When a system is under memory presure (high usage with fragments),
the original 256KB ICM chunk allocations will likely trigger kernel
memory management to enter slow path doing memory compact/migration
ops in order to complete high order memory allocations.

When that happens, user processes calling uverb APIs may get stuck
for more than 120s easily even though there are a lot of free pages
in smaller chunks available in the system.

Syslog:
...
Dec 10 09:04:51 slcc03db02 kernel: [397078.572732] INFO: task
oracle_205573_e:205573 blocked for more than 120 seconds.
...

With 4KB ICM chunk size on x86_64 arch, the above issue is fixed.

However in order to support smaller ICM chunk size, we need to fix
another issue in large size kcalloc allocations.

E.g.
Setting log_num_mtt=30 requires 1G mtt entries. With the 4KB ICM chunk
size, each ICM chunk can only hold 512 mtt entries (8 bytes for each mtt
entry). So we need a 16MB allocation for a table->icm pointer array to
hold 2M pointers which can easily cause kcalloc to fail.

The solution is to use kvzalloc to replace kcalloc which will fall back
to vmalloc automatically if kmalloc fails.
Signed-off-by: Qing Huang <qing.huang@oracle.com>
Acked-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 624dbf55 ("driver/net: enic: Try DMA 64 first, then
failover to DMA") DMA mask was changed from 40 bits to 64 bits.
Hardware actually supports only 47 bits.

Fixes: 624dbf55 ("driver/net: enic: Try DMA 64 first, then failover to DMA")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PPPIOCDETACH ioctl effectively tries to "close" the given ppp file
before f_count has reached 0, which is fundamentally a bad idea.  It
does check 'f_count < 2', which excludes concurrent operations on the
file since they would only be possible with a shared fd table, in which
case each fdget() would take a file reference.  However, it fails to
account for the fact that even with 'f_count == 1' the file can still be
linked into epoll instances.  As reported by syzbot, this can trivially
be used to cause a use-after-free.

Yet, the only known user of PPPIOCDETACH is pppd versions older than
ppp-2.4.2, which was released almost 15 years ago (November 2003).
Also, PPPIOCDETACH apparently stopped working reliably at around the
same time, when the f_count check was added to the kernel, e.g. see
https://lkml.org/lkml/2002/12/31/83.  Also, the current 'f_count < 2'
check makes PPPIOCDETACH only work in single-threaded applications; it
always fails if called from a multithreaded application.

All pppd versions released in the last 15 years just close() the file
descriptor instead.

Therefore, instead of hacking around this bug by exporting epoll
internals to modules, and probably missing other related bugs, just
remove the PPPIOCDETACH ioctl and see if anyone actually notices.  Leave
a stub in place that prints a one-time warning and returns EINVAL.

Reported-by: syzbot+16363c99d4134717c05b@syzkaller.appspotmail.com
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

A precondition check in ip_recv_error triggered on an otherwise benign
race. Remove the warning.

The warning triggers when passing an ipv6 socket to this ipv4 error
handling function. RaceFuzzer was able to trigger it due to a race
in setsockopt IPV6_ADDRFORM.

  ---
  CPU0
    do_ipv6_setsockopt
      sk->sk_socket->ops = &inet_dgram_ops;

  ---
  CPU1
    sk->sk_prot->recvmsg
      udp_recvmsg
        ip_recv_error
          WARN_ON_ONCE(sk->sk_family == AF_INET6);

  ---
  CPU0
    do_ipv6_setsockopt
      sk->sk_family = PF_INET;

This socket option converts a v6 socket that is connected to a v4 peer
to an v4 socket. It updates the socket on the fly, changing fields in
sk as well as other structs. This is inherently non-atomic. It races
with the lockless udp_recvmsg path.

No other code makes an assumption that these fields are updated
atomically. It is benign here, too, as ip_recv_error cares only about
the protocol of the skbs enqueued on the error queue, for which
sk_family is not a precise predictor (thanks to another isue with
IPV6_ADDRFORM).

Link: http://lkml.kernel.org/r/20180518120826.GA19515@dragonet.kaist.ac.kr
Fixes: 7ce875e5 ("ipv4: warn once on passing AF_INET6 socket to ip_recv_error")
Reported-by: DaeRyong Jeong <threeearcat@gmail.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dealing with ingress rule on a netdev, if we did fine through the
conventional path, there's no need to continue into the egdev route,
and we can stop right there.

Not doing so may cause a 2nd rule to be added by the cls api layer
with the ingress being the egdev.

For example, under sriov switchdev scheme, a user rule of VFR A --> VFR B
will end up with two HW rules (1) VF A --> VF B and (2) uplink --> VF B

Fixes: 208c0f4b ('net: sched: use tc_setup_cb_call to call per-block callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DaeRyong Jeong reports a race between vhost_dev_cleanup() and
vhost_process_iotlb_msg():

Thread interleaving:
CPU0 (vhost_process_iotlb_msg)			CPU1 (vhost_dev_cleanup)
(In the case of both VHOST_IOTLB_UPDATE and
VHOST_IOTLB_INVALIDATE)

=====						=====
						vhost_umem_clean(dev->iotlb);
if (!dev->iotlb) {
	        ret = -EFAULT;
		        break;
}
						dev->iotlb = NULL;

The reason is we don't synchronize between them, fixing by protecting
vhost_process_iotlb_msg() with dev mutex.
Reported-by: DaeRyong Jeong <threeearcat@gmail.com>
Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2018-05-24

This series includes two mlx5 fixes.

1) add FCS data to checksum complete when required, from Eran Ben
Elisha.

2) Fix A race in IPSec sandbox QP commands, from Yossi Kuperman.

Please pull and let me know if there's any problem.

for -stable v4.15
("net/mlx5e: When RXFCS is set, add FCS data into checksum calculation")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b84bbaf7 ("packet: in packet_snd start writing at link
layer allocation") ensures that packet_snd always starts writing
the link layer header in reserved headroom allocated for this
purpose.

This is needed because packets may be shorter than hard_header_len,
in which case the space up to hard_header_len may be zeroed. But
that necessary padding is not accounted for in skb->len.

The fix, however, is buggy. It calls skb_push, which grows skb->len
when moving skb->data back. But in this case packet length should not
change.

Instead, call skb_reserve, which moves both skb->data and skb->tail
back, without changing length.

Fixes: b84bbaf7 ("packet: in packet_snd start writing at link layer allocation")
Reported-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sandbox QP Commands are retired in the order they are sent. Outstanding
commands are stored in a linked-list in the order they appear. Once a
response is received and the callback gets called, we pull the first
element off the pending list, assuming they correspond.

Sending a message and adding it to the pending list is not done atomically,
hence there is an opportunity for a race between concurrent requests.

Bind both send and add under a critical section.

Fixes: bebb23e6 ("net/mlx5: Accel, Add IPSec acceleration interface")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When RXFCS feature is enabled, the HW do not strip the FCS data,
however it is not present in the checksum calculated by the HW.

Fix that by manually calculating the FCS checksum and adding it to the SKB
checksum field.

Add helper function to find the FCS data for all SKB forms (linear,
one fragment or more).

Fixes: 102722fc ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.

This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):

[  154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[  154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G          I
[  154.675856] -----------------------------------------------------
[  154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[  154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[  154.700927]
and this task is already holding:
[  154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[  154.718028] which would create a new lock dependency:
[  154.723705]  (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[  154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[  154.740798]  (&(&cq->lock)->rlock){..-.}
[  154.740800]
... which became SOFTIRQ-irq-safe at:
[  154.752163]   _raw_spin_lock_irqsave+0x3e/0x50
[  154.757163]   mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[  154.762554]   ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[  154.815603]  (&(&qp_table->lock)->rlock){+.+.}
[  154.815604]
... which became SOFTIRQ-irq-unsafe at:
[  154.827718] ...
[  154.827720]   _raw_spin_lock+0x35/0x50
[  154.833912]   mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[  154.839302]   mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]

Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.

Fixes: 6dc06c08 ("net/mlx4: Fix the check in attaching steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.

Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.

broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).

Fixes: a1cba561 ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).

This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.

Fixes: 5b4e2900 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in mlx4_dbg debug message and also
change the phrasing of the message so that is is more readable
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.

The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-05-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.17

Hopefully the last fixes for 4.17. ssb is again causing problems so we
had to revert a commit and fix it better. Also a small fix to bcma and
some MAINTAINERS file updates.

ssb

* fix regression with all module PCI cards, for example using b43 and
  b44 drivers

* try again fixing a MIPS linker error

bcma

* fix truncated info log messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When link is down, writes to the device might fail with
-EIO. Userspace needs an indication when the status is resolved.  As a
fix, tun_net_open() attempts to wake up writers - but that is only
effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is
not the case of vhost_net which only poll for EPOLLOUT after it meets
errors during sendmsg().

This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when
socket is not writable or device is down to guarantee EPOLLOUT will be
raised in either tun_chr_poll() or tun_sock_write_space() after device
is up.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 1bd4978a ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason Wang says:

====================
Fix several issues of virtio-net mergeable XDP

Please review the patches that tries to fix several issues of
virtio-net mergeable XDP.

Changes from V1:
- check against 1 before decreasing instead of resetting to 1
- typoe fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to drop refcnt to xdp_page if we see a gso packet. Otherwise
it will be leaked. Fixing this by moving the check of gso packet above
the linearizing logic. While at it, remove useless comment as well.

Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 72979a6c ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we successfully linearize the packet, num_buf will be set to zero
which may confuse error handling path which assumes num_buf is at
least 1 and this can lead the code tries to pop the descriptor of next
buffer. Fixing this by checking num_buf against 1 before decreasing.

Fixes: 4941d472 ("virtio-net: do not reset during XDP set")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not go for the error path after successfully transmitting a
XDP buffer after linearizing. Since the error path may try to pop and
drop next packet and increase the drop counters. Fixing this by simply
drop the refcnt of original page and go for xmit path.

Fixes: 72979a6c ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After a linearized packet was redirected by XDP, we should not go for
the err path which will try to pop buffers for the next packet and
increase the drop counter. Fixing this by just drop the page refcnt
for the original page.

Fixes: 186b3c99 ("virtio-net: support XDP_REDIRECT")
Reported-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A handful of fixes:
 * hwsim radio dump wasn't working for the first radio
 * mesh was updating statistics incorrectly
 * a netlink message allocation was possibly too short
 * wiphy name limit was still too long
 * in certain cases regdb query could find a NULL pointer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.

Fix that mask to handle 64bit physical address.

Fixes: fe56b9e6 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 8fb472c0 ("ipmr: improve hash scalability")
added a call to rhltable_init() without checking its return value.

This problem was then later copied to IPv6 and factorized in commit
0bbbf0e7 ("ipmr, ip6mr: Unite creation of new mr_table")

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 31552 Comm: syz-executor7 Not tainted 4.17.0-rc5+ #60
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:rht_key_hashfn include/linux/rhashtable.h:277 [inline]
RIP: 0010:__rhashtable_lookup include/linux/rhashtable.h:630 [inline]
RIP: 0010:rhltable_lookup include/linux/rhashtable.h:716 [inline]
RIP: 0010:mr_mfc_find_parent+0x2ad/0xbb0 net/ipv4/ipmr_base.c:63
RSP: 0018:ffff8801826aef70 EFLAGS: 00010203
RAX: 0000000000000001 RBX: 0000000000000001 RCX: ffffc90001ea0000
RDX: 0000000000000079 RSI: ffffffff8661e859 RDI: 000000000000000c
RBP: ffff8801826af1c0 R08: ffff8801b2212000 R09: ffffed003b5e46c2
R10: ffffed003b5e46c2 R11: ffff8801daf23613 R12: dffffc0000000000
R13: ffff8801826af198 R14: ffff8801cf8225c0 R15: ffff8801826af658
FS:  00007ff7fa732700(0000) GS:ffff8801daf00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000003ffffff9c CR3: 00000001b0210000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 ip6mr_cache_find_parent net/ipv6/ip6mr.c:981 [inline]
 ip6mr_mfc_delete+0x1fe/0x6b0 net/ipv6/ip6mr.c:1221
 ip6_mroute_setsockopt+0x15c6/0x1d70 net/ipv6/ip6mr.c:1698
 do_ipv6_setsockopt.isra.9+0x422/0x4660 net/ipv6/ipv6_sockglue.c:163
 ipv6_setsockopt+0xbd/0x170 net/ipv6/ipv6_sockglue.c:922
 rawv6_setsockopt+0x59/0x140 net/ipv6/raw.c:1060
 sock_common_setsockopt+0x9a/0xe0 net/core/sock.c:3039
 __sys_setsockopt+0x1bd/0x390 net/socket.c:1903
 __do_sys_setsockopt net/socket.c:1914 [inline]
 __se_sys_setsockopt net/socket.c:1911 [inline]
 __x64_sys_setsockopt+0xbe/0x150 net/socket.c:1911
 do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 8fb472c0 ("ipmr: improve hash scalability")
Fixes: 0bbbf0e7 ("ipmr, ip6mr: Unite creation of new mr_table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Yuval Mintz <yuvalm@mellanox.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot reported the use-after-free in timer_is_static_object() [1].

This can happen because the structure for the rto timer (ccid2_hc_tx_sock)
is removed in dccp_disconnect(), and ccid2_hc_tx_rto_expire() can be
called after that.

The report [1] is similar to the one in commit 120e9dab ("dccp:
defer ccid_hc_tx_delete() at dismantle time"). And the fix is the same,
delay freeing ccid2_hc_tx_sock structure, so that it is freed in
dccp_sk_destruct().

[1]

==================================================================
BUG: KASAN: use-after-free in timer_is_static_object+0x80/0x90
kernel/time/timer.c:607
Read of size 8 at addr ffff8801bebb5118 by task syz-executor2/25299

CPU: 1 PID: 25299 Comm: syz-executor2 Not tainted 4.17.0-rc5+ #54
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  <IRQ>
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0x1b9/0x294 lib/dump_stack.c:113
  print_address_description+0x6c/0x20b mm/kasan/report.c:256
  kasan_report_error mm/kasan/report.c:354 [inline]
  kasan_report.cold.7+0x242/0x2fe mm/kasan/report.c:412
  __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
  timer_is_static_object+0x80/0x90 kernel/time/timer.c:607
  debug_object_activate+0x2d9/0x670 lib/debugobjects.c:508
  debug_timer_activate kernel/time/timer.c:709 [inline]
  debug_activate kernel/time/timer.c:764 [inline]
  __mod_timer kernel/time/timer.c:1041 [inline]
  mod_timer+0x4d3/0x13b0 kernel/time/timer.c:1102
  sk_reset_timer+0x22/0x60 net/core/sock.c:2742
  ccid2_hc_tx_rto_expire+0x587/0x680 net/dccp/ccids/ccid2.c:147
  call_timer_fn+0x230/0x940 kernel/time/timer.c:1326
  expire_timers kernel/time/timer.c:1363 [inline]
  __run_timers+0x79e/0xc50 kernel/time/timer.c:1666
  run_timer_softirq+0x4c/0x70 kernel/time/timer.c:1692
  __do_softirq+0x2e0/0xaf5 kernel/softirq.c:285
  invoke_softirq kernel/softirq.c:365 [inline]
  irq_exit+0x1d1/0x200 kernel/softirq.c:405
  exiting_irq arch/x86/include/asm/apic.h:525 [inline]
  smp_apic_timer_interrupt+0x17e/0x710 arch/x86/kernel/apic/apic.c:1052
  apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:863
  </IRQ>
...
Allocated by task 25374:
  save_stack+0x43/0xd0 mm/kasan/kasan.c:448
  set_track mm/kasan/kasan.c:460 [inline]
  kasan_kmalloc+0xc4/0xe0 mm/kasan/kasan.c:553
  kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490
  kmem_cache_alloc+0x12e/0x760 mm/slab.c:3554
  ccid_new+0x25b/0x3e0 net/dccp/ccid.c:151
  dccp_hdlr_ccid+0x27/0x150 net/dccp/feat.c:44
  __dccp_feat_activate+0x184/0x270 net/dccp/feat.c:344
  dccp_feat_activate_values+0x3a7/0x819 net/dccp/feat.c:1538
  dccp_create_openreq_child+0x472/0x610 net/dccp/minisocks.c:128
  dccp_v4_request_recv_sock+0x12c/0xca0 net/dccp/ipv4.c:408
  dccp_v6_request_recv_sock+0x125d/0x1f10 net/dccp/ipv6.c:415
  dccp_check_req+0x455/0x6a0 net/dccp/minisocks.c:197
  dccp_v4_rcv+0x7b8/0x1f3f net/dccp/ipv4.c:841
  ip_local_deliver_finish+0x2e3/0xd80 net/ipv4/ip_input.c:215
  NF_HOOK include/linux/netfilter.h:288 [inline]
  ip_local_deliver+0x1e1/0x720 net/ipv4/ip_input.c:256
  dst_input include/net/dst.h:450 [inline]
  ip_rcv_finish+0x81b/0x2200 net/ipv4/ip_input.c:396
  NF_HOOK include/linux/netfilter.h:288 [inline]
  ip_rcv+0xb70/0x143d net/ipv4/ip_input.c:492
  __netif_receive_skb_core+0x26f5/0x3630 net/core/dev.c:4592
  __netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4657
  process_backlog+0x219/0x760 net/core/dev.c:5337
  napi_poll net/core/dev.c:5735 [inline]
  net_rx_action+0x7b7/0x1930 net/core/dev.c:5801
  __do_softirq+0x2e0/0xaf5 kernel/softirq.c:285

Freed by task 25374:
  save_stack+0x43/0xd0 mm/kasan/kasan.c:448
  set_track mm/kasan/kasan.c:460 [inline]
  __kasan_slab_free+0x11a/0x170 mm/kasan/kasan.c:521
  kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
  __cache_free mm/slab.c:3498 [inline]
  kmem_cache_free+0x86/0x2d0 mm/slab.c:3756
  ccid_hc_tx_delete+0xc3/0x100 net/dccp/ccid.c:190
  dccp_disconnect+0x130/0xc66 net/dccp/proto.c:286
  dccp_close+0x3bc/0xe60 net/dccp/proto.c:1045
  inet_release+0x104/0x1f0 net/ipv4/af_inet.c:427
  inet6_release+0x50/0x70 net/ipv6/af_inet6.c:460
  sock_release+0x96/0x1b0 net/socket.c:594
  sock_close+0x16/0x20 net/socket.c:1149
  __fput+0x34d/0x890 fs/file_table.c:209
  ____fput+0x15/0x20 fs/file_table.c:243
  task_work_run+0x1e4/0x290 kernel/task_work.c:113
  tracehook_notify_resume include/linux/tracehook.h:191 [inline]
  exit_to_usermode_loop+0x2bd/0x310 arch/x86/entry/common.c:166
  prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline]
  syscall_return_slowpath arch/x86/entry/common.c:265 [inline]
  do_syscall_64+0x6ac/0x800 arch/x86/entry/common.c:290
  entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8801bebb4cc0
  which belongs to the cache ccid2_hc_tx_sock of size 1240
The buggy address is located 1112 bytes inside of
  1240-byte region [ffff8801bebb4cc0, ffff8801bebb5198)
The buggy address belongs to the page:
page:ffffea0006faed00 count:1 mapcount:0 mapping:ffff8801bebb41c0
index:0xffff8801bebb5240 compound_mapcount: 0
flags: 0x2fffc0000008100(slab|head)
raw: 02fffc0000008100 ffff8801bebb41c0 ffff8801bebb5240 0000000100000003
raw: ffff8801cdba3138 ffffea0007634120 ffff8801cdbaab40 0000000000000000
page dumped because: kasan: bad access detected
...
==================================================================

Reported-by: syzbot+5d47e9ec91a6f15dbd6f@syzkaller.appspotmail.com
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In divasmain.c, the function divas_write() firstly invokes the function
diva_xdi_open_adapter() to open the adapter that matches with the adapter
number provided by the user, and then invokes the function diva_xdi_write()
to perform the write operation using the matched adapter. The two functions
diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c.

In diva_xdi_open_adapter(), the user command is copied to the object 'msg'
from the userspace pointer 'src' through the function pointer 'cp_fn',
which eventually calls copy_from_user() to do the copy. Then, the adapter
number 'msg.adapter' is used to find out a matched adapter from the
'adapter_queue'. A matched adapter will be returned if it is found.
Otherwise, NULL is returned to indicate the failure of the verification on
the adapter number.

As mentioned above, if a matched adapter is returned, the function
diva_xdi_write() is invoked to perform the write operation. In this
function, the user command is copied once again from the userspace pointer
'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as
both of them are from the 'buf' pointer in divas_write(). Similarly, the
copy is achieved through the function pointer 'cp_fn', which finally calls
copy_from_user(). After the successful copy, the corresponding command
processing handler of the matched adapter is invoked to perform the write
operation.

It is obvious that there are two copies here from userspace, one is in
diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of
these two copies share the same source userspace pointer, i.e., the 'buf'
pointer in divas_write(). Given that a malicious userspace process can race
to change the content pointed by the 'buf' pointer, this can pose potential
security issues. For example, in the first copy, the user provides a valid
adapter number to pass the verification process and a valid adapter can be
found. Then the user can modify the adapter number to an invalid number.
This way, the user can bypass the verification process of the adapter
number and inject inconsistent data.

This patch reuses the data copied in
diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the
above issues can be avoided.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently there is no license information in the header of
this file.

The MODULE_LICENSE field contains ("GPL"), which means
GNU Public License v2 or later, so add a corresponding
SPDX license identifier.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now sctp uses inet_dgram_connect as its proto_ops .connect, and the flags
param can't be passed into its proto .connect where this flags is really
needed.

sctp works around it by getting flags from socket file in __sctp_connect.
It works for connecting from userspace, as inherently the user sock has
socket file and it passes f_flags as the flags param into the proto_ops
.connect.

However, the sock created by sock_create_kern doesn't have a socket file,
and it passes the flags (like O_NONBLOCK) by using the flags param in
kernel_connect, which calls proto_ops .connect later.

So to fix it, this patch defines a new proto_ops .connect for sctp,
sctp_inet_connect, which calls __sctp_connect() directly with this
flags param. After this, the sctp's proto .connect can be removed.

Note that sctp_inet_connect doesn't need to do some checks that are not
needed for sctp, which makes thing better than with inet_dgram_connect.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eugene hasn't worked on wcn36xx for some time now.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Luis hasn't worked on ath.ko for some time now.
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

I switched to use my codeaurora.org address.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since 6335698e the radio with idx of 0
will not get dumped in HWSIM_CMD_GET_RADIO because of the last_idx
checks.  Offset cb->args[0] by 1 similarly to what is done in nl80211.c.

Fixes: 6335698e ("mac80211_hwsim: add generation count for netlink dump operation")
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers may call this function when regdb is not initialized yet,
so we need to make sure regdb is valid before trying to access it.

Make sure regdb is initialized before trying to access it in
reg_query_regdb_wmm() and query_regdb().
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull MIPS fixes from James Hogan:

 - fix build with DEBUG_ZBOOT and MACH_JZ4770 (4.16)

 - include xilfpga FDT in fitImage and stop generating dtb.o (4.15)

 - fix software IO coherence on CM SMP systems (4.8)

 - ptrace: Fix PEEKUSR/POKEUSR to o32 FGRs (3.14)

 - ptrace: Expose FIR register through FP regset (3.13)

 - fix typo in KVM debugfs file name (3.10)

* tag 'mips_fixes_4.17_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: Fix ptrace(2) PTRACE_PEEKUSR and PTRACE_POKEUSR accesses to o32 FGRs
  MIPS: xilfpga: Actually include FDT in fitImage
  MIPS: xilfpga: Stop generating useless dtb.o
  KVM: Fix spelling mistake: "cop_unsuable" -> "cop_unusable"
  MIPS: ptrace: Expose FIR register through FP regset
  MIPS: Fix build with DEBUG_ZBOOT and MACH_JZ4770
  MIPS: c-r4k: Fix data corruption related to cache coherence

Pull networking fixes from David Miller:

 1) Fix refcounting bug for connections in on-packet scheduling mode of
    IPVS, from Julian Anastasov.

 2) Set network header properly in AF_PACKET's packet_snd, from Willem
    de Bruijn.

 3) Fix regressions in 3c59x by converting to generic DMA API. It was
    relying upon the hack that the PCI DMA interfaces would accept NULL
    for EISA devices. From Christoph Hellwig.

 4) Remove RDMA devices before unregistering netdev in QEDE driver, from
    Michal Kalderon.

 5) Use after free in TUN driver ptr_ring usage, from Jason Wang.

 6) Properly check for missing netlink attributes in SMC_PNETID
    requests, from Eric Biggers.

 7) Set DMA mask before performaing any DMA operations in vmxnet3
    driver, from Regis Duchesne.

 8) Fix mlx5 build with SMP=n, from Saeed Mahameed.

 9) Classifier fixes in bcm_sf2 driver from Florian Fainelli.

10) Tuntap use after free during release, from Jason Wang.

11) Don't use stack memory in scatterlists in tls code, from Matt
    Mullins.

12) Not fully initialized flow key object in ipv4 routing code, from
    David Ahern.

13) Various packet headroom bug fixes in ip6_gre driver, from Petr
    Machata.

14) Remove queues from XPS maps using correct index, from Amritha
    Nambiar.

15) Fix use after free in sock_diag, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits)
  net: ip6_gre: fix tunnel metadata device sharing.
  cxgb4: fix offset in collecting TX rate limit info
  net: sched: red: avoid hashing NULL child
  sock_diag: fix use-after-free read in __sk_free
  sh_eth: Change platform check to CONFIG_ARCH_RENESAS
  net: dsa: Do not register devlink for unused ports
  net: Fix a bug in removing queues from XPS map
  bpf: fix truncated jump targets on heavy expansions
  bpf: parse and verdict prog attach may race with bpf map update
  bpf: sockmap update rollback on error can incorrectly dec prog refcnt
  net: test tailroom before appending to linear skb
  net: ip6_gre: Fix ip6erspan hlen calculation
  net: ip6_gre: Split up ip6gre_changelink()
  net: ip6_gre: Split up ip6gre_newlink()
  net: ip6_gre: Split up ip6gre_tnl_change()
  net: ip6_gre: Split up ip6gre_tnl_link_config()
  net: ip6_gre: Fix headroom request in ip6erspan_tunnel_xmit()
  net: ip6_gre: Request headroom in __gre6_xmit()
  selftests/bpf: check return value of fopen in test_verifier.c
  erspan: fix invalid erspan version.
  ...