Even though the taprio qdisc is designed for multiqueue devices, all the
queues still point to the same top-level taprio qdisc. This works and is
probably required for software taprio, but at least with offload taprio,
it has an undesirable side effect: because the whole qdisc is run when a
packet has to be sent, it allows packets in a best-effort class to be
processed in the context of a task sending higher priority traffic. If
there are packets left in the qdisc after that first run, the NET_TX
softirq is raised and gets executed immediately in the same process
context. As with any other softirq, it runs up to 10 times and for up to
2ms, during which the calling process is waiting for the sendmsg call (or
similar) to return. In my use case, that calling process is a real-time
task scheduled to send a packet every 2ms, so the long sendmsg calls are
leading to missed timeslots.

By attaching each netdev queue to its own qdisc, as it is done with
the "classic" mq qdisc, each traffic class can be processed independently
without touching the other classes. A high-priority process can then send
packets without getting stuck in the sendmsg call anymore.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function tls_sw_splice_read, before call tls_sw_advance_skb
it checks likely(!(flags & MSG_PEEK)), while MSG_PEEK is used
for recvmsg, splice supports SPLICE_F_NONBLOCK, SPLICE_F_MOVE,
SPLICE_F_MORE, should remove this checking.
Signed-off-by: Jim Ma <majinjing3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.

Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rcu_head pointer passed to taprio_free_sched_cb is never NULL.
That means that the result of container_of() operations on it is also
never NULL, even though rcu_head is the first element of the structure
embedding it. On top of that, it is misleading to perform a NULL check
on the result of container_of() because the position of the contained
element could change, which would make the check invalid. Remove the
unnecessary NULL check.

This change was made automatically with the following Coccinelle script.

@@
type t;
identifier v;
statement s;
@@

<+...
(
  t v = container_of(...);
|
  v = container_of(...);
)
  ...
  when != v
- if (\( !v \| v == NULL \) ) s
...+>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The WWAN framework provides a unified way to handle WWAN/modems and its
control port(s). It has initially been introduced to support MHI/PCI
modems, offering the same control protocols as the USB variants such as
MBIM, QMI, AT... The WWAN framework exposes these control protocols as
character devices, similarly to cdc-wdm, but in a bus agnostic fashion.

This change adds registration of the USB modem cdc-wdm control endpoints
to the WWAN framework as standard control ports (wwanXpY...).

Exposing cdc-wdm through WWAN framework normally maintains backward
compatibility, e.g:
    $ qmicli --device-open-qmi -d /dev/wwan0p1QMI --dms-get-ids
instead of
    $ qmicli --device-open-qmi -d /dev/cdc-wdm0 --dms-get-ids

However, some tools may rely on cdc-wdm driver/device name for device
detection. It is then safer to keep the 'legacy' cdc-wdm character
device to prevent any breakage. This is handled in this change by
API mutual exclusion, only one access method can be used at a time,
either cdc-wdm chardev or WWAN API.

Note that unknown channel types (other than MBIM, AT or MBIM) are not
registered to the WWAN framework.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some devices may have ports with unknown type/protocol which need to
be tagged (though not supported by WWAN core). This will be the case
for cdc-wdm based drivers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.

Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.

Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matteo Croce says:

====================
mvpp2: resolve two warnings

Just two small changes to suppress two warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove some unreachable code, so to suppress this warning:

drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c: In function ‘mvpp2_prs_tcam_first_free’:
drivers/net/ethernet/marvell/mvpp2/mvpp2_prs.c:397:10: warning: comparison is always false due to limited range of data type [-Wtype-limits]
  397 |  if (end >= MVPP2_PRS_TCAM_SRAM_SIZE)
      |          ^~

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mvpp2_run_xdp() has an unused parameter rxq, remove it.

Fixes: 07dd0a7a ("mvpp2: add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Shevchenko says:

====================
net: pch_gbe: fix and a few cleanups

The series provides one fix (patch 1) for GPIO to be able to wait for
the GPIO driver to appear. This is separated from the conversion to
the GPIO descriptors (patch 2) in order to have a possibility for
backporting. Patches 3 and 4 fix minor warnings from Sparse while
moving to a new APIs. Patch 5 is MODULE_VERSION() clean up.

Tested on Intel Minnowboard (v1).

Since v3:
- rebased on top of v5.13-rc1
- added Tested-by (Flavio)
- added Reported-by to certain changes (LKP)

Since v2:
- added a few cleanups on top of the fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove MODULE_VERSION(), as it doesn't seem to serve any practical purpose.
For in-tree drivers, the kernel version matters. The code received lots of
changes, but module version remained constant, since the driver landed in
mainline. So, this version doesn't seem have any practical meaning anymore.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse is not happy about handling of strict types in pch_ptp_match():

  .../pch_gbe_main.c:158:33: warning: incorrect type in argument 2 (different base types)
  .../pch_gbe_main.c:158:33:    expected unsigned short [usertype] uid_hi
  .../pch_gbe_main.c:158:33:    got restricted __be16 [usertype]
  .../pch_gbe_main.c:158:45: warning: incorrect type in argument 3 (different base types)
  .../pch_gbe_main.c:158:45:    expected unsigned int [usertype] uid_lo
  .../pch_gbe_main.c:158:45:    got restricted __be32 [usertype]
  .../pch_gbe_main.c:158:56: warning: incorrect type in argument 4 (different base types)
  .../pch_gbe_main.c:158:56:    expected unsigned short [usertype] seqid
  .../pch_gbe_main.c:158:56:    got restricted __be16 [usertype]

Fix that by switching to use proper accessors to BE data.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use readx_poll_timeout_atomic() instead of open coded variants.

While at it, add __iomem attribute to the parameter of pch_gbe_wait_clr_bit().
This in particular will fix a lot of warnings detected by Sparse, e.g.

.../pch_gbe_main.c:308:26: warning: incorrect type in argument 1 (different address spaces)
.../pch_gbe_main.c:308:26:    expected void const [noderef] __iomem *
.../pch_gbe_main.c:308:26:    got void *reg
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

This switches the PCH GBE driver to use GPIO descriptors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

If GPIO controller is not available yet we need to defer
the probe of GBE until provider will become available.

While here, drop GPIOF_EXPORT because it's deprecated and
may not be available.

Fixes: f1a26fdf ("pch_gbe: Add MinnowBoard support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>

Radu Pirea says:

====================
Add PTP support for TJA1103

This is the PTP support for TJA1103.
The RX timestamp is found in the reserved2 field of the PTP package.
The TX timestamp has to be read from the phy registers. Reading of the
timestamp works with interrupts or with polling(that starts when
.nxp_c45_txtstamp is called).
The implementation of .adjtime is done by read modify write because there
is no way to atomically add/subtract a constant from the clock value.

I've moved scaled_ppm_to_ppb function from ptp_clock.c to
ptp_clock_kernel.h in  order to be able to build the driver without
PTP_1588_CLOCK=y.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mii_timestamper interface and register a ptp clock.
The package timestamping can work with or without interrupts.
RX timestamps are received in the reserved field of the PTP package.
TX timestamps are read via MDIO from a set of registers.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make scaled_ppm_to_ppb static inline to be able to build drivers that
use this function even with PTP_1588_CLOCK disabled.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Custom isprint() definition may collide with one form ctype.h.
In order to avoid this, replace it with a functional analogue
which is isascii() && isprint() in this case.

First appearance of the code is in the commit 636b3843
("Import 2.3.43").
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The statement of the last "if (xxx)" branch is the same as the "else"
branch. Delete it to simplify code.

No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

device_property_read_u32() may return different error codes.
Propagate it to the caller.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace open coded variants of devm_clk_get_optional().
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In each iteration fwnode_for_each_available_child_node() bumps a reference
counting of a loop variable followed by dropping in on a next iteration,

Since in error case the loop is broken, we have to drop a reference count
by ourselves. Do it for port_fwnode in error case during ->probe().

Fixes: 24812221 ("net: mvpp2: use device_*/fwnode_* APIs instead of of_*")
Cc: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we call af_ops->set_link_af() we hold a RCU read lock
as we retrieve af_ops from the RCU protected list, but this
is unnecessary because we already hold RTNL lock, which is
the writer lock for protecting rtnl_af_ops, so it is safer
than RCU read lock. Similar for af_ops->validate_link_af().

This was not a problem until we begin to take mutex lock
down the path of ->set_link_af() in __ipv6_dev_mc_dec()
recently. We can just drop the RCU read lock there and
assert RTNL lock.

Reported-and-tested-by: syzbot+7d941e89dd48bcf42573@syzkaller.appspotmail.com
Fixes: 63ed8de4 ("mld: add mc_lock for protecting per-interface mld data")
Tested-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefan Wahren says:

====================
net: qca_spi: Improve sync handling

This small patch series contains some improvements of the sync
handling. This was discovered while the QCA7000 was doing SLAC
(Signal Level Attenuation Characterization).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to identify significant signature issues add a new stat counter,
which increases on bad signature values that causes a sync loss.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting a new network key would cause a reset of the QCA7000. Usually
the driver only notice the SPI interrupt and a single signature error.
So avoid the whole re-sync process (possible packet loss, transmit queue
stop and no carrier for at least 1 second) in this case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to read the signature three times. So bail out
in case the second check failed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Integer variable 'bucket' is being initialized however
this value is never read as 'bucket' is assigned zero
in for statement. Remove the redundant assignment.

Cleans up clang warning:

net/core/neighbour.c:3144:6: warning: Value stored to 'bucket' during
its initialization is never read [clang-analyzer-deadcode.DeadStores]
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need add 'if (skb_nfct(skb))' assignment, the
nf_conntrack_put() would check it.
Signed-off-by: Yejune Deng <yejunedeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull RISC-V fixes from Palmer Dabbelt:

 - A fix to avoid over-allocating the kernel's mapping on !MMU systems,
   which could lead to up to 2MiB of lost memory

 - The SiFive address extension errata only manifest on rv64, they are
   now disabled on rv32 where they are unnecessary

 - A pair of late-landing cleanups

* tag 'riscv-for-linus-5.13-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: remove unused handle_exception symbol
  riscv: Consistify protect_kernel_linear_mapping_text_rodata() use
  riscv: enable SiFive errata CIP-453 and CIP-1200 Kconfig only if CONFIG_64BIT=y
  riscv: Only extend kernel reservation if mapped read-only

intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().

End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer.  gcc-11 correctly warns
about this case:

  drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
  drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
   3491 |                     !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
        |                      ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
  In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
  include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
   1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
        |      ^~~~~~~~~~~~~~~~~~~~
       6:14 elapsed

This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.

There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more SCSI updates from James Bottomley:
 "This is a set of minor fixes in various drivers (qla2xxx, ufs,
  scsi_debug, lpfc) one doc fix and a fairly large update to the fnic
  driver to remove the open coded iteration functions in favour of the
  scsi provided ones"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: fnic: Use scsi_host_busy_iter() to traverse commands
  scsi: fnic: Kill 'exclude_id' argument to fnic_cleanup_io()
  scsi: scsi_debug: Fix cmd_per_lun, set to max_queue
  scsi: ufs: core: Narrow down fast path in system suspend path
  scsi: ufs: core: Cancel rpm_dev_flush_recheck_work during system suspend
  scsi: ufs: core: Do not put UFS power into LPM if link is broken
  scsi: qla2xxx: Prevent PRLI in target mode
  scsi: qla2xxx: Add marginal path handling support
  scsi: target: tcmu: Return from tcmu_handle_completions() if cmd_id not found
  scsi: ufs: core: Fix a typo in ufs-sysfs.c
  scsi: lpfc: Fix bad memory access during VPD DUMP mailbox command
  scsi: lpfc: Fix DMA virtual address ptr assignment in bsg
  scsi: lpfc: Fix illegal memory access on Abort IOCBs
  scsi: blk-mq: Fix build warning when making htmldocs

Pull more Kbuild updates from Masahiro Yamada:

 - Convert sh and sparc to use generic shell scripts to generate the
   syscall headers

 - refactor .gitignore files

 - Update kernel/config_data.gz only when the content of the .config
   is really changed, which avoids the unneeded re-link of vmlinux

 - move "remove stale files" workarounds to scripts/remove-stale-files

 - suppress unused-but-set-variable warnings by default for Clang
   as well

 - fix locale setting LANG=C to LC_ALL=C

 - improve 'make distclean'

 - always keep intermediate objects from scripts/link-vmlinux.sh

 - move IF_ENABLED out of <linux/kconfig.h> to make it self-contained

 - misc cleanups

* tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
  linux/kconfig.h: replace IF_ENABLED() with PTR_IF() in <linux/kernel.h>
  kbuild: Don't remove link-vmlinux temporary files on exit/signal
  kbuild: remove the unneeded comments for external module builds
  kbuild: make distclean remove tag files in sub-directories
  kbuild: make distclean work against $(objtree) instead of $(srctree)
  kbuild: refactor modname-multi by using suffix-search
  kbuild: refactor fdtoverlay rule
  kbuild: parameterize the .o part of suffix-search
  arch: use cross_compiling to check whether it is a cross build or not
  kbuild: remove ARCH=sh64 support from top Makefile
  .gitignore: prefix local generated files with a slash
  kbuild: replace LANG=C with LC_ALL=C
  Makefile: Move -Wno-unused-but-set-variable out of GCC only block
  kbuild: add a script to remove stale generated files
  kbuild: update config_data.gz only when the content of .config is changed
  .gitignore: ignore only top-level modules.builtin
  .gitignore: move tags and TAGS close to other tag files
  kernel/.gitgnore: remove stale timeconst.h and hz.bc
  usr/include: refactor .gitignore
  genksyms: fix stale comment
  ...

Pull powerpc updates and fixes from Michael Ellerman:
 "A bit of a mixture of things, tying up some loose ends.

  There's the removal of the nvlink code, which dependend on a commit in
  the vfio tree. Then the enablement of huge vmalloc which was in next
  for a few weeks but got dropped due to conflicts. And there's also a
  few fixes.

  Summary:

   - Remove the nvlink support now that it's only user has been removed.

   - Enable huge vmalloc mappings for Radix MMU (P9).

   - Fix KVM conversion to gfn-based MMU notifier callbacks.

   - Fix a kexec/kdump crash with hot plugged CPUs.

   - Fix boot failure on 32-bit with CONFIG_STACKPROTECTOR.

   - Restore alphabetic order of the selects under CONFIG_PPC.

  Thanks to: Christophe Leroy, Christoph Hellwig, Nicholas Piggin,
  Sandipan Das, and Sourabh Jain"

* tag 'powerpc-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  KVM: PPC: Book3S HV: Fix conversion to gfn-based MMU notifier callbacks
  powerpc/kconfig: Restore alphabetic order of the selects under CONFIG_PPC
  powerpc/32: Fix boot failure with CONFIG_STACKPROTECTOR
  powerpc/powernv/memtrace: Fix dcache flushing
  powerpc/kexec_file: Use current CPU info while setting up FDT
  powerpc/64s/radix: Enable huge vmalloc mappings
  powerpc/powernv: remove the nvlink support

Pull networking fixes from Jakub Kicinski:
 "Networking fixes for 5.13-rc1, including fixes from bpf, can and
  netfilter trees. Self-contained fixes, nothing risky.

  Current release - new code bugs:

   - dsa: ksz: fix a few bugs found by static-checker in the new driver

   - stmmac: fix frame preemption handshake not triggering after
     interface restart

  Previous releases - regressions:

   - make nla_strcmp handle more then one trailing null character

   - fix stack OOB reads while fragmenting IPv4 packets in openvswitch
     and net/sched

   - sctp: do asoc update earlier in sctp_sf_do_dupcook_a

   - sctp: delay auto_asconf init until binding the first addr

   - stmmac: clear receive all(RA) bit when promiscuous mode is off

   - can: mcp251x: fix resume from sleep before interface was brought up

  Previous releases - always broken:

   - bpf: fix leakage of uninitialized bpf stack under speculation

   - bpf: fix masking negation logic upon negative dst register

   - netfilter: don't assume that skb_header_pointer() will never fail

   - only allow init netns to set default tcp cong to a restricted algo

   - xsk: fix xp_aligned_validate_desc() when len == chunk_size to avoid
     false positive errors

   - ethtool: fix missing NLM_F_MULTI flag when dumping

   - can: m_can: m_can_tx_work_queue(): fix tx_skb race condition

   - sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b

   - bridge: fix NULL-deref caused by a races between assigning
     rx_handler_data and setting the IFF_BRIDGE_PORT bit

  Latecomer:

   - seg6: add counters support for SRv6 Behaviors"

* tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits)
  atm: firestream: Use fallthrough pseudo-keyword
  net: stmmac: Do not enable RX FIFO overflow interrupts
  mptcp: fix splat when closing unaccepted socket
  i40e: Remove LLDP frame filters
  i40e: Fix PHY type identifiers for 2.5G and 5G adapters
  i40e: fix the restart auto-negotiation after FEC modified
  i40e: Fix use-after-free in i40e_client_subtask()
  i40e: fix broken XDP support
  netfilter: nftables: avoid potential overflows on 32bit arches
  netfilter: nftables: avoid overflows in nft_hash_buckets()
  tcp: Specify cmsgbuf is user pointer for receive zerocopy.
  mlxsw: spectrum_mr: Update egress RIF list before route's action
  net: ipa: fix inter-EE IRQ register definitions
  can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
  can: mcp251x: fix resume from sleep before interface was brought up
  can: mcp251xfd: mcp251xfd_probe(): add missing can_rx_offload_del() in error path
  can: mcp251xfd: mcp251xfd_probe(): fix an error pointer dereference in probe
  netfilter: nftables: Fix a memleak from userdata error path in new objects
  netfilter: remove BUG_ON() after skb_header_pointer()
  netfilter: nfnetlink_osf: Fix a missing skb_header_pointer() NULL check
  ...

<linux/kconfig.h> is included from all the kernel-space source files,
including C, assembly, linker scripts. It is intended to contain a
minimal set of macros to evaluate CONFIG options.

IF_ENABLED() is an intruder here because (x ? y : z) is C code, which
should not be included from assembly files or linker scripts.

Also, <linux/kconfig.h> is no longer self-contained because NULL is
defined in <linux/stddef.h>.

Move IF_ENABLED() out to <linux/kernel.h> as PTR_IF(). PTF_IF()
takes the general boolean expression instead of a CONFIG option
so that it fits better in <linux/kernel.h>.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>