Hariprasad Kelam says:

====================
Externel ptp clock support

Externel ptp support is required in a scenario like connecting
a external timing device to the chip for time synchronization.
This series of patches adds support to ptp driver to use external
clock and enables PTP config in CN10K MAC block (RPM). Currently
PTP configuration is left unchanged in FLR handler these patches
addresses the same.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
,

PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The input clock frequency of PTP block is figured
out from hardware reset block currently. The firmware
data already has this info in sclk. Hence simplify
ptp driver to use sclk from firmware data.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.

Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon receiving ptp config request from netdev interface , Octeontx2 MAC
block CGX is configured to append timestamp to every incoming packet
and NPC config is updated with DMAC offset change.

Currently this configuration is not reset in FLR handler. This patch
resets the same.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IV of CCM mode has special requirements, this patch supports CCM
mode of SM4 algorithm.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kbuild supports <modname>-y as well as <modname>-objs.
This simplifies the Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Assign the objects directly to obj-$(CONFIG_INET).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

My previous patch had an off-by-one error in the added sanity
check, the arrays are MTL_MAX_{RX,TX}_QUEUES long, so if that
index is that number, it has overflown.

The patch silenced the warning anyway because the strings could
no longer overlap with the input, but they could still overlap
with other fields.

Fixes: 3e0d5699 ("net: stmmac: fix gcc-10 -Wrestrict warning")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

clang warns about arithmetic on NULL pointers:

drivers/net/ethernet/ti/am65-cpsw-ethtool.c:71:2: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
        AM65_CPSW_REGDUMP_REC(AM65_CPSW_REGDUMP_MOD_NUSS, 0x0, 0x1c),
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/am65-cpsw-ethtool.c:64:29: note: expanded from macro 'AM65_CPSW_REGDUMP_REC'
        .hdr.len = (((u32 *)(end)) - ((u32 *)(start)) + 1) * sizeof(u32) * 2 + \
                                   ^ ~~~~~~~~~~~~~~~~

The expression here is easily changed to a calculation based on integers
that is no less readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When rhashtable_init() fails, it returns -EINVAL.
However, since error return value of rhashtable_init is not checked,
it can cause use of uninitialized pointers.
So, fix unhandled errors of rhashtable_init.
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: bcmgenet: support for flow control

This patch series adds support for flow control to the GENET driver, the
first 2 patches remove superfluous code, the 3rd one does re-organize
code a little bit and the 4th one ads the support for flow control
proper.
====================

This commit extends the supported ethtool operations to allow MAC
level flow control to be configured for the bcmgenet driver.

The ethtool utility can be used to change the configuration of
auto-negotiated symmetric and asymmetric modes as well as manually
configuring support for RX and TX Pause frames individually.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit separates out the MAC configuration that occurs on a
PHY state change into a function named bcmgenet_mac_config().

This allows the function to be called directly elsewhere.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY state machine has been fixed to only call the adjust_link
callback when the link state has changed. Therefore the old link
state variables are no longer needed to detect a change in link
state.

This commit effectively reverts
commit 5ad6e6c5 ("net: bcmgenet: improve bcmgenet_mii_setup()")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bcmgenet_mii_setup() function is registered as the adjust_link
callback from the phylib for the GENET driver.

The phylib always sets the netif_carrier according to phydev->link
prior to invoking the adjust_link callback, so there is no need to
repeat that in the link down case within the network driver.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linus Walleij says:

====================
RTL8366(RB) cleanups part 1

This is a first set of patches making the RTL8366RB work out of
the box with a default OpenWrt userspace.

We achieve bridge port isolation with the first patch, and the
next 5 patches removes the very weird VLAN set-up with one
VLAN with PVID per port that has been in this driver in all
vendor trees and in OpenWrt for years.

The switch is now managed the way a modern bridge/DSA switch
shall be managed.

After these patches are merged, I will send the next set which
adds new features, some which have circulated before.

ChangeLog v4->v5:
- Drop the patch disabling 4K VLAN.
- Drop the patch forcing VLAN0 untagged.
- Fix a semantic bug in the filer enablement code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need a message for every VLAN association, dbg
is fine. The message about adding the DSA or CPU
port to a VLAN is directly misleading, this is perfectly
fine.

Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We were checking that the MC (member config) was != 0
for some reason, all we need to check is that the config
has no ports, i.e. no members. Then it can be recycled.
This must be some misunderstanding.

Fixes: 4ddcaf1e ("net: dsa: rtl8366: Properly clear member config")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.

The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.

Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While we were defining one VLAN per port for isolating the ports
the port_vlan_filtering() callback was implemented to enable a
VLAN on the port + 1. This function makes no sense, not only is
it incomplete as it only enables the VLAN, it doesn't do what
the callback is supposed to do, which is to selectively enable
and disable filtering on a certain port.

Implement the correct callback: we have two registers dealing
with filtering on the RTL9366RB, so we implement an ASIC-specific
callback and implement filering using the register bit that makes
the switch drop frames if the port is not in the VLAN member set.

The DSA documentation Documentation/networking/switchdev.rst states:

  When the bridge has VLAN filtering enabled and a PVID is not
  configured on the ingress port, untagged and 802.1p tagged
  packets must be dropped. When the bridge has VLAN filtering
  enabled and a PVID exists on the ingress port, untagged and
  priority-tagged packets must be accepted and forwarded according
  to the bridge's port membership of the PVID VLAN. When the
  bridge has VLAN filtering disabled, the presence/lack of a
  PVID should not influence the packet forwarding decision.

To comply with this, we add two arrays of bool in the RTL8366RB
state that keeps track of if filtering and PVID is enabled or
not for each port. We then add code such that whenever filtering
or PVID changes, we update the filter according to the
specification.

Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This hacky default VLAN setup was done in order to direct
packets to the right ports and provide port isolation, both
which we now support properly using custom tags and proper
bridge port isolation.

We can drop the custom VLAN code and leave all VLAN handling
alone, as users expect things to be. We can also drop
ds->configure_vlan_while_not_filtering = false; and let
the core deal with any VLANs it wants.

Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use port isolation registers to configure bridge offloading.

Tested on the D-Link DIR-685, switching between ports and
sniffing ports to make sure no packets leak.

Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Move devlink_register to be last devlink command

This is second version of patch series
https://lore.kernel.org/netdev/cover.1628599239.git.leonro@nvidia.com/

The main change is addition of delayed notification logic that will
allowed us to delete devlink_params_publish API (future series will
remove it completely) and conversion of all drivers to have devlink_register
being last commend.

The series itself is pretty straightforward, except liquidio driver
which performs initializations in various workqueues without proper
locks. That driver doesn't hole device_lock and it is clearly broken
for any parallel driver core flows (modprobe + devlink + PCI reset will
100% crash it).

In order to annotate devlink_register() will lockdep of holding
device_lock, I added workaround in this driver.

Thanks

----------------------
From previous cover letter:
Hi Dave and Jakub,

This series prepares code to remove devlink_reload_enable/_disable API
and in order to do, we move all devlink_register() calls to be right
before devlink_reload_enable().

The best place for such a call should be right before exiting from
the probe().

This is done because devlink_register() opens devlink netlink to the
users and gives them a venue to issue commands before initialization
is finished.

1. Some drivers were aware of such "functionality" and tried to protect
themselves with extra locks, state machines and devlink_reload_enable().
Let's assume that it worked for them, but I'm personally skeptical about
it.

2. Some drivers copied that pattern, but without locks and state
machines. That protected them from reload flows, but not from any _set_
routines.

3. And all other drivers simply didn't understand the implications of early
devlink_register() and can be seen as "broken".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink
is fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured. Indirectly this change fixes the commit mentioned
below where devlink_unregister() was prematurely removed.

Fixes: db4278c5 ("devlink: Make devlink_register to be void")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Open user space access to the devlink after driver is probed.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Open access to the devlink interface when the driver fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that devlink is open to receive user input when all
parameters are initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The change of devlink_alloc() to accept device makes sure that device
is fully initialized and device_register() does nothing except allowing
users to use that devlink instance.

Such change ensures that no user input will be usable till that point and
it eliminates the need to worry about internal locking as long as devlink_register
is called last since all accesses to the devlink are during initialization.

This change fixes the following lockdep warning.

 ======================================================
 WARNING: possible circular locking dependency detected
 5.14.0-rc2+ #27 Not tainted
 ------------------------------------------------------
 devlink/265 is trying to acquire lock:
 ffff8880133c2bc0 (&dev->intf_state_mutex){+.+.}-{3:3}, at: mlx5_unload_one+0x1e/0xa0 [mlx5_core]
 but task is already holding lock:
 ffffffff8362b468 (devlink_mutex){+.+.}-{3:3}, at: devlink_nl_pre_doit+0x2b/0x8d0
 which lock already depends on the new lock.
 the existing dependency chain (in reverse order) is:

 -> #1 (devlink_mutex){+.+.}-{3:3}:
        __mutex_lock+0x149/0x1310
        devlink_register+0xe7/0x280
        mlx5_devlink_register+0x118/0x480 [mlx5_core]
        mlx5_init_one+0x34b/0x440 [mlx5_core]
        probe_one+0x480/0x6e0 [mlx5_core]
        pci_device_probe+0x2a0/0x4a0
        really_probe+0x1cb/0xba0
        __driver_probe_device+0x18f/0x470
        driver_probe_device+0x49/0x120
        __driver_attach+0x1ce/0x400
        bus_for_each_dev+0x11e/0x1a0
        bus_add_driver+0x309/0x570
        driver_register+0x20f/0x390
        0xffffffffa04a0062
        do_one_initcall+0xd5/0x400
        do_init_module+0x1c8/0x760
        load_module+0x7d9d/0xa4b0
        __do_sys_finit_module+0x118/0x1a0
        do_syscall_64+0x3d/0x90
        entry_SYSCALL_64_after_hwframe+0x44/0xae

 -> #0 (&dev->intf_state_mutex){+.+.}-{3:3}:
        __lock_acquire+0x2999/0x5a40
        lock_acquire+0x1a9/0x4a0
        __mutex_lock+0x149/0x1310
        mlx5_unload_one+0x1e/0xa0 [mlx5_core]
        mlx5_devlink_reload_down+0x185/0x2b0 [mlx5_core]
        devlink_reload+0x1f2/0x640
        devlink_nl_cmd_reload+0x6c3/0x10d0
        genl_family_rcv_msg_doit+0x1e9/0x2f0
        genl_rcv_msg+0x27f/0x4a0
        netlink_rcv_skb+0x11e/0x340
        genl_rcv+0x24/0x40
        netlink_unicast+0x433/0x700
        netlink_sendmsg+0x6fb/0xbe0
        sock_sendmsg+0xb0/0xe0
        __sys_sendto+0x192/0x240
        __x64_sys_sendto+0xdc/0x1b0
        do_syscall_64+0x3d/0x90
        entry_SYSCALL_64_after_hwframe+0x44/0xae

 other info that might help us debug this:

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(devlink_mutex);
                                lock(&dev->intf_state_mutex);
                                lock(devlink_mutex);
   lock(&dev->intf_state_mutex);

  *** DEADLOCK ***

 3 locks held by devlink/265:
  #0: ffffffff836371d0 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40
  #1: ffffffff83637288 (genl_mutex){+.+.}-{3:3}, at: genl_rcv_msg+0x31a/0x4a0
  #2: ffffffff8362b468 (devlink_mutex){+.+.}-{3:3}, at: devlink_nl_pre_doit+0x2b/0x8d0

 stack backtrace:
 CPU: 0 PID: 265 Comm: devlink Not tainted 5.14.0-rc2+ #27
 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
 Call Trace:
  dump_stack_lvl+0x45/0x59
  check_noncircular+0x268/0x310
  ? print_circular_bug+0x460/0x460
  ? __kernel_text_address+0xe/0x30
  ? alloc_chain_hlocks+0x1e6/0x5a0
  __lock_acquire+0x2999/0x5a40
  ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0
  ? add_lock_to_list.constprop.0+0x6c/0x530
  lock_acquire+0x1a9/0x4a0
  ? mlx5_unload_one+0x1e/0xa0 [mlx5_core]
  ? lock_release+0x6c0/0x6c0
  ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0
  ? lock_is_held_type+0x98/0x110
  __mutex_lock+0x149/0x1310
  ? mlx5_unload_one+0x1e/0xa0 [mlx5_core]
  ? lock_is_held_type+0x98/0x110
  ? mlx5_unload_one+0x1e/0xa0 [mlx5_core]
  ? find_held_lock+0x2d/0x110
  ? mutex_lock_io_nested+0x1160/0x1160
  ? mlx5_lag_is_active+0x72/0x90 [mlx5_core]
  ? lock_downgrade+0x6d0/0x6d0
  ? do_raw_spin_lock+0x12e/0x270
  ? rwlock_bug.part.0+0x90/0x90
  ? mlx5_unload_one+0x1e/0xa0 [mlx5_core]
  mlx5_unload_one+0x1e/0xa0 [mlx5_core]
  mlx5_devlink_reload_down+0x185/0x2b0 [mlx5_core]
  ? netlink_broadcast_filtered+0x308/0xac0
  ? mlx5_devlink_info_get+0x1f0/0x1f0 [mlx5_core]
  ? __build_skb_around+0x110/0x2b0
  ? __alloc_skb+0x113/0x2b0
  devlink_reload+0x1f2/0x640
  ? devlink_unregister+0x1e0/0x1e0
  ? security_capable+0x51/0x90
  devlink_nl_cmd_reload+0x6c3/0x10d0
  ? devlink_nl_cmd_get_doit+0x1e0/0x1e0
  ? devlink_nl_pre_doit+0x72/0x8d0
  genl_family_rcv_msg_doit+0x1e9/0x2f0
  ? __lock_acquire+0x15e2/0x5a40
  ? genl_family_rcv_msg_attrs_parse.constprop.0+0x240/0x240
  ? mutex_lock_io_nested+0x1160/0x1160
  ? security_capable+0x51/0x90
  genl_rcv_msg+0x27f/0x4a0
  ? genl_get_cmd+0x3c0/0x3c0
  ? lock_acquire+0x1a9/0x4a0
  ? devlink_nl_cmd_get_doit+0x1e0/0x1e0
  ? lock_release+0x6c0/0x6c0
  netlink_rcv_skb+0x11e/0x340
  ? genl_get_cmd+0x3c0/0x3c0
  ? netlink_ack+0x930/0x930
  genl_rcv+0x24/0x40
  netlink_unicast+0x433/0x700
  ? netlink_attachskb+0x750/0x750
  ? __alloc_skb+0x113/0x2b0
  netlink_sendmsg+0x6fb/0xbe0
  ? netlink_unicast+0x700/0x700
  ? netlink_unicast+0x700/0x700
  sock_sendmsg+0xb0/0xe0
  __sys_sendto+0x192/0x240
  ? __x64_sys_getpeername+0xb0/0xb0
  ? do_sys_openat2+0x10a/0x370
  ? down_write_nested+0x150/0x150
  ? do_user_addr_fault+0x215/0xd50
  ? __x64_sys_openat+0x11f/0x1d0
  ? __x64_sys_open+0x1a0/0x1a0
  __x64_sys_sendto+0xdc/0x1b0
  ? syscall_enter_from_user_mode+0x1d/0x50
  do_syscall_64+0x3d/0x90
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7f50b50b6b3a
 Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c
 RSP: 002b:00007fff6c0d3f38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
 RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007f50b50b6b3a
 RDX: 0000000000000038 RSI: 000055763ac08440 RDI: 0000000000000003
 RBP: 000055763ac08410 R08: 00007f50b5192200 R09: 000000000000000c
 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
 R13: 0000000000000000 R14: 000055763ac08410 R15: 000055763ac08440
 mlx5_core 0000:00:09.0: firmware version: 4.8.9999
 mlx5_core 0000:00:09.0: 0.000 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x255 link)
 mlx5_core 0000:00:09.0 eth1: Link up

Fixes: a6f3b623 ("net/mlx5: Move devlink registration before interfaces load")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor the code to make sure that devlink_register() is the last
command during initialization stage.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate devlink registrations and traps registrations so devlink will
be registered when driver is fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>