On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).

The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org

On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).

So let's add a property for declaring such secure regions so that the
drivers can skip touching them.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-3-manivannan.sadhasivam@linaro.org

Convert Qcom NANDc devicetree binding to YAML.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-2-manivannan.sadhasivam@linaro.org

The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.

Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210325102337.481172-1-s.riedmueller@phytec.de

The module misses MODULE_DEVICE_TABLE() for both SPI and OF ID tables
and thus never autoloads on ID matches.
Add the missing declarations.
Present since day-0 of spinand framework introduction.

Fixes: 7529df46 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323173714.317884-1-alobakin@pm.me

Suppresses the following coccinelle warning:

drivers/mtd/nand/raw/rockchip-nand-controller.c:162:4-8: WARNING use flexible-array member instead
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323131137.45552-1-zou_wei@huawei.com

Update MTD ECC statistics with the number of corrected bits.

Fixes: f88fc122 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable@vger.kernel.org
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210322150714.101585-1-tudor.ambarus@microchip.com

i.MX is a DT-only platform, so of_match_ptr() can be safely
removed.

Remove the unneeded of_match_ptr().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210316000042.200392-1-festevam@gmail.com

The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1615770495-31939-1-git-send-email-tiantao6@hisilicon.com

'linux/mtd/nand.h' included in 'rawnand.h' is duplicated.
It is also included in the 17th line.
Signed-off-by: Zhang Yunkai <zhang.yunkai@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210313105702.365878-1-zhang.yunkai@zte.com.cn

This change makes sure that Broadcom NAND driver moves to interrupt
polling on the first brcmnand_write() call.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210311170909.9031-2-kdasu.kdev@gmail.com

Added support to read/write oob during EDU transfers.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210311170909.9031-1-kdasu.kdev@gmail.com

In qcom_probe_nand_devices() function, the error code returned by
qcom_nand_host_init_and_register() is converted to -ENODEV in the case
of failure. This poses issue if -EPROBE_DEFER is returned when the
dependency is not available for a component like parser.

So let's restructure the error handling logic a bit and return the
actual error code in case of qcom_nand_host_init_and_register() failure.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

There are chances that the parse_mtd_partitions() function will return
-EPROBE_DEFER in mtd_device_parse_register(). This might happen when
the dependency is not available for the parser. For instance, on SDX55
the MTD_QCOMSMEM_PARTS parser depends on the QCOM_SMEM driver to parse
the partitions defined in the shared memory region. With the current
flow, the error returned from parse_mtd_partitions() will be discarded
in favor of trying to add the fallback partition.

This will prevent the driver to end up in probe deferred pool and the
partitions won't be parsed even after the QCOM_SMEM driver is available.

Fix this issue by bailing out of mtd_device_parse_register() when
-EPROBE_DEFER error is returned from parse_mtd_partitions() function and
propagate the error code to the driver core for probing later.

Fixes: 5ac67ce3 ("mtd: move code adding (registering) partitions to the parse_mtd_partitions()")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.

Fixes: 27c5b17c ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com

From QPIC v2 onwards a new register got added to read last
code word.Add support for this READ_LOCATION_LAST_CW_n
register.

In the case of QPIC v2, codewords 0, 1 and 2 will be accessed
through READ_LOCATION_n, while codeword 3 will be accessed
through READ_LOCATION_LAST_CW_n.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-5-git-send-email-mdalam@codeaurora.org

Create a nandc_set_read_loc() helper to abstract the
configuration of the location register.

QPIC v2 onwards features a separate location register
for the last codeword, so introducing this extra helper
which will simplify the addition of QPIC v2 support.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-4-git-send-email-mdalam@codeaurora.org

Rename the parameters of the nandc_set_read_loc() macro
to avoid the confusion between is_last_read_loc which
is last location in a read code word and last_cw which
is last code word of a page data.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-3-git-send-email-mdalam@codeaurora.org

Add the qcom_nandc_is_last_cw() helper which checks if
the input cw index is the last one or not.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-2-git-send-email-mdalam@codeaurora.org

This change will convert nandc to chip in Read/Write helper, this
change is needed because if we wnated to access number of steps
in Read/Write helper then we need to get the chip->ecc.steps,
currentlly its not possible.After this change we can directly
acces chip->ecc.steps in Read/Write helper.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-1-git-send-email-mdalam@codeaurora.org

If dma_request_channel() fails then the probe fails and it should
return a negative error code, but currently it returns success.

fixes: 4774fb0a ("mtd: nand/fsmc: Add DMA support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YCqaOZ83OvPOzLwh@mwanda

The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.

As the overlaps are huge, variable names have been generalized
accordingly.

Apart from the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.

New hardware features are not supported, namely:
 - Power on reset
 - Unique ID
 - Double transfer rate (DTR)
 - Parameter page
 - Random data quad IO

The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.

The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.

Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210211113619.3502-1-code@reto-schneider.ch

On success nand_exec_prog_page_op() returns the NAND status byte, but on
failure it returns a negative error code. nand_prog_page_op() interprets
the return value as NAND status byte without error checking.  This means
a failure in nand_exec_prog_page_op() can go through unnoticed.

The straight forward fix would be to add the missing error checking. To
clean the code a bit we can move the nand status check to
nand_prog_page_op().  This way we can get rid of the overloaded return
value from nand_exec_prog_page_op() and return a plain error code which
is less error prone.

nand_exec_prog_page_op() is only called from one other place and in this
call the 'prog' parameter is false in which case the nand status check
is skipped, so it's correct to not add the NAND status check there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210205142725.13225-2-s.hauer@pengutronix.de

On success chip->legacy.waitfunc() returns the NAND status byte, but on
failure it returns a negative error code. This was never tested for and
instead the return value was interpreted as NAND status without error
checking. Add the missing error check.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210205142725.13225-1-s.hauer@pengutronix.de

This change will remove unused register name macro NAND_DEV1_ECC_CFG.
Since this register was only available in QPIC version 1.4.20 ipq40xx
and it was not used. In QPIC version 1.5 on wards this register got
removed.In QPIC version 2.0 0x2c offset is updated with register
NAND_AUTO_STATUS_EN So adding this register macro NAND_AUTO_STATUS_EN
with offset 0x2c.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1612037236-7954-1-git-send-email-mdalam@codeaurora.org

The software Hamming ECC engine stores the nsteps variable in its own
private structure while it is also exported as a public ECC field.

Let's get rid of the redundant private one and let's use the
nand_ecc_context structure when possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-10-miquel.raynal@bootlin.com

The software BCH ECC engine stores the nsteps variable in its own
private structure while it is also exported as a public ECC field.

Let's get rid of the redundant private one and let's use the
nand_ecc_context structure when possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-9-miquel.raynal@bootlin.com

As part of a previous fix, we imported the BCH internal structure in
order to get information about the BCH engine configuration.

It is best not to access private structure so instead, a small rework
has been done to export more information from the ECC engines. Now,
let's use these.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-8-miquel.raynal@bootlin.com

Most of the time, there is no need to use the software ECC Hamming and
BCH algorithms private context to know their configuration. All the
data has been stored by their ->init_ctx() hook in the generic NAND
ECC engine structure, so use this one when possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-7-miquel.raynal@bootlin.com

This operation is very common and deserves a helper. It of course only
works after the ECC engine initialization.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-6-miquel.raynal@bootlin.com

This operation is very common and deserves a helper. It of course only
works after the ECC engine initialization.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-5-miquel.raynal@bootlin.com

Advertize the actual number of steps that will actually be used by the
driver by populating the public field.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-4-miquel.raynal@bootlin.com

Advertize the actual number of steps that will actually be used by the
driver by populating the public field.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-3-miquel.raynal@bootlin.com

This is an information that might be useful for specific uses, so
export it, which might avoid having to guess the number of steps when
necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-2-miquel.raynal@bootlin.com

Pull rdma fixes from Jason Gunthorpe:
 "Nothing special here, though Bob's regression fixes for rxe would have
  made it before the rc cycle had there not been such strong winter
  weather!

   - Fix corner cases in the rxe reference counting cleanup that are
     causing regressions in blktests for SRP

   - Two kdoc fixes so W=1 is clean

   - Missing error return in error unwind for mlx5

   - Wrong lock type nesting in IB CM"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/rxe: Fix errant WARN_ONCE in rxe_completer()
  RDMA/rxe: Fix extra deref in rxe_rcv_mcast_pkt()
  RDMA/rxe: Fix missed IB reference counting in loopback
  RDMA/uverbs: Fix kernel-doc warning of _uverbs_alloc
  RDMA/mlx5: Set correct kernel-doc identifier
  IB/mlx5: Add missing error code
  RDMA/rxe: Fix missing kconfig dependency on CRYPTO
  RDMA/cm: Fix IRQ restore in ib_send_cm_sidr_rep

Pull gcc-plugins fixes from Kees Cook:
 "Tiny gcc-plugin fixes for v5.12-rc2. These issues are small but have
  been reported a couple times now by static analyzers, so best to get
  them fixed to reduce the noise. :)

   - Fix coding style issues (Jason Yan)"

* tag 'gcc-plugins-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: latent_entropy: remove unneeded semicolon
  gcc-plugins: structleak: remove unneeded variable 'ret'

Pull pstore fixes from Kees Cook:

 - Rate-limit ECC warnings (Dmitry Osipenko)

 - Fix error path check for NULL (Tetsuo Handa)

* tag 'pstore-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/ram: Rate-limit "uncorrectable error in header" message
  pstore: Fix warning in pstore_kill_sb()

Merge tag 'for-5.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:
 "Fix DM verity target's optional Forward Error Correction (FEC) for
  Reed-Solomon roots that are unaligned to block size"

* tag 'for-5.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm verity: fix FEC for RS roots unaligned to block size
  dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size

Pull block fixes from Jens Axboe:

 - NVMe fixes:
      - more device quirks (Julian Einwag, Zoltán Böszörményi, Pascal
        Terjan)
      - fix a hwmon error return (Daniel Wagner)
      - fix the keep alive timeout initialization (Martin George)
      - ensure the model_number can't be changed on a used subsystem
        (Max Gurtovoy)

 - rsxx missing -EFAULT on copy_to_user() failure (Dan)

 - rsxx remove unused linux.h include (Tian)

 - kill unused RQF_SORTED (Jean)

 - updated outdated BFQ comments (Joseph)

 - revert work-around commit for bd_size_lock, since we removed the
   offending user in this merge window (Damien)

* tag 'block-5.12-2021-03-05' of git://git.kernel.dk/linux-block:
  nvmet: model_number must be immutable once set
  nvme-fabrics: fix kato initialization
  nvme-hwmon: Return error code when registration fails
  nvme-pci: add quirks for Lexar 256GB SSD
  nvme-pci: mark Kingston SKC2000 as not supporting the deepest power state
  nvme-pci: mark Seagate Nytro XM1440 as QUIRK_NO_NS_DESC_LIST.
  rsxx: Return -EFAULT if copy_to_user() fails
  block/bfq: update comments and default value in docs for fifo_expire
  rsxx: remove unused including <linux/version.h>
  block: Drop leftover references to RQF_SORTED
  block: revert "block: fix bd_size_lock use"