALSA] AdLib FM card driver
  [ALSA] Fix / clean up PCM-OSS setup hooks
  [ALSA] Clean up PCM codes (take 2)
  [ALSA] Tiny clean up of PCM codes
  [ALSA] ISA drivers bailing on first !enable[i]
  [ALSA] Remove obsolete kfree_nocheck call
  [ALSA] Remove obsolete kfree_nocheck call
  [ALSA] Add snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
  [ALSA] Add snd-riptide driver for Conexant Riptide chip
  [ALSA] hda-codec - Fix noisy output wtih AD1986A 3stack model
  ...

No one should be writing a PAGE_SIZE worth of data to a normal sysfs
file, so properly terminate the buffer.

Thanks to Al Viro for pointing out my supidity here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This reverts the mutex conversion that was recently done to the hdaps
driver; this coversion was buggy because the hdaps driver started using
this semaphore in IRQ context, which mutexes do not allow.  Easiest
solution for now is to just revert the patch (the patch was part of a
bigger GIT commit, 9a61bf63 but this
only reverts this one file)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] at91_wdt.c - Atmel AT91RM9200 watchdog driver
  [WATCHDOG] pcwd_usb.c: fix a NULL pointer dereference
  [WATCHDOG] pcwd.c sprintf/strcpy fix
  [WATCHDOG] pcwd.c general clean-up after patches
  [WATCHDOG] pcwd.c add debug info
  [WATCHDOG] pcwd.c pcwd_cleanup_module patch
  [WATCHDOG] pcwd.c firmware-info patch
  [WATCHDOG] pcwd.c control status patch

* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
  Documentation: fix minor kernel-doc warnings
  BUG_ON() Conversion in drivers/net/
  BUG_ON() Conversion in drivers/s390/net/lcs.c
  BUG_ON() Conversion in mm/slab.c
  BUG_ON() Conversion in mm/highmem.c
  BUG_ON() Conversion in kernel/signal.c
  BUG_ON() Conversion in kernel/signal.c
  BUG_ON() Conversion in kernel/ptrace.c
  BUG_ON() Conversion in ipc/shm.c
  BUG_ON() Conversion in fs/freevxfs/
  BUG_ON() Conversion in fs/udf/
  BUG_ON() Conversion in fs/sysv/
  BUG_ON() Conversion in fs/inode.c
  BUG_ON() Conversion in fs/fcntl.c
  BUG_ON() Conversion in fs/dquot.c
  BUG_ON() Conversion in md/raid10.c
  BUG_ON() Conversion in md/raid6main.c
  BUG_ON() Conversion in md/raid5.c
  Fix minor documentation typo
  BFP->BPF in Documentation/networking/tuntap.txt
  ...

sbp2util_mark_command_completed takes a lock which was already taken by
sbp2scsi_complete_all_commands.  This is a regression in Linux 2.6.15.

 Reported by Kristian Harms at
	https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187394

[ More complete commentary, as response to questions by Andrew: ]

> This changes the call environment for all implementations of
> ->Current_done().  Are they all safe to call under this lock?

Short answer: Yes, trust me.  ;-) Long answer:

The done() callbacks are passed on to sbp2 from the SCSI stack along
with each SCSI command via the queuecommand hook.  The done() callback
is safe to call in atomic context.  So does
Documentation/scsi/scsi_mid_low_api.txt say, and many if not all SCSI
low-level handlers rely on this fact.  So whatever this callback does,
it is "self-contained" and it won't conflict with sbp2's internal ORB
list handling.  In particular, it won't race with the
sbp2_command_orb_lock.

Moreover, sbp2 already calls the done() handler with
sbp2_command_orb_lock taken in sbp2scsi_complete_all_commands().  I
admit this is ultimately no proof of correctness, especially since this
portion of code introduced the spinlock recursion in the first place and
we didn't realize it since this code's submission before 2.6.15 until
now.  (I have learned a lesson from this.)

I stress-tested my patch on x86 uniprocessor with a preemptible SMP
kernel (alas I have no SMP machine yet) and made sure that all code
paths which involve the sbp2_command_orb_lock were gone through multiple
times.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (49 commits)
  V4L/DVB (3667b): cpia2: fix function prototype
  V4L/DVB (3702): Make msp3400 routing defines more consistent
  V4L/DVB (3700): Remove obsolete commands from tvp5150.c
  V4L/DVB (3697): More msp3400 and bttv fixes
  V4L/DVB (3696): Previous change for cx2341X boards broke the remote support
  V4L/DVB (3693): Fix msp3400c and bttv stereo/mono/bilingual detection/handling
  V4L/DVB (3692): Keep experimental SLICED_VBI defines under an #if 0
  V4L/DVB (3689): Kconfig: fix VP-3054 Secondary I2C Bus build configuration menu dependencies
  V4L/DVB (3673): Fix budget-av CAM reset
  V4L/DVB (3672): Fix memory leak in dvr open
  V4L/DVB (3671): New module parameter 'tv_standard' (dvb-ttpci driver)
  V4L/DVB (3670): Fix typo in comment
  V4L/DVB (3669): Configurable dma buffer size for saa7146-based budget dvb cards
  V4L/DVB (3653h): Move usb v4l docs into Documentation/video4linux
  V4L/DVB (3667a): Fix SAP + stereo mode at msp3400
  V4L/DVB (3666): Remove trailing newlines
  V4L/DVB (3665): Add new NEC uPD64031A and uPD64083 i2c drivers
  V4L/DVB (3663): Fix msp3400c wait time and better audio mode fallbacks
  V4L/DVB (3662): Don't set msp3400c-non-existent register
  V4L/DVB (3661): Add wm8739 stereo audio ADC i2c driver
  ...

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ipath: kbuild infrastructure
  IB/ipath: infiniband verbs support
  IB/ipath: misc infiniband code, part 2
  IB/ipath: misc infiniband code, part 1
  IB/ipath: infiniband RC protocol support
  IB/ipath: infiniband UC and UD protocol support
  IB/ipath: infiniband header files
  IB/ipath: layering interfaces used by higher-level driver code
  IB/ipath: support for userspace apps using core driver
  IB/ipath: sysfs and ipathfs support for core driver
  IB/ipath: misc driver support code
  IB/ipath: chip initialisation code, and diag support
  IB/ipath: support for PCI Express devices
  IB/ipath: support for HyperTransport devices
  IB/ipath: core driver header files
  IB/ipath: core device driver

* master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (33 commits)
  [PATCH] pcmcia: declare pccard_iodyn_ops (fix m8xx_pcmcia.c compilation error)
  [PATCH] pcmcia: fix pcmcia_device_remove oops
  [PATCH] pcmcia: Add support for Possio GCC AKA PCMCIA Siemens MC45
  [PATCH] pcmcia: pseudo device handling update
  [PATCH] pcmcia: convert DEV_OK to pcmcia_dev_present
  [PATCH] pcmcia: use bitfield instead of p_state and state
  [PATCH] pcmcia: remove unused p_dev->state flags
  [PATCH] pcmcia: make pcmcia_release_{io,irq} static
  [PATCH] pcmcia: add return value to _config() functions
  [PATCH] pcmcia: remove dev_link_t and client_handle_t indirection
  [PATCH] pcmcia: embed dev_link_t into struct pcmcia_device
  [PATCH] pcmcia: rename pcmcia_device.state
  [PATCH] pcmcia: remove unneeded Vcc pseudo setting
  [PATCH] pcmcia: remove export of pcmcia_release_configuration
  [PATCH] pcmcia: default suspend and resume handling
  [PATCH] pcmcia: convert remaining users of pcmcia_release_io and _irq
  [PATCH] pcmcia: add pcmcia_disable_device
  [PATCH] serial_cs: add Merlin U630 IDs
  [PATCH] pcmcia: AT91RM9200 Compact Flash driver
  [PATCH] pcmcia: socket.functions starts with 1
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (26 commits)
  Input: add support for Braille devices
  Input: synaptics - limit rate to 40pps on Toshiba Protege M300
  Input: gamecon - add SNES mouse support
  Input: make modalias code respect allowed buffer size
  Input: convert /proc handling to seq_file
  Input: limit attributes' output to PAGE_SIZE
  Input: gameport - fix memory leak
  Input: serio - fix memory leak
  Input: zaurus keyboard driver updates
  Input: i8042 - fix logic around pnp_register_driver()
  Input: ns558 - fix logic around pnp_register_driver()
  Input: pcspkr - separate device and driver registration
  Input: atkbd - allow disabling on X86_PC (if EMBEDDED)
  Input: atkbd - disable softrepeat for dumb keyboards
  Input: atkbd - fix complaints about 'releasing unknown key 0x7f'
  Input: HID - fix duplicate key mapping for Logitech UltraX remote
  Input: use kzalloc() throughout the code
  Input: fix input_free_device() implementation
  Input: initialize serio and gameport at subsystem level
  Input: uinput - semaphore to mutex conversion
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
  [PATCH] powerpc: iSeries needs slb_initialize to be called
  powerpc: hook up the splice syscall
  [PATCH] powerpc/cell: compile fixes
  [PATCH] powerpc: trivial spelling fixes in fault.c
  [PATCH] powerpc/pseries: EEH Cleanup
  [PATCH] powerpc/pseries: misc lparcfg fixes
  [PATCH] powerpc/pseries: fix device name printing, again.
  [PATCH] powerpc: Extends HCALL interface for InfiniBand usage
  [PATCH] powerpc/pseries: Change H_StudlyCaps to H_SHOUTING_CAPS
  [PATCH] powerpc/pseries: print message if EEH recovery fails
  [PATCH] powerpc/pseries: mutex lock to serialize EEH event processing
  powerpc: converted embedded platforms to use new define_machine support
  powerpc: merge machine_check_exception between ppc32 & ppc64

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC]: Wire up sys_sync_file_range() into syscall tables.
  [SPARC]: Wire up sys_splice() into the syscall tables.
  [SPARC64]: Update defconfig.
  [SPARC64]: Align address in huge_pte_alloc().
  [SPARC64]: Document the instruction checks we do in do_sparc64_fault().
  [SPARC64]: Make tsb_sync() mm comparison more precise.

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: Fully fix the memory leaks in sys_accept().
  [NETFILTER]: iptables 32bit compat layer
  [NETFILTER]: {ip,nf}_conntrack_netlink: fix expectation notifier unregistration
  [NETFILTER]: fix ifdef for connmark support in nf_conntrack_netlink
  [NETFILTER]: x_tables: unify IPv4/IPv6 multiport match
  [NETFILTER]: x_tables: unify IPv4/IPv6 esp match
  [NET]: Fix dentry leak in sys_accept().
  [IPSEC]: Kill unused decap state structure
  [IPSEC]: Kill unused decap state argument
  [NET]: com90xx kmalloc fix
  [TG3]: Update driver version and reldate.
  [TG3]: Revert "Speed up SRAM access"

It doesn't make the splice itself necessarily nonblocking (because the
actual file descriptors that are spliced from/to may block unless they
have the O_NONBLOCK flag set), but it makes the splice pipe operations
nonblocking.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Patch from Pavel Pisa

This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.

There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.

Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds support for the MMC/SD card interface on the Atmel
AT91RM9200 processor.

Original driver was by Nick Randell, but a number of people have
subsequently worked on it. It's currently maintained by Malcolm Noyes.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

(We'd only added the number, which meant that actually trying
to use splice just went off into la-la-land)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Watchdog driver for the Atmel AT91RM9200 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>

The Coverity checker noted that this resulted in a NULL pointer
reference if we were coming from

        if (usb_pcwd == NULL) {
                printk(KERN_ERR PFX "Out of memory\n");
                    goto error;
        }
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>

change sprintf(pcwd_private.fw_ver_str, "ERROR");
to strcpy... as pointed out by Andrew Morton.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>

removal of includes (since we don't use kmalloc and
TASK_INTERRUPTABLE anymore).
Addition of missing commands.
Printk that lets the user know when the module was
unloaded.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Add debugging info for the pcwd.c module.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>