The F81532/534 had 3 output pin (M0/SD, M1, M2) with open-drain mode to
control transceiver. We'll read it from internal Flash with address
0x2f05~0x2f08 for 4 ports. The value is range from 0 to 7. The M0/SD is
MSB of this value. For a examples, If read value is 6, we'll write M0/SD,
M1, M2 as 1, 1, 0.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
	0: F81534_PORT_CONF_RS232.
	1: F81534_PORT_CONF_RS485.
	2: value error, default to F81534_PORT_CONF_RS232.
	3: F81534_PORT_CONF_RS485_INVERT.

F81532/534 Clock register (offset +08h)

Bit0:	UART Enable (always on)
Bit2-1:	Clock source selector
			00: 1.846MHz.
			01: 18.46MHz.
			10: 24MHz.
			11: 14.77MHz.
Bit4:	Auto direction(RTS) control (RTS pin Low when TX)
Bit5:	Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: rename mode-mask define, and only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>

The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.

This device may generate data overrun when baud rate setting to 921600bps
or higher with old UART trigger level setting (8x14=112) with full
loading. We'll change trigger level from 8x14=112 to 8x8=64 to avoid data
overrun.

Also the read/write of EP0 will be affected by this patch. The worst case
of responding time is 20s when all serial port are full loading and trying
to access EP0, so we change EP0 timeout from 10 to 20s.

F81532/534 Clock register (offset +08h)

Bit0:	UART Enable (always on)
Bit2-1:	Clock source selector
			00: 1.846MHz.
			01: 18.46MHz.
			10: 24MHz.
			11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>

The patch moves TIOCGSERIAL ioctl case to get_serial_info function.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: keep the automatic __user pointer variable in ioctl callback ]
Signed-off-by: Johan Hovold <johan@kernel.org>

The patch removes unused TIOCSSERIAL ioctl case and adds the default block
to the switch. This will make the ioctl return -ENOTTY to user space (e.g.
setserial), which indicates that TIOCSSERIAL really isn't supported for
these devices currently.

Note that these (dummy) ioctl implementations where added by commit
2f430b4b ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl
calls.") back in 2006. This in turn appears to have been triggered by a
change in a user space tool, wvdial, which started erroring out if
either was missing.

There are some bug reports about that against wvdial from around that
time, and looking at the wvstreams (library) code now, it looks like the
issue has indeed been resolved by handling errors more gracefully (e.g.
just logging them).

User space really should not make assumptions about these ioctl always
being implemented, but if this turns out to be a problem for anyone
using this driver, we'll add TIOCSSERIAL back in some form.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: amend commit message with backstory ]
Signed-off-by: Johan Hovold <johan@kernel.org>

According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
   process_rcvd_data
     process_rcvd_status
       change_port_settings
         send_iosp_ext_cmd
           write_cmd_usb
             usb_kill_urb --> may sleep

To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.

This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

write_reg returns 0 on success, we can make it more explicit by returning
number 0 instead of result variable.

read_reg should return 0 on success since this is a more common pattern.

The user of read_reg has been clean-up and should be at the same commit.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

The assignment of DIV to itself is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>

Pull ARM fixes from Russell King:

 - LPAE fixes for kernel-readonly regions

 - Fix for get_user_pages_fast on LPAE systems

 - avoid tying decompressor to a particular platform if DEBUG_LL is
   enabled

 - BUG if we attempt to return to userspace but the to-be-restored PSR
   value keeps us in privileged mode (defeating an issue that ftracetest
   found)

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: BUG if jumping to usermode address in kernel mode
  ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
  ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
  ARM: make decompressor debug output user selectable
  ARM: fix get_user_pages_fast

Pull irq fixes from Thomas Glexiner:

 - unbreak the irq trigger type check for legacy platforms

 - a handful fixes for ARM GIC v3/4 interrupt controllers

 - a few trivial fixes all over the place

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Make - vs ?: Precedence explicit
  irqchip/imgpdc: Use resource_size function on resource object
  irqchip/qcom: Fix u32 comparison with value less than zero
  irqchip/exiu: Fix return value check in exiu_init()
  irqchip/gic-v3-its: Remove artificial dependency on PCI
  irqchip/gic-v4: Add forward definition of struct irq_domain_ops
  irqchip/gic-v3: pr_err() strings should end with newlines
  irqchip/s3c24xx: pr_err() strings should end with newlines
  irqchip/gic-v3: Fix ppi-partitions lookup
  irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
  genirq: Track whether the trigger type has been set

Pull misc x86 fixes from Ingo Molnar:
 - topology enumeration fixes
 - KASAN fix
 - two entry fixes (not yet the big series related to KASLR)
 - remove obsolete code
 - instruction decoder fix
 - better /dev/mem sanity checks, hopefully working better this time
 - pkeys fixes
 - two ACPI fixes
 - 5-level paging related fixes
 - UMIP fixes that should make application visible faults more debuggable
 - boot fix for weird virtualization environment

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  x86/decoder: Add new TEST instruction pattern
  x86/PCI: Remove unused HyperTransport interrupt support
  x86/umip: Fix insn_get_code_seg_params()'s return value
  x86/boot/KASLR: Remove unused variable
  x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
  x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
  x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
  x86/pkeys/selftests: Fix protection keys write() warning
  x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
  x86/mpx/selftests: Fix up weird arrays
  x86/pkeys: Update documentation about availability
  x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
  x86/smpboot: Fix __max_logical_packages estimate
  x86/topology: Avoid wasting 128k for package id array
  perf/x86/intel/uncore: Cache logical pkg id in uncore driver
  x86/acpi: Reduce code duplication in mp_override_legacy_irq()
  x86/acpi: Handle SCI interrupts above legacy space gracefully
  x86/boot: Fix boot failure when SMP MP-table is based at 0
  x86/mm: Limit mmap() of /dev/mem to valid physical addresses
  x86/selftests: Add test for mapping placement for 5-level paging
  ...

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: a documentation fix, a Sparse warning fix and a debugging
  fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix task state recording/printout
  sched/deadline: Don't use dubious signed bitfields
  sched/deadline: Fix the description of runtime accounting in the documentation

Pull perf fixes from Ingo Molnar:
 "Misc fixes: two PMU driver fixes and a memory leak fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix memory leak triggered by perf --namespace
  perf/x86/intel/uncore: Add event constraint for BDX PCU
  perf/x86/intel: Hide TSX events when RTM is not supported

Pull static key fix from Ingo Molnar:
 "Fix a boot warning related to bad init ordering of the static keys
  self-test"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Invoke jump_label_test() via early_initcall()

Pull objtool fixes from Ingo Molnar:
 "A handful of objtool fixes, most of them related to making the UAPI
  header-syncing warnings easier to read and easier to act upon"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Sync objtool UAPI header
  objtool: Fix cross-build
  objtool: Move kernel headers/code sync check to a script
  objtool: Move synced files to their original relative locations
  objtool: Make unreachable annotation inline asms explicitly volatile
  objtool: Add a comment for the unreachable annotation macros

Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode.  This
could occur due to corrupted stack state, which has been observed with
"ftracetest".

This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Pull timer updates from Thomas Gleixner:

 - The final conversion of timer wheel timers to timer_setup().

   A few manual conversions and a large coccinelle assisted sweep and
   the removal of the old initialization mechanisms and the related
   code.

 - Remove the now unused VSYSCALL update code

 - Fix permissions of /proc/timer_list. I still need to get rid of that
   file completely

 - Rename a misnomed clocksource function and remove a stale declaration

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  m68k/macboing: Fix missed timer callback assignment
  treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
  timer: Remove redundant __setup_timer*() macros
  timer: Pass function down to initialization routines
  timer: Remove unused data arguments from macros
  timer: Switch callback prototype to take struct timer_list * argument
  timer: Pass timer_list pointer to callbacks unconditionally
  Coccinelle: Remove setup_timer.cocci
  timer: Remove setup_*timer() interface
  timer: Remove init_timer() interface
  treewide: setup_timer() -> timer_setup() (2 field)
  treewide: setup_timer() -> timer_setup()
  treewide: init_timer() -> setup_timer()
  treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
  s390: cmm: Convert timers to use timer_setup()
  lightnvm: Convert timers to use timer_setup()
  drivers/net: cris: Convert timers to use timer_setup()
  drm/vc4: Convert timers to use timer_setup()
  block/laptop_mode: Convert timers to use timer_setup()
  net/atm/mpc: Avoid open-coded assignment of timer callback function
  ...

Pull ARC updates from Vineet Gupta:

 - more changes for HS48 cores: supporting MMUv5, detecting new
   micro-arch gizmos

 - axs10x platform wiring up reset driver merged in this cycle

 - ARC perf driver optimizations

* tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: perf: avoid vmalloc backed mmap
  ARCv2: perf: optimize given that num counters <= 32
  ARCv2: perf: tweak overflow interrupt
  ARC: [plat-axs10x] DTS: Add reset controller node to manage ethernet reset
  ARCv2: boot log: updates for HS48: dual-issue, ECC, Loop Buffer
  ARCv2: Accomodate HS48 MMUv5 by relaxing MMU ver checking
  ARC: [plat-axs10x] auto-select AXS101 or AXS103 given the  ISA config

Pull more Kbuild updates from Masahiro Yamada:

 - use 'pwd' instead of '/bin/pwd' for portability

 - clean up Makefiles

 - fix ld-option for clang

 - fix malloc'ed data size in Kconfig

 - fix parallel building along with coccicheck

 - fix a minor issue of package building

 - prompt to use "rpm-pkg" instead of "rpm"

 - clean up *.i and *.lst patterns by "make clean"

* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: drop $(extra-y) from real-objs-y
  kbuild: clean up *.i and *.lst patterns by make clean
  kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
  kbuild: pkg: use --transform option to prefix paths in tar
  coccinelle: fix parallel build with CHECK=scripts/coccicheck
  kconfig/symbol.c: use correct pointer type argument for sizeof
  kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
  kbuild: remove all dummy assignments to obj-
  kbuild: create built-in.o automatically if parent directory wants it
  kbuild: /bin/pwd -> pwd

Pull AFS fixes from David Howells:

 - Make AFS file locking work again.

 - Don't write to a page that's being written out, but wait for it to
   complete.

 - Do d_drop() and d_add() in the right places.

 - Put keys on error paths.

 - Remove some redundant code.

* tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: remove redundant assignment of dvnode to itself
  afs: cell: Remove unnecessary code in afs_lookup_cell
  afs: Fix signal handling in some file ops
  afs: Fix some dentry handling in dir ops and missing key_puts
  afs: Make afs_write_begin() avoid writing to a page that's being stored
  afs: Fix file locking

Pull KVM updates from Radim Krčmář:
 "Trimmed second batch of KVM changes for Linux 4.15:

   - GICv4 Support for KVM/ARM

   - re-introduce support for CPUs without virtual NMI (cc stable) and
     allow testing of KVM without virtual NMI on available CPUs

   - fix long-standing performance issues with assigned devices on AMD
     (cc stable)"

* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
  kvm: vmx: Allow disabling virtual NMI support
  kvm: vmx: Reinstate support for CPUs without virtual NMI
  KVM: SVM: obey guest PAT
  KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
  KVM: arm/arm64: Fix GICv4 ITS initialization issues
  KVM: arm/arm64: GICv4: Theory of operations
  KVM: arm/arm64: GICv4: Enable VLPI support
  KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
  KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
  KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
  KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
  KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
  KVM: arm/arm64: GICv4: Add doorbell interrupt handling
  KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
  KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
  KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
  KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
  KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
  KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
  KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
  ...

Pull powerpc fixes from Michael Ellerman:
 "A small batch of fixes, about 50% tagged for stable and the rest for
  recently merged code.

  There's one more fix for the >128T handling on hash. Once a process
  had requested a single mmap above 128T we would then always search
  above 128T. The correct behaviour is to consider the hint address in
  isolation for each mmap request.

  Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
  VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
  identify P9 DD2.1 but in code that is currently not used by default.

  Thanks to: Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan,
  Sukadev Bhattiprolu"

* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
  powerpc/perf: Fix IMC_MAX_PMU macro
  powerpc/perf: Fix pmu_count to count only nest imc pmus
  powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
  powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
  powerpc/vas: Export chip_to_vas_id()
  powerpc/64s/slice: Use addr limit when computing slice mask

Pull SCSI target updates from Nicholas Bellinger:

 "This series is predominantly bug-fixes, with a few small improvements
  that have been outstanding over the last release cycle.

  As usual, the associated bug-fixes have CC' tags for stable.

  Also, things have been particularly quiet wrt new developments the
  last months, with most folks continuing to focus on stability atop 4.x
  stable kernels for their respective production configurations.

  Also at this point, the stable trees have been synced up with
  mainline. This will continue to be a priority, as production users
  tend to run exclusively atop stable kernels, a few releases behind
  mainline.

  The highlights include:

   - Fix PR PREEMPT_AND_ABORT null pointer dereference regression in
     v4.11+ (tangwenji)

   - Fix OOPs during removing TCMU device (Xiubo Li + Zhang Zhuoyu)

   - Add netlink command reply supported option for each device (Kenjiro
     Nakayama)

   - cxgbit: Abort the TCP connection in case of data out timeout (Varun
     Prakash)

   - Fix PR/ALUA file path truncation (David Disseldorp)

   - Fix double se_cmd completion during ->cmd_time_out (Mike Christie)

   - Fix QUEUE_FULL + SCSI task attribute handling in 4.1+ (Bryant Ly +
     nab)

   - Fix quiese during transport_write_pending_qf endless loop (nab)

   - Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK in 3.14+
     (Don White + nab)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (35 commits)
  tcmu: Add a missing unlock on an error path
  tcmu: Fix some memory corruption
  iscsi-target: Fix non-immediate TMR reference leak
  iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
  target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
  target: Fix quiese during transport_write_pending_qf endless loop
  target: Fix caw_sem leak in transport_generic_request_failure
  target: Fix QUEUE_FULL + SCSI task attribute handling
  iSCSI-target: Use common error handling code in iscsi_decode_text_input()
  target/iscsi: Detect conn_cmd_list corruption early
  target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()
  target/iscsi: Modify iscsit_do_crypto_hash_buf() prototype
  target/iscsi: Fix endianness in an error message
  target/iscsi: Use min() in iscsit_dump_data_payload() instead of open-coding it
  target/iscsi: Define OFFLOAD_BUF_SIZE once
  target: Inline transport_put_cmd()
  target: Suppress gcc 7 fallthrough warnings
  target: Move a declaration of a global variable into a header file
  tcmu: fix double se_cmd completion
  target: return SAM_STAT_TASK_SET_FULL for TCM_OUT_OF_RESOURCES
  ...

This fixes a missed function prototype callback from the timer conversions.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20171123221902.GA75727@beast

The assignment of dvnode to itself is redundant and can be removed.
Cleans up warning detected by cppcheck:

fs/afs/dir.c:975: (warning) Redundant assignment of 'dvnode' to itself.

Fixes: d2ddc776 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David Howells <dhowells@redhat.com>

Due to recent changes this piece of code is no longer needed.

Addresses-Coverity-ID: 1462033
Link: https://lkml.kernel.org/r/4923.1510957307@warthog.procyon.org.ukSigned-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David Howells <dhowells@redhat.com>

afs_mkdir(), afs_create(), afs_link() and afs_symlink() all need to drop
the target dentry if a signal causes the operation to be killed immediately
before we try to contact the server.
Signed-off-by: David Howells <dhowells@redhat.com>

Fix some of dentry handling in AFS directory ops:

 (1) Do d_drop() on the new_dentry before assigning a new inode to it in
     afs_vnode_new_inode().  It's fine to do this before calling afs_iget()
     because the operation has taken place on the server.

 (2) Replace d_instantiate()/d_rehash() with d_add().

 (3) Don't d_drop() the new_dentry in afs_rename() on error.

Also fix afs_link() and afs_rename() to call key_put() on all error paths
where the key is taken.
Signed-off-by: David Howells <dhowells@redhat.com>

Make afs_write_begin() wait for a page that's marked PG_writeback because:

 (1) We need to avoid interference with the data being stored so that the
     data on the server ends up in a defined state.

 (2) page->private is used to track the window of dirty data within a page,
     but it's also used by the storage code to track what's being written,
     being cleared by the completion notification.  Ownership can't be
     relinquished by the storage code until completion because it a store
     fails, the data must be remarked dirty.

Tracing shows something like the following (edited):

 x86_64-linux-gn-15940 [1] afs_page_dirty: vn=ffff8800bef33800 9c75 begin 0-125
    kworker/u8:3-114   [2] afs_page_dirty: vn=ffff8800bef33800 9c75 store+ 0-125
 x86_64-linux-gn-15940 [1] afs_page_dirty: vn=ffff8800bef33800 9c75 begin 0-2052
    kworker/u8:3-114   [2] afs_page_dirty: vn=ffff8800bef33800 9c75 clear 0-2052
    kworker/u8:3-114   [2] afs_page_dirty: vn=ffff8800bef33800 9c75 store 0-0
    kworker/u8:3-114   [2] afs_page_dirty: vn=ffff8800bef33800 9c75 WARN 0-0

The clear (completion) corresponding to the store+ (store continuation from
a previous page) happens between the second begin (afs_write_begin) and the
store corresponding to that.  This results in the second store not seeing
any data to write back, leading to the following warning:

WARNING: CPU: 2 PID: 114 at ../fs/afs/write.c:403 afs_write_back_from_locked_page+0x19d/0x76c [kafs]
Modules linked in: kafs(E)
CPU: 2 PID: 114 Comm: kworker/u8:3 Tainted: G            E   4.14.0-fscache+ #242
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Workqueue: writeback wb_workfn (flush-afs-2)
task: ffff8800cad72600 task.stack: ffff8800cad44000
RIP: 0010:afs_write_back_from_locked_page+0x19d/0x76c [kafs]
RSP: 0018:ffff8800cad47aa0 EFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff8800bef33a20 RCX: 0000000000000000
RDX: 000000000000000f RSI: ffffffff81c5d0e0 RDI: ffff8800cad72e78
RBP: ffff8800d31ea1e8 R08: ffff8800c1358000 R09: ffff8800ca00e400
R10: ffff8800cad47a38 R11: ffff8800c5d9e400 R12: 0000000000000000
R13: ffffea0002d9df00 R14: ffffffffa0023c1c R15: 0000000000007fdf
FS:  0000000000000000(0000) GS:ffff8800ca700000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f85ac6c4000 CR3: 0000000001c10001 CR4: 00000000001606e0
Call Trace:
 ? clear_page_dirty_for_io+0x23a/0x267
 afs_writepages_region+0x1be/0x286 [kafs]
 afs_writepages+0x60/0x127 [kafs]
 do_writepages+0x36/0x70
 __writeback_single_inode+0x12f/0x635
 writeback_sb_inodes+0x2cc/0x452
 __writeback_inodes_wb+0x68/0x9f
 wb_writeback+0x208/0x470
 ? wb_workfn+0x22b/0x565
 wb_workfn+0x22b/0x565
 ? worker_thread+0x230/0x2ac
 process_one_work+0x2cc/0x517
 ? worker_thread+0x230/0x2ac
 worker_thread+0x1d4/0x2ac
 ? rescuer_thread+0x29b/0x29b
 kthread+0x15d/0x165
 ? kthread_create_on_node+0x3f/0x3f
 ? call_usermodehelper_exec_async+0x118/0x11f
 ret_from_fork+0x24/0x30
Signed-off-by: David Howells <dhowells@redhat.com>

The recent conversion of the task state recording to use task_state_index()
broke the sched_switch tracepoint task state output.

task_state_index() returns surprisingly an index (0-7) which is then
printed with __print_flags() applying bitmasks. Not really working and
resulting in weird states like 'prev_state=t' instead of 'prev_state=I'.

Use TASK_REPORT_MAX instead of TASK_STATE_MAX to report preemption. Build a
bitmask from the return value of task_state_index() and store it in
entry->prev_state, which makes __print_flags() work as expected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: stable@vger.kernel.org
Fixes: efb40f58 ("sched/tracing: Fix trace_sched_switch task-state printing")
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1711221304180.1751@nanosSigned-off-by: Ingo Molnar <mingo@kernel.org>

The kbuild test robot reported this build warning:

  Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c

  Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
  Warning: objdump says 3 bytes, but insn_get_length() says 2
  Warning: decoded and checked 1569014 instructions with 1 warnings

This sequence seems to be a new instruction not in the opcode map in the Intel SDM.

The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"

In that table, opcodes listed by the index REG bits as:

  000         001       010 011  100        101        110         111
 TEST Ib/Iz,(undefined),NOT,NEG,MUL AL/rAX,IMUL AL/rAX,DIV AL/rAX,IDIV AL/rAX

So, it seems TEST Ib is assigned to 001.

Add the new pattern.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull networking fixes from David Miller:

 1) Fix PCI IDs of 9000 series iwlwifi devices, from Luca Coelho.

 2) bpf offload bug fixes from Jakub Kicinski.

 3) Fix bpf verifier to NOP out code which is dead at run time because
    due to branch pruning the verifier will not explore such
    instructions. From Alexei Starovoitov.

 4) Fix crash when deleting secondary chains in packet scheduler
    classifier. From Roman Kapl.

 5) Fix buffer management bugs in smc, from Ursula Braun.

 6) Fix regression in anycast route handling, from David Ahern.

 7) Fix link settings regression in r8169, from Tobias Jakobi.

 8) Add back enough UFO support so that live migration still works, from
    Willem de Bruijn.

 9) Linearize enough packet data for the full extent to which the ipvlan
    code will inspect the packet headers, from Gao Feng.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
  ipvlan: Fix insufficient skb linear check for ipv6 icmp
  ipvlan: Fix insufficient skb linear check for arp
  geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
  net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
  net: accept UFO datagrams from tuntap and packet
  net: realtek: r8169: implement set_link_ksettings()
  net: ipv6: Fixup device for anycast routes during copy
  net/smc: Fix preinitialization of buf_desc in __smc_buf_create()
  net/smc: use sk_rcvbuf as start for rmb creation
  ipv6: Do not consider linkdown nexthops during multipath
  net: sched: fix crash when deleting secondary chains
  net: phy: cortina: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
  bpf: fix branch pruning logic
  bpf: change bpf_perf_event_output arg5 type to ARG_CONST_SIZE_OR_ZERO
  bpf: change bpf_probe_read_str arg2 type to ARG_CONST_SIZE_OR_ZERO
  bpf: remove explicit handling of 0 for arg2 in bpf_probe_read
  bpf: introduce ARG_PTR_TO_MEM_OR_NULL
  i40evf: Use smp_rmb rather than read_barrier_depends
  fm10k: Use smp_rmb rather than read_barrier_depends
  igb: Use smp_rmb rather than read_barrier_depends
  ...

Pull x86 platform driver fixes from Darren Hart:
 "Fix two issues resulting from the dell-smbios refactoring and
  introduction of the dell-smbios-wmi dispatcher.

  The first ensures a proper error code is returned when kzalloc fails.

  The second avoids an issue in older Dell BIOS implementations which
  would fail if the more complex calls were made by limiting those
  platforms to the simple calls such as those used by the existing
  dell-laptop and dell-wmi drivers, preserving their functionality prior
  to the addition of the dell-smbios-wmi dispatcher"

* tag 'platform-drivers-x86-v4.15-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: dell-laptop: fix error return code in dell_init()
  platform/x86: dell-smbios-wmi: Disable userspace interface if missing hotfix

Pull SCSI fixes from James Bottomley:
 "Two basic fixes: one for the sparse problem with the blacklist flags
  and another for a hang forever in bnx2i"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: Use 'blist_flags_t' for scsi_devinfo flags
  scsi: bnx2fc: Fix hung task messages when a cleanup response is not received during abort

Pull sound fixes from Takashi Iwai:
 "All commits found here are small fixes for regression or stable:

   - PCM timestamp behavior fix that could be seen as a regression

   - Remove spurious WARN_ON() from ALSA timer 32bit compat ioctl

   - HD-audio HDMI/DP channel mapping fix for 32bit archs

   - Fix the previous fix for HD-audio initialization code

   - More hardening USB-audio against malicious USB descriptors

   - HD-audio quirks/fixes (Realtek codec, AMD controller)

   - Missing help text for the recent Intel SST kconfig change"

* tag 'sound-fix-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda: Add Raven PCI ID
  ALSA: hda/realtek - Fix ALC700 family no sound issue
  ALSA: hda - Fix yet remaining issue with vmaster 0dB initialization
  ALSA: usb-audio: Add sanity checks in v2 clock parsers
  ALSA: usb-audio: Fix potential zero-division at parsing FU
  ALSA: usb-audio: Fix potential out-of-bound access at parsing SU
  ALSA: usb-audio: Add sanity checks to FE parser
  ALSA: timer: Remove kernel warning at compat ioctl error paths
  ALSA: pcm: update tstamp only if audio_tstamp changed
  ALSA: hda/realtek: Add headset mic support for Intel NUC Skull Canyon
  ALSA: hda: Fix too short HDMI/DP chmap reporting
  ALSA: usb-audio: uac1: Invalidate ctl on interrupt
  ALSA: hda/realtek - Fix ALC275 no sound issue
  ASoC: Intel: Add help text for SND_SOC_INTEL_SST_TOPLEVEL

Pull more drm updates from Dave Airlie:
 "Fixes/cleanups for rc1, non-desktop flags for VR

   - remove the MSM dt-bindings file Rob managed to push in the previous
     pull.

   - add a property/edid quirk to denote HMD devices, I had these
     hanging around for a few weeks and Keith had done some work on
     them, they are fairly self contained and small, and only affect
     people using HTC Vive VR headsets so far.

   - amdgpu, tegra, tilcdc, fsl fixes

   - some imx-drm cleanups I missed, these seemed pretty small, and no
     reason to hold off.

  I have one TTM regression fix (fixes bochs-vga in qemu) sitting
  locally awaiting review I'll probably send that in a separate pull
  request tomorrow"

* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
  dt-bindings: remove file that was added accidentally
  drm/edid: quirk HTC vive headset as non-desktop. [v2]
  drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
  drm: add connector info/property for non-desktop displays [v2]
  drm/amdgpu: fix rmmod KCQ disable failed error
  drm/amdgpu: fix kernel hang when starting VNC server
  drm/amdgpu: don't skip attributes when powerplay is enabled
  drm/amd/pp: fix typecast error in powerplay.
  drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
  drm/tegra: sor: Reimplement pad clock
  Revert "drm/radeon: dont switch vt on suspend"
  drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
  drm/amd/powerplay: fix unfreeze level smc message for smu7
  drm/amdgpu:fix memleak
  drm/amdgpu:fix memleak in takedown
  drm/amd/pp: fix dpm randomly failed on Vega10
  drm/amdgpu: set f_mapping on exported DMA-bufs
  drm/amdgpu: Properly allocate VM invalidate eng v2
  drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
  drm/fsl-dcu: avoid disabling pixel clock twice on suspend
  ...

Pull documentation updates from Jonathan Corbet:
 "A few late-arriving docs updates that have no real reason to wait.

  There's a new "Co-Developed-by" tag described by Greg, and a build
  enhancement from Willy to generate docs warnings during a kernel build
  (but only when additional warnings have been requested in general)"

* tag 'docs-4.15-2' of git://git.lwn.net/linux:
  Add optional check for bad kernel-doc comments
  Documentation: fix profile= options in kernel-parameters.txt
  documentation/svga.txt: update outdated file
  kokr/memory-barriers.txt: Fix typo in paring example
  kokr/memory-barriers/txt: Replace uses of "transitive"
  Documentation/process: add Co-Developed-by: tag for patches with multiple authors

Pull keys update from James Morris:
 "There's nothing too controversial here:

   - Doc fix for keyctl_read().

   - time_t -> time64_t replacement.

   - Set the module licence on things to prevent tainting"

* 'next-keys' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  pkcs7: Set the module licence to prevent tainting
  security: keys: Replace time_t with time64_t for struct key_preparsed_payload
  security: keys: Replace time_t/timespec with time64_t
  KEYS: fix in-kernel documentation for keyctl_read()

Merge tag 'apparmor-pr-2017-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor updates from John Johansen:
 "No features this time, just minor cleanups and bug fixes.

  Cleanups:
   - fix spelling mistake: "resoure" -> "resource"
   - remove unused redundant variable stop
   - Fix bool initialization/comparison

  Bug Fixes:
   - initialized returned struct aa_perms
   - fix leak of null profile name if profile allocation fails
   - ensure that undecidable profile attachments fail
   - fix profile attachment for special unconfined profiles
   - fix locking when creating a new complain profile.
   - fix possible recursive lock warning in __aa_create_ns"

* tag 'apparmor-pr-2017-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: fix possible recursive lock warning in __aa_create_ns
  apparmor: fix locking when creating a new complain profile.
  apparmor: fix profile attachment for special unconfined profiles
  apparmor: ensure that undecidable profile attachments fail
  apparmor: fix leak of null profile name if profile allocation fails
  apparmor: remove unused redundant variable stop
  apparmor: Fix bool initialization/comparison
  apparmor: initialized returned struct aa_perms
  apparmor: fix spelling mistake: "resoure" -> "resource"